Search

This paper presents the results of field tests performed to investigate the installation effects of pre-bored grouted planted (PGP) pile in deep clayey soil. The variation of horizontal soil displacements, excess pore water pressures and lateral soil pressures was measured in the PGP pile installation process. The test results show that the drilling and grouting process induced large horizontal soil displacements in the soil within a radial distance of 2 d (d is pile diameter), and the maximum horizontal soil displacements induced by the drilling and grouting process were smaller than 15.9 mm when the radial distance reached 4–5 d. Moreover, the horizontal soil displacements decreased along the soil layer depth, as the superficial soil layers were of small deformation modulus and lateral soil pressure. The drilling process brought large excess pore water pressures in the soil when the radial distance was less than 3 d, and the excess pore water pressures induced by the drilling stage were all less than 55 kPa when the radial distance reached 4–6 d. The drilling process also induced some lateral soil pressure increases in the soil within a radial distance of 3 d, while the measured maximum lateral soil pressure increases were smaller than 10.9 kPa when the radial distance increased to 4 d. On the whole, the excess pore water pressures and lateral soil pressure increases induced by the installation of PGP pile were much smaller than that induced by the installation of driven PHC pile. Moreover, the horizontal soil displacements, excess pore water pressures and lateral soil pressure increases induced by the installation of PGP pile all recovered rapidly after the installation of pile, as the cemented soil in the pile hole was in liquid state after the drilling and grouting stage. [ABSTRACT FROM AUTHOR]

This paper analyzes the bearing capacity of two-layered soil medium using finite element (FE) software ABAQUS/CAE 2023. Although geotechnical engineers design foundations for layered soil, majorly current geotechnical studies emphasize single homogenous soil. So, this research has significant novelty as it focuses on layered soil and adds to the current literature. A nonlinear FE model was prepared and analyzed to determine the ultimate bearing capacity of two-layered soil (sandy soil over clayey soil). The Drucker–Prager and Mohr–Coulomb models were used to represent sandy soil and clayey soil layers, respectively. Strip footing material properties were considered isotropic and linearly elastic. This study performed parametric studies to understand the effects of thickness, unit weight, and the modulus of the elasticity of sandy soil on the ultimate soil bearing capacity. Additionally, it also analyzed the effect of the cohesive strength of clayey soil on layered soil bearing capacity. Results showed that an increase in sandy soil layer thickness strengthens the layered soil, and thus, improves the bearing capacity of soil. Increasing the sandy soil layer thickness over footing width (h1/B) ratio from 0.15 to 2.0 improved the ultimate bearing capacities with elastic settlements of 350 mm and 250 mm by 145.62% and 101.66%, respectively. Additionally, for a thicker sandy soil layer, an increase in the unit weight and modulus of the elasticity of sandy soil led to higher ultimate bearing capacity. Furthermore, it was concluded that an increase in clayey soil's cohesive strength from 20 kPa to 30 kPa resulted in a 24.31% and 3.47% increase in soil bearing capacity for h1/B = 0.15 and h1/B = 2.0, respectively. So, the effect of cohesion is prevalent in the case of a thicker clayey soil layer. [ABSTRACT FROM AUTHOR]

