Search

Screw pine root fibers are engineering fibers that have yet to be explored in terms of its chemistry with bio‐resin in biodegradable composites to replace nonbiodegradable thermoplastics used in packaging, automobiles, furniture, and industrial sectors. Screw pine root fibers are reinforced with soy, poly(vinyl alcohol), and soy‐poly(vinyl alcohol) resin systems in this work to create a variety of composites. Composites demonstrated highest amount of tensile strength at around 39.7 MPa, 37.6 MPa of flexural property, along with an impact strength around 12.4 kJ/m2. The thermal solidity of the optimized material was determined to be 235°C. After 24 hours of immersion, the composite had the lowest water absorption of 18.4%. All composites were shown to be biodegradable, losing about 54.2%–72.9% of their original mass after 60 days in soil burial. Unique characteristics such as the use of low‐cost agricultural materials, water‐based resin, stable composite, and properties such as moderately strong, safe disposal after service periods make these manufactured composites market feasible as consumer‐friendly/ecofriendly green products. Highlights: Screw pine root fibers were extracted from waste roots and used as reinforcement.The tensile strength of the composite was achieved as 39.7 MPa.The water absorption of hybrid composite was found 30.8% after 24 h.After 60 days under soil burial, composite lost 67.5% of its original weightDeveloped composites can be good alternant for nondegradable thermoplastic. [ABSTRACT FROM AUTHOR]

Cellulosic fibers obtained from Barley straw were utilized to reinforce PHB. Four different processed fibers were employed as reinforcing material: sawdust (SW), defibered (DFBF), delignified (DBF), and bleached (BBF) fibers. The composite was processed from two different perspectives: a discontinuous (bach) and an intensification process (extrusion). Once processed and transformed into final shape specimens, the materials were characterized by mechanical testing (tensile mode), scanning electron microscopy, and theoretical simulations by finite elements analysis (FEA). In terms of mechanical properties, only the elastic moduli (Et) exhibited results ranging from 37% to 170%, depending on the reinforcement composition. Conversely, strengths at break, under both tensile and bending tests, tended to decrease, indicating poor affinity between the components. Due to the mechanical treatment applied on the fiber, DFBF emerged as the most promising filler, with mechanical properties closest to those of neat PHB. DFBF-based composites were subsequently produced through process intensification using a twin-screw extruder, and molded into flowerpots. Mechanical results showed almost identical properties between the discontinuous and intensification processes. The suitability of the material for agriculture flowerpots was demonstrated through finite analysis simulation (FEA), which revealed that the maximum von Mises stresses (5.38 × 105 N/m2) and deformations (0.048 mm) were well below the limits of the composite materials. [ABSTRACT FROM AUTHOR]

Natural fibers are one of the most attractive materials in biocomposites due to their potential for sustainability. This study aims to prepare sustainable composite materials using fibers from Sansevieria trifasciata (snake plant) and to investigate their mechanical, morphological, and water absorption properties. The composite was prepared with epoxy resin through a manual hand lay‐up process, maintaining standard parameters with changeable reinforcement (10%, 20%, and 30%). The mechanical properties (tensile, impact, and flexural strength), Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), and water absorbency of the composites were evaluated. The result showed that the tensile strength, flexural strength, and impact resistance of the composites are 6.99 MPa, 10.77 MPa, and 14 J, respectively, for 30% fiber components, which are significantly higher than other composite materials. The SEM analysis showed a strong interfacial bond between the snake plant fiber and the epoxy resin. The FTIR analysis revealed a reduction in hemicellulose and lignin and an improvement in the interfacial adhesion between snake plant fiber and epoxy resin. The composites also demonstrated time‐dependent increases in water absorption, with the sample containing 30% fiber components showing the best absorbency performance at 0.88%. Highlights: A study is being conducted on the effective and sustainable use of biowaste.The composite materials loaded with 30% fibers had significantly high tensile strength, flexural strength, and impact resistance.The SEM analysis of snake plant fiber‐reinforced polymer composite showed a strong interfacial bond between fiber and epoxy resin.The FTIR analysis of the composite revealed the reduction of hemicellulose and lignin.The use of non‐renewable materials is reduced, and eco‐friendliness is promoted. [ABSTRACT FROM AUTHOR]

