Search

Plastic pollution at the nanoscale continues to pose adverse effects on environmental sustainability and human health. However, the detection of nanoplastics (NPLs) remains challenging due to limitations in methodology and instrumentation. Herein, a "green approach" for surface-enhanced Raman spectroscopy (SERS) was exploited to detect polystyrene nanospheres (PSNSs) in water, employing untreated filter paper and a simple syringe-filtration set-up. This SERS protocol not only enabled the filtration of nano-sized PSNSs, which are smaller than the pore size of the ordinary filter paper, but also offered SERS enhancement by utilizing quasi-spherical-shaped silver nanoparticles (AgNPs) as the SERS-active substrate. The filtering of NPLs was accomplished by adding an aggregating agent to the nanoparticle mixture, which caused the aggregation of NPLs and AgNPs, resulting in a larger cluster and more hot spots for SERS detection. The optimal aggregating agent and its concentration, as well as the volume ratio between the AgNPs and NPLs, were also optimized. This SERS method successfully detected and quantified PSNSs of various sizes (i.e., 100, 300, 460, 600, and 800 nm) down to a limit of detection (LOD) of about 0.31 μg mL−1. The method was also validated against the presence of several interferents (i.e., salts, sugars, amino acids, and surfactants) and was proven practical, as evidenced by the detection of 800nm PSNSs in drinking and tap water (LODs of 1.47 and 1.55 μg mL−1, respectively). [ABSTRACT FROM AUTHOR]

The accumulation of plastic packaging wastes in the natural environment highlights the significance of sustainable alternatives. Paper is widely used as a biodegradable packaging material, but poor mechanical strength, barrier properties, and water resistance limit its utility. Typical paper coating materials applied to overcome such drawbacks, such as polyethylene (PE) and ethylene vinyl alcohol (EVOH), are not desirable for sustainability due to environmental persistence. Here, we report a biodegradable, biocompatible, robust, and high-barrier paper coating strategy using boric acid-crosslinked poly(vinyl alcohol) (PVA). Various crosslinked-PVA solutions were prepared using boric acid (BA) and hydrochloric acid (HCl) as a crosslinker and an acid catalyst, respectively. The solutions were coated onto the Kraft paper (KP) through facile bar coating with epichlorohydrin (ECH) as a binder (henceforth referred to as coated papers). The coated papers (KP-P, KP-PB, KP-PBH) show remarkably improved oxygen (∼0.89 cc m−2 d−1) and water vapor (∼5.17 g m−2 d−1) barrier properties as well as tensile strength (∼53.0 MPa) that is retained in moist conditions. The coated papers were significantly mineralized into CO2 (59.2–81.6% over 111 d) in the simulated marine environment biodegradation test. Depolymerization of polymer chains and surface degradation of coated papers are evidenced via FT-IR and SEM, respectively. The microcosm test revealed that the intensive disintegration of the coated papers is synergistically driven by both biotic and abiotic factors (i.e., mechanical stress). Moreover, the in vitro biocompatibility tests employing human embryonic kidney and mouse embryonic fibroblast cells, and in vivo biocompatibility test with mice suggest that the coated papers are highly biocompatible. This work provides a promising strategy for paper packaging that enhances packaging performance without compromising environmental sustainability. [ABSTRACT FROM AUTHOR]

This report presents an investigation into the use of carbon paper electrodes prepared from chitosan-adhered graphene magnetite nanoparticles for the analysis of Cr(VI). The preparation and storage of carbon paper electrodes is a simple process, and these electrodes are easier to replace than electrodes modified by more conventional methods. The electrochemical detection of Cr(VI) using square wave adsorption cathodic dissolution voltammetry (SWAdCSV) with high selectivity and sensitivity, as well as the optimum conditions for the preparation of the electrodes and the electrode parameters affecting the SWAdCSV signal, were the main points of focus of the investigation. Cr(VI) was detected linearly in the range of 4-40 μg L-1 with a detection limit of 2.84 μg L-1. The electrode output precision, calculated as %RSD, was 7.16% (n = 6), and this was the measurement used for the detection of Cr(VI) in standard and test samples with recoveries between 89% and 114%. The results were consistent with those obtained using the standard UV-Vis spectrophotometric method with a paired t-test at 95% confidence level. [ABSTRACT FROM AUTHOR]

Non-enzymatic electrochemical blood glucose sensors often suffer from issues such as requiring an alkaline environment, limited monitoring range, and poor anti-interference properties. Carbon substrates have been demonstrated to improve the performance of non-enzymatic sensors, but complex and energy-consuming manufacturing processes restrict their use. Herein, a simple and green approach for the preparation of 3D porous Au/Au-Pt networks (PAAPNs) is proposed using tissue paper for recycling as the nanomaterial substrate to deposit Au-Pt bimetallic nanoparticles. The unique structure of the PAAPNs sensor allows for low-potential operation (-1.0 V) with a wide monitoring range (-0.25 to 36 mM) in a neutral environment. Moreover, the sensor exhibited excellent selectivity (<10% response of interference) even without the use of an anti-interference outer membrane. Further investigation using density functional theory (DFT) simulation revealed the synergistic effect between Au and Pt in promoting glucose oxidation. Overall, this work provides a simple and low-carbon footprint method for creating carbon substrates from tissue paper for recycling, offering new opportunities for fabricating novel value-added nanomaterials for medical sensing applications. [ABSTRACT FROM AUTHOR]