The theoretical and practical studies of the cyclic loads resulting from the movement and passage of trains on the unsaturated subgrade to determine the effect of the degree of saturation and moisture content on the foundations and infrastructure of the railway lines, especially the settlement in the railway lines as a result of the development of the train loads. Thirty-six laboratory experiments were carried out using models that simulate a railway with nearly half the scale of the real one, using an iron box of (1.5 × 1.0 × 1.0) meters and a layer of clay soil with a thickness of 0.5 m representing the base layer, were constructed inside it. Above it, there is a layer of crushed stone representing a 0.2 m thick ballast, topped by a rail line of 0.8 m long installed on three sleeper beams with dimensions of 0.9 m (0.1 × 0.1 m). The subgrade layer has been constructed at different saturation degrees as follows: 100, 80, 70, and 60%. The tests were carried out using different load amplitudes and frequencies. These experiments investigated the effect of the subgrade degree of saturation on the value of the stresses generated on the surface and the middle (vertical and lateral stresses) and the settlement of the subgrade. In the case of unsaturated subgrade soil, an increase in load frequency has a clear effect on increasing the generated stresses in the subgrade layer, especially with lower saturation levels. However, the results and measurements of these experiments found that the load frequency almost had no effect on the values of the stresses generated on the surface and inside the subgrade layer with a 100% degree of saturation. The results of the investigation demonstrated that, while load frequency had a minimal effect on track-panel settlement, it increased with the load amplitude and subgrade soil saturation degree. The change of settlement of the track panel with the number of cycles has a high rate at the beginning; after a while from that, it decreases gradually until, after some value of the number of cycles, the settlement changes at a very low rate and gradually. [ABSTRACT FROM AUTHOR]

Climate change and irresponsible urbanization practices are anticipated to further exacerbate flood risk. The different soil types' physical, chemical, and biological characteristics significantly impact surface water movement, porosity, permeability, and infiltration potential. Therefore, soil infiltration is perhaps the most challenging and crucial process to characterize on a field scale. Various methods have been developed to measure the infiltration rate empirically and theoretically. However, the relationship between different soil types and infiltration rates in Sarawak remains unknown as no previous study has been conducted. This study uses the Storm Water Management Model (SWMM) to evaluate the infiltration rates for five different soil types: clay, clay loam, loam, sandy loam, and sand. 30 samples of various types and soil depths were examined at intervals of 0.5 m, 1.0 m, 1.5 m, 2.0 m, 2.5 m, and 3 m. The study was carried out using a standardized slope of 0.7% and an impervious land of 25% with a catchment size of 2 acres. Extreme rainfall data on the 5th and 6th of December 2021 was input into the infiltration model. Results showed that the difference between initial and final water storage of all the investigated soil depths for clay, clay loam, loam, sandy loam, and sand was found to be 48.42 mm, 51.20 mm, 58.01 mm, 66.96 mm, and 115.54 mm, respectively. The findings demonstrated that clay has the lowest water storage capability, followed by clay loam, loam, and sandy loam. Sand could store a comparatively large amount of rainwater. In contrast, sand has the highest infiltration rate with 2.541 mm/h, followed by sandy loam with 1.835 mm/h, loam with 1.432 mm/h, clay loam with 1.039 mm/h. Clay has the lowest infiltration rate, with 0.852 mm/h. This research concluded that sandy soil could significantly reduce surface runoff and help reduce flood risk in urban regions. [ABSTRACT FROM AUTHOR]

Copyright of Canadian Geotechnical Journal is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

We explore the soil physical characteristics in wetland of Barito Delta from primary data of soil sample and electrical resistivity measurement with the support from some secondary data. We also estimate saturated hydraulic conductivity (Ks) in Barito Delta from soil physical characteristics applying Saxton and Rawls (1986) and Weynants et al. (2009). Soil texture profile is determined from interpolation of soil fraction in each layer applying Bayesian statistics to analyze soil physical characteristics in the landforms of Delta. Clay is the dominant soil fraction in the soil of Barito Delta. Clay fraction percentage decrease along the depth of soil profile as it reaches fine sand particles deriving from ancient sedimentation from the past. It is an opposite with soil organic matter content that has contrast value from 1st to 2nd soil depth, but a few discrepancy from 3rd depth to downward direction. The content of clay in the soil depends on the sedimentation activity in the landform. Clay is dominant soil particle in the Delta; in case, it is in flat area and there is no intensive of sea water sedimentation such as in Basin of Peat Anticline and Natural Levee. In more than 2 m depth of soil, loamy sand and silty clay textures are mostly in the landform that is influenced by sea water activity, while by river water is clay loam. Ks values from Saxton and Rawls (1986) are close to Ks values from the measurement of previous studies. Ks values are generally small in Barito Delta that is mostly ranging from 1.10−7 to 2 m s−1. Ks values are larger following the depth of soil profile. The values of Ks are smaller in Basin of Peat Anticline and Natural Levee than in Tidal Flat and Beach Ridge. It is because both landforms have clay as dominant soil particles. [ABSTRACT FROM AUTHOR]

