Search

Interior permanent magnet synchronous machines (IPMSMs) driven with a square-wave control (i.e., six-step, block, or 120° control), known commonly as brushless direct current (BLDC) drives, are used widely due to their high power density and control simplicity. The advance firing (AF) angle is employed to achieve improved operation characteristics of the drive. The AF angle is, in general, applied to compensate for the commutation effects. In the case of an IPMSM, the AF angle can also be adjusted to exploit reluctance torque. In this paper, a detailed study was performed to understand its effect on the drive's performance in regard to reluctance torque. Furthermore, a multi-objective optimization of the machine's cross-section using neural network models was conducted to enhance performance at a constant AF angle. The reference and improved machine designs were evaluated in a system-level simulation, where the impact was considered of the commutation of currents. A significant improvement in the machine performance was achieved after optimizing the geometry and implementing a fixed AF angle of 10°. [ABSTRACT FROM AUTHOR]

Five‐phase permanent magnet synchronous machine (PMSM) can operate under open‐circuit faults with the appropriate current regulations. However, the traditional current regulations based on the five‐phase half‐bridge inverter have to satisfy the constraint of zero neutral point current, which limits the fault‐tolerant performance of the machine. Thus, this paper investigates the current regulation based on the five‐phase six‐leg (FPSL) inverter, which relieves the zero‐neutral point current limitation, and both current regulations considering the maximum torque (MT) and minimum copper loss (MC) are derived under different open‐circuit conditions. The cost of the system has increased, but with the new regulations, better fault‐tolerant operation capability of the machine can be obtained under all kinds of open‐circuit faults. Moreover, with the introduction of the neutral point current, the machine can work under triple‐phase open‐circuit faults. In conclusion, the proposed control scheme based on the FPSL inverter expands the fault‐tolerant operation capability of the five‐phase PMSM. The experiment results prove the effectiveness of the proposed current regulation on increasing average torque or reducing copper loss under fault‐tolerant operation. [ABSTRACT FROM AUTHOR]

PM enable PMSMs to have higher torque-density and power-density, however the machine performance is closely related to its load characteristics. When the armature excitation does not match the load characteristics of the PM and machine, it can lead to demagnetization and performance degradation. By comparing and studying the IPMSM's and SPMSM's load characteristics, a more reasonable machine topology of components such as PM can be obtained, and high-performance machines can be designed more efficiently. Based on the material characteristics of the PM, the armature reaction law of different machines and the demagnetization law of the PM at different current angles were analyzed. There are different magnetic field distribution patterns in IPMSM and SPMSM, and their different load characteristics are compared to study the methods for improving the anti-demagnetization ability of PMs based on different machine structures. [ABSTRACT FROM AUTHOR]

This paper presents research on an unconventional electric machine. It is a hybrid excited machine which includes the features of three types of machines: the Permanent Magnet Synchronous Machine, the Synchronous Machine, and the Synchronous Reluctance Machine. Therefore, a broad literature review related to the above-mentioned types of machines was constructed. The well-known Permanent Magnet assisted Synchronous Reluctance Machine joins features of Permanent Magnet Synchronous Machine and Synchronous Reluctance Machine topologies. This paper shows the results of the innovative design of the Hybrid Excited Permanent Magnet assisted Synchronous Reluctance Machine, which additionally has advantages of the Synchronous Machine. In the article the basic methods of electromagnetic flux control and the designs using them are also presented. Finally, the results of simulation studies of the effect of the stator skew on the machine performance are described. [ABSTRACT FROM AUTHOR]

Based on the magnetic gear effect, the field-modulated permanent-magnet machine (FMPMM) can realize the unequal pole design of the rotor PM field and the stator armature magnetic field. With the advantages of high torque density and high efficiency, the FMPMM has been widely studied in low-speed direct-drive applications. As a kind of machine excited by PMs, the performance of the FMPMM was affected by the demagnetization state. However, the method for establishing the FMPMM demagnetization model based on a finite element analysis (FEA) presented some problems, including tedious repeated modeling work and long calculation time-consuming under fine subdivision. Therefore, in this paper, a six-phase surface-mounted FMPMM was taken as an example, and an equivalent magnetic network (EMN) model was proposed for evaluating the machine performance under demagnetization. In order to realize the rapid establishing EMN models under diverse demagnetization types, the variable coercivity of PM was introduced. Furthermore, for the purpose of improving the calculation accuracy and shortening the calculation time, the least square method was used in fitting and analyzing the discrete results. Then, in order to verify the validity of the proposed EMN model, a prototype was fabricated and a testing platform was built. The air-gap flux density and the no-load back EMF obtained by the FEA, the proposed EMN model, and the experimental testing were compared. The results showed that the proposed EMN model can realize the rapid modeling and accurate analysis of the six-phase surface-mounted FMPMM under diverse demagnetization types. [ABSTRACT FROM AUTHOR]