The present investigation seeks to assess the impact of fillers on the mechanical characteristics of entirely biodegradable composites, introducing an advanced solution to fulfil long-term durability demands within point-of-purchase (POP) industries. The inclusion of calcium carbonate (CaCO3) fillers on the various properties of the flax fibre-reinforced composites, after accelerated irradiation in an ultraviolet (UV) radiation exposure has been investigated in the present study. Different types of flax fibre-reinforced poly lactic acid (PLA) biocomposites (with and without filler) were fabricated. The mechanical (tensile and flexural), and physical properties of the specimens were assessed after 500 h of exposure to accelerated UV irradiation of 0.48 W/m2 at 50 °C and were compared with those of the unexposed specimens. The results indicate that the presence of the inorganic filler significantly improved the performance of the biocomposites compared to the unfilled biocomposites after UV exposure. After adding 20% of fillers, the tensile strength was increased by 2% after UV degradation, whereas the biocomposite without filler lost 18% of its strength after UV exposure. This can be attributed to the change in the photo-degradation of the PLA due to the presence of the CaCO3 filler, which acts as a safeguard against UV light penetration by creating a protective barrier. The scanning electron microscopy (SEM) images of the degraded specimen surface show substantial difference in the surface topography of the composites with and without fillers. [ABSTRACT FROM AUTHOR]

This research work investigates the effects of the concentration and treatment of chopped false banana (Ensete ventricosum) fibres on the mechanical properties of a polypropylene matrix. The chopped false banana fibres (FBFs) were modified using Aloe Vera gel following treatment with 5% NaOH for 12 h at room temperature, with 1% acetic acid used to neutralise the remaining NaOH. FBF-reinforced polypropylene composite plates were then manufactured with 10, 20, 30, and 40 wt.% of chopped FBF. The mechanical properties were investigated using the compressive, impact, and three-point bending tests. Regarding the mechanical properties of the FBF-reinforced polypropylene composites, it was found that they have a maximum average compressive strength of 17.2 MPa. A maximum bending strength of 12.109 MPa was found for the Aloe Vera gel-treated composite with 30 wt.% of FBF. The maximum average compressive strength for this composite was 17.19 MPa. A maximum bending strength of 9.97 MPa for untreated composites was recorded for the composite with 10 wt.% of FBF. Finally, Aloe Vera-treated FBF-reinforced composites have better mechanical properties than untreated ones. The mechanical properties of Aloe Vera-treated FBF-reinforced polypropylene composites, as determined via impact, compressive and flexural tests, were superior for composites with 30 wt.% of FBF. [ABSTRACT FROM AUTHOR]

This work highlights the exploitation of fibers from a promising plant, commonly called Diss, in polymer matrix reinforcement. In this context, various untreated and treated (with acetic acid, silane, NaOH, thermal) Diss fibers were used to reinforce a thermoplastic matrix, polypropylene (PP). The effect of fiber treatments was evaluated at a ratio of 10% (by mass) of fiber, using mechanical, microstructural and physical characterization. A fiber content optimization study was carried out after choosing the fiber treatment by varying the fiber content from 10% to 40%. The microstructure observations showed a multi-layer structure for the biocomposites studied. The particular morphology of Diss fibers, with the presence of thorns, seems to improve the mechanical adhesion between the two phases. For 10% fiber content composites, the incorporation of the different fibers in the PP matrix led to improvements in most mechanical properties. The biocomposite reinforced with NaOH treated fibers (NPP-10%) showed the best mechanical performance with an improvement of 30%, 22% and 9% in tensile modulus, bending modulus and bending stress, respectively. For the fiber content variation, the NPP was retained, and an enhancement in the tensile modulus was found when the fiber content was below 20%. [ABSTRACT FROM AUTHOR]