The first step in blood testing necessitates blood separation to obtain an adequate volume of plasma. Traditional centrifugation is bulky, expensive and electricity-powered, which is not suitable for micro-scale blood plasma separation in point-of-care testing (POCT) cases. Microfluidic paper-based plasma separation devices present a promising alternative for plasma separation in such occasions. However, they are limited in terms of plasma yield, which hinders analyte detection. Herein, we proposed a humidity-enhanced paper-based microfluidic plasma separation method to address this issue. Specifically, paper was first treated by blood-typing antibodies, then samples of whole blood were introduced into the prepared paper. After waiting for 5 min for RBC agglutination and plasma wicking under high humidity, micro-scale plasma separation from whole blood was achieved. As a result, an extremely high plasma yield of up to 60.1% could be separated from whole blood through using Xuan-paper. Meanwhile, the purity of plasma could reach 99.99%. Finally, this innovative approach was effortlessly integrated into distance-based glucose concentration detection, enabling rapid determination of blood glucose levels through naked-eye observation. Considering the simplicity and inexpensiveness of this method, we believe that this technology could be integrated to more paper-based microfluidic analytical devices for rapid and accurate detection of plasma analytes in POCT. [ABSTRACT FROM AUTHOR]

Paper-based microfluidics combined with potentiometric measurement has emerged as an attractive approach for detecting various chemical ionic moieties. Detection of heavy metal ions, using paper substrates as solution sampling and delivery systems remains challenging despite efforts to introduce several physico-chemical paper substrate modifications to stop adsorption of ions onto the paper substrates. This study quantitatively investigates the adsorption of heavy metal ions on the paper substrates during paper-based potentiometric measurements and explains the super-Nernstian response of potentiometric sensors through local depletion of heavy metal ions from the solution. Consequently, based on the investigated ion adsorption, a corrective potential protocol was established for the electrodes coupled with paper-based solution sampling by predicting interference free sensor response from paper-based measurement. Furthermore, the ion adsorption was also recorded for mixed metal ion solutions to understand competitive primary/interfering ions adsorption onto the paper substrates and establish corrective measures to predict interference free sensor response. In this method, no modifications of the paper substrates are necessary before actual potentiometric measurements. The proposed corrective protocol allows prediction of sensor response based on the paper-based solution sampling potentiometric measurement, providing a simple methodological approach based on correction of potential readout of the potentiometric sensor, thus completely resigning from the need of modifying paper substrate for measurements of heavy metal ions. [ABSTRACT FROM AUTHOR]

Serum contains rich elemental information, and the elemental analysis of the serum using laser-induced breakdown spectroscopy (LIBS) can help with the diagnosis and treatment of cancer. In this work, serum specimens from breast cancer patients were used as samples, and the elements Mg, Ca, and K were analyzed using LIBS. Silver nanoparticles (Ag NPs) were introduced to enhance spectral emission intensities, and this technique is known as nanoparticle-enhanced LIBS (NELIBS). An Ag NP-coated filter paper (Ag NP paper) substrate was prepared and was compared with silicon and aluminum substrates for NELIBS analysis. The Ag NP paper substrate showed lower spectral intensity variances and better elemental distribution uniformity due to the reduced coffee-ring effect compared with silicon and aluminum substrates. The enhanced effect of the Ag NP paper was optimized by adjusting serum volume and Ag NPs concentration. It was found that Mg, Ca, and K required different optimal conditions for spectral enhancement. The highest enhancement factors (EF) for Mg, Ca, and K were 1.85, 1.76, and 3.10, respectively. The electron temperature (Te) and electron number density (Ne) of NELIBS plasmas were measured using the Boltzmann plot and Stark broadening methods and compared with those of the normal LIBS plasmas. The Te and Ne of the NELIBS and normal LIBS samples were generally comparable with each other. Higher Ag NP concentrations led to lower Te values for NELIBS plasmas. [ABSTRACT FROM AUTHOR]

The demand for flexible pressure sensors with high performance is increasing with the growing wearable technology market. According to the developing requirement for green electronics, paper-based sensors, which are more environmentally friendly, have received more and more attention. However, the intrinsic mechanical properties of paper materials limit the sensing performance of paper-based sensors, such as restricted working range and response bandwidth. Herein, a rigid–soft hybrid design strategy is proposed to improve the sensing performance of paper-based pressure sensors, and bioinspired microstructures are introduced into the architecture of sensors for further improvement. As a result, the prepared paper-based pressure sensor has a faster response/recovery speed (<50 ms), a wide sensing range (1 MPa) and frequency response bandwidth (0.05–1000 Hz) and excellent cycling stability (5000 cycles). In addition, the paper-based pressure sensor is superhydrophobic with a water contact angle of 152.62°. Based on the excellent sensing performance and waterproofness, the paper-based pressure sensor can be used as a wearable device for detecting joint movements or gait of humans/robots in both air and underwater. In addition, it can be used to send communication signals, showing great potential for applications in future underwater rescue. [ABSTRACT FROM AUTHOR]