To increase the airgap flux density, this paper proposes a new magnetic-field-modulated permanent magnet (FMPM) machine. The proposed FMPM machine has the compound magnets in the rotor, which is composited by the spoke PMs (SPM) and Halbach PMs (HPM). The proposed SH-FMPM machine facilitates better use of space for armature winding and PMs and combines the benefits of high torque density and high torque/loss. The formation process, operation principle, and electromagnetic performance of the SH-FMPM machine are introduced. It is demonstrated that the SH-FMPM machine has the high torque density and low torque ripple compared to the S-FMPM machine and the H-FMPM machine. [ABSTRACT FROM AUTHOR]

Consuming energy sources and greenhouse gas emission are one of the most prominent problems of the latest century. Most of the energy consumed globally and carbon dioxide emissions originate from electric motors used in the industry. Therefore, researchers have recently focused on the production of highly efficient, eco-friendly, and low-priced machines: Synchronous Reluctance Machines. In this study, the design and comprehensive Finite Element Analysis of a TLA-SynRM including the effects of the number of conductors per slot and wire diameter directly affecting stator slot fill factor and crucial for obtaining more realistic results from experiments has been initially carried out. Moreover, power factor, saliency ratio, and efficiency of the novel SynRM are enhanced by utilizing a fine-tuning process based on d- and q-axes flux paths. Additionally, the layer structure of the initial design is changed to a double-layer structure to improve the performance of the machine in the fine-tuning process. In the final step of this study, the machine has been manufactured, and experiments have been accomplished. This study has concluded that the novel SynRM have low torque ripple, high power factor, saliency ratio, and efficiency, whose value is within the range of IE5 efficiency class. [ABSTRACT FROM AUTHOR]

The interior permanent magnet synchronous machine (IPMSM) has been widely used in industrial applications due to its several favorable advantages. To further improve the machine performance, an improved nonlinear predictive controller for the IPMSM is proposed. In this paper, the maximum torque per ampere control law is firstly transformed to a linear function, according to the first−order Taylor expansion, and integrated with the control strategy. On this basis, an improved predictive control method is formulated by designing an optimized cost function through the input−output feedback linearization. Then the integral action is introduced to eliminate the influence of the load mutation and improve the steady−state control precision of the system. The stability of the control method is ensured by compelling the outputs to track the desired references without steady−state error. Finally, the simulation was established to verify the effective of the improved control method. Simulation results showed that the machine can reach the given reference speed without steady−state error within a short process, which means the machine has excellent dynamic and static performances. Furthermore, the machine has higher torque−to−current ratio by making full use of the reluctance torque. The simulation results verify the effectiveness of the improved control strategy. [ABSTRACT FROM AUTHOR]

This paper investigates magnet demagnetization characteristics of the modular permanent magnet machine. The influence of flux gaps on magnet flux density, losses distribution, torque and demagnetization are analyzed for different operating conditions. The magnet demagnetizations caused by three sources, such as the PM field, the armature field, and the magnet temperature rise, are individually investigated using the frozen permeability method. Furthermore, coupled electromagnetic (EM)-thermal modelling is also adopted in this paper to fully reveal the advantages of the modular machine in improving machine EM performances. This is essential due to the temperature-dependent properties of the machines, such as the magnet remanence, coercivity, and copper resistivity. For comparison propose, the EM performances with a particular focus on the demagnetization withstand capability for both the modular and non-modular machines are investigated based on the EM-thermal coupling. It is found that, compared to the non-modular machine, the modular machine can achieve higher torque, higher efficiency, and better demagnetization withstand capability. [ABSTRACT FROM AUTHOR]

