Search

In the present work, the sintering of bismuth germanate through hot pressing and the improvement of scintillator performance were investigated. The linear shrinkage, crystalline structure, microstructure, transparency degree, and radioluminescence (RL) were studied as functions of the sintering pressure. X‐ray diffraction revealed that the samples were predominantly composed of the Bi4Ge3O12 phase, accompanied by small amounts of Bi12GeO20, with concentrations varying according to the sintering parameters. These concentrations were quantified through Rietveld refinement, which also indicated a tendency for the cell parameters to shrink as the sintering pressure increased. The microstructure of the ceramic pellets produced under varying hot‐pressing parameters was investigated using scanning electron microscopy (SEM), revealing that while the grain size was preserved, the porosity and grain boundary thickness were reduced by the hot pressing, forming a quasicontinuum in some areas of the sample. The RL of all the samples exhibited a green color, with a maximum at 540 nm, ascribed to the transitions from the 3P0,1,21P1 excited states to the fundamental 1S0 state of the Bi3+ ions. For samples sintered under a pressure of .18 MPa, the enhancement in the optical transmittance, accompanied by a 61.36% increase in light output at the maximum wavelength, was observed. [ABSTRACT FROM AUTHOR]

Ultra‐high‐speed synchrotron‐based hard X‐ray (i.e. above 10 keV) imaging is gaining a growing interest in a number of scientific domains for tracking non‐repeatable dynamic phenomena at spatio‐temporal microscales. This work describes an optimized indirect X‐ray imaging microscope designed to achieve high performance at micrometre pixel size and megahertz acquisition speed. The entire detector optical arrangement has an improved sensitivity within the near‐ultraviolet (NUV) part of the emitted spectrum (i.e. 310–430 nm wavelength). When combined with a single‐crystal fast‐decay scintillator, such as LYSO:Ce (Lu2−xYxSiO5:Ce), it exploits the potential of the NUV light‐emitting scintillators. The indirect arrangement of the detector makes it suitable for high‐dose applications that require high‐energy illumination. This allows for synchrotron single‐bunch hard X‐ray imaging to be performed with improved true spatial resolution, as herein exemplified through pulsed wire explosion and superheated near‐nozzle gasoline injection experiments at a pixel size of 3.2 µm, acquisition rates up to 1.4 MHz and effective exposure time down to 60 ps. [ABSTRACT FROM AUTHOR]

The prevalent use of unsustainable polymers in current X‐ray scintillators poses a significant environmental concern. The advancement of biodegradable X‐ray scintillators holds promise in mitigating escalating environmental issues tied to electronic or medical waste and carbon footprints. Herein, a biodegradable and flexible X‐ray scintillation film is presented employing lead‐free 0D Cs3Cu2I5 perovskite nanoparticles integrated into densified‐delignified wood (Cs3Cu2I5@D‐Wood). The Cs3Cu2I5@D‐Wood film demonstrates precise and detailed X‐ray imaging capabilities, achieving a high spatial resolution of 10 line pairs per millimeter (lp·mm−1). To minimize the environmental impact associated with disposal, metal and halide ions (e.g., Cs+, Cu+, I−) from Cs3Cu2I5@D‐Wood can be easily retrieved by a simple solvent extraction process. The approach showcases the potential of biodegradable wood‐based X‐ray scintillation screens as alternatives to conventional, plastic‐based screens. This offers a significant contribution to environmental sustainability by reducing electronic or medical waste. [ABSTRACT FROM AUTHOR]

Neutrons are widely used in national defense, security, and medical health fields. It is critical to realize neutron detection with high efficiency. The most popular neutron detection scintillators such as lithium glass and 6LiF/ZnS:Ag screen exhibit insurmountable limitations: the former usually has relatively rather low light yield and latter is opaque. In this research, we report the successful construction of the novel full inorganic composite scintillators by low temperature co‐firing technology. The composite scintillator is derived from the ZnS:Ag and borate glass matrix, and it shows better transparency compared with the standard 6LiF/ZnS:Ag screen. It exhibits excellent scintillation properties with the X‐ray induced emission intensity of these composite scintillators reaching approximately 2.46 times of the standard Bi4Ge3O12 (BGO) crystal. The light output under thermal neutron excitation can reach 75 000 photons/neutron. In addition, it presents excellent neutron detection performance with natural abundance of 10B isotope. Our research findings can serve as a valuable reference for the advancement of robust neutron detection materials, particularly in the domain of ZnS:Ag‐based full inorganic scintillator for neutron detection. [ABSTRACT FROM AUTHOR]

Purpose: This study investigated the potential of a commercially available plastic scintillator, the Exradin W2, as a real‐time dosimeter for ultra‐high‐dose‐rate (UHDR) electron beams. This work aimed to characterize this system's performance under UHDR conditions and addressed limitations inherent to other conventional dosimetry systems. Methods and materials: We assessed the W2's performance as a UHDR electron dosimeter using a 16 MeV UHDR electron beam from the FLASH research extension (FLEX) system. Additionally, the vendor provided a beta firmware upgrade to better handle the processing of the high signal generated in the UHDR environment. We evaluated the W2 regarding dose‐per‐pulse, pulse repetition rate, charge versus distance, and pulse linearity. Absorbed dose measurements were compared against those from a plane‐parallel ionization chamber, optically stimulated luminescent dosimeters and radiochromic film. Results: We observed that the 1 × 1 mm W2 scintillator with the MAX SD was more suitable for UHDR dosimetry compared to the 1 × 3 mm W2 scintillator, capable of matching film measurements within 2% accuracy for dose‐per‐pulse up to 3.6 Gy/pulse. The W2 accurately ascertained the inverse square relationship regarding charge versus virtual source distance with R2 of ∼1.00 for all channels. Pulse linearity was accurately measured with the W2, demonstrating a proportional response to the delivered pulse number. There was no discernible impact on the measured charge of the W2 when switching between the available repetition rates of the FLEX system (18–180 pulses/s), solidifying consistent beam output across pulse frequencies. Conclusions: This study tested a commercial plastic scintillator detector in a UHDR electron beam, paving the way for its potential use as a real‐time, patient‐specific dosimetry tool for future FLASH radiotherapy treatments. Further research is warranted to test and improve the signal processing of the W2 dosimetry system to accurately measure in UHDR environments using exceedingly high dose‐per‐pulse and pulse numbers. [ABSTRACT FROM AUTHOR]

