Search

Conventional drilling of carbon fibre–reinforced plastic (CFRP) presents significant challenges due to the material's abrasive nature and anisotropic properties, leading to tool wear, delamination, and surface damage. To address these challenges, this study pioneers the use of wire electrical discharge machining (WEDM) to evaluate the drilling performance of thick CFRP lay-up configurations mainly unidirectional and multidirectional, marking the first application of WEDM for CFRP drilling. The study evaluates material removal rate (MRR), delamination factor (DF), and surface damage while employing an analytical solution to estimate surface temperature and heat conduction in the laminates. An eight-full factorial experimental design was employed, involving variations in ignition current (3 A and 5 A) and pulse-off time (4 µs and 8 µs). The findings revealed that the multidirectional lay-up achieved an MRR of 2.85 mm3/min, significantly outperforming the unidirectional lay-up's MRR of 0.95 mm3/min, representing a 300% increase at 5 A and 4 µs. However, the increase in discharge energy led to surface damage such as delamination, frayed fibres, and irregular circularity, especially evident in the unidirectional lay-up. For delamination, the multidirectional lay-up had the highest top DF of 1.4 at 5 A and 6 µs, while the unidirectional lay-up achieved the peak bottom DF of 1.24 at the same levels. While none of the parameters significantly affected the responses, the current exhibited the highest contribution ratios. Analytical predictions of the thermal distribution indicated a 45-µm delamination length at the laminate surface and depth, aligning closely with experimental predictions of 30–50 µm. [ABSTRACT FROM AUTHOR]

Ti-6Al-4V alloy due to high mechanical properties and high corrosion resistance is widely used in the manufacture of biomedical devices, including hip articulations, screws and dental implants. For proper implant performance in the long run, a rapid reaction between the bone and implant should be performed, which depends on the surface properties of the layer doped on the surface of the implant. The surface coating is therefore considered to be the underlying factor in the attenuation of such occurrences. This research aims to assess the modified surface of Ti-6Al-4V by the mixed electric discharge (EDM) process of β-tricalcium phosphate powder to detect potential bioimplants. One of the features of this coating process is the location of the base titanium layer containing β-tricalcium phosphate, thereby improving the substrate properties. For investigating the surface morphology, distribution and dispersion of elements on the modified surface, field emission scanning electron microscope (FE-SEM), energy-dispersive x-ray spectroscopy (EDS) and x-ray diffraction (XRD) tests were used. Morphological features have shown that porous surface topography just like natural bone is coated on the surface of Ti-6Al-4V alloy using the AM-EDM process. EDS and XRD examinations showed the coated layer compositions from Ti kα, V, Al, Ca and P and also formation of the biocompatible phases such as Ca 2 P 2 O 7 andCa OH 2 on the surface of Ti-6Al-4V, which caused the better biocompatibility of the alloy, creation of an antibacterial agent for periodical injuries and also improvement of the bone formation on the alloy surface. The results also showed that the size of the resin thickness was 35 micrometers, which contained nanoparticles of tricalcium phosphate, as well as an excellent metallurgical substrate with a strong bond between the substrate and the coating. In this research, the effects of input parameters, such as spark energy and powder concentration on output parameters, including material removal rate, surface roughness and surface hardness, were studied. The results showed that this method has a positive effect on the reduction in the material removal rate, roughness and hardness of the surface of the workpiece. Due to the dispersion of β-tricalcium phosphate particles, the surface roughness diminishes during the electric discharge process. Also, the highest material removal rate occurred in 21 A, the pulse duration of 50 μs and the concentration of 8 g/L, and minimal surface roughness occurred in 6 A, the pulse duration of 100 μs and the concentration of 4 g/L. The hardness of the surface deposited with β-tricalcium phosphate powder is 348 VH, which is 1.75 times more than the original surface. The reason is that the hard oxide is deposited on the surface of the workpiece. [ABSTRACT FROM AUTHOR]

Sustainability is vital in manufacturing industries for the fabricating products with economic, social and environmental attention. The current study uses stir casting fabricating methodology to manufacture aluminium LM25 alloy reinforced with 7.5 wt.% Silicon Carbide (SiC) and 2.5 wt.% Titanium Oxide (TiO2) hybrid metal matrix composite (HMMC). The microstructural and energy dispersive spectroscopy (EDS) analysis is supported to confirm hybrid reinforcement's existence and even distribution in the aluminium matrix. The Vicker's hardness of 110.25 HV is measured for the manufactured composite. The machinability behaviour of the fabricated HMMC is studied using electrical discharge machining (EDM) to achieve the optimum material removal rate (MRR) and surface roughness (SR) through Taguchi integrated grey relational analysis (TGRA). To get the best machining results, the impact of machining process variables such as pulse on time (Ton), current (I), and voltage (V) was examined. To determine the importance of process variables on the machining responses, analysis of variance (ANOVA) was also conducted. The optimum machining process variables were revealed concerning the machining process variables such as pulse on time 100 μs, current 6 A, and voltage 25 V. ANOVA analysis confirmed that the current with a percentage significance of 71.52%, is the most important EDM machining process variable followed by pulse on time and voltage. Further, the machined surface is examined through a hi-resolution scanning electron microscope (HRSEM) and 3D optical profilometer. The formation of a white layer, craters and bubbles on the machined area are observed for varying machining conditions. The fabricated HMMC can be utilized in the automobile applications such as pistons, brake discs, gears and cylinders. [ABSTRACT FROM AUTHOR]