In this article, we propose an unconventional method, i.e., generalized finite difference method (GFDM), to analyze the electromagnetic performance of surface-mounted permanent magnet (SPM) machine with eccentric rotor shape. The remarkable characteristic of this method is that it is meshless. In this method, the solution region is discretized in the form of nodes, and the nodes can move with the moving structure. This is very helpful in modeling the SPM machine because there is no remeshing process during the rotation. However, mesh generation is required in the traditional finite-element analysis (FEA). First, the basic principle of the proposed GFDM is introduced. Second, the whole field domain is divided into five types of regions, viz., PMs, air gap, slot openings, slots, and stator core. Third, the differential equations satisfied by each region are discretized into algebraic equations by the GFDM. The interfaces need to be dealt with separately because of the discontinuity of the derivative of the vector potential. Then, the systems of equations are solved to analyze the electromagnetic performance of an SPM machine. Finally, this method is implemented on a 12-slot, 10-pole SPM machine. Meanwhile, the effectiveness of this method is verified by an FEA and experiment. [ABSTRACT FROM AUTHOR]

In the high-speed flux-switching permanent magnet (FSPM) machine, the ac copper loss issue in the armature winding conductor is very prominent, due to the high-frequency leakage magnetic field in stator slot, which seriously affects the machine performance. To model and calculate ac copper loss more accurately, a coupled electric circuit-magnetic field model is constructed based on 2D-finite element method, and consequently the influence of modeling methods and winding types on ac copper loss calculation of a 12-slot/10-pole (12/10) 54.7 kW/10 kr/min FSPM machine is investigated. First, ten simplified ac copper loss calculation models are established to deal with the problem of large consumption of calculation time and computer resources caused by the excessive number of wires, small size of winding conductors, high precision modeling, and mesh refinement. Second, the influences of voltage-/current-source and steady/rotating rotor are considered, and the ten models are evaluated in terms of computing time and accuracy. Third, based on the preferred model from the ten models, the effects of frequency, round/flat wires, and wire sizes on ac copper loss are further studied. Fourth, to investigate the influence of flux leakage at the end of winding on ac copper loss, a 3-D ac copper loss calculation model with different axial lengths of winding end space is established. Fifth, the change process of ac copper loss and transient temperature of winding under short time overload condition are obtained combined with the bidirectional coupling model between electromagnetic and thermal field method through multiple iterations of electromagnetic loss and temperature. Finally, the stator modules of round and flat copper wires are manufactured, respectively, and an experimental modular device is built to measure the ac copper loss, which confirms the improved accuracy of the predictions by the proposed model. [ABSTRACT FROM AUTHOR]

Permanent magnet synchronous machines (PMSMs) have garnered increasing interest because of their advantages such as high efficiency, high power density, wide speed range, and fast dynamics. They have been employed recently in several industrial applications including robotics and electric vehicles (EVs). However, PMSMs have highly nonlinear magnetic characteristics, especially interior PMSMs, due to the existence of reluctance torque. Nonlinearity complicates not only machine modeling but also control algorithms. An accurate machine model is the key aspect for the prediction of machine performance as well as the development of a high-performance control algorithm. Hence, this paper presents an accurate modelling method for PMSMs. The proposed model method is applicable for all PMSMs, even multiphase machines. This paper considers a fractional slot concentrated winding 12/10 interior PMSM (IPMSM) for this study to demonstrate the effect of magnetic saturation and special harmonics. The developed model considers accurately the magnetic saturation, mutual coupling, spatial harmonics, and iron loss effects. It utilizes finite element analysis (FEA) to estimate the precise magnetic characteristics of IPMSM. The finite element model is calibrated precisely using experimental measurements. The iron losses are estimated within the simulation model as d- and q-axes current components. The model accuracy is validated experimentally based on a 12/10 IPMSM prototype. [ABSTRACT FROM AUTHOR]