The high durability under harsh environment including high temperature, high humidity, and high radiation is required for scintillators used for decommissioning of nuclear facilities and radiation monitoring in nuclear fusion reactors. α‐SiAlON ceramics are highly potential for such scintillators because of their thermal and mechanical durability and luminescence corresponding to doped rare‐earth ion. In this study, scintillation properties of transparent Lu‐α‐SiAlON:Ce3+ ceramics were investigated for the first time. Lu‐α‐SiAlON:Ce3+ showed the scintillation responses to α‐rays and X‐rays. The α‐rays‐induced scintillation decay curve consists of two components whose decay time are 48 and 652 ns. The faster decay component most presumably results from 4f‐5d transition of Ce3+, whereas the origin of the slower one is unclear but may be defects in α‐SiAlON. The light yield of the Lu‐α‐SiAlON:Ce3+ ceramics was 1300 photons 5.5 MeV−1. [ABSTRACT FROM AUTHOR]

Organic scintillators have recently gained considerable attentions in X‐ray detection for their potential applications in biomedical radiograph and security inspection. However, the weak X‐ray absorption and/or inefficient exciton utilization have limited the development and commercialization of organic scintillators. Currently, high‐performance X‐ray organic scintillators are scarce and organic scintillators with dual triplet‐harvesting channels have not been explored before. Here, we develop several proof‐of‐concept sulfone‐based organic molecules, C1–C7, using different alkoxy chains to manipulate molecular packing mode. These materials exhibit dual triplet‐harvesting channels of thermally activated delayed fluorescence (TADF) and room‐temperature phosphorescence (RTP) in aggregated state. Inspiringly, these molecules display distinct radioluminescence under the X‐ray stimulation. Among them, C6 behaves the highest light yield of 16,558 photons MeV−1. Moreover, clear X‐ray images are demonstrated in both aggregated state and single‐molecule level. High spatial resolutions of 15.0 and 10.6 line pairs per millimeter (lp mm−1) are achieved for rigid and flexible scintillator screens, exceeding most reported organic and conventional inorganic scintillators. These results highlight the great potential of organic molecules with TADF and RTP nature for efficient X‐ray scintillation and imaging. [ABSTRACT FROM AUTHOR]

Introduction: Radiation dose measurement is an essential part of radiotherapy to verify the correct delivery of doses to patients and ensure patient safety. Recent advancements in radiotherapy technology have highlighted the need for fast and precise dosimeters. Technologies like FLASH radiotherapy and magnetic‐resonance linear accelerators (MR‐LINAC) demand dosimeters that can meet their unique requirements. One promising solution is the plastic scintillator‐based dosimeter with high spatial resolution and real‐time dose output. This study explores the feasibility of using the LuSy dosimeter, an in‐house developed plastic scintillator dosimeter for dose verification across various radiotherapy techniques, including conformal radiotherapy (CRT), intensity‐modulated radiation therapy (IMRT), volumetric‐modulated arc therapy (VMAT), and stereotactic radiosurgery (SRS). Materials and methods: A new dosimetry system, comprising a new plastic scintillator as the sensing material, was developed and characterized for radiotherapy beams. Treatment plans were created for conformal radiotherapy, IMRT, VMAT, and SRS and delivered to a phantom. LuSy dosimeter was used to measure the delivered dose for each plan on the surface of the phantom and inside the target volumes. Then, LuSy measurements were compared against an ionization chamber, MOSFET dosimeter, radiochromic films, and dose calculated using the treatment planning system (TPS). Results: For CRT, surface dose measurement by LuSy dosimeter showed a deviation of ‐5.5% and ‐5.4% for breast and abdomen treatment from the TPS, respectively. When measuring inside the target volume for IMRT, VMAT, and SRS, the LuSy dosimeter produced a mean deviation of ‐3.0% from the TPS. Surface dose measurement resulted in higher TPS discrepancies where the deviations for IMRT, VMAT, and SRS were ‐2.0%, ‐19.5%, and 16.1%, respectively. Conclusion: The LuSy dosimeter was feasible for measuring radiotherapy doses for various treatment techniques. Treatment delivery verification enables early error detection, allowing for safe treatment delivery for radiotherapy patients. [ABSTRACT FROM AUTHOR]

Near‐infrared (NIR) luminescent metal halide (LMH) materials have attracted great attention in various optoelectronic applications due to their low‐temperature solution‐processable synthesis, abundant crystallographic/electronic structures, and unique optoelectronic properties. However, some challenges still remain in their luminescence design, performance improvement, and application assignments. This review systematically summarizes the development of NIR LMHs through classifying NIR luminescent origins into four major categories: band‐edge emission, self‐trapped exciton (STE) emission, ion emission, and defect‐related emission. The luminescence mechanisms of different types of NIR LMHs are discussed in detail by analyzing typical examples. Reasonable strategies for designing and optimizing luminescence/optoelectronic properties of NIR LMHs are summarized, including bandgap engineering, self‐trapping state engineering, chemical composition modification, energy transfer, and other auxiliary strategies such as improvement of synthesis scheme and post‐processing. Furthermore, application prospects based on the optoelectronic devices are revealed, including phosphor‐converted light‐emitting diodes (LEDs), electroluminescent LEDs, photodetectors, solar cells, and x‐ray scintillators, as well as demonstrations of some related practical applications. Finally, the existing challenges and future perspectives on the development of NIR LMH materials are critically proposed. This review aims to provide general understanding and guidance for the design of high‐performance NIR LMHs materials. [ABSTRACT FROM AUTHOR]