A simple and mild stimulus-responsive fluorescent supramolecular polymer network was constructed from a pillararene-based multi-functional monomer through multiple noncovalent interactions and used as a rewritable paper. [ABSTRACT FROM AUTHOR]

Multiple protocols have been reported to fabricate paper-based analytical devices (PADs). However, some of these techniques must be revised because of the instrumentation required. This paper describes a versatile and globally affordable method to fabricate PADs using office paper as a substrate and a laser printing technique to define hydrophobic barriers on paper surfaces. To demonstrate the feasibility of the alternatives proposed in this study, the fabrication of devices for three types of detection commonly associated with using PADs was demonstrated: colorimetric detection, electrochemical detection, and mass spectrometry associated with a paper-spray ionization (PSI-MS) technique. Besides that, an evaluation of the type of paper used and chemical modifications required on the substrate surface are also presented in this report. Overall, the developed protocol was suitable for using office paper as a substrate, and the laser printing technique as an efficient fabrication method when using this substrate is accessible at a resource-limited point-of-need. Target analytes were used as a proof of concept for these detection techniques. Colorimetric detection was carried out for acetaminophen, iron, nitrate, and nitrite with limits of detection of 0.04 μg, 4.5 mg mL−1, 2.7 μmol L−1, and 6.8 μmol L−1, respectively. A limit of detection of 0.048 fg mL−1 was obtained for the electrochemical analysis of prostate-specific antigen. Colorimetric and electrochemical devices revealed satisfactory performance when office paper with a grammage of 90 g m−2 was employed. Methyldopa analysis was also carried out using PSI-MS, which showed a good response in the same paper weight and behavior compared to chromatographic paper. [ABSTRACT FROM AUTHOR]

A new CdII-based luminescent metal–organic framework (LMOF) with the formula {[Cd(BIBT)(NDC)]·solvents}n (JXUST-32, BIBT = 4,7-bi(1H-imidazol-1-yl)benzo-[2,1,3]thiadiazole and H2NDC = 2,6-naphthalenedicarboxylic acid) was successfully synthesized by a solvothermal method. JXUST-32 shows a two-dimensional (4,4)-connected network and exhibits significant fluorescence red shift and slight enhancement for H2PO4− and CO32− sensing with detection limits of 0.11 and 0.12 μM, respectively. In addition, JXUST-32 has good thermal stability, chemical stability and recyclability. Significantly, JXUST-32 represents a fluorescence red-shift dual response MOF sensor for H2PO4− and CO32− detection and the analytes can be identified by the naked eye, aerosol jet printing filter paper, light-emitting diode beads and luminescent films. [ABSTRACT FROM AUTHOR]

As a kind of organic basic compound containing nitrogen, biogenic amine is released from food spoilage and considered as an indicator for monitoring food freshness. Herein, an excellent dual-emission ratiometric fluorescent sensor for eight kinds of biogenic amines was established via the facile mixing of pH-responsive carbon dots and Rhodamine B. The developed sensor shows a rapid response (10 s), low limit of detection (0.733–3.943 μM) and a wide linear range (0–150 μM). More importantly, a portable fluorescent filter paper was prepared by simple dispersing the filter paper in a solution mixture of carbon dots and Rhodamine B. The obtained fluorescent filter paper based sensor showed an obvious color change in the presence of biogenic amine vapor derived from shrimp and mushroom. The results revealed that this sensor could realize the on-site and visual detection of biogenic amines in real food samples, making it suitable for potential application in food safety monitoring. [ABSTRACT FROM AUTHOR]

Paper-based ratiometric fluorescence sensors are normally prepared using two or more types of fluorescent materials on a paper chip for simple, low-cost and fast detection. However, the choice of multi-step and one-step modifications on the paper chip affects the analytical performance. Herein, a novel paper-based dual-emission ratiometric fluorescence sensor was designed for the selective detection of tetracycline (TC). Carbon dots (CDs) modified with Eu3+ were combined with a sealed paper-based microfluidic chip by two methods: one-step grafting of CDs-Eu3+ on paper and step-by-step grafting of CDs and Eu3+ on paper. The analytical performance was studied and optimized respectively. The red fluorescence of Eu3+ at 450 nm is enhanced and the blue fluorescence of CDs at 617 nm is quenched by energy transfer in the presence of TC. Under optimal conditions, TC is selectively determined in the linear range from 0.1 μM to 100 μM with a detection limit of 0.03 μM by the step-by-step grafting method. In addition, the sealed paper chip could effectively prevent pollution and volatilization from the reagent. This technique has been used to analyze TC in seafood aquaculture water with satisfactory results. [ABSTRACT FROM AUTHOR]