In the electrical discharge machining process (EDM), quantities of discharge craters randomly scatter the workpiece surface. However, the formation mechanism of the discharge crater has not been fully understood, which affects the application of EDM technology. In the paper, a thermal-fluid coupling model was proposed to elucidate the crater formation dynamics process utilizing COMSOL Multiphysics software. The temperature distribution, fluid flow velocity, and more changes in the crater were analyzed, aiming to deepen the understanding of the formation mechanism of the discharge crater in the EDM process. Through the comparison of experimental results and numerical simulation results, it was found that a little of the material is eroded by vaporization, while a lot of material is eroded mainly by melting. In addition, the material removal process is continuously eroded after the end of discharge due to the residual heat and the flow of molten material. Moreover, the effect of pulse on-time and peak current on the temperature field and flow field was solved. Through the experiments and numerical simulations, it was shown that the simulation results are consistent with the experimental results, verifying the applicability of the thermal-fluid coupling model in demonstrating the mechanisms of crater formation in the EDM process. [ABSTRACT FROM AUTHOR]

Electrical discharge grinding technology (EDGT) is an efficient and high precision method for machining RB-SiC ceramic materials. In this paper, the mechanism of material removal in EDGT is deeply analyzed, and the formation mechanism of surface topography under different material removal regimes affected by grinding depth is discussed. A three-dimensional heat conduction analysis model in the process of single pulse discharge was established, and the temperature field distribution in RB-SiC ceramic material under different discharge energy was obtained by numerical calculation. It is found that the simulated crater radius and depth increase with the increase of the discharge time, and the material removal amount gradually increases, but the growth rate gradually decreases. In order to give full play to the advantages of EDGT, the discharge energy and grinding depth were optimized according to the material removal mechanism. Finally, RB-SiC ceramic machining experiments were carried out using the optimized machining parameters, and a smooth surface with few discharge craters was obtained. It is found that the grinding scratches on the material surface are mainly plastic grinding, and the material surface roughness is 0.443 μm. The research results of this paper can provide guidance for engineering practice of ductile grinding RB-SiC ceramic materials. [ABSTRACT FROM AUTHOR]

Electrode wear (EW) during the electrical discharge machining (EDM) process determines surface topography accuracy. In this paper, an automatic evaluation method is proposed by integrating image segmentation and three-dimensional (3D) registration (IS-3DR) to evaluate the EW more accurately. First, the original two-dimensional (2D) image and the 3D point cloud were derived from a laser microscope image, and the 2D worn area was determined by automatic recognition and segmentation. Then, 3D registration between the 3D point cloud and the 2D worn area was utilized to qualitatively define the 3D EW area. Finally, the 3D EW volume was obtained quantitatively through micro-element calculation based on the 3D EW area and the shape fitting of the original electrode. The results showed that the intersection over union (IOU) of image segmentation was higher than 97.5%, compared with the manually labeled image segmentation method. Compared with IS-3DR, the random error of the two-dimensional evaluation method could reach 27.08%, indicating higher reliability and stability of IS-3DR. The EDM experiment was carried out to investigate the effect of parameters on EW. The experimental results showed that the effects of current and servo voltage were most significant, followed by pulse width. [ABSTRACT FROM AUTHOR]

In electrical discharge machining (EDM), it is a much more effective method to improve working characteristics by changing the input process of pulse energy. However, it has not been investigated enough whether pulse form is the most adequate or not. In this study, the effect of superimposed pulse current waveform and its parameter on surface integrity was investigated. The surface topography, roughness, microstructure, white layer thickness, and residual stress were analyzed and discussed. Moreover, the material removal rate was also tested and compared. The results show that with the backward movement of the superimposed pulse current, the material removal rate and surface roughness decrease, while the white layer thickness, residual stress, and surface defects increase. The current waveform has little influence on microstructure. Under the same pulse discharge energy and pulse-on time, the samples processed by superimposed pulse current waveform instead of rectangular current waveform can obtain a thinner white layer, lower residual stress, fewer surface defects, and high surface roughness. With the increase of superimposed pulse-on time and current, the surface integrity becomes worse due to the increase of pulse energy. This paper provides a guide to the development and selection of EDM discharge current waveforms in EDM. [ABSTRACT FROM AUTHOR]

Micro electrical discharge drilling (ED-drilling) is a machining method used to make micro holes in hard-to-cut materials. The RC-discharge generator is often used because it creates a short and strong discharge spark. However, this method has issues such as current oscillation between tool electrode and workpiece, causing polarity changes that increase tool wear, and a low material removal rate due to long spark delay time. Furthermore, micro ED-drilling results in a large taper angle due to second discharge sparks created by debris in the narrow gap. To address these issues, the effect of adding graphite powder to the working fluid was studied. The graphite powder in kerosene created a bridge effect that reduced tool wear and taper angle, while improving MRR and surface roughness. The electrical conditions were not changed, and the machining process was improved by only altering the working fluid without modifying the existing system. [ABSTRACT FROM AUTHOR]

