Search

High voltage direct current (HVdc) power transmission systems do not encounter any natural zero crossing unlike the ac systems, and hence, the dc circuit breakers employed should be fast-acting and reliable to ensure safe operation. Circuit breakers (CBs) that have fast response time with lower energy loss dissipation are required for subsea HVdc transmission systems. This article investigates the performance of various CB topologies, including ultrafast coupled inductor hybrid CB (CIHCB) topology without and with the integration of resistive-type superconducting fault current limiter (R-SFCL) for a 100-kV, 100-MW HVdc transmission systems. It is found that the addition of R-SFCL with 1.7-ms response time decreases the peak current through the breaker and, hence, the power dissipated in the CB during short-circuit fault conditions. Thus, the rating of CB can be significantly decreased with the proposed topology. Furthermore, a comparison of power loss in CIHCB with the existing topologies, such as mechanical CB, resonant CB, and HVdc-hybrid CB, are also presented in this article. [ABSTRACT FROM AUTHOR]

High-voltage direct current (HVDC) circuit breaker development and deployment strongly depend on the testing process, which ensures that the HVDC circuit breakers will satisfy design requirements. This article presents an HVDC circuit breaker test bench circuit configuration that can provide controllable large output currents to simulate different fault conditions for the current breaking test and high output voltage for the dielectric withstand test. The current breaking test circuit is based on multiple cascaded power converters connected in parallel to provide the necessary output current capability. Each cascaded power converter is composed of multiple cells that are operated by a phase-shifted pulsewidth-modulated signal for greater controllability and higher quality of the output waveform. The dielectric withstand test circuit is a simple high-voltage source with a low power rating that can also be used to charge the test bench and the internal circuitry of the circuit breaker that is to be tested. The proposed test bench ensures that fault conditions can be replicated accurately and offers greater flexibility by being able to test mechanical, semiconductor-based, or hybrid HVDC circuit breakers with different current and voltage ratings on the same hardware without any changes. The idea and the operating principle of the proposed test bench are verified experimentally on a downscaled system that consists of three cascaded power converters connected in parallel with three cells per cascaded power converter and with a total equivalent switching frequency of 92.5 kHz. [ABSTRACT FROM AUTHOR]

The reliability of meshed DC grids mainly relies on their ability in DC fault protection and line power flow managing. Multiple DC circuit breakers (DCCB) and current flow controller (CFC) need to be installed, which significantly increases the system cost. A novel current flow controller integrated with hybrid dc circuit breaker (CFC-IHCB) is proposed to significantly reduce the loss and cost of the whole system. Only one unidirectional IGBT string based main breaker branch is needed for n lines, and the CFC function is integrated into the load communication switches (LCSs). The basic working principle of proposed topology is presented and analyzed. The functionality is verified and a comparison of the proposed solution and other DCCB/CFC solutions is given based on a multi-terminal HVDC system case study. [ABSTRACT FROM AUTHOR]

In this article, metal oxide varistor (MOV) design optimization and switching control in the main circuit breaker (MCB) branch of a progressively switched hybrid dc circuit breaker (DCCB) is presented. A progressively switched hybrid DCCB can achieve faster fault isolation with reduced peak fault current magnitude and transient recovery voltage compared with a regular hybrid DCCB due to its modified switching strategy. Consequently, thermal stress on the semiconductor devices in MCB is significantly reduced. Analytical model of the system dynamics during fault isolation with progressive switching is derived to demonstrate the switching scheme’s effect on the energy-absorbing component, MOV, during turn-off process. Derived analytical model in conjunction with the displacement curve of the fast mechanical switch of the hybrid DCCB is utilized to optimize the components of the main circuit breaker branch to reduce MOV degradation through asymmetric energy dissipation. A model of the circuit breaker is built in PSCAD to validate the performance of the proposed optimization method in a 10-kV/250-A system with four stage progressive switching. Additionally, a low voltage system model at 380 V is developed in PLECS for two stage progressive switching that works as the basis of experimental validation. This includes both lookup table-based MOV model and device thermal model for junction temperature estimation. Experimental results are provided for a 380-V system to demonstrate reduced fault current peak in a progressive switching and near uniform energy absorption in optimally selected MOVs. [ABSTRACT FROM AUTHOR]