A simple, rapid chemical coating and patterning method was developed and optimized for paper-based substrates for use in paper spray mass spectrometry (PS-MS). A variety of chlorosilanes were explored for coating paper substrates, and their effectiveness in forming hydrophobic surfaces was characterized via contact angle goniometry, scanning electron microscopy, and energy dispersive X-ray spectroscopy. Trichloromethylsilane was selected as the primary coating agent because of the short time required to produce a hydrophobic surface (contact angle > 130°), as well as the ease of patterning. Patterning was performed using 3D-printed masks and an oxygen/plasma cleaner. Optimal mask thickness and oxygen/plasma cleaning parameters were determined to produce channels varying from 0.5 to 2.5 mm in width. The effectiveness of the patterned substrates for PS-MS was determined via analysis of four antiretrovirals: emtricitabine, lamivudine, efavirenz, and dolutegravir. Calibration curves were made for each antiretroviral at varying channel widths, and the limits of detection and limits of quantification for each drug were determined. These results show that this patterning method results in an average 7.2-fold improvement in sensitivity and an average 190-fold improvement in limits of detection over uncoated paper substrates in a neat matrix. In a proof-of-concept experiment, calibration curves were generated for each antiretroviral in urine. A patterned paper substrate with a 2-mm channel resulted in an average 7.4-fold improvement in sensitivity and an average 18-fold improvement in limits of detection over uncoated paper substrates. [ABSTRACT FROM AUTHOR]

Developing new forms of flexible zinc–air (Zn–air) batteries is crucial to economic growth. Nevertheless, the absence of an oxygen evolution reaction catalyst with high catalytic efficiency and low-cost causes instability of Zn–air battery cycling and economic unviability, respectively. In this paper, a leaf-like N-doped carbon structure with CoS2 nanoparticles self-supported on carbon fiber paper (CoS2-CZ@CFP) was developed as an air electrode for Zn–air batteries, which not only uses nonprecious metal elements, but also has a self-supporting configuration, enhancing the contact between the catalyst and electrode while facilitating the transfer of electrons. Sulfur as the source gas was introduced into Co-doped metal–organic skeletons (Co-ZIFs) anchored on carbon fiber paper (CFP) for in situ vulcanizing transition metal Co, which successfully ensures the uniform distribution of sulfide particles in the carbon matrix, hence enriching active catalyst sites. The CoS2-CZ@CFP demonstrated an overpotential of 1.611 V at J = 50 mA cm−2, superior to RuO2@CFP (1.814 V). A Zn–air battery fabricated using the synthesized CoS2-CZ@CFP exhibited an extended life cycle of 117 h. This research paves the way for a novel method of designing self-supporting configurations of sulfides and carbon matrix composites as promising air electrodes applicable to Zn–air batteries. [ABSTRACT FROM AUTHOR]

Selective enrichment of La(III) by green material as an industrial raw material is of great research interest. In this study, the selective interaction between P and La(III) was utilized, and waste paper (WP) modified with phytic acid (PA) was used to adsorb La(III) from water using a simple one-pot method. The adsorption capacity was 237.23 mg g−1 (30 °C, pH = 5, initial concentration of 200 mg L−1). The equilibrium isotherm fitted the Langmuir isotherm model well. The adsorption equilibrium was reached after 15 min. The adsorption kinetics followed the pseudo-second-order kinetic model, indicating that the adsorption mechanism of the material towards La(III) is single-layer chemisorption. It selectively adsorbed La(III) from four coexisting substances (Pb, Ni, Cu, and Co). After six cycles, the adsorption efficiency of the adsorbent material remained at 60%. [ABSTRACT FROM AUTHOR]

A novel microfluidic paper-based analytical device with dual colorimetric and electrochemical detection (dual μPAD) was developed for the assessment of transferrin saturation (TSAT) in samples from ischemic stroke patients. TSAT was calculated from the ratio between transferrin-bound iron, which was colorimetrically measured, and the total iron-binding capacity, which was electrochemically measured. To this end, a μPAD was smartly designed, which integrated both colorimetric and electrochemical detection reservoirs, communicating via a microchannel acting as a chemical reactor, and with preloading/storing capabilities (reagent-free device). This approach allowed the dual and simultaneous determination of both parameters, providing an improvement in the reliability of the results due to an independent signal principle and processing. The μPADs were validated by analyzing a certified reference material, showing excellent accuracy (Er ≤ 5%) and precision (RSD ≤ 2%). Then they were applied to the analysis of diagnosed serum samples from ischemic stroke patients. The results were compared to those provided by a free-interference method (urea-PAGE). Impressively, both methods exhibited a good correlation (r = 0.96, p < 0.05) and no significant differences were found between them (slope 1.0 ± 0.1 and the intercept 1 ± 4, p < 0.05), demonstrating the excellent accuracy of our approach during the analysis of complex samples from ischemic stroke patients, using just 90 μL of clinical samples and taking less than 90 min in comparison with the 18 hours required by the urea-PAGE approach. The developed fully integrated colorimetric-electrochemical μPAD is a promising ready to use reagent-free device for the point-of-care testing of TSAT, which can be used to assist physicians in the fast diagnosis and prognosis of ischemic strokes, where the decision-time is crucial for the patient's survival. [ABSTRACT FROM AUTHOR]