A three-dimensional numerical analysis is conducted on a group pile adjacent to a deep multi-strutted excavation in a naturally occurring soil profile comprising both cohesive and non-cohesive layers. The contrasting soil layers affect the soil stiffness, strength, and deformation characteristics, thereby impacting the load transfer mechanism within a pile group. The primary aim of this study is to specifically understand how the presence of a non-cohesive soil layer within a predominantly cohesive soil profile, affects the behavior of a pile group during excavation. By systematically varying the position and thickness of the soil layers, the analysis highlights the significance of considering the actual soil profile's inherent heterogeneity rather than assuming a homogeneous clay layer. 19.2% and 17% deviations respectively are observed for pile group settlement and lateral deflection when a homogeneous clay layer is considered instead of the natural soil profile. The findings also show that the position of the non-cohesive soil layer within a predominantly clay soil profile is more critical than its thickness in determining the pile response to excavation-induced changes. The non-cohesive soil layers within the excavation depth, significantly influence the lateral and axial pile behavior, while those below the final excavation depth have a limited impact. A theoretical simplified framework is proposed for the preliminary assessment of the excavation-induced effect on an adjacent pile group. This simplification helps minimize the initial calculation time and effort while capturing the significant factors affecting the pile group behavior near the excavation. [ABSTRACT FROM AUTHOR]

Copyright of Canadian Geotechnical Journal is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Variations in soil radon concentrations are a potential precursor of earthquake and volcanic events. However, the unclear migration and variation mechanisms of radon concentrations in soil still limit its effective application. To elucidate the temporal variation and its possible influence factors on radon concentrations at different soil depths, a case study was performed at a suburban site in Beijing. A long-term continuous measurement system consisting of ten radon-in-soil monitors at depths from 0.1 to 5.0 m and other meteorological sensors was employed. The monitoring was carried out from January 8th to July 29th, 2022, covering 3445 h in total. Radon concentrations generally increased with soil depth. Diurnal variation of soil radon concentrations at depths of 1.2 and 1.6 m in winter and spring was observed, and a negative correlation between the soil radon concentration and the residual air pressure was found. This finding indicates a possible air exchange channel between the soil and the atmosphere at the study site. In addition, the soil radon concentration at 4.0 m depth was unexpectedly lower than that of neighboring depths and was steady throughout the measurement period. This is attributed to a possible clay layer in the soil structure at 4.0 m depth. The results of this field study indicate that the complexity of temporal variation of soil radon concentrations should be considered for its application in predicting earthquake and volcanic events. • Continuous monitoring of radon concentrations in ten soil depths to 5.0 m. • Bi-periodic diurnal variation of radon concentrations at 0.8–3.0 m depth. • Negative correlation between radon concentration and air pressure. • Air exchange channel between soil and atmosphere might exist. [ABSTRACT FROM AUTHOR]

Considering the non-linear creep characteristics of clays, the modified unified hardening (UH) relation is employed to reflect the visco-elastic-plastic deformation of soft soils. Simultaneously, Swartzendruber's flow in the form of a continuous function is captured to describe pore water flow through pores during consolidation. Thus, an upgraded one-dimensional (1-D) non-linear rheological consolidation (NRC) system of clays has been established, and its solutions are conducted using the finite volume method (FVM). Through comparisons against the theoretical solutions and laboratory test results, the effectiveness of the numerical algorithm and applicability of the modified UH relation is verified. Then, the effects of model parameters on non-linear rheological consolidation behavior were studied. The results indicate that ignoring the time effect of secondary consolidation coefficient overestimates the overall consolidation and settlement proceeding, and considering the viscous effect of the soils led to an unanticipated increase in excess pore-water pressure (EPP) at the initial loading period. Meanwhile, the rising EPP becomes more pronounced with the increase of the initial over-consolidated parameter, flow parameter, and soil thickness or the decrease of overlying load. Additionally, FVM and finite difference method (FDM) solutions, as well as the application scope of Darcy's law in the NRC system, are discussed. [ABSTRACT FROM AUTHOR]