Electrical discharge drilling of blind holes has been a challenging task due to the inherent difficulties in removing debris from the discharging gap. This paper investigates the working mechanism and effects of new stepped electrodes which are used in conjunction with injection flushing in drilling deep blind holes. A series of theoretical simulations and comparative experiments were conducted using cylindrical electrodes and two types of stepped electrodes. Pulse waveforms were captured to analyse the discharge status. Surface topography and machining quality were analysed using scanning electron microscope (SEM) images. The machining performance was evaluated by studying the material removal rate (MRR) and tool wear ratio (TWR). Experiment results show that internal flushing caused the debris to circulate in the machining zone and led to abnormal discharges, disrupting the formation of the plasma channel. The MRR was increased by 75% and 82% when using cylindrical electrodes with pressures of 120 psi and 40 psi, respectively. In contrast, the MRR with injection flushing was about 80% of that without injection flushing when using stepped electrodes. Regardless of the type of electrode, the application of injection flushing resulted in the increase in the maximum effective machining depth. [ABSTRACT FROM AUTHOR]

A global manufacturing community is dedicatedly striving to implement the concept of NetZero in precision cutting of difficult-to-machine materials, specifically, Inconel 617 (IN617) with due consideration to environmental protocols. The fast strain hardening issue of the said alloy during conventional processing rationalizes the application of electric discharge machining (EDM). However, EDM has been criticized for its high energy consumption and limited cutting efficiency. Moreover, conventional dielectric (kerosene) employed in EDM has drastic environmental and operator health concerns. To address the abovementioned issues, waste cooking oil (WCO) has been employed in this study which enhances the reusability of resources and minimizes the cost of the dielectric. Making the process sustainable is imperative along with continuously escalating scarcity of engineering resources. Therefore, the potential of shallow and deep cryogenically treated electrodes (SCT and DCT) has been comprehensively examined against nanofilled WCO to achieve the aforementioned objective. Three different concentrations of powder (Cp) and surfactant (Cs) to uplift the machining responses are investigated through a detailed parametric experimental design. Core machining factors such as material removal rate (MRR), surface roughness (SR), and specific energy consumption (SEC) are examined through optical and electron microscopy studies and 3D surface profilometry. Hereafter, machining factors are modelled using the artificial neural network (ANN) technique. An exceptional improvement of 80%, 25.3%, and 75.16% has been achieved in MRR, SR, and SEC respectively using nanopowder-mixed WCO against SCT brass compared to the responses' values obtained against conventionally used kerosene. Furthermore, compared to kerosene, the maximum CO2 reduction of 79.97 ± 11.2% is achieved with WCO. [ABSTRACT FROM AUTHOR]

The use of additive technology—in particular, selective laser melting (SLM)—in producing wire electrodes for electrical discharge machining is considered. By this means it is possible to produce electrodes of high precision and complex geometry, with distinctive properties. In addition, the results of topological optimization in electrode design are presented. Topological optimization permits the production of wire electrodes that are more efficient in the given operating conditions. It is shown that, on the basis of additive technology and optimized electrode geometry with internal supply channels for dielectric liquid, the removal of sludge from the machining area may be improved, with consequent stabilization of the machining process. [ABSTRACT FROM AUTHOR]

Understanding and optimizing mechanical manufacturing processes is essential for sustainable industrial development. Among unconventional machining methods, electrical discharge machining (EDM) distinguishes itself by its capability to remove material through successive electrical discharges submerged in a dielectric fluid. EDM encompasses intricate phenomena influenced by machine parameters, dielectric choice, and the materials involved. Unlike conventional machining, EDM operates with the tool electrode in close proximity to, but not in physical contact with, the workpiece, achieving material removal through localized overheating. This study focuses on monitoring EDM phenomena during the machining of AISI H13 steel, exploring variations in machining parameters and electrode materials (electrolytic copper and graphite). Acoustic emission (AE) signals and machine learning (ML) are employed for experimental characterization and data analysis. Spectral entropy is applied to AE signals, quantifying inherent signal uncertainty. The findings reveal remarkable accuracy (97.7%) and underscore the superior control achieved with graphite electrodes in managing machining phenomena compared to electrolytic copper electrodes. [ABSTRACT FROM AUTHOR]

When utilizing electrical discharge machining (EDM) for processing, the processing efficiency and quality will be significantly impacted, if the electrocorrosion residues in the gap flow field cannot be discharged in time. Numerical simulation is considered an effective means to simulate the flow field of EDM gaps. Based on simulation, this study investigates the processing time, depth, current, and dielectric (kerosene, water, and sunflower seed oil), on the movement of electrocorrosion residues within the dielectric. The simulation results demonstrate that an increase in processing time, current, or depth leads to a decrease in the escape rate of corrosion residues from the discharge gap. Compared with kerosene and sunflower seed oil, water has a higher residue escape rate, but the actual processing effect is not ideal. The escape rate of sunflower seed oil at any time was higher than that of kerosene,the highest was higher than 25%, and the average was higher than 22.21%. Sunflower seed oil can be used as a renewable dielectric to replace kerosene. Subsequently, verification experiments are conducted based on simulation results that demonstrate that the discrete phase model (DPM) fluid simulation exhibits excellent coupling with actual processing conditions. [ABSTRACT FROM AUTHOR]