Paper-based rapid diagnostic tests (RDTs) are an essential component of modern healthcare, particularly for the management of infectious diseases. Despite their utility, these capillary-driven RDTs are compromised by high failure rates, primarily caused by user error. This limits their utility in complex assays that require multiple user operations. Here, we demonstrate how this issue can be directly addressed through continuous electrochemical monitoring of reagent flow inside an RDT using embedded graphenized electrodes. Our method relies on applying short voltage pulses and measuring variations in capacitive discharge currents to precisely determine the flow times of injected samples and reagents. This information is reported to the user, guiding them through the testing process, highlighting failure cases and ultimately decreasing errors. Significantly, the same electrodes can be used to quantify electrochemical signals from immunoassays, providing an integrated solution for both monitoring assays and reporting results. We demonstrate the applicability of this approach in a serology test for the detection of anti-SARS-CoV-2 IgG in clinical serum samples. This method paves the way towards "smart" RDTs able to continuously monitor the testing process and improve the robustness of point-of-care diagnostics. [ABSTRACT FROM AUTHOR]

Nowadays, kidney dysfunction is a common health issue due to the modernized lifestyle. Even though medications are commercially available to treat kidney diseases, early diagnosis is crucial and challenging. Clinically, measuring urine creatinine and pH has gained significant interest as a way to diagnose kidney diseases early. In the present work, we attempted to develop a low-cost, robust, accurate and naked-eye colorimetric method to determine both creatinine levels and pH variations in artificial urine samples using a simple 3D-printed hybrid microfluidic device. Creatinine was detected by the incorporation of the traditional Jaffe test onto the hybrid paper–PMMA microfluidic device and pH (4–8) was measured by a simple anthocyanin test. Notably, the tests were established without employing any sophisticated or costly instrument clusters. The developed 3D-printed microfluidic probe showed a limit of detection (LOD) of 0.04 mM for creatinine over a concentration range of 1–10 mM, with a regression coefficient (R2) of 0.995 in laboratory conditions. Interestingly, the experimental data obtained with artificial urine exhibited a wide linear range from 0.1 mM to 5 mM under different pH values ranging from 4 to 8 in the presence of matrices commonly found in urine samples other than proteins, indicating the potential use of this method in pre-clinical analysis. Since the wide linear range of urine creatinine in artificial urine samples falls well below the clinically relevant concentrations in humans (0.07–0.27 mM), the developed lab-on-chip device is further suitable for clinical evaluation with proper ethical clearance. This 3D-printed hybrid microfluidic colorimetry-based creatinine detection and pH indicator platform can be beneficial in the healthcare sector due to the on-site testing capability, cost-effectiveness, ease of use, robustness, and instrument-free approach. [ABSTRACT FROM AUTHOR]

In this work, we report on five novel coordination polymers (CPs) based on the linkage of the [Cd(6apic)2] building block [where 6apic = 6-aminopicolinate] by different bipyridine-type organic spacers, forming different coordination compounds with the following formulae: [Cd(μ-6apic)2]n (1), {[Cd(6apic)2(μ-bipy)]·H2O}n (2), {[Cd(6apic)2(μ-bpe)]·2H2O}n (3), [Cd(6apic)(μ-6apic)(μ-bpa)0.5]n (4) and {[Cd2(6apic)4(μ-tmbp)]·7H2O}n (5) [where bipy = 4,4′-bipyridine, bpe = 1,2-di(4-pyridyl)ethylene, bpa = 1,2-di(4-pyridyl)ethane (bpa) and tmbp = 1,3-di(4-pyridyl)propane]. Most of the synthesized compounds form infinite metal–organic rods through the linkage of the building block by the bipyridine-type linker, except in the case of compound 4 whose assembly forms a densely packed 3D architecture. All compounds were fully characterized and their photoluminescence properties were studied experimentally and computationally through density functional theory (DFT) calculations. All compounds display, upon UV excitation, a similar blue emission of variable intensity depending on the linker employed for the connection of the building units, among which compound 2 deserves to be highlighted for its room temperature phosphorescence (RTP) with an emission lifetime of 32 ms that extends to 79 ms at low temperature. These good photoluminescence properties, in addition to its stability in water over a wide pH range (between 2 and 10), motivated us to study compound 2 as a sensor for the detection of metal ions in water, and it showed high sensitivity to Fe3+ through a fluorescence turn-off mechanism and an unspecific turn-on response to Zn2+. Furthermore, the compound is processed as a paper-based analytical device (PAD) in which the phosphorescence emission is preserved, improving the sensing capacity toward Fe3+ ions. [ABSTRACT FROM AUTHOR]