This paper suggests a method to improve the performances of the Dual Stator Axial Flux Spoke-type Permanent Magnet (DSAFSPM) machines with phase group concentrated coil (PGCC) windings, by incorporating continuous and discrete step-skewing along with a special winding connection. The purpose of the study is to mitigate the cogging torque and torque ripples while increasing the output torque so it ameliorates the machine performance at minimum cost for various applications such as wind power plants and electric vehicles (EVs). Cogging torque produces noise and vibrations which degrade the machine's performance and reduces its life span. The proposed winding sequence enhances the output torque by improving its distribution factor along with the use of continuous skew and step-skew magnets. This research work improved the cogging torque and torque ripples with the help of skew techniques while output torque is increased by the proposed winding sequence. Further harmonics and ripples are also mitigated by the proposed winding sequence. The overall machine volume is kept constant along with the magnet size and the design parameters for fair performance analysis. Comparative analysis of these machines is performed using three-dimensional (3-D) time-stepped finite element analysis (FEA). Proposed model I and proposed model II reduce the harmonics by 42% and 23%, respectively. By using continuous skew and discrete step-skew magnets, cogging torque is reduced up to 81.5% and 75%, respectively. This reduction in cogging torque reduces the noise and vibration in machines which assists the machines to perform a smooth operation. The reduction in output torque ripples in proposed model I is 60.8% while that of proposed model II is 59.3%. [ABSTRACT FROM AUTHOR]

In this article, an axial-flux permanent-magnet (PM) Vernier machine with the triple-stator, spoke-type PM rotor, and toroidal winding wound on the innerstator is proposed. Benefited from the flux focusing spoke-type PM rotor and short end length toroidal winding, the proposed machine has a high torque density and the improved power factor. Based on the air-gap permeance function, the analytical expression of the proposed machine is derived to qualitatively analyze the machine's performance. The quasi-three-dimensional (3-D) finite element analysis (FEA) is adopted to optimize the design parameters, such as innerstator diameter, PM thickness, and slot opening width. The quasi-3-D FEA results match well with the 3-D FEA. The 3-D FEA results show the torque densities of the proposed machine reach 49.4 Nm/L and 11.4 Nm/kg, respectively, under the 232 A/cm average electrical loading. The performances, such as overload capacity, PM demagnetization, and PM and core losses, are also analyzed by 3-D FEA. The comparison with the other axial-flux PM Vernier machine is conducted, and the results reveal that the proposed machine has the great advantages of the torque density and power factor. Since the prototype is not built, in this article, the assembly scheme and thermal behavior of the proposed machine are discussed. [ABSTRACT FROM AUTHOR]

A 60-slot/22-pole five-phase machine with hybrid single-/double-layer fractional slot winding is proposed to improve torque under third harmonic current injection condition. Design process of the proposed machine includes two steps of first combining two sets of 20-slot/22-pole machine windings and then shortening coil-pitch. Due to the special structure of the proposed machine, torque-contributing space harmonics in magnetomotive force (MMF) are improved, and redundant space harmonic in MMF which causes high eddy current loss in permanent magnets is suppressed. The proposed machine is evaluated under two modes of third harmonic current injection, namely constant rms and peak harmonic injection. Compared with 20-slot/22-pole machine, the proposed machine achieves higher torque and lower losses under both third harmonic current injection conditions. Besides, the performance of the proposed machine when injecting only the first or third harmonic current is also analyzed. [ABSTRACT FROM AUTHOR]

In this article, slot-PM-assisted consequent-pole-PM machine (SPMA-CPMM) is proposed. The key is that the consequent-pole ferrite PMs are employed in the stator yoke to reduce the PM material cost largely, while a small amount of tangential magnetized rare-earth PMs is placed in the slot opening to improve the torque production. This proposed hybrid magnet design can greatly enhance the PM utilization ratio and reduce the PM cost while maintaining a relatively large torque density. In this article, the configurations of ferrite-PM machine (FPMM), consequent-pole ferrite-PM machine (CFPMM), and SPMA-CPMM are illustrated, while equivalent magnetic circuits (EMCs) of them are compared. Then, the electromagnetic performances of three machines are investigated and compared, which verifies the validity of the proposed machine. [ABSTRACT FROM AUTHOR]