Electrical discharge machining (EDM) and electrochemical machining (ECM) are two typical unconventional processing methods for fabricating difficult-to-cut materials. Surfaces machined by EDM generally contain recast layers, whereas ECM owns low machining accuracy. EDM–ECM hybrid machining can suppress their shortcomings and combine their advantages. The working fluid is vital to realizing the combination of EDM and ECM. Conventional EDM–ECM hybrid machining commonly adopts water-based fluid, which can meet the requirements of hybrid micro-, small-hole, and milling machining. However, water-based fluid hardly maintains the stable sinking EDM that possesses a relatively large machining area and a closed machining gap; thus, it is unsuitable for hybrid sinking machining. The lack of appropriate fluid seriously hinders the promotion and application of EDM–ECM hybrid sinking machining. Here, a novel bi-characteristic fluid water-in-oil (W/O) nanoemulsion that combines electrical insulation and conductive properties is proposed, and an electrical discharge and electrochemical hybrid sinking machining (EDCSM) using W/O nanoemulsion is developed. The composition parameters (salt concentration, water content) of the W/O nanoemulsion and electric parameters (open voltage, pulse frequency) are investigated. Material removal mechanisms are also discussed. Results show that the material removal mechanisms and the strength of EDM and ECM in EDCSM can be manipulated by adjusting the investigated crucial parameters. EDCSM using W/O nanoemulsion can achieve a high-quality machined surface and good machining accuracy, demonstrating its superiority and potential in the field of sinking machining. [ABSTRACT FROM AUTHOR]

The electrode is an important component of electrical discharge machining (EDM), playing an important role in machining efficiency, surface quality and geometric accuracy. In this work, a new method combining equal channel angular pressing (ECAP), deep cryogenic treatment (DCT) and aging treatment (AT) was proposed. The ultrafine-grained Cu-0.5%Cr electrode has high strength and high electrical conductivity through this process, so as to improve the machining characteristics in EDM. The surface roughness (Ra), the workpiece corner sharpness (WCS), and the electrode wear rate (EWR) were investigated. The results showed that the treatment of the electrode with 4 passes of ECAP + DCT (12h) + AT (550℃ × 1h) can reduce the EWR and WCS by 63.6% and 49.7%, respectively. It also contributed to the enhancement of electrical conductivity and microhardness of the Cu-0.5%Cr electrode by ECAP + DCT + AT. Meanwhile, it revealed that the processing of the Cu-0.5%Cr electrode resulted in the excellent machined surface quality (Ra was reduced by 53.5%) which was confirmed by the results of the scanning electron microscopy (SEM). The ultrafine-grained Cu-0.5%Cr electrode with an excellent combination of strength and electrical conductivity has an outstanding EDM performance. [ABSTRACT FROM AUTHOR]

The titanium alloy Ti6Al4V ELI (grade 23) is widely used in biomedical industry because of its engineering attributes. However, it requires surface modifications and has processing challenges because it is difficult to machine nature. Therefore, powder-mixed electric discharge machining process is commonly applied to simultaneously machine the material and carry out surface treatment. The performance of the process is limited by both low cutting efficiency and the formation of a rough surface. In this regard, the current study evaluates SiC powder-mixed electric discharge machining of Ti6Al4V ELI using a range of tool materials such as copper, brass, graphite, and aluminum along with a comprehensive list of process parameters. The surface roughness parameters involving arithmetic roughness, the average peak-to-valley distance, and the highest peak-to-deepest valley distance along with material removal rate are comprehensively studied. Taguchi design of experiments L16 orthogonal array is used to study the process performance with parametric effect analysis, parametric significance analysis, and surface morphological analysis with a scanning electron microscope. Furthermore, the experimental results are optimized against a multi-response optimization matrix using grey relational analysis approach. An optimal compromise between surface attributes and cutting efficiency is identified by Al electrode, pulse current of 14 A, pulse on time of 75 µs, pulse off time of 75 µs, and negative polarity parametric conditions. [ABSTRACT FROM AUTHOR]

Metallic glass offers several advantages, including high strength, corrosion resistance, and low coercivity. In precision machining fields like optical devices, medical devices, and micro-electromechanical systems, Ti-based metallic glass offers more advantages than Fe- and Zr-based metallic glass. However, its current machinability poses a challenge in meeting the requirements of precision metallic glass parts. To obtain the best machining performance, a thermophysical model of the EDM drilling process was established to simulate the temperature distribution on the surface of metal glass workpiece during EDM drilling. In addition, a new systematic method is utilized to calculate the characteristics of important machining holes, such as inlet and outlet overcut and inlet and outlet edge deviation. In this investigation, the maximum relative overcut and edge deviation are 8.59% and 7.23%, respectively, relative to the electrode radius. To improve the machining quality and machining stability, the slit width should be kept at an ideal value. Therefore, the recommended discharge current is 4–5 A, pulse duration is 50 μ s, and pulse duty ratio is 0.2 - 0.3 when EDM drilling of amorphous alloy. Based on this, the EDM drilling analysis method by numerical and experimental investigation for titanium-based metallic glass is put forward, which provides scientific theoretical guidance for the EDM of drilling it. [ABSTRACT FROM AUTHOR]

High-intensity electrical discharges are used in the unconventional technique known as electrical discharge machining (EDM) to machine metals of any hardness. Due to their extraordinary conductivity and strength, carbon nanotubes (CNTs) have recently been explored in EDM too. However, material removal with CNT yarn (CNTY) has not been studied thoroughly. This work advocates the use of a pristine CNTY as an EDM tool. The feasibility is examined through characterization and material removal experiments. The measurements show that the CNTY (< 100 µm in diameter) has an electrical conductivity and current carrying capacity of 2.66 × 104 S/m and 1.76 × 103 A/cm2, respectively. Steel and aluminum are the workpieces for machining experiments conducted in air and hydrocarbon oil dielectrics, respectively. Significant material removal and extended tool life are obtained in the air dielectric. It is suggested that the oxidation of steel increases material removal in the air while reducing tool life. The effect of tool thickness is also investigated. Thicker (> 100 µm) multi-ply tools extend tool life and, therefore, machining time by more than 14 s in the air and nearly 2.5 s in the oil. Other factors that restrict machining include intensified discharges and the shielding effect of the carbide layer formed on the workpiece. [ABSTRACT FROM AUTHOR]