This study introduces the development of a photothermal-based microfluidic paper analytical device (PT-µPAD) integrated with near-field communication (NFC) technology and smartphone readout for enzyme-free glucose quantification in human samples. With the properties of gold nanoparticles (AuNPs) both as a nanozyme and as a photothermal substrate, there is no need for costly reagents like enzymes or a readout instrumentation for the selective and sensitive detection of glucose. In PT-µPADs, AuNPs are etched by hydrogen peroxide (H2O2) generated from glucose catalysis. Photothermal detection from the plasmonic heating of these AuNPs when illuminated by a 533nm LED light source is achieved by inserting the PT-µPAD sensor into a portable NFC platform suitable for smartphone readout. Temperature variation is directly proportional to the glucose concentration. After optimization, we acquired a linear range between 5.0 and 20.0 µmol L−1 (R2 = 0.9967) and a limit of detection (LOD) of 25.0 nmol L−1 for glucose. Additionally, while our sensor does not utilize any enzyme, it is remarkably selective to glucose with no effects from interferences. Recovery studies in various human control samples indicated a range of 99.73–102.66% with the highest RSD of 3.53%, making it highly accurate and precise. Moreover, our method is more sensitive than other methods relying on conventional µPADs for glucose sensing. By integrating the potential benefits of microfluidics, nanomaterials as nanozymes, and NFC technology for wireless readout, our sensor demonstrates great promise as an accessible, affordable, and shelf-stable device for glucose quantification. Moreover, this concept can be extended to detect other molecules of interest as a point-of-care (POC) diagnostics device. [ABSTRACT FROM AUTHOR]

We reported a colorimetric paper-based device by integrating the modified acid RNA-cleaving DNAzymes (MaRCD-EC1) for highly sensitive (detection limit = 102 CFU mL−1), and rapid (within 30 min) detection of E. coli without amplification. This device exhibited a clinical sensitivity of 100% and a specificity of 100% in identifying E. coli-associated urinary tract infections (UTIs) using the clinical urine samples. [ABSTRACT FROM AUTHOR]

Gossypol, a phytotoxicant in cotton-seed oil, has been found to sensitize Tb(III)-luminescence in a supramolecular hydrogel. Based on this observation, a paper-based sensor has been developed to detect gossypol with a limit of detection (LOD) of 2.9 nM. This is the first report of water-based detection with the highest sensitivity involving turn-on time-gated luminescence. This method was also able to sense gossypol in commercial crude cotton-seed oil. [ABSTRACT FROM AUTHOR]

We report a series of structurally relevant copper phenanthroline complexes as pre-catalysts for highly selective electrocatalytic reduction of CO2 to C2 products using inexpensive carbon paper electrodes. The Cu complexes with non-substituted phenanthroline promote the production of ethylene with a high faradaic efficiency of 71.2%, while the one with pyridinium-functionalized ligands is more selective for ethanol. The C2 selectivity can be effectively tuned by increasing the number of coordinated phenanthrolines and remains high at a wide range of potentials. [ABSTRACT FROM AUTHOR]

Petroleum-based plastics are useful, but they pose a huge threat to the environment and human health. The development of sustainable cellulose paper materials with excellent mechanical and water-resistance properties to replace plastics is highly desirable but also challenging. Herein, we report a new kind of rosin-based modifier synthesized from fully hydrogenated rosin and (3-glycidoxypropyl)triethoxysilane, which can covalently bind with cellulose fiber networks to improve the hydrophobicity and weaken the capillarity of cellulose paper. The rosin-grafted cellulose composite paper shows a unique combination of water resistance (water absorption of 19.2% and 37.9% in 25 and 90 °C water, respectively) and high strength (tensile strength of 47.9 MPa and Young's modulus of 2.32 GPa). Moreover, the rosin-grafted cellulose composite paper can be completely degraded when buried in soil for up to 100 days, and it can be recycled when treated with an alkali. These impressive performances make rosin-grafted cellulose composite paper a promising eco-friendly alternative material to replace plastics in straws, boxes, cups, bags and so on. [ABSTRACT FROM AUTHOR]

Naphthalenediimide derivative-absorbed papers, which were prepared by dropping chloroform solution, showed fluorescence under photoirradiation after exposure to vapors of small aromatic guests. The fluorescence intensity and maximum wavelength depended on the type of guest aromatic molecules, similar to the crystal. The naphthalenediimide derivative-absorbed papers showed vapochromic and mechanochromic properties. [ABSTRACT FROM AUTHOR]