Purpose: To directly compare the radiation and imaging isocenters of a proton treatment machine, we developed and evaluated a real‐time radiation isocenter verification system. Methods: The system consists of a plastic scintillator (PI‐200, Mitsubishi Chemical Corporation, Tokyo, Japan), an acrylic phantom, a steel ball on the detachable plate, Raspberry Pi 4 (Raspberry Pi Foundation, London, UK) with camera module, and analysis software implemented through a Python‐based graphical user interface (GUI). After kV imaging alignment of the steel ball, the imaging isocenter defined as the position of the steel ball was extracted from the optical image. The proton star‐shot was obtained by optical camera because the scintillator converted proton beam into visible light. Then the software computed both the minimum circle radius and the radiation isocenter position from the star‐shot. And the deviation between the imaging isocenter and radiation isocenter was calculated. We compared our results with measurements obtained by Gafchromic EBT3 film (Ashland, NJ, USA). Results: The minimum circle radii were averaged 0.29 and 0.41 mm while the position deviations from the radiation isocenter to the laser marker were averaged 0.99 and 1.07 mm, for our system and EBT3 film, respectively. Furthermore, the average position difference between the radiation isocenter and imaging isocenter was 0.27 mm for our system. Our system reduced analysis time by 10 min. Conclusions: Our system provided automated star‐shot analysis with sufficient accuracy, and it is cost‐effective alternative to conventional film‐based method for radiation isocenter verification. [ABSTRACT FROM AUTHOR]

Time‐of‐flight (TOF) technique, traditionally used in high energy physics (HEP) and positron emission tomography (PET), is now being explored for lower energy applications like computed tomography (CT). Regardless of the application, pushing the current boundaries in time resolution calls for novel technologies and materials exhibiting ultra‐fast time response. Semiconductor nanocrystals like cesium lead halide perovskites (CsPbBr3), benefiting from quantum confinement effects, feature ultra‐fast decay and, when combined with a suitable bulk scintillator following a heterostructure concept, can also provide the necessary stopping power. In this work, thin films of CsPbBr3 on top of BGO, LYSO:Ce, and GAGG:Ce,Mg wafers are fabricated to test their impact on the single crystal scintillator time resolution under soft X‐rays excitation (about 10 keV). It is demonstrated that the CsPbBr3 layer significantly improves the overall time resolution in all cases, achieving up to a tenfold improvement with BGO and GAGG:Ce,Mg. Under 511 keV γ‐rays, a proof‐of‐concept of the heterostructure design for TOF‐PET using CsPbBr3 thin film deposited on GAGG:Ce,Mg bulk crystal is successfully tested. Shared events depositing energy in both materials are identified, resulting in more than twofold improved coincidence time resolution: 118 ± 4 ps full‐width‐at‐half‐maximum (FWHM) compared to the 272 ± 8 ps of solely GAGG:Ce,Mg. [ABSTRACT FROM AUTHOR]

Scintillators, which can convert high‐energy particles (X‐rays) into detectable low‐energy ultraviolet–visible–near‐infrared photons, are essential components of X‐ray detectors and show extensive practical applications in nondestructive detection and medical imaging. Traditionally, inorganic scintillators represented by CsI:Tl have achieved definite progress. However, the harsh preparation conditions, high production cost, and poor mechanical properties impede their potential development in the high‐end X‐ray imaging field. Organic–inorganic hybrid metal complexes could be excellent alternatives, by virtue of their structural and spectral tunability, good solution processability, and excellent photophysical properties. This review mainly focuses on eco‐friendly lead‐free metal (Mn2+, Cu+, Sb3+, Sn2+, Ge2+, Ln3+, etc.) complex scintillators. The luminescence mechanisms are introduced and the scintillation performance, such as light yield, limit of detection, imaging resolution, etc., is highlighted. Moreover, the current challenges and perspectives in this emerging field are described. It is hoped to provide some theoretical guidance for the continuous development of the new scintillator systems. [ABSTRACT FROM AUTHOR]

High‐pressure chemistry has provided a huge boost to the development of scientific community. Pressure‐induced emission (PIE) in halide perovskites is gradually showing its unique charm in both pressure sensing and optoelectronic device applications. Moreover, the PIE retention of halide perovskites under ambient conditions is of great commercial value. Herein, we mainly focus on the potential applications of PIE and PIE retention in metal halide perovskites for scintillators and solid‐state lighting. Based on the performance requirements of scintillator and single‐component white light‐emitting diodes (WLEDs), the significance of PIE and PIE retention is critically clarified, aiming to design and synthesize materials used for high‐performance optoelectronic devices. This perspective not only demonstrates promising applications of PIE in the fields of scintillators and WLEDs, but also provides potential applications in display imaging and anti‐counterfeiting of PIE materials. Furthermore, solving the scientific disputes that exist under ambient conditions is also simply discussed as an outlook by introducing high‐pressure dimension to produce PIE. [ABSTRACT FROM AUTHOR]