Aluminum alloys with 40 to 50 wt.% silicon content are potential material candidates for the manufacturing of satellite components. These materials have excellent thermal and mechanical stabilities, but machining complex components from these alloys is facing many challenges. The present study was performed on an aluminum-high silicon alloy (50–50 wt.%) with the main aim of investigating the evolution of the microstructure with particular attention to surface and subsurface damage as a result of Electrical Discharge Machining (EDM). For this purpose, the microstructure was characterized by optical and Scanning Electron Microscopes (SEM) as well as Energy Dispersive Spectroscopy (EDS) of the machined samples. The results show the existence of melted and re-solidified zone with much finer silicon particles located in a zone on the top of the machined surface where cracks were also observed. Moreover, SEM examinations showed that the cracking damage concern the primary silicon particles. Possible mechanisms, such as the thermal shock produced by rapid cooling rate of the primary silicon particles and the presence of porosities, formed during the manufacturing process, are discussed. [ABSTRACT FROM AUTHOR]

Due to different characteristics of ceramic coatings and superalloy substrates, it is impossible to balance surface quality and machining efficiency of thermal barrier coated superalloys by using constant parameters in electrical discharge machining. In this paper, an adaptive control (AC) method is studied, which can adaptively adjust discharge parameters in real time according to the change of material types. A short circuit detection method based on statistics of the duration of the current falling edge is proposed. And by combining it with voltage detection, discharge states of high resistance and low resistance can be both identified. Based on statistics and analysis of discharge waveforms under various discharge states, a detection method is studied to distinguish metals from insulating ceramics. An adjustment strategy of parameters that has higher sensitivity to insulating ceramics is proposed. It can ensure the real-time conversion of parameters and reduce the number of high-energy pulses acting on the ceramic surface. The waveforms of discharge gap measured with an oscilloscope show that the AC method can realize the conversion between low energy pulses and high energy pulses. The experimental results show that the AC method has much shorter machining time (5.1 min) compared with the method of small energy parameters (52 min) and has smaller maximum damage distance (58.4 μm) than the method of large energy parameters (89 μm). [ABSTRACT FROM AUTHOR]

Traditional electric discharge machining (EDM) uses a Cu electrode to machine polycrystalline diamond (PCD), but it is hampered by poor machining efficiency and quality. During this study, a Cu-Ni electrode was used to machine PCD with graphene power suspended in the dielectric. The surface properties and machining mechanism of PCD under different parameters were analyzed by scanning electron microscope (SEM), X-ray diffraction (XRD), and Raman spectroscopy. The surface quality and machining efficiency were analyzed by quantifying the surface roughness (SR) and material removal rate (MRR). The results demonstrated that the MRR of the Cu-Ni electrode increased by 65% when compared with that of Cu electrode at low discharge parameters, with the MRR of Cu-Ni electrode improved by a further 87% when graphene was added to the dielectric. Raman spectroscopy and XRD analysis showed that graphitization of PCD diamond processed by the Cu-Ni electrode was greater than that of the Cu electrode, and the addition of graphene further facilitated this process. The machining efficiency and quality of PCD in EDM can be greatly improved with the use of Cu-Ni electrode and graphene suspended in the dielectric. [ABSTRACT FROM AUTHOR]

A computer-aided manufacturing system for the production of cutting inserts made of advanced tool ceramics by the method of electrical discharge machining (EDM) has been developed. The system is based on the established relationships between the workpiece properties, precision requirements and EDM modes. [ABSTRACT FROM AUTHOR]

The efficiency and accuracy of conventional electrical discharge machining (EDM) are limited by the stability of the voltage between the poles. To improve the efficiency of EDM, this paper presents a machining method that combines a self-developed 5-degree-of-freedom (5-DOF) controllable magnetic levitation actuator with a conventional EDM machine tool. The stability of the interpole voltage is improved by actuator microadjustment of the electrodes of the EDM machine tool. First, an EDM control system with local current feedback and decoupling control elements is designed based on the EDM servo drive principle to improve the response speed and positioning accuracy of the actuator. Second, the actuator is connected to the spindle of a conventional EDM machine tool, and machining experiments are carried out. The experimental results show that the EDM machine tool connected to the actuator can control the electrode position more quickly, adjust the discharge state quickly, and increase the number of discharges per unit time. The average machining speed increases from 1.108 to 3.925 µm/s, which is 3.54 times as fast as conventional EDM. Finally, complex shape machining experiments are carried out, and the machining results showed that by adjusting the target value of the radial direction of the actuator, the various trajectories of the electrode can be controlled to depict arbitrary shapes. [ABSTRACT FROM AUTHOR]