Microfluidic paper-based analytical devices (microPADs) are emerging as simple-to-use, low-cost point-of-care testing platforms. Such devices are mostly fabricated at present by creating hydrophobic barriers using wax or photoresist patterning on porous paper sheets. Even though devices fabricated using these methods are used and tested with a wide variety of analytes, still they pose many serious practical limitations for low-cost automated mass fabrication for their widespread applicability. We present an affordable and simple two-step process – cut and heat (CH-microPADs) – for the selective fabrication of hydrophilic channels and reservoirs on a wide variety of porous media such as tissue/printing/filter paper and cloth types, such as cotton and polyester, by a lamination process. The technique presents many advantages as compared to existing commonly used methods. The devices possess excellent mechanical strength against bending, folding and twisting, making them virtually unbreakable. They are structurally flexible and show good chemical resistance to various solvents, acids and bases, presenting widespread applicability in areas such as clinical diagnostics, biological sensing applications, food processing, and the chemical industry. Fabricated paper media 96 well-plate CH-microPAD configurations were tested for cell culture applications using mice embryonic fibroblasts and detection of proteins and enzymes using ELISA. With a simple two-step process and minimal human intervention, the technique presents a promising step towards mass fabrication of inexpensive disposable diagnostic devices for both resource-limited and developed regions. [ABSTRACT FROM AUTHOR]

This communication describes the development of polyvinyl chloride electrochemical system in which a paper layer loaded with reagents is inserted into the device, demonstrating a new concept of a paper card-like pad for a reagent-free and easy measurement of the target analyte in solution. This device detects glucose in artificial tears in the range of 0.2–2 mM with a detection limit of 50 μM by simply adding the artificial tears to the paper card-like pad. The novel configuration goes beyond the state of the art, widening the application range of paper in the design of smart analytical devices. [ABSTRACT FROM AUTHOR]

In the practical application of microwave absorbing materials, traditional powder materials need to be mixed with the matrix to fabricate composite coatings. However, the complex preparation process of composite coatings and the uneven dispersion of powders in the matrix limit their application. To solve these problems, two-dimensional (2D) F-WS2/CP composite films were prepared by using carbon paper (CP) as a dispersion matrix and loading flower-like WS2 on its surface through a simple hydrothermal method. The morphology and microwave absorption (MA) performance of the composite films are easily regulated by adjusting the amount of reaction precursors. The combination of WS2 and CP facilitates impedance matching and improves the electromagnetic wave attenuation performance based on the synergistic effect of different loss mechanisms including multiple reflections and scattering, interfacial polarization, dipolar polarization, and conduction loss. At a low filler content (5 wt%), the maximum reflection loss (RL) of the composite film is up to -50 dB (99.999% energy absorption) at 12.5 GHz with 2.8 mm thickness. Moreover, at a relatively thin 1.8 mm thickness, its maximum RL remains -35 dB (>99.9% energy absorption). The as-prepared composite film shows excellent MA properties at a thinner thickness and lower filling content, providing inspiration for the preparation of light weight and efficient 2D thin-film microwave absorbers in the future. [ABSTRACT FROM AUTHOR]

Safe, accurate, and reliable analysis of urinary biomarkers is clinically important for early detection and monitoring of the progression of chronic kidney disease (CKD), as it has become one of the world's most prevalent non-communicable diseases. However, current technologies for measuring urinary biomarkers are either time-consuming and limited to well-equipped hospitals or lack the necessary sensitivity for quantitative analysis and post a health risk to frontline practitioners. Here we report a robust paper-based dual functional biosensor, which is integrated with the clinical urine sampling vial, for the simultaneous and quantitative analysis of pH and glucose in urine. The pH sensor was fabricated by electrochemically depositing IrOx onto a paper substrate using optimised parameters, which enabled an ultrahigh sensitivity of 71.58 mV pH-1. Glucose oxidase (GOx) was used in combination with an electrochemically deposited Prussian blue layer for the detection of glucose, and its performance was enhanced by gold nanoparticles (AuNPs), chitosan, and graphite composites, achieving a sensitivity of 1.5 μA mM-1. This dual function biosensor was validated using clinical urine samples, where a correlation coefficient of 0.96 for pH and 0.98 for glucose detection was achieved with commercial methods as references. More importantly, the urine sampling vial was kept sealed throughout the sample-to-result process, which minimised the health risk to frontline practitioners and simplified the diagnostic procedures. This diagnostic platform, therefore, holds high promise as a rapid, accurate, safe, and user-friendly point-of-care (POC) technology for the analysis of urinary biomarkers in frontline clinical settings. [ABSTRACT FROM AUTHOR]