Background: Pulsed reduced dose rate (PRDR) is an emerging radiotherapy technique for recurrent diseases. It is pertinent that the linac beam characteristics are evaluated for PRDR dose rates and a suitable dosimeter is employed for IMRT QA. Purpose: This study sought to investigate the pulse characteristics of a 6 MV photon beam during PRDR irradiations on a commercial linac. The feasibility of using EBT3 radiochromic film for use in IMRT QA was also investigated by comparing its response to a commercial diode array phantom. Methods: A plastic scintillator detector was employed to measure the photon pulse characteristics across nominal repetition rates (NRRs) in the 5–600 MU/min range. Film was irradiated with dose rates in the 0.033–4 Gy/min range to study the dose rate dependence. Five clinical PRDR treatment plans were selected for IMRT QA with the Delta4 phantom and EBT3 film sheets. The planned and measured dose were compared using gamma analysis with a criterion of 3%/3 mm. EBT3 film QA was performed using a cumulative technique and a weighting factor technique. Results: Negligible differences were observed in the pulse width and height data between the investigated NRRs. The pulse width was measured to be 3.15 ± 0.01 μs$\mu s$ and the PRF was calculated to be 3–357 Hz for the 5–600 MU/min NRRs. The EBT3 film was found to be dose rate independent within 3%. The gamma pass rates (GPRs) were above 99% and 90% for the Delta4 phantom and the EBT3 film using the cumulative QA method, respectively. GPRs as low as 80% were noted for the weighting factor EBT3 QA method. Conclusions: Altering the NRRs changes the mean dose rate while the instantaneous dose rate remains constant. The EBT3 film was found to be suitable for PRDR dosimetry and IMRT QA with minimal dose rate dependence. [ABSTRACT FROM AUTHOR]

High‐resolution X‐ray imaging is increasingly required for medical diagnosis and large‐area detection. However, the issues of scattering and optical crosstalk are limiting the spatial resolution of the indirect X‐ray imaging. In this study, a feasible and efficient strategy is proposed to in situ synthesize flexible Cs3Cu2I5:2%In+@paper as a superior scintillator film, which can be scaled up to an ultra‐large area of 4800 cm2. The as‐obtained Cs3Cu2I5:2%In+@paper performs a fascinating photoluminescence quantum efficiency up to 88.14%, a steady state light yield of 70169 photons/MeV, and spatial resolution of 15 lp mm−1. Moreover, the suppressed physical scattering and optical crosstalk of the corresponding film are demonstrated. Accordingly, this work explores a feasible fabrication of customizable scintillation films with large area for high‐resolution X‐ray detection. [ABSTRACT FROM AUTHOR]

Metal halide crystals are bright but hygroscopic scintillator materials that are widely used in X‐ray imaging and detectors. Precipitating them in situ in glass to form glass ceramics (GCs) scintillator offers an efficient avenue for large‐scale preparation, high spatial resolution, and excellent stability. However, precipitating a high fraction of metal halide nanocrystals in glass to maintain high light yield remains a challenge. Herein, an ionic‐covalent hybrid network strategy for constructing GCs scintillator with high crystallinity (up to ≈37%) of BaCl2: Eu2+ nanocrystals is presented. Experimental data and simulations of glass structure reveal that the Ba2+‐Cl− clustering promotes the high crystallization of BaCl2 nanocrystals. The ultralow phonon energy (≈200 cm−1) of BaCl2 nanocrystals and good Eu reduction effect enable high photoluminescence inter quantum efficiency (≈80.41%) in GC. GCs with varied crystallinity of BaCl2: Eu2+ nanocrystals demonstrate efficient radioluminescence and tunable scintillator performance. They either outperform Bi4Ge3O14 single crystal by over 132% steady‐state light yield or provide impressive X‐ray imaging resolutions of 20 lp mm−1. These findings provide a new design strategy for developing bright transparent GCs scintillators with a high fraction of metal halide nanocrystals for X‐ray high‐resolution imaging applications. [ABSTRACT FROM AUTHOR]

Purpose: To evaluate the performance of an electromagnetic (EM)‐tracked scintillation dosimeter in detecting source positional errors of IVD in HDR brachytherapy treatment. Materials and Methods: Two different scintillator dosimeter prototypes were coupled to 5 degrees‐of‐freedom (DOF) EM sensors read by an Aurora V3 system. The scintillators used were a 0.3 × 0.4 × 0.4 mm3 ZnSe:O and a BCF‐60 plastic scintillator of 0.5 mm diameter and 2.0 mm in length (Saint‐Gobain Crystals). The sensors were placed at the dosimeter's tip at 20.0 mm from the scintillator. The EM sampling rate was 40/s while the scintillator signal was sampled at 100 000/s using two photomultiplier tubes from Hamamatsu (series H10722) connected to a data acquisition board. A high‐pass filter and a low‐pass filter were used to separate the light signal into two different channels. All measurements were performed with an afterloader unit (Flexitron‐Elekta AB, Sweden) in full‐scattered (TG43) conditions. EM tracking was further used to provide distance/angle‐dependent energy correction for the ZnSe:O inorganic scintillator. For the error detection part, lateral shifts of 0.5 to 3 mm were induced by moving the source away from its planned position. Indexer length (longitudinal) errors between 0.5 to 10 mm were also introduced. The measured dose rate difference was converted to a shift distance, with and without using the positional information from the EM sensor. Results: The inorganic scintillator had both a signal‐to‐noise‐ratio (SNR) and signal‐to‐background‐ratio (SBR) close to 70 times higher than those of the plastic scintillator. The mean absolute difference from the dose measurement to the dose calculated with TG‐43U1 was 1.5% ±0.7%. The mean absolute error for BCF‐60 detector was 1.7% ±1.2%$\pm 1.2\%$ when compared to TG‐43 calculations formalism. With the inorganic scintillator and EM tracking, a maximum area under the curve (AUC) gain of 24.0% was obtained for a 0.5‐mm lateral shift when using the EMT data with the ZnSe:O. Lower AUC gains were obtained for a 3‐mm lateral shifts with both scintillators. For the plastic scintillator, the highest gain from using EM tracking information occurred for a 0.5‐mm lateral shift at 20 mm from the source. The maximal gain (17.4%) for longitudinal errors was found at the smallest shifts (0.5 mm). Conclusions: This work demonstrates that integrating EM tracking to in vivo scintillation dosimeters enables the detection of smaller shifts, by decreasing the dosimeter positioning uncertainty. It also serves to perform position‐dependent energy correction for the inorganic scintillator,providing better SNR and SBR, allowing detection of errors at greater distances from the source. [ABSTRACT FROM AUTHOR]