Fiber-reinforced green composites made from natural plant fibers are an increasingly popular sustainable alternative to conventional high-performance composite materials. Given the variety of natural fibers themselves, and the even larger variety of possible composites with specific fiber dosage, fiber orientation distribution, fiber length distribution, and fiber–matrix bond characteristics, micromechanics-based modeling is essential for characterizing the macroscopic response of these composites. Herein, an analytical multiscale micromechanics model for elastic homogenization is developed, capable of capturing the variety. The model features (i) a nanoscopic representation of the natural fibers to predict the fiber stiffness from the universal stiffness of the fiber constituents, mainly cellulose, (ii) a spring-interface model to quantify the compliance of the fiber–matrix bond, and (iii) the ability to model any (and any combination of) orientation distribution and aspect ratio distribution. Validation is performed by comparing the predicted stiffness to experimental results for as many as 73 composites available in the literature. Extensive sensitivity analyses quantify the composite stiffening upon increasing fiber volume fraction, fiber alignment, fiber length, and fiber–matrix interface stiffness, respectively. [ABSTRACT FROM AUTHOR]

Paunch is a fibrous solid residue consisting of partially digested feed from the stomachs of processed cattle. It is the largest untapped solid waste stream from animals at meat processing plants, and potentially a valuable source of fibres for the production of sustainable and potentially higher-value natural biocomposite materials. Paunch was obtained from the waste effluent of a red meat processing plant, and the fibre characteristics of the as-obtained material were studied and benchmarked against wood flour and ground buffel grass, with a view to evaluating the potential of paunch as a fibre for polymer composites. The ground paunch possessed a rough fibrous surface and fibre-like characteristics that were comparable to both wood flour and ground buffel grass, demonstrating their potential for use in composites. Without any pre-treatment or compatibilisation, composites of a representative biopolymer, poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and ground paunch were successfully produced for the first time via extrusion, with up to 50 wt% paunch content. Mechanical property analysis showed that, at 30 wt% content, PHBV/ground paunch composites yielded mechanical properties that were comparable to those of composites with ground buffel grass. [ABSTRACT FROM AUTHOR]

Natural fibers such as jute, cotton, and bamboo composites are becoming alternative materials to synthetic fiber composites, as their use raises awareness of environmental protection. Among natural fibers, jute and cotton fibers were used in this research to fabricate six-layered composites reinforced by spent tea leaves. Varying amounts (0, 5, 10, and 15 g) of spent tea leaf powder were incorporated as reinforcement with resin to improve and observe properties and determine usability. The prepared composites were investigated comparatively in terms of mechanical, microstructural, morphological, and thermal properties. As regards mechanical characterization, tensile, compression, and bending properties were tested in this research to compare the obtained data with the data available in the literature to show its practical application. The results indicated that significant improvements in mechanical properties were obtained from the composites up to a certain proportion of reinforcement. The addition of 10 g reinforcement of spent tea leaves improved tensile strength by 33.46% and compressive strength by 38.86%. In terms of microstructural, morphological, and thermal characterization, in-depth SEM, EDS, XRD, UV, FTIR, TGA, and DSC analyses were performed. The results revealed that advanced microstructural, morphological, and thermal properties were improved with a certain proportion of spent tea leaf reinforcement. [ABSTRACT FROM AUTHOR]