This article introduces distance-based paper analytical devices (dPADs) integrated with molecularly imprinted polymers (MIPs) and carbon dots (CDs) for simultaneous quantification of cytokine biomarkers, namely C-reactive protein (CRP), tumor necrosis factor-alpha (TNF-a), and interleukin-6 (IL-6) in human biological samples for diagnosis of cytokine syndrome. Using fluorescent CDs and MIP technology, the dPAD exhibits high selectivity and sensitivity. Detection is based on fluorescence quenching of CDs achieved through the interaction of the target analytes with the MIP layer on the paper substrate. Quantitative analysis is easily accomplished by measuring the distance length of quenched fluorescence with a traditional ruler and naked eye readout enabling rapid diagnosis of cytokine syndrome and the underlying infection. Our sensor demonstrated linear ranges of 2.50-24.0 pg mL-1 (R2 = 0.9974), 0.25-3.20 pg mL-1 (R2 = 0.9985), and 1.50-16.0 pg mL-1 (R2 = 0.9966) with detection limits (LODs) of 2.50, 0.25, and 1.50 pg mL-1 for CRP, TNF-a, and IL-6, respectively. This sensor also demonstrated remarkable selectivity compared to a sensor employing a non-imprinted polymer (NIP), and precision with the highest relative standard deviation (RSD) of 5.14%. The sensor is more accessible compared to prior methods relying on expensive reagents and instruments and complex fabrication methods. Furthermore, the assay provided notable accuracy for monitoring these biomarkers in various human samples with recovery percentages ranging between 99.22% and 103.58%. By integrating microfluidic systems, nanosensing, and MIPs technology, our developed dPADs hold significant potential as a cost-effective and user-friendly analytical method for point-of-care diagnostics (POC) of cytokine-related disorders. This concept can be further extended to developing diagnostic devices for other biomarkers. [ABSTRACT FROM AUTHOR]

Paper-based electrochemical sensors have the characteristics of flexibility, biocompatibility, environmental protection, low cost, wide availability, and hydropathy, which make them very suitable for the development and application of biological detection. This work proposes electrospun cellulose acetate nanofiber (CA NF)-decorated paper-based screen-printed (PBSP) electrode electrochemical sensors. The CA NFs were directly collected on the PBSP electrode through an electrospinning technique at an optimized voltage of 16 kV for 10 min. The sensor was functionalized with different bio-sensitive materials for detecting different targets, and its sensing capability was evaluated by CV, DPV, and chronoamperometry methods. The test results demonstrated that the CA NFs enhanced the detection sensitivity of the PBSP electrode, and the sensor showed good stability, repeatability, and specificity (p < 0.01, N = 3). The electrochemical sensing of the CA NF-decorated PBSP electrode exhibited a short detection duration of ∼5–7 min and detection ranges of 1 nmol mL−1–100 μmol mL−1, 100 fg mL−1–10 μg mL−1, and 1.5 × 102–106 CFU mL−1 and limits of detection of 0.71 nmol mL−1, 89.1 fg mL−1, and 30 CFU mL−1 for glucose, Ag85B protein, and E. coli O157:H7, respectively. These CA NF-decorated PBSP sensors can be used as a general electrochemical tool to detect, for example, organic substances, proteins, and bacteria, which are expected to achieve point-of-care testing of pathogenic microorganisms and have wide application prospects in biomedicine, clinical diagnosis, environmental monitoring, and food safety. [ABSTRACT FROM AUTHOR]

A robust superhydrophobic filter paper was developed through a coating technique, simple and facile, cost-effective, eco-friendly, and defensible, for wide portfolio applications. To develop super hydrophobic filter papers, the paper was coated with inorganic–organic hybrid nanocomposites comprising zinc oxide, chitin, and polycaprolactone (chitin–ZnO–PCL) and zinc oxide, chitosan, and polycaprolactone (chitosan–ZnO–PCL) hybrids through the grafting method. The preparation of a superhydrophobic surface by dip-coating deposition is a facile process. Zinc oxide nanoparticles grafted with chitin–PCL and chitosan–PCL hybrids coated on paper exhibit superhydrophobic properties. Water contact angle measurement carried out using a goniometer showed the average static water angle values of 145° and 160° for the chitin–ZnO–PCL and chitosan–ZnO–PCL grafted hybrid coated surfaces, respectively. The surface morphology of the coating was studied using scanning electron microscopy, X-ray powder diffraction, UV radiation, and Fourier transform infrared spectroscopy. In addition, durability, oil/water separation, bio-degradability, and self-cleaning ability through water flush-out were also studied and reported. The results show that the coated filter papers possess excellent superhydrophobic properties for real-time applications. [ABSTRACT FROM AUTHOR]

Nucleic acid extraction (NAE) plays a crucial role for diagnostic testing procedures. For decades, dried blood spots (DBS) have been used for serology, drug monitoring, and molecular studies. However, extracting nucleic acids from DBS remains a significant challenge, especially when attempting to implement these applications to the point-of-care (POC). To address this issue, we have developed a paper-based NAE method using cellulose filter papers (DBSFP) that operates without the need for electricity (at room temperature). Our method allows for NAE in less than 7 min, and it involves grade 3 filter paper pre-treated with 8% (v/v) igepal surfactant, 1 min washing step with 1× PBS, and 5 min incubation at room temperature in 1× TE buffer. The performance of the methodology was assessed with loop-mediated isothermal amplification (LAMP), targeting the human reference gene beta-actin and the kelch 13 gene from P. falciparum. The developed method was evaluated against FTA cards and magnetic bead-based purification, using time-to-