Inconel 625 superalloy and stainless steel 304 are known for their significant corrosion resistance along with their high hardness and strength. Therefore, they are used in a wide range of industries, including oil and gas and nuclear. Electrical discharge machining is among the most widely used processes for machining of these metals. However, this process has limitations, such as low material removal efficiency, high surface roughness, and the formation of a recast layer. Therefore, in this study, the effective parameters on increasing the material removal efficiency and reducing recast layer thickness are investigated. These parameters include the dielectric fluid, electrode material, discharge current, and pulse duration. After performing the test matrix, the effect of each of the input parameters on the material removal rate, surface roughness, and thickness of the recast layer is evaluated using the ANOVA method. The results of this analysis showed that the type of dielectric fluid and the presence of silver oxide nanoparticles have a significant effect on output variables. When using sunflower oil fluid containing nanoparticles and the silver electrode, the recast layer and surface roughness are reduced, while the average material removal rate increases by 40% compared to the traditional mode. Also, due to the biodegradability of deionized water and sunflower oil fluids, the environmental sustainability of the process in this study is increased and while increasing productivity, it leads to the sustainable development of the EDM process. [ABSTRACT FROM AUTHOR]

The influence of surface plasma treatment on the aging of 12Х18Н10Т steel in a long loading cycle is investigated. Great changes are observed in samples produced by rough electrical discharge machining (EDM). Almost all the samples obtained by this method fail. The use of lower current increases the cyclic life of the workpiece. Samples obtained by rough electrical discharge machining in copying and piercing modes fail after 1.5 × 106 cycles in gigacycle fatigue tests. By contrast, samples obtained in finishing fail after 3.5 × 106 cycles. [ABSTRACT FROM AUTHOR]

Electrical discharge machining (EDM) is a well-known manufacturing process that is reported for several times as an effective technique for cutting of nickel-based superalloy of Inconel 718 (IN718). A majority of existing researches in EDM of Inconel 718 are focused on machinability of material considering production rate, tool wear, surface roughness and dimensional tolerances. To the best of author's knowledge, corrosion resistance EDMed Inconel 718 has hardly been taken into consideration. In the present work, an experimental study was made to understand how the electrical discharge machining parameters, viz. pulse current, pulse on time and rotational motion of the tool electrode, influence the corrosion properties of IN718. Technique of potentiodynamic polarization curve was utilized to measure IC and EC of the samples. A number of seven samples were machined using single-factor experiments design, and the effect of EDM parameters on foresaid corrosion indices was studied. Surface roughness, surface morphology, hardness and residual stress distributions were taken into account for justification of the variations. It was obtained from the results that as a result of increase in current from 5 to 15A, the corrosion rate increases, where the current density increases from 0.15 to 0.28 μA/cm2, and corrosion potential decreases from 0.51 to − 2.49 VSCE. In addition, it was found that less value of pulse on time, i.e., 600 μs, results in best corrosion properties where increase up to 800 μs results in increase in corrosion density from 0.11 to 0.19 μA/cm2 and also reduction of corrosion potential from −0.34 to −1.13 VSCE. It was further found that increase in tool rotational speed from stationary condition up to 200RPM results in enhancement of corrosion resistance; here, the current density reduces from 0.4 to 0.088 μA/cm2 and increase in corrosion potential from − 1.89 to 0.11 VSCE. [ABSTRACT FROM AUTHOR]

Shape Memory Alloys (SMAs) have various applications in the field of medical science due to its superior properties such as pseudoplasticity, shape memory effect, biocompatibility, high specific strength, high corrosion resistance, high wear resistance and high anti fatigue property. The machining of TiNi shape memory alloys by traditional processes is very crucial due to poor thermal conductivity, poor surface finish and burr formation. Hence, to overcome these problems the non-conventional machining process viz. water jet machining, electrical discharge machining, laser beam machining, etc. are more suitable to machine SMAs. The appropriate non-conventional machining process EDM/wire EDM, provides better machining and surface characteristics during machining of SMAs. The objective of the current work is to identify the research gap for SMAs during their machining by the EDM and Wire EDM process and to identify the future prospective of SMAs for different applications in the field of biomedical. [ABSTRACT FROM AUTHOR]

The dies and molds made up of higher strength materials with complex shape can be easily machined using unconventional machining processes. The surface roughness and machining productivity during roughing phase has a very significant effect on increasing the efficiency of electrical discharge machining process. The optimization approach can enhance the mechanism of the machining process. In the present study, data envelopment analysis based ranking method was utilized to apply the multi criteria decision making in the process on machining SKD61 die steel. The influence of the input process factors such as voltage, pulse current and pulse-on-time were considered as input indicators in electrical discharge machining process. The material removal rate and surface roughness were selected as performance measures under rough mode to enhance the machinability in the process. From the experimental study, it was found that material removal rate and surface roughness were significantly improved under the optimal process parameter combinations of voltage (90 V), current (10 A) and pulse-on-time (100 µs). The optimal combination could produce 5% higher material removal rate with better surface finish. The surface quality of the surface layer can be improved under optimal parameters with lower white layer thickness owing to its importance on evaluating spark energy. [ABSTRACT FROM AUTHOR]