High‐energy physics community is looking for a hard, fast, and low‐cost scintillation material, and Ce:Lu3Al5O12 (Ce:LuAG) ceramic is one of the competitive candidates. This work presents Ce,Ca:LuAG scintillation ceramics with good optical quality, and the influence of Ce and Ca concentrations on optical and scintillation properties was fully analyzed. At relatively low level of Ce concentration, the less Ca2+ content is needed to achieve a significant intensity increase in fast scintillation component while maintaining a relatively high light yield (LY). The introduction of only 0.1 at% Ca2+ could increase the LY0.5 μs/LY3.0 μs from 79.9% to 96.1% in Ce,Ca:LuAG ceramics of 0.1 at% Ce. First‐principles investigations are further performed to reveal the tuning mechanisms of the scintillation properties of LuAG by Ce and Ca codoping. We show that the Fermi level shifts down with Ca codoping, which increases the Ce4+ content and decreases the depth of the electron traps (VO), resulting to a faster decay. Moreover, the formation preference of Ca‐VO complexes over Ce‐VO leads to the suppression of the non‐radiative decay of Ce via VO. In summary, our study demonstrates the realization of the performance tuning of LuAG via Ce and Ca codoping. [ABSTRACT FROM AUTHOR]

In this study, a new Cs4SrI6:Yb2+,Sm2+ near‐infrared (NIR) emitting scintillator was developed using sensitization strategy. It was found that Yb2+ sensitization significantly enhances the NIR radioluminescence (RL) of Sm2+, providing a new approach of designing highly emissive sensitized NIR scintillators. By studying the optical spectra and decay kinetics of Cs4SrI6:Yb2+,Sm2+, it was revealed that the energy transfer pathways involve both radiative and nonradiative processes. The gamma spectroscopy performance of Cs4SrI6:Yb2+,Sm2+ single crystals was studied by using the high‐quantum‐efficiency avalanche photodiode (APD) as the readout. Our results highlight the importance of using sensitization strategy of achieving NIR emitting scintillators and demonstrate the significant potential for radiation detection applications. [ABSTRACT FROM AUTHOR]

Traditional‐metal‐containing scintillators are widely used in X‐ray imaging due to their efficient X‐ray absorption and output of visible light. However, they suffer from heavy‐metal toxicity, environmental stability, harsh preparation, and afterglow. Metal‐free organic scintillators show a rising momentum, especially organic‐halogen‐containing molecules. Halogens are introduced to improve their X‐ray absorption, but the resulting increase in spin–orbit coupling leads to significant delayed fluorescence or phosphorescence, affecting the response speed to X‐rays. Moreover, there is still insufficient practice in fabricating microstructured organic scintillators for high spatial resolution of imaging. Herein, the preparation of nano organic co‐crystals (t‐Bpe‐IFB co‐crystal, abbreviated as BIC, t‐Bpe for trans‐1,2‐bis(4‐pyridyl)ethylene, and IFB for 1,3,5‐trifluoro‐2,4,6‐triiodobenzene) and its application in X‐ray imaging are explored. In contrast to previous single organic‐halogen‐containing molecules, BIC generates nanosecond‐scale fluorescence through the charge‐transfer state of the donor–acceptor. Its high iodine content ensures large X‐ray absorption, strong radioluminescence, and a low detection limit of 85 nGyair s−1. The composite film made of nano‐sized BICs and polydimethylsiloxane exhibits a high spatial resolution of 16.7 lp mm−1. Herein, the application of organic co‐crystals is expanded and ideas are provided for the development of new scintillators. [ABSTRACT FROM AUTHOR]

Single‐component metal halides with white light emission are highly attractive for solid‐state lighting applications, but it is still challenging to develop all‐inorganic lead‐free metal halides with high white‐light emission efficiency. Herein, by rationally introducing silver (Ag) into zero‐dimensional (0D) Cs3Cu2Br5 as new structural building unit, a one‐dimensional (1D) bimetallic halide Cs6Cu3AgBr10 is designed that emits strong warm‐white light with an impressive photoluminescence quantum yield (PLQY) of 94.5% and excellent stability. This structural transformation lowers the conduction band minimum while maintaining the localized nature of the valence band maximum, which is crucial in expanding the excitation spectrum and obtaining efficient self‐trapped excitons (STEs) emission simultaneously. Detailed spectroscopy studies reveal that the white‐light originates from triplet STEs emission, which can be remarkably improved by weakening the strong electron‐phonon coupling and thus suppressing phonon‐induced non‐radiative processes. Moreover, the interesting temperature‐dependent emission behavior, together with self‐absorption‐free property, make Cs6Cu3AgBr10 as sensitive luminescent thermometer and high‐performance X‐ray scintillator, respectively. These findings demonstrate a general approach to achieving effective single‐component white‐light emitters based on lead‐free, all‐inorganic metal halides, thereby opening up a new avenue to explore their versatile applications such as lighting, temperature detection and X‐ray imaging. [ABSTRACT FROM AUTHOR]

X‐ray induced photodynamic therapy (X‐PDT) circumvents the poor penetration depth of conventional PDT with minimal radio‐resistance generation. However, conventional X‐PDT typically requires inorganic scintillators as energy transducers to excite neighboring photosensitizers (PSs) to generate reactive oxygen species (ROS). Herein, a pure organic aggregation‐induced emission (AIE) nanoscintillator (TBDCR NPs) that can massively generate both type I and type II ROS under direct X‐ray irradiation is reported for hypoxia‐tolerant X‐PDT. Heteroatoms are introduced to enhance X‐ray harvesting and ROS generation ability, and AIE‐active TBDCR exhibits aggregation‐enhanced ROS especially less oxygen‐dependent hydroxyl radical (HO•−, type I) generation ability. TBDCR NPs with a distinctive PEG crystalline shell to provide a rigid intraparticle microenvironment show further enhanced ROS generation. Intriguingly, TBDCR NPs show bright near‐infrared fluorescence and massive singlet oxygen and HO•− generation under direct X‐ray irradiation, which demonstrate excellent antitumor X‐PDT performance both in vitro and in vivo. To the best of knowledge, this is the first pure organic PS capable of generating both 1O2 and radicals (HO•−) in response to direct X‐ray irradiation, which shall provide new insights for designing organic scintillators with excellent X‐ray harvesting and predominant free radical generation for efficient X‐PDT. [ABSTRACT FROM AUTHOR]