For this paper, the possibility of using grain-oriented electric steel for the stator lamination in a double rotor fractional-slot concentrated-wound permanent magnet synchronous motor it was studied using FEM simulations. The results were compared with the ones of the non-oriented electric steel machine having two different stator lamination topologies. The purpose of this study was to estimate the influence of the stator yoke discharge for the proposed structure and to check the possibility of compensating some of its negative effects by using grain-oriented electric steel for stator lamination. The proposed solution gives the advantage of a modular construction of the stator lamination which simplifies the fabrication technology and reduces the production costs, at the same time, without major impact over the machines performances. [ABSTRACT FROM AUTHOR]

In high performance electric machines, the increase of fundamental frequency leads to additional losses in the winding due to parasitic effects such as the associated skin and proximity effects. In the first part, this paper presents an investigation into accurate modelling of AC losses in the winding using numerical methods and their experimental verification. Then, using experimental motorette setups, this research provides a comparative study between fixed strand positioning and fixed conductor shapes on the AC losses in the winding. It is shown that the exact position of strands in the conductor is not a critical factor; however, it is very important to control the conductor shape inside the slot. In the final section of this paper, an investigation into the relationship between AC losses in the winding and copper filling factor is presented. It is shown experimentally that counter-intuitive design choices such as using a lower copper fill factor and thicker strand diameters may be beneficial in achieving the highest overall efficiency. [ABSTRACT FROM AUTHOR]

For this paper, the possibility of using grain-oriented electric steel for the stator lamination in a double rotor fractional-slot concentrated-wound permanent magnet synchronous motor it was studied using FEM simulations. The results were compared with the ones of the non-oriented electric steel machine having two different stator lamination topologies. The purpose of this study was to estimate the influence of the stator yoke discharge for the proposed structure and to check the possibility of compensating some of its negative effects by using grain-oriented electric steel for stator lamination. The proposed solution gives the advantage of a modular construction of the stator lamination which simplifies the fabrication technology and reduces the production costs, at the same time, without major impact over the machines performances. [ABSTRACT FROM AUTHOR]

Linear alternators work seamlessly with Free-Piston Stirling Engines (FPSE) in the energy conversion process. This research concentrates on the design and development of a tubular slot-spaced Permanent Magnet Linear Alternator (PMLA) to be coupled with the FPSE. In an attempt to increase the power density of the machine over conventional PMLAs, a slot space is added to reduce the total mass of the stator and a parametrical study is carried out for the same. Numerically analyzing the fundamental parameters such as change of stator and magnet materials, and operating conditions frequency and stroke length. The effects of slotting are studied to understand the skinning effects on the tooth and the performance variation of the machine. A modified model is obtained to surpass 100 W from the numerical analysis of the parametric variations. Putting the machine to extreme limitations, the study conducted upon variations of parameters obtained a stable maximum power density of 186 W/kg and produced a power of 921 W for the designed PMLA. The study outlines the variation seen in the performance of the machine in such diverse conditions they go through during their life cycle. [ABSTRACT FROM AUTHOR]

It is well known that permanent magnet Vernier machine (PMVM) has multiple flux field harmonics, which can produce stable torque. However, some flux field harmonics would create torque that undermines the total torque output. Such as the 6 slots 26 poles split-tooth PMVM here, of which modulated flux field outputs torque while fundamental flux field undermines torque output. In this article, a 26 pole PMVM with coding-shaped tooth is proposed. The coding-shaped tooth can introduce permeance harmonics with specific phase and amplitude, thus modulating flux fields that all output torque. Air-gap permeance harmonics of the proposed and the regular split-tooth PMVM are obtained via FEA. Based on MMF-permeance model, flux fields of two machines and their contributions to average torque are investigated, proving that the proposed machine has multiple flux fields that all output torque. Moreover, by optimizing geometric parameters of coding-shaped tooth, the proposed machine could obtain largest average torque and smallest torque ripple simultaneously. Electromagnetic performances of the optimized machines are studied comparatively in semianalytical way and FEA. It is proved that with same overall size, PM usage, and copper loss, the proposed machine could achieve 30% larger torque density, 86% smaller cogging torque, and 62% lower torque ripple than its counterpart. Finally, a 16-N·m (rated) prototype is built and tested. [ABSTRACT FROM AUTHOR]