The present work aims to study the influence of adding nano graphene powder in dielectric on the circularity and surface roughness of nickel super alloy (Inconel 718) during electrical discharge machining (EDM). The mixing of suitable powder in nano form with dielectric oil enhances the machining efficacy of EDM by altering the electric field intensity and energy distribution. The experimental investigations were performed using Taguchi L27 orthogonal array by considering peak current (Ip), pulse on time (Ton) and pulse off time (Toff) as input variables. The optimal process conditions have been determined using efficient intelligent methods namely fuzzy logic and ANFIS model giving excellent prediction of machining performance in terms of surface roughness (Ra) and circularity. Based on ANFIS results, the minimum circularity and surface roughness achieved for nano graphene mixed EDM are 0.0126 mm and 1.590 µm respectively, which is 12.27% and 32.91% superior in comparison to traditional EDM results. The ANOVA analysis was performed for confirming adequacy of developed models and based on analysis, peak current was found to have most influencing effect on surface roughness with contribution of 54.96% and pulse on time proved to be the most contributing factor for circularity with contribution of 50.93%. The ANFIS model was found out to be giving more significant predictions than fuzzy model. The scanning electron microscopy shows the improvement in surface finish of nano graphene mixed dielectric EDM in comparison to traditional EDM. [ABSTRACT FROM AUTHOR]

Recent developments in material science have concentrated not only on the improvement in mechanical properties, but also on the machinability that was difficult for system profiles. The present research explains the machinability assessment of the part of the sintered powder metallurgy using an electric discharge machining. The ferrous clay matrix preparations are constructed from iron–carbon–copper material and bentonite clay. The selected input parameters for the measurement of machinability are wt. % of clay, current (A), pulse on time (µs) and voltage (V), whereas the electrode wear rate, material removal rate and surface roughness (Ra) are considered as performance features. Results show that the performance parameters have been optimized at three different parametric conditions. Further, to obtain single optimum condition the hybrid GRA-TOPSOS methodology has been implemented for maximum MRR with minimum EWR and low surface roughness. The single optimum condition has been found at 5% clay, current 7 A, voltage 49 V and pulse on time 400 µs. The study of micro-structure and chemical composition of machined surfaces has been carried out using scanning electron microscopy with X-ray diffraction and energy-dispersive spectrometry analysis, respectively. The SEM exposes the less recast layer and micro-cracks during electrical discharge machining of ferrous clay composite. [ABSTRACT FROM AUTHOR]

The discharge current waveform affects the processing characteristics and surface integrity by affecting the process of energy input. At present, although the rectangular current waveform is widely used in electrical discharge machining (EDM), there is not enough evidence to prove that it is the most suitable. Therefore, in this study, the influence of the discharge current waveforms on processing characteristics and surface integrity was investigated and compared under similar pulse energy. Three types of discharge current waveforms including rectangular (Rec), triangular (Tri), and trapezoidal (Tra) are used for processing. The material removal amount, surface topography, roughness, phase compositions, white layer thickness, and residual stress were investigated and analyzed. The results showed that Tri could remove the most materials per pulse-on duration, followed by Tra. Compared with Rec, the size of craters and debris on the sample surface produced by the Tri and Tra was larger. The surface roughness and residual stress of samples processed by Tri were the highest. When the discharge current waveform was constant, XRD spectra of samples fabricated by EDM under different pulse energy were almost the same. Compared with Rec, the diffraction peaks of samples produced by Tri and Tra were reduced. When the pulse energy was low, the white layer of samples processed by Rec was thinner than that processed by Tri. This phenomenon was reversed when the pulse energy was high. The white layer thickness of the sample fabricated by Tra was between the samples processed by Rec and Tri regardless of pulse energy. [ABSTRACT FROM AUTHOR]

Continuous electrical discharge machining (EDM) is characterized by random discharge positions, uncertain discharge energy, extremely short discharge time, extremely narrow tool-workpiece gaps, etc. Theoretical research into the mechanisms leading to thermal erosion of material and the associated surface morphology has become urgent to allow the continued development and application of EDM technology. Firstly, multi-pulse theory and geometric optimization are utilized to derive an expression for the material removal rate and surface roughness in multi-pulse EDM. Secondly, based on the characteristics of multi-pulse discharge, a multi-pulse numerical simulation model was established to predict the material removal volume, surface roughness, and thickness of the recast layer. Finally, the results predicted by the geometric and numerical models are compared with the experimental results. Experimentally, 0.176 mg of material is removed in the multi-pulse EDM; the theoretical calculation and numerical simulation of the same produce errors of 5.11% and 11.36%, respectively. The analogous results for the surface roughness are 1.623 μm, 8.93%, and 1.23%. The experimentally determined thickness of the recast layer was 5.31 μm, which corresponds to an error in the simulation error of 7.53%. [ABSTRACT FROM AUTHOR]

In electrical discharge machining (EDM), the discharge current waveform that determines the process of energy input has an important influence on machining characteristics as the discharge voltage is constant after the dielectric is broken down. In the past, the influence of pulse-on time and current on the surface metamorphic layer under rectangular current waveform has been reported, while the influence of non-rectangular current waveform on the surface metamorphic layer is still elusive. In this study, the difference in the surface metamorphic layer of the workpiece processed by triangular current waveform and rectangular current waveform under the same pulse energy was investigated and analyzed. Compared with rectangular current waveform, surface roughness of the workpiece processed by triangular current waveform was higher. Cracks on the surface of the sample produced by rectangular current waveform always exist from 0.088 to 1.96 mJ. However, it was difficult to observe cracks on the surface of the sample processed by the triangular current waveform when the pulse energy was higher than 0.41 mJ. There is no obvious difference in the intensities of diffraction peaks α-Fe, γ-Fe, and cementite for the samples processed by rectangular current waveform with different discharge energy. However, for the workpiece fabricated by triangular current waveform, the peaks of cementite and γ-Fe increased as the pulse energy increased. When the pulse energy was low, the white layer of the sample processed by rectangular current waveform was thinner than that processed by triangular current waveform. This phenomenon is reversed when the pulse energy is high. [ABSTRACT FROM AUTHOR]