Organic–inorganic halide perovskite single crystals (SCs) are promising materials for detecting ionizing radiation owing to their outstanding photoelectric conversion capability and inexpensive solution processability. However, the accuracy and stability of the detectors have been limited due to the charge traps and defects in SCs, especially when operated under high‐precision photon‐counting mode for energy spectrum acquisition. Here, we proposed a trap freezing deactivation route, which obviously suppressed dark current and noise by up to 97% and 92%, respectively. Furthermore, the bulk ion migration effect was essential for the ability to instantly self‐heal defects induced by radiation damage at temperatures down to −30°C. Consequently, the detector exhibits a record high energy resolution of 7.5% at 59.5 keV for 241Am γ‐ray source, which is the best solution‐processed semiconductor radiation detectors at the same energy range. In addition, the detector maintains over 90% of its initial performance after 9 months of storage when tested in the air. Our results will represent a revision of the paradigm that high‐spectral‐resolution and robust radiation detectors can only be realized with high temperature grown inorganic semiconductor single crystals. [ABSTRACT FROM AUTHOR]

Gas sensors are useful for monitoring of greenhouse gases. As the move toward complementary metal‐oxide‐semiconductor (CMOS) compatible pyroelectric room temperature detectors is gaining traction due to its scalability to 8‐in./12‐in. wafer area and integrable with CMOS electronics, CMOS compatible aluminum nitride (AlN)‐ and scandium aluminum nitride (ScAlN)‐based pyroelectric detectors are developed for sensing of CO2and CH4gases, which are two of the greenhouse gases that contribute significantly to global warming. Leveraging gas absorption at respective mid‐infrared (IR) wavelengths, CO2 and CH4 gases are detected at various concentrations with fast response time ≈1 s. A compound parabolic collector (CPC) is designed and integrated into the gas sensor to enhance the optical flux received by the detector, which demonstrates ≈10× signal improvement in its presence. Further factors such as the effect of sensing area reduction and response to random gas concentrations are also tested on AlN‐ and ScAlN‐based pyroelectric detectors respectively to observe the gas sensing behaviors of both detectors. The results obtained provide further understanding of the behavior of CMOS AlN‐ and ScAlN‐based pyroelectric detectors as IR gas sensors, which can potentially inspire new design and design selection for various gas sensing applications. [ABSTRACT FROM AUTHOR]

X‐ray imaging technology is critical to numerous different walks of daily life, ranging from medical radiography and security screening all the way to high‐energy physics. Although several organic chromophores are fabricated and tested as X‐ray imaging scintillators, they generally show poor scintillation performance due to their weak X‐ray absorption cross‐section and inefficient exciton utilization efficiency. Here, a singlet fission‐based high‐performance organic X‐ray imaging scintillator with near unity exciton utilization efficiency is presented. Interestingly, it is found that the X‐ray sensitivity and imaging resolution of the singlet fission‐based scintillator are dramatically improved by an efficient energy transfer from a thermally activated delayed fluorescence (TADF) sensitizer, in which both singlet and triplet excitons can be efficiently harnessed. The fabricated singlet fission‐based scintillator exhibits a high X‐ray imaging resolution of 27.5 line pairs per millimeter (lp mm−1), which exceeds that of most commercial scintillators, demonstrating its high potential use in medical radiography and security inspection. [ABSTRACT FROM AUTHOR]

Scintillating materials that convert ionizing radiation into low‐energy photons hold great potential for radiation detection, nondestructive inspection, medical radiography, and space exploration. However, organic scintillators are characterized by low radioluminescence, while bulky inorganic scintillators are not suitable for the development of flexible detectors. Here, high‐resolution X‐ray imaging using solution‐processable lanthanide‐based metal–organic frameworks as microscale scintillators is demonstrated. Mechanistic studies suggest that lanthanide ions absorb X‐rays to generate high‐density molecular triplet excitons, and excited linkers subsequently sensitize lanthanide ions via nonradiative resonance energy transfer. Furthermore, the crystalline nature offers a delocalized electronic feature rather than isolated subunits, which enables direct trapping of charge carriers by lanthanide emitters. By controlling the concentration ratio between Tb3+ and Eu3+ ions, efficient and color‐tunable radioluminescence of lanthanide ions can be achieved. When coupled with elastic, transparent polymer matrices, these metal–organic framework‐based microscintillators allow the fabrication of flexible X‐ray detectors. Such detectors feature a detection limit of 23 nGy s−1, which is 240 times lower than the typical radiation dose for medical diagnosis. X‐ray imaging with resolution higher than 16.6 line pairs per millimeter is further demonstrated. These findings provide insight into the future design of hybrid scintillators for optoelectronics and X‐ray sensing and imaging. [ABSTRACT FROM AUTHOR]

The search for color‐tunable, efficient, and robust scintillators plays a vital role in the development of modern X‐ray radiography. The radioluminescence tuning of copper iodide cluster scintillators in the entire visible region by bandgap engineering is herein reported. The bandgap engineering benefits from the fact that the conduction band minimum and valence band maximum of copper iodide cluster crystals are contributed by atomic orbitals from the inorganic core and organic ligand components, respectively. In addition to high scintillation performance, the as‐prepared crystalline copper iodide cluster solids exhibit remarkable resistance toward both moisture and X‐ray irradiation. These features allow copper iodide cluster scintillators to show particular attractiveness for low‐dose X‐ray radiography with a detection limit of 55 nGy s−1, a value ≈100 times lower than a standard dosage for X‐ray examinations. The results suggest that optimizing both inorganic core and organic ligand for the building blocks of metal halide cluster crystals may provide new opportunities for a new generation of high‐performance scintillation materials. [ABSTRACT FROM AUTHOR]

