Search

It has been widely accepted to apply dc circuit breakers (DCCBs) to protect dc grids. Nevertheless, existing DCCBs have one or more following limitations: insulation recovery scheme of mechanical switch, additional precharge power supply, high conduction loss, unreliable current-breaking process, and unidirectional design. In this letter, a new DCCB with low conduction loss, simple precharging scheme, and reliable breaking ability is proposed. The proposed DCCB could break both fault and operating current actively with the same simple operation sequences. Moreover, bidirectional topology possessing all advantages mentioned previously is also presented. Topology introduction, parameters designing, and scaled-down experiment of the proposed DCCB are all presented in the letter. [ABSTRACT FROM AUTHOR]

The reliability of meshed DC grids mainly relies on their ability in DC fault protection and line power flow managing. Multiple DC circuit breakers (DCCB) and current flow controller (CFC) need to be installed, which significantly increases the system cost. A novel current flow controller integrated with hybrid dc circuit breaker (CFC-IHCB) is proposed to significantly reduce the loss and cost of the whole system. Only one unidirectional IGBT string based main breaker branch is needed for n lines, and the CFC function is integrated into the load communication switches (LCSs). The basic working principle of proposed topology is presented and analyzed. The functionality is verified and a comparison of the proposed solution and other DCCB/CFC solutions is given based on a multi-terminal HVDC system case study. [ABSTRACT FROM AUTHOR]

Long pulse gas lasers utilizing double-discharge circuits are different from the single-short pulse gas lasers in that they do not require all of the desired energy to be deposited into the peaking capacitors prior to ignition of the main gap. Instead, the majority of the energy is held in another capacitor that is then discharged in the form of a longer duration discharge pulse output compared with that of single-short pulse lasers. Extended stability of the discharge is typically achieved by igniting the main gap discharge at higher ignition voltages. Several double-discharge circuit topologies exist in the literature. However, each topology has its own disadvantages primarily centered around the components needed and the resulting complexity. In this article we introduce the application of the new hybrid circuit pulsed power topology as a double-discharge circuit with high ignition voltages. The hybrid circuit pulsed power topology was originally published by the authors of this article in their previous publication titled “A New Hybrid Pulsed Power Circuit Topology for Gas Laser Applications.” The advantage of the hybrid circuit as a double-discharge circuit is that it does not require any special device [e.g., semiconductor opening switch (SOS) diode] and can use commonly available components. [ABSTRACT FROM AUTHOR]

Two key challenges in meshed multi-terminal dc (MTdc) grids are line power flow management and fault current interruption, which can be solved by current flow controllers (CFCs) and hybrid dc circuit breakers (HCBs), respectively. However, the power losses and the implementation costs of CFCs and HCBs are relatively high. In order to overcome these drawbacks, a combined HCB (CHCB) is proposed in this article by fully utilizing the core ideas of the interline dual H-bridge CFC and the HCB. The proposed device can substitute multiple HCBs at a dc bus with greatly reduced cost. In addition to the fault current interruption capability, the current flows in the adjacent lines can be controlled by the embedded multi-line CFC in the CHCB expanded from the existing interline dual H-bridge CFC. The system-level behavior of the proposed CHCB is similar to the separate solution of the typical HCB and the multi-line CFC. Extensive simulations and experiments verify the effectiveness of the proposed device. Besides, a comparison of the proposed CHCB and the separate solution is presented. [ABSTRACT FROM AUTHOR]

A mechanical switch can be used instead of a power electronic load commutation switch in orderto reduce the losses during normal power flow in standard hybrid DC circuit breakers. The success of current commutation in such hybrid breakers depends on the arc voltage formed across the contacts in the mechanical switch. The behaviour of rapidly elongated, wall constricted arcsgenerated during the opening of an ultra-fast mechanical switch in the air is studied here. The voltage-current characteristics of the generated arcs are obtained for steady state contact opening velocities of 6, 11 and 21 m/s. It is found that the arc voltage at a given current and contact separation increases with the contact opening velocity. It is shown that stationary,zero-contact-velocity characteristics can not be used to accurately quantify the voltage build-up in fast elongating arcs in hybrid breakers. A best-fitting black-box equation for the dynamic arc characteristics is presented for the tested velocities. The obtained voltage-current characteristics are used as input to simulate the current commutation process in a 12 kV hybridDC circuit breaker case-study. Different scenarios of current commutation failure related to the arc voltage build up are identified. It is shown that these failures scenarios can be avoided by increasing the contact opening velocity. [ABSTRACT FROM AUTHOR]