The influences of electrical and non-electrical parameters on surface integrity during the EDM process have been widely researched in past years. However, the effect of the energy input process at the same discharge energy is seldom reported. To select more suitable processing parameters according to the processing requirements, we have studied the influence of the energy input process on processing characteristics and surface properties. Two different energy input modes (high discharge current with short pule-on time (HIST) and low discharge current with long pule-on time (LILT)) are used. When the discharge energy is the same, the HIST mode has a higher material removal amount, while the sample produced by the LILT mode presents a lower surface roughness and residual stress. More surface cracks are detected on the samples processed by the LILT mode, and their dimensions in terms of length and width are greater than that of the HIST mode. The microstructure of the EDM surface is composed of α-Fe, γ-Fe, and cementite. When the discharge energy is higher than 0.24 mJ, the intensities of diffraction peaks γ-Fe and cementite on the EDM workpiece surface produced by the HIST mode are higher. The white layer thickness is related to the discharge energy and its input process. When the discharge energy is lower than 0.51 mJ, the white layer is thinner under the LILT mode. However, the white layer of the EDM sample fabricated by the HIST mode is thinner when the discharge energy is higher than 0.51 mJ. [ABSTRACT FROM AUTHOR]

Electrical discharge machining (EDM) is an unconventional machining process based on removing material by successive electrical discharges. The tool electrode wear must be kept as minimal as possible to produce high-precision components. This scope proposes the development of a new technique for identifying wear on electrodes and its evolution using acoustic emission (AE) signals. Therefore, EDM tests were performed on AISI H13 steel parts with electrolytic copper tool electrodes under different conditions with concomitant AE signal measurements. In these tests, the first one has the following parameters: voltage pulse duration time (te) of 150 μs; the time interval between two successive voltage pulses (to) of 14.84 μs; electrical current of 33 A; and positive polarity electrode. For the second test: duration of the voltage pulse of 2 μs; the time interval between two successive voltage pulses of 4.90 μs; electrical current of 18 A; and negative polarity electrode. In this way, a wear rate 28.3 times higher was obtained in the electrolytic copper electrode in the first test, more aggressive due to its parameters, for the same machining time compared to the second test. Finally, the wear of the tool electrodes was related to the AE signals from machining; initially in this study, the workpiece's mass loss was not verified. These signals were analyzed using the short-time Fourier transform techniques and spectral entropy. The results showed that the signals using the new technique of relation respond to wear and are sensitive to the electrode's wear rate. [ABSTRACT FROM AUTHOR]

Electrical discharge machining (EDM) is the unconventional machining technique used extensively for machining difficult-to-machine materials with lower material removal rate and poor surface roughness. To overcome these drawbacks, synthetic dielectric fluid is replaced with nanoparticle-infused biodegradable dielectric fluid in the machining of Hastelloy material. This paper focusses on the machining performances of Hastelloy in EDM using various concentrations of 0.5, 1 and 1.5 wt% of nano-zirconia dispersed in biodegradable canola oil methyl ester as the dielectric medium, and these characteristics were compared with those of the synthetic dielectric medium. Based on the D-optimal design coupled with cuckoo search algorithm, machining was carried out with various dielectric fluids and their influences on the metal removal rate, surface roughness, surface morphology and surface topography in EDM studied. The results proved that the canola oil methyl ester containing 0.5 wt% of nano-zirconia (C-0.5) had provided good surface finish, better surface topography, smooth surface morphology and high metal removal rate in comparison with the other dielectric fluids used in this study. [ABSTRACT FROM AUTHOR]

So far, many investigations have reported that Zr-based bulk metallic glasses (BMGs) could be precisely and flexibly shaped by electrical discharge machining (EDM). However, EDM induced crystallization and roughness is still a bottleneck. In this research, bench-mode electrochemical surface smoothing (ESS) in the NaCl-ethylene glycol (EG) electrolyte has been proposed to post-process the spark erosion treated Zr-based BMGs in order to solve the abovementioned problems. The utilization of the NaCl-EG electrolyte overcomes the difference in electrochemical dissolution mechanisms of multiple components contained in Zr-based BMGs. Taking a sort of Zr-based BMGs, Vit1 (Zr41.2Ti13.8Cu12.5Ni10.0Be22.5), as an example, voltammetry and chronoamperometry methods have been performed on the BMG surface before and after wire-EDM, respectively, in the NaCl-EG electrolyte to reveal the steady and transient electrochemical behaviors. In order to achieve high-efficiency and high-quality ESS of Zr-based BMGs, a 3D printed setup with lateral flushing has been developed, combined with the micron sized inter-electrode gap (IEG) and the pulse current. The surface morphologies after ESS have been compared to evaluate the effects of the initial surface morphologies, dwell time, and pulse parameters. The surface material properties and mechanical performance before and after ESS have also been investigated by EDS, XRD, XPS, and nanoindentation. The results suggests that the proposed ESS method is capable of quickly eliminating the crystalline layer induced by the thermal shock and reducing roughness caused by the discharge craters, which has been finally validated by fast ESS of two Zr-based BMG molds with ruled surfaces in the NaCl-EG solution. [ABSTRACT FROM AUTHOR]