[Display omitted] • High soil P content was found in eastern and northern subtropical China. • Soil clay strongly and negatively affected regional-scale variation in soil P. • Humidity index and DBH indirectly affected soil available P via soil clay content. • Extending the rotation period benefits the recovery of soil P availability. Evaluating the environmental effects on soil phosphorus (P) availability is the key to understanding P cycling and regulating forest productivity. However, what and how environmental factors affect soil P availability in regional plantation ecosystems remains unclear. The study evaluated the effects of climatic factors, nitrogen deposition rate, stand attributes, litter characteristics, and soil-associated properties on soil P availability in Masson pine plantations across subtropical China using stepwise regression and structural equation modelling (SEM) analyses. At the 0–20 cm and 20–40 cm soil depths, soil total P ranged from 0.24 to 0.43 g kg−1 and from 0.24 to 0.48 g kg−1, respectively. Similarly, soil available P varied from 0.35 to 7.55 mg kg−1 and from 0.14 to 4.34 mg kg−1, respectively. Soil total and available P had high values in the eastern and northern distribution areas of subtropical China. Soil total P linearly decreased with an increase in bulk density, clay and pH but linearly increased with an increase in DBH. These four factors had a similar contribution (15.5–35.1 %) to soil total P. Soil available P linearly decreased with an increase in bulk density and clay. The relative contribution of clay (48.1–75.7 %) to soil available P was higher than that of bulk density (16.2–33.5 %). Soil total P decreased during the initial 30 years of plantations and then increased. But other variables (e.g., climate, nitrogen deposition, and litter) had no significant impacts on soil P. Overall, the SEM explained 35.4 % and 28.1 % of soil available P variations at the 0–20 cm and 20–40 cm soil depths, respectively, and revealed that clay had strong total effects (β = -0.526 and −0.396) on the soil available P. These results reveal the dominant roles of soil texture (especially clay) in affecting soil P availability in Masson pine plantations and suggest that extending the rotation period benefits soil P recovery in pine plantation ecosystems of subtropical China. [ABSTRACT FROM AUTHOR]

Full-flow penetrometers (ball and T-bar) are widely used for measurements of strength characteristics of clayey soils in offshore field investigations and laboratory tests. However, the accuracy of the estimated undrained shear strength is hampered by: (1) the drastic variation of the bearing factor for the penetrometer at shallow and transitional penetration depths where full-flow mechanisms are not achieved; and (2) the strain-softening of the soil, which results in a degradation of the estimated strength. This study conducted LDFE analyses to simulate the entire penetration process of full-flow penetrometers in strain-softening soils from shallow to deep embedment depths. Parametric studies were performed to investigate the effects of varied factors on the bearing factor and failure mechanism during the penetrometer penetration. Based on the LDFE analyses, empirical formulas are established to represent the critical penetration depths in the strain-softening soil, which are used to correct the bearing factor at shallow penetration depths. The discrepancies of the transitional failure mechanism and the trapped cavity bearing factor between ball and T-bar are emphasized. Finally, a back-analyses framework is proposed to estimate the strength parameters (including the original undrained shear strength prior to any strain-softening, and the strain-softening parameters) based on the measurements of the penetrometer during the first penetration from shallow to deep embedment depths. Through a series of model tests, the reliability of the back-analyses framework is validated. [ABSTRACT FROM AUTHOR]