This paper develops a new model with adjustable accuracy to evaluate performance of permanent magnet Vernier machine (PMVM) based on flexible magnetic equivalent circuit (MEC) method. The desired machine parameters such as number of flux modulation poles (FMPs), winding pole‐pairs, and geometrical dimensions can be chosen in the presented model. By utilizing nonlinear core magnetization curve, saturation effect is taken into account. There are two main contributions in this study. First, the flexible MEC model is developed to predict the machine performance accurately. The second contribution is that the developed model can be used to evaluate the performance of the machine under no‐load and loading conditions at the same time. The results of MEC model under no‐load and loading conditions are compared with 2D‐finite element method (FEM) and 3D‐FEM in terms of accuracy and simulation time. The results indicate acceptable accuracy and suitable processing time of the proposed MEC model. [ABSTRACT FROM AUTHOR]

In this study, a torque enhancement principle for a stator permanent-magnet (PM) Vernier machine with a consequent pole structure is proposed. The novelty of the manuscript is the explanation of how stator PM Vernier machines benefit from consequent pole structure. Although a similar concept of stator PM Vernier machines with a consequent pole structure has been investigated in previous studies, a clear torque enhancement principle was absent. The keys to torque enhancement are the decrement of nonworking harmonics and increment of working harmonics. To demonstrate these phenomena, the torque contributions from the harmonics were calculated. Subsequently, the performances of the conventional machine and consequent pole machine were compared to verify the enhancement principle. The electromagnetic performances, including the back electromotive force and torque, were compared. The results show that the stator PM Vernier machine benefits significantly from torque enhancement using the consequent pole structure, and the torque enhancement principle was verified. [ABSTRACT FROM AUTHOR]

This paper presents an improved magnetic equivalent circuit (MEC) method for modeling linear permanent-magnet synchronous motors (LPMSMs) with adjustable accuracy. The performance of machine with different dimensions, poles and slot numbers can be studied by the proposed flexible MEC, where the core nonlinearity is fitted on the material B–H curve. End effect is modeled by considering two virtual zones with desired accuracy at both entrance and exit ends of the primary. A new structure based on magnets segmentation is also proposed to investigate its effect on the motor performance. Finally, the results of the proposed method are compared with 3D-FEM to show the effectiveness of the presented model. The results show improvement in processing time with good accuracy compared to previous classic methods. In general, introducing a new model based on an improved MEC approach for modeling LPMSMs considering slot effect, iron core saturation and segmented PMs with flexible accuracy by adjusting the number of flux tubes is the paper novelty which is studied in this work. [ABSTRACT FROM AUTHOR]

This article presents a new rotor configuration for V-shaped interior permanent magnet machine to reduce torque ripple and electromagnetic vibration. The proposed rotor structure consists of two segments staggered mechanically 180°. In each segment, the intersection angle between two magnets of one V-shaped pole is different to the others, resulting in a different pole arc to pole pitch ratio. The dimensions and total volumes of magnets keep unchanged. Benefitting from the two opposing segments, unbalanced magnetic pull can be offset. Machine performances in terms of back-EMF, d-&q-axis inductance, radial and axial force and instantaneous torque ripple are intensively compared and evaluated to the conventional machine with skewing slots, which is often used in mass production. Comprehensive models using coupled multiphysic fields are established and the comparative study of electromagnetic vibration aspects are done. Two machines, i.e., the proposed machine and the conventional machine with slot skewing are prototyped. Extensive experiments are carried out and compared in terms of back-EMF, current, modal frequency, static average torque, instantaneous torque, and efficiency. [ABSTRACT FROM AUTHOR]

In this article, a robust optimization design method considering magnet material uncertainties is proposed for permanent magnet (PM) machines. The key of this method is to improve the machine design robustness to resist the uncertainties influence from PM material, including material diversity, manufacture error, and assembly accuracy. To verify the proposed optimization method, a double PM machine is selected as an example. During the implementation of optimization design, first, the robust optimization model is constructed based on the analysis of PM uncertainties. Then, the Kriging surrogate model and non-dominated sorting genetic algorithm II (NSGA-II) are adopted to solve the optimization model. Finally, to verify the effectiveness of the method, the machine performance and corresponding reliability are evaluated, and a prototype is manufactured and tested. Both simulation and experimental results indicate that the proposed robust optimization method can effectively reduce the influence of magnet material uncertainties on PM machine performance. [ABSTRACT FROM AUTHOR]