The hybrid dc circuit breaker is one of the most promising dc circuit breakers (DCCBs). However, its cost is relatively high, and the completion of its fault isolation is significantly delayed because of the large current limiting inductors configured in the multiterminal dc grid. Besides, due to the utilization of overhead lines, the probability of temporary faults is much increased, which means there is a great possibility that the power supply can be rapidly restored by reclosing DCCBs. However, the temporary faults must be distinguished from the permanent faults before the reclosing operation to avoid damaging the fragile power electronic equipment. Therefore, considering the above issues, a novel multiport hybrid dc circuit breaker (MHCB) is proposed in this article. The MHCB mainly has three advantages: the reduced implementation cost by sharing the expensive main breaker among multiple lines, the reduced fault isolation time by bypassing the current limiting inductor during energy dissipation, and the ability to reclose softly. Extensive simulations and experiments verify the effectiveness of the device. In addition, the comparison of the new device and existed solutions is presented. [ABSTRACT FROM AUTHOR]

Flexible DC grids with dedicated metallic return (DMR) encounter two major challenges when reclosing hybrid DC circuit breakers (DCCBs): (1) identifying permanent and nonpermanent faults to determine whether DCCBs should be reclosed; and (2) identifying pole-to-ground (P-GND) and pole-to-DMR (P-DMR) faults to determine whether all DC lines should be isolated when a permanent fault occurs. Under a permanent P-DMR fault, all DC transmission lines should be isolated instead of maintaining half of the power transmission. In this study, the equivalent circuits and analytical expressions of the fault currents under the P-GND and P-DMR faults are deduced. On this basis, two different criteria are proposed to discriminate these two faults. Permanent and nonpermanent faults are recognized according to the characteristics of the residual voltage of the DC transmission line. Finally, a comprehensive reclosing strategy considering fault type discrimination for a hybrid DCCB is developed. A simulation model of a four-end flexible HVDC grid with DMR is constructed in PSCAD/EMTDC. The validity of the proposed reclosing strategy is verified through different simulation cases. [ABSTRACT FROM AUTHOR]

Hybrid dc circuit breakers (HCBs) are recognized as suitable devices for protecting high-voltage direct-current (HVDC) systems, along with other dc circuit breakers (DCCB). However, compared to mechanical circuit breakers, HCBs exhibit higher conduction losses. Such losses are inevitable under no-fault conditions as current may flow through some of the semiconductor switches. An integrated circuit breaker (ICB) minimizing these losses is presented in this paper, and this is achieved by replacing semiconductor switches by mechanical components in the current path. For completeness, the topology design, operating sequence and a mathematical analysis for component sizing of the device are provided. In addition, an estimation of the conduction losses is quantified. It is estimated that the power losses of an ICB are 2 to 30% of an HCB only. The ICB has been implemented in PSCAD/EMTDC to demonstrate its effectiveness for isolating dc faults, with simulations conducted on a three-terminal HVDC grid. [ABSTRACT FROM AUTHOR]

Hybrid circuit breaker (HCB) has shown good performance for interrupting dc fault current. However, a massive number of IGBTs in series is needed. These will lead to high costs and significant difficulty in balancing IGBT dynamic voltage. This paper proposes a bidirectional hybrid circuit breaker based on a cascaded half-bridge submodule structure to reduce the overall costs and implementation difficulty of HCB. The number of IGBTs is reduced by 50%, and the operating speed is fast enough. A model of a four-terminal modular multilevel converter (MMC) system with a proposed hybrid circuit breaker in different stages is developed to describe the fault blocking process more clearly. The performance of the proposed HCB is validated and compared with other HCB structure through both theoretical derivation and time-domain simulation. [ABSTRACT FROM AUTHOR]