The toxicity of heavy‐metal Pb and instability of lead‐based halide perovskite nanomaterials are main factors to impede their practical applications in the fields of solar cells, LEDs and scintillators. In this paper, all inorganic lead‐free cesium manganese halide nanocrystals are synthesized in glass for the first time. Red photoluminescence with broad PL band, negligible self‐absorption and a high photoluminescence quantum yield of 41.8% is obtained. In addition, modulating halide component can change the Mn2+ ions coordination environment to obtain tunable photoluminescence from red to green. More importantly, cesium manganese halide nanocrystals embedded glasses exhibit outstanding long‐term stabilities. Theses cesium manganese halide nanocrystals embedded glasses are also highly stable against high energy irradiation and exhibit highly efficient radioluminescence, making them promising for high‐resolution X‐ray imaging. These results demonstrate that cesium manganese halide nanocrystals embedded glasses are promising eco‐friendly candidates for applications in light‐emitting diodes and scintillators. [ABSTRACT FROM AUTHOR]

Ce3+‐doped 20Gd2O3–20Al2O3–60SiO2 (GAS:xCe3+) glasses (x = 0.3, 0.7, 1.1, 1.5, 1.9 mol%) with Si3N4 as a reducing agent were prepared. The density of the glasses is around 4.2 g/cm3. With the increase in the Ce3+ concentration, both the photoluminescence (PL) and PL excitation peaks of GAS:xCe3+ glasses show a redshift because the 4f–5d energy levels of Ce3+ ions are narrowed. PL quantum yield and PL decay time of GAS:xCe3+ glasses are 28.32–50.59% and 43–64 ns, respectively. In addition, they both first increases and then decreases with the Ce3+ concentration increasing, reached the maximum when x = 1.1 mol%. The integrated X‐ray excited luminescence (XEL) intensity of the GAS:1.1Ce3+ glass is 23.86% of that of Bi4Ge3O12 (BGO) crystal, and the light yield reaches 1200 ph/MeV with an energy resolution of 22.98% at 662 keV when exposed to γ‐rays. The PL and XEL thermal activation energies of GAS:xCe3+ glasses are independent of Ce3+ ions concentration. Scintillating decay time of the glasses exhibits two components consisting of nanosecond and microsecond levels, and the scintillating decay time gradually decreases with the Ce3+ concentration increasing. The difference between PL and scintillating decay time is discussed regarding the different luminescent mechanisms. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the necessity of extending the output factor table (OF Table) of the Varian EclipseTM Treatment Planning System for small field stereotactic radiosurgery (SRS) and stereotactic body radiosurgery (SBRT) treatments. Methods: A new AcurosXB 15.6 beam model was created in the Eclipse Beam Configuration, which is identical to the one that has been used in the clinic with a default 3 × 3 cm to 40 × 40 cm OF Table, except the OF Table in the new model was extended to cover the range from 1 × 1 cm to 40 × 40 cm. 80 small square and rectangular output factors were measured on a Varian TrueBeam utilizing a Standard Imaging Exradin W2‐1×1 scintillator detector, inside a PTW BeamScan water tank with 95 cm SSD at 5 cm depth. Cerenkov contamination was corrected using a rectangular field method (2 cm × 15 cm field). Nine Radiosurgery plans with primary jaw setting ranging from 0.7 cm to 2.0 cm were evaluated by both beam models. The monitor unit (MU) differences between the two beam models were calculated for identical 3‐dimensional (3D) absolute dose distributions. Output factors, measured versus Eclipse calculated, were compared down to 0.5 × 0.5 cm primary jaw setting. Results: For the 6FFF beam, the difference between the two beam models was ∼ 6% for 1 × 1 cm jaw settings and 4% at 1.5 × 1.5 cm, with the extended OF Table requiring higher MUs for the same dose prescription and same 3‐dimensional isodose distribution. For the 6MV beam, the corresponding difference is ∼7.5% for 1 × 1 cm, 5% for 1.5 × 1.5 cm, and 3% for 2 × 2 cm jaw settings, with the extended OF Table requiring higher MUs. For jaw settings smaller than 1 × 1 cm, measured dose can be considerably smaller than Eclipse predicted dose, even with the OF Table extension. This is reflected by the fact that the output factor for 0.5 × 0.5 cm, calculated via Eclipse external beam, was more than 30% greater than that measured for both 6FFF and 6MV beams. Conclusions: Eclipse does a satisfactory job for primary jaw sizes down to 2 cm. For jaw settings smaller than 1.5 cm, the OF Table in Eclipse should be extended to improve the dose calculation accuracy. [ABSTRACT FROM AUTHOR]

Sensitive and fast detection of neutrons and gamma rays is vital for homeland security, high‐energy physics, and proton therapy. Fast‐neutron detectors rely on light organic scintillators, and γ‐ray detectors use heavy inorganic scintillators and semiconductors. Efficient mixed‐field detection using a single material is highly challenging due to their contradictory requirements. Here we report hybrid perovskites (C8H12N)2Pb(Br1−xClx)4 that combine light organic cations and heavy inorganic skeletons at a molecular level to achieve unprecedented performance for mixed‐field radiation detection. High neutron absorption due to a high density of hydrogen, strong radiative recombination within the highly confined [PbX6]4− layer, and sub‐nanometer distance between absorption sites and radiative centers, enable a light yield of 41 000 photons/MeV, detection pulse width of 2.97 ns and extraordinary linearity response toward both fast neutrons and γ‐rays, outperforming commonly used fast‐neutron scintillators. Neutron energy spectrum, time‐of‐flight based fast‐neutron/γ‐ray discrimination and neutron yield monitoring were all successfully achieved using (C8H12N)2Pb(Br0.95Cl0.05)4 detectors. We further demonstrate the monitoring of reaction kinetics and total power of a nuclear fusion reaction. We envision that molecular hybridized scintillators open a new avenue for mixed‐field radiation detection and imaging. [ABSTRACT FROM AUTHOR]