[Display omitted] • A novel inverse biological crossed-lamellar structure was synthesized in CFRP. • This is the first non-biological prototype crossed-lamellar structure in the literature. • The tailored inverse-biologic crossed-lamellar structure is designed to achieve higher load-carrying capacity and stiffness. The remarkable toughness of Strombus gigas shell arises from its microstructure. In this study, inspired by the biologic crossed-lamellar microstructure of Strombus gigas shell, we prepared a novel carbon fiber reinforced polymer (CFRP) composite with inverse-biologic crossed-lamellar structure by replacing the inner and outer layers with the "tough" middle structure. The influences of the alternating arrangement of crossed-lamellar three-layer structure on the mechanical responses, including toughening mechanisms and biological mechanism, were studied. Experimental and numerical results indicated that as burrowing mollusks, Strombus gigas shells require a balance of certain load-carrying capacity and stronger protection function. Meanwhile, the tailored inverse-biologic structure achieved higher load-bearing capacity and stiffness. Additionally, the Bouligand-ply design strategy was proposed as an alternative to the traditional angle-ply design for the crossed-lamellar structure. By changing the laying-up form and pitch angle of the middle layer, a significant improvement in both load-bearing and energy dissipation capacity of the structures was achieved. The paper provides valuable insights for the design of high-performance biomimetic crossed-lamellar structures and holds great potential for the customization of fiber-reinforced composites. [ABSTRACT FROM AUTHOR]

We analyzed the problematic textile fiber waste as potential precursor material to produce multilayer cotton fiber biocomposite. The properties of the products were better than the current dry bearing type particleboards and ordinary dry medium-density fiberboard in terms of the static bending strength (67.86 MPa), internal bonding strength (1.52 MPa) and water expansion rate (9.57%). The three-layer, four-layer and five-layer waste cotton fiber composite (WCFC) were tried in the experiment, the mechanical properties of the three-layer WCFC are insufficient, the five-layer WCFC is too thick and the four-layer WCFC had the best comprehensive performance. The cross-section morphology of the four-layer WCFC shows a dense structure with a high number of adhesives attached to the fiber. The hardness and stiffness of the four-layer cotton fiber composite enhanced by the high crystallinity of cellulose content, and several chemical bondings were presence in the composites. Minimum mass loss (30%) and thermal weight loss rate (0.70%/°C) was found for the four-layer WCFC. Overall, our findings suggested that the use of waste cotton fiber (WCF) to prepare biocomposite with desirable physical and chemical properties is feasible, and which can potentially be used as building material, furniture and automotive applications. • We study the potential use of waste cotton fiber in different-layer composites. • We used water, hot pressing and epoxy adhesives to fabricate the novel composite. • Cell wall collapses and chemical bonds enhanced the mechanical bonding. • It showed better mechanical properties compared to existing medium density boards. • Four-layer waste cotton fiber composite are the best preparation process. [ABSTRACT FROM AUTHOR]

Biodegradable fiber-reinforced biocomposites from steam-exploded coconut fibers and polylactic acid (PLA) and polybutylene succinate (PBS) plastic were developed in this study. Biocomposite filaments and samples were produced using a commercial-scale screw extruder and a 3D printer, respectively. In-depth mechanical and thermal analyses were also performed. The results showed that the tensile strengths of PLA mixed with 3% coconut fiber (PLA97/F3) and 6% coconut fiber (PLA94/F6) decreased by approximately 22% and 23%, respectively, compared to the 64% reduction of that of the original PLA after four-week storage. The bending modulus of the PLA/fiber composite was better than that of the original PLA (21–29% higher), whereas a 5–8% improvement was observed for the PLA/PBS/fiber composites. The impact strengths of PLA97/F3 and PLA77/PBS20/F3 were approximately 8.5% and 7.4% higher than those of the original PLA and PLA/PBS, respectively. During the degradation test, both PLA97/F3 and PLA77/PBS20/F3 exhibited higher tensile strengths than the original materials. Finally, this research presents encouraging results for the production of biodegradable fiber-reinforced biocomposites that are applicable to 3D printing platforms. The final products can be used as replacement or aftermarket components of automobiles. • PLA, PBS, and steam-exploded coconut fiber were used for filament production. • The 3D-printed biocomposites were subjected to mechanical and thermal tests. • Coconut fiber is effective as a natural fiber reinforcement material. • The products have higher tensile strengths than original materials during degradation test. [ABSTRACT FROM AUTHOR]