In this article, an improved surrogate-assisted design optimization method is proposed and applied to the torque performance optimization of a five-phase surface-mounted permanent magnet machine with quasi-trapezoidal permanent magnets. It integrates the Taguchi and surrogate-assisted methods; the training data for surrogate models are generated by the Taguchi method to reduce reliance on the finite-element analysis (FEA), in turn, the local optimum problem caused by the Taguchi method is tackled by the surrogate model. The generalization ability of surrogate models is enhanced by the parameter transfer technique. Using the fuzzy best-worst method, the decision process of multiple solutions is placed before optimization so that the multiobjective optimization can be transformed into a single objective to facilitate the search process for the optimal design. The optimization results are validated by the test results from a prototype. Compared with the FEA-based parametric scanning method, the optimization cycle is shortened by 94% and a globally optimal design can be obtained. [ABSTRACT FROM AUTHOR]

In this paper, superposition methods including the superposition of a single stator tooth and the superposition of a single rotor tooth, are proposed to predict the open-circuit performances of flux-reversal permanent magnet (FRPM) machines. By the proposed superposition methods, the electromagnetic performances, such as air-gap flux density, electromotive force, cogging torque, and unbalanced magnetic pull (UMP) are investigated and verified by 2D finite element analysis (FEA). Further, according to the superposition methods, cogging torque reduction techniques can be acquired from both stator side and rotor side. In addition, the influence of stator-slot/rotor-pole-pairs (slot/pole) combination on UMP is also studied, and consequently, a reasonable slot/pole combination rule is suggested to avoid UMP. Then, an improved configuration for UMP reduction is also investigated and verified by FEA. Finally, the prototype machines are manufactured and tested to further verify the theoretical analysis and FEA predictions. [ABSTRACT FROM AUTHOR]

Based on the electromagnetic-structural coupling analysis, this article proposes the comparative study of three double-stator interior- permanent magnet vernier (DS-IPMV) machines, including the spoke-PM, V-shape-PM (V-PM), and H-shape-PM (H-PM) rotor structures. DS cooperation strategies are adopted in the machine design for the performance improvement. Firstly, the rotor optimization of the proposed machines is carried out, with consideration of the tooth-slot cooperation between the rotor and stators. The electromagnetic- structural coupling-simulation is adopted for comprehensive evaluation. Then, the specific performance comparison is carried out, including the magnetic, structural and cost analysis. Consequently, the spoke-PMV machine accommodates the highest torque output, efficiency and cost-effectiveness; meanwhile, the V-PMV machine possesses the highest torque per PM volume with the better ripple performance. Accordingly, prototype experiments are carried out for the validation of the proposed machine design and comparison. [ABSTRACT FROM AUTHOR]

In this article, an optimization design method of power factor is proposed for vernier permanent magnet (VPM) machine, in which the key is to analyze and investigate the power factor from the perspective of air-gap flux harmonic modulation. To improve the design efficiency, air-gap harmonics are analyzed and serve as the crucial bridge between power factor and machine geometry. It is noted that, during the operation of the VPM machine, more attention is required for the power factor of low-speed operation area. Based on the popular new European driving cycle of the electric vehicles, three low-speed driving conditions are chosen for the optimization design. For the systematic investigation, a V-shape VPM machine is selected as an optimization example. In order to evaluate conveniently, the comprehensive power factor is defined and sensitive air-gap flux harmonics of different conditions are selected as the optimization objectives, for improving the power factor characteristics in low-speed conditions. In addition, power factor and machine performances are evaluated to validate the proposed method. Finally, the prototype machine is built and tested. Both the simulation and experimental results reveal the feasibility and effectiveness of the proposed method and investigated VPM machine. [ABSTRACT FROM AUTHOR]

In this article, the field modulation effect (FME) of consequent-pole permanent magnet (CPM) machine is revealed and investigated from the perspective of a double-side slotting effect (DSSE), which can characterize and elaborate its torque production mechanism. Since the CPM machine features that both PM and armature fields are modulated by stator /rotor teeth, which generates more field harmonics contributing to the torque production compared with conventional surface-mounted PM (SPM) machine. A simplified PM magneto-motive force (MMF)-permeance based model is first established to confirm the effective working harmonics of the CPM machine. The contributions of dominant air-gap field harmonics to the torque production are then demonstrated and quantified based on Maxwell stress tensor (MST) method. The impacts of FME on the torque performance of the CPM machines with different stator-slot/rotor pole combinations are subsequently investigated by the finite element (FE) method and compared with those of conventional SPM counterparts. Besides, the influences of rotor PM parameters on the FME of the CPM machine are also evaluated. Finally, the experimental measurements on a 12-slot/14-pole CPM machine prototype are carried out to validate the theoretical and FE analyses. [ABSTRACT FROM AUTHOR]