Inorganic perovskite quantum dots CsPbX3 (X = Cl, Br, and I) has recently received extensive attention as a new promising class of X‐ray scintillators. However, relatively low light yield (LY) of CsPbX3 and strong optical scattering of the thick opaque scintillator film restrict their practical applications for high‐resolution X‐ray microscopic imaging. Here, the Ce3+ ion doped CsPbBr3 nanocrystals (NCs) with enhanced LY and stability are obtained and then the ultrathin (30 µm) and transparent scintillator films with high density are prepared by a suction filtration method. The small amount Ce3+ dopant greatly enhances the LY of CsPbBr3 NCs (about 33 000 photons per MeV), which is much higher than that of bare CsPbBr3 NCs. Moreover, the scintillator films made by these NCs with high density realize a high spatial resolution of 862 nm thanks to its thin and transparent feature, which is so far a record resolution for perovskite scintillator‐based X‐ray microscopic imaging. This strategy not only provides a simple way to increase the resolution down to nanoscale but also extends the application of as‐prepared CsPbBr3 scintillator for high resolution X‐ray microscopic imaging. [ABSTRACT FROM AUTHOR]

A special group of luminescence materials are scintillators for thermal neutron detection. Due to the properties of neutrons (contrary to e.g. electrons or gamma photons), a different approach has to be utilized—the high content of atoms with the sufficient absorption cross‐section toward neutrons and lower material density are needed. This work pursues a basic study of LiSrBO3 and LiSr4(BO3)3 doped with cerium or europium—materials promising as thermal neutron scintillators. These borates exhibit promising properties such as the high content of lithium and boron, suitable density, and proper environment for luminescent ions. Radioluminescence of these ceramic borates doped with cerium and europium was examined and promising samples were further characterized by photoluminescence spectroscopy and radioluminescence and photoluminescence kinetics measurement. The radioluminescence study of these borates is published for the first time. Cerium‐doped borates, in particular, exhibit a very promising response to an X‐ray excitation. [ABSTRACT FROM AUTHOR]

Purpose: Detector arrays and profile‐scans have widely replaced film‐measurements for quality assurance (QA) on linear accelerators. Film is still used for relative output factor (ROF) measurements, positioning, and dose‐profile verification for annual Leksell Gamma Knife (LGK) QA. This study shows that small‐field active detector measurements can be performed in the easily accessed clinical mode and that they are an effective replacement to time‐consuming and exacting film measurements. Methods: Beam profiles and positioning scans for 4‐mm, 8‐mm, and 16‐mm‐collimated fields were collected along the x‐, y‐, and z‐axes. The Exradin W2‐scintillator and the PTW microdiamond‐detector were placed in custom inserts centered in the Elekta solid‐water phantom for these scans. GafChromic EBT3‐film was irradiated with single uniformly collimated exposures as the clinical‐standard reference, using the same solid‐water phantom for profile tests and the Elekta film holder for radiation focal point (RFP)/patient‐positioning system (PPS) coincidence. All experimental data were compared to the tissue‐maximum‐ratio‐based (TMR10) dose calculation. Results: The detector‐measured beam profiles and film‐based profiles showed excellent agreement with TMR10‐predicted full‐width, half‐maximum (FWHM) values. Absolute differences between the measured FWHM and FWHM from the treatment‐planning system were on average 0.13 mm, 0.08 mm, and 0.04 mm for film, microdiamond, and scintillator, respectively. The coincidence between the RFP and the PPS was measured to be ≤0.5 mm with microdiamond, ≤0.41 mm with the W2‐1 × 1 scintillator, and ≤0.22 mm using the film‐technique. Conclusions: Small‐volume field detectors, used in conjunction with a clinically available phantom, an electrometer with data‐logging, and treatment plans created in clinical mode offer an efficient and viable alternative for film‐based profile tests. Position verification can be accurately performed when CBCT‐imaging is available to correct for residual detector‐position uncertainty. Scans are easily set up within the treatment‐planning‐system and, when coupled with an automated analysis, can provide accurate measurements within minutes. [ABSTRACT FROM AUTHOR]

Scintillators, which can convert high‐energy ionizing radiation into visible light, have been serving as the core component in radiation detectors for more than a century of history. To address the increasing application demands along with the concern on nuclear security, various strategies have been proposed to develop a next‐generation scintillator with a high performance in past decades, among which the novel approach via structure control has received great interest recently due to its high feasibility and efficiency. Herein, the concept of "structure engineering" is proposed for the exploration of this type of scintillators. Via internal or external structure design with size ranging from micro size to macro size, this promising strategy cannot only improve scintillator performance, typically radiation stopping power and light yield, but also extend its functionality for specific applications such as radiation imaging and therapy, opening up a new range of material candidates. The research and development of various types of structured scintillators are reviewed. The current state‐of‐the‐art progresses on structure design, fabrication techniques, and the corresponding applications are discussed. Furthermore, an outlook focusing on the current challenges and future development is proposed. [ABSTRACT FROM AUTHOR]

Sensitive and fast detection of neutrons and gamma rays is vital for homeland security, high‐energy physics and proton therapy. However, efficient mixed‐field detection using a single material is highly challenging because fast‐neutron detectors rely on light organic scintillators, and γ‐ray detectors use heavy inorganic scintillators and semiconductors. In the cover, the authors (DOI: 10.1002/inf2.12325) illustrate organic‐inorganic hybrid perovskites that combine light organic cations and heavy inorganic skeletons at a molecular level to achieve unprecedented performance for mixed‐field radiation detection, so as to obtain the time information and energy information of the nuclear reaction process accurately. [ABSTRACT FROM AUTHOR]