Search

As a typical representative of the stator permanent magnet (PM) machines, the flux reversal machines (FRMs) have a simple structure, high availability of PMs, and high efficiency, making them suitable for direct drive applications. However, the PMs of the FRMs are mounted on the surface of the stator tooth, and its equivalent length of air gap is relatively large, which limits the torque increase. To improve the torque density, a novel FRM with auxiliary teeth is proposed in this paper. Half of the stator teeth are replaced by auxiliary teeth without PMs to reduce magnetic flux leakage, the number of PMs on each stator tooth is also changed. To improve the torque, the genetic algorithm is used to optimize the key design parameters to determine the optimal parameters of the machine. Finally, a finite element model is established to verify the analysis results. Compared with the conventional FRM, the torque of the proposed FRM is increased by 25.1%, the torque ripple is reduced by 24.1%, and the consumption of PMs is reduced by 24.1%. Therefore, the proposed FRM has a broader application prospect. [ABSTRACT FROM AUTHOR]

Spoke structure can increase the torque density of coaxial magnetic gear (CMG). However, the outer rotor can produce a large number of magnetic leakages. To improve the utility of PMs, a novel magnetic gear was proposed in this paper. The structure of the auxiliary flux modulator is a slotted iron yoke, and the slot angle is same as the stationary ring. Among, the permanent magnets (PMs) of inner rotor are adopted uneven block structure to improve air gap flux density. At the same time, the stationary ring adopts high-temperature superconducting (HTS) bulks, replacing the epoxy resin. In addition, Genetic algorithm (GA) is applied to calculate the optimal parameters of the proposed CMG. Finally, the air gap flux density and output torque of the magnetic gear a compared by the finite element method. The results show that the output torque of the proposed magnetic gear is effectively improved. [ABSTRACT FROM AUTHOR]

For tackling the problem of large errors in simulating the static inner symmetrical minor hysteresis loops through the Simplified Landau-Lifshitz-Gilbert (S-LLG) equation, a modification by improving the grain structure arrangement and introducing additional hysteresis energy function is proposed. With the proposed model, only a unified set of parameters identified by four static hysteresis loops is needed to predict hysteresis loops under arbitrarily different magnetic flux density levels. To verify the global simulation capability of the proposed model, the simulation results of hysteresis loops are compared with the measured data of a grain-oriented (GO) steel. The obtained results show that the model has good simulation ability for hysteresis loops under different magnetic flux densities for both sinusoidal and harmonic excitation conditions. [ABSTRACT FROM AUTHOR]

To clarify the mechanism of the magnetic properties deterioration and the increasing loss of the Grain-Oriented (GO) electrical steel wound cores under serving conditions, the effect of the bending stress in a wide frequency range should be thoroughly investigated. In this paper, a magnetic properties measuring system for GO electrical steel under different bending stress from 50 Hz to 1000 Hz is proposed. To ensure the accuracy and reproductivity of the measurements, the waveform of magnetic flux densities should be controlled to be sinusoidal. However, the bending stress aggravates the material's nonlinear properties, making waveform control very difficult. To solve this problem, a frequency-domain adaptive dual-loop feedback control algorithm is developed. Obtained results show that the proposed method has a good effect on waveform control under bending stress, and the loss of the material under different magnetizing conditions is then analyzed. [ABSTRACT FROM AUTHOR]

Based on the consideration of the magnetic domain motion under different magnetization levels, an improved J-A model with variable parameters is proposed to solve the problem of significant errors in the process of calculating the inner symmetric small loops. The proposed method introduces a variable scale parameter v(B) to correct the irreversible magnetization component of the J-A model. Meanwhile, based on the magnetic domain theory, a method with variable pinning parameter k(B) and a variable domain wall bending parameter c(B) is proposed. By comparing the measured data of B30P105 Grain-Oriented (GO) silicon steel, the calculation error for each magnetization level of the model is within 7%, which means that the global hysteresis properties of GO silicon steel can be well reproduced. [ABSTRACT FROM AUTHOR]

Highly oriented W-type hexaferrites SrNi 2 Sc x Fe 16-x O 27 (SrW, x = 0.70, 0.75, 0.80 and 0.85) are fabricated via ceramic process and magnetic orientation to meet design requirements of self-biased circulators. The orientation degree reaches 0.81 when Sc3+ substitution content x is 0.75. The XRD refinement results in consideration of orientation illustrate the strong c -axis anisotropy texture of SrW. SEM images show significant uniformity in grain growth with c -axis stays vertical to sample plane. Consequently, the corresponding remanence ratio M r /M s reaches as high as 0.92, which is indispensable to reduce low field loss (LFL) as much as possible in the design of self-biased circulators. According to simulation results, the self-biased microstrip circulator based on this SrW material (x = 0.75) realizes ideal functions in circular transmission operating at Ku band. [ABSTRACT FROM AUTHOR]