This article first proposes a generalized decomposition model for dual three-phase (3-ph) permanent magnet synchronous machines (PMSMs) with 0°, 30°, and 60° angle displacements between two sets of windings, allowing machines controlled in two-dimensional orthogonal αβ and xy subspaces. This model can decouple mutual inductances coupling phases from two sets, respectively. However, there often exist asymmetric impedances, due to inherent asymmetric machine parameters, cables with unequal lengths, manufacture tolerances, etc., in dual 3-ph PMSMs inevitably causing unbalanced phase currents and deteriorating the decoupling performance of the generalized machine model. Therefore, the generalized decomposition model incorporating asymmetric impedances is further developed, in which additional terms incurred by asymmetric impedances lead to the cross-coupling of αβ subspace and xy subspace. Through this model, the compensation capability of asymmetries is derived at a given dc link voltage. Then, a compensation strategy is illustrated to suppress unbalanced phase currents together with current harmonics caused by nonlinearities. Finally, experimental results testify the current balancing performance and simulation results further validate the machine model and the compensation capability. [ABSTRACT FROM AUTHOR]

Oriented steel has higher permeability and lower losses in the direction of orientation (the rolling direction) than non-oriented steel. However, in the transverse direction, oriented steel typically has lower permeability and higher losses. The strategic use of oriented steel in a modular Permanent Magnet Synchronous Machine (PMSM) stator can improve machine performance, particularly when compared to a machine designed with non-oriented steel, by increasing both torque and efficiency. Typically, steel manufacturers provide magnetic properties only in the rolling and transverse directions. Furthermore, in modern Finite Element Analysis (FEA) software, the magnetic properties between the rolling and transverse directions are interpolated using an intrinsic mathematical model. However, this interpolation method has proven to be inaccurate; to resolve this issue, an improved model was proposed in the literature. This model requires the magnetic properties of the oriented steel in between the rolling and transverse directions. Therefore, a procedure for extracting the magnetic properties of oriented steel is required. The objective of this work is to propose a method of determining the magnetic properties of oriented steel beyond just the oriented and transverse directions. In this method, flux-injecting probes, also known as sensors, are used to inject and control the flux density in an oriented steel segmented stator in order to extract the properties of the oriented steel. These extracted properties are then used to model an oriented steel modular stator PMSM. The machine's average torque and core losses are compared with conventional, non-modular, non-oriented steel stator PMSM, and modular, non-oriented steel stator PMSM. It is shown that both the average torque and the core loss of the oriented steel modular stator PMSM have better performance at the selected number of segments than either of the two non-oriented steel stators. [ABSTRACT FROM AUTHOR]

A new Single-sided Variable Flux Permanent Magnet Linear Machine with flux bridge in mover core is proposed in this paper. The flux bridge prevents the leakage flux from the mover and converts it into flux linkage, which greatly influences the performance of the machine. First, a lumped parameter model is used to find the suitable coil combination and no-load flux linkage of the proposed machine, which greatly reduces the computational time and drive storage. Secondly, the proposed machine replaces the expensive rare earth permanent magnets with ferrite magnets and provides improved flux controlling capability under variable excitation currents. Multivariable geometric optimization is utilized to optimize the leading design parameters like split ratio, stator pole width, width and height of permanent magnet, flux bridge width, the width of mover's tooth, and stator slot depth at constant electric and magnetic loading. The optimized design increases the flux linkage by 44.11%, average thrust force by 35%, thrust force density by 35.02%, minimizes ripples in thrust force by 23%, and detent force by 87.5%. Furthermore, the results obtained by 2D analysis are verified by 3D analysis. Thermal analysis is done to set the operating limit of the proposed machine. [ABSTRACT FROM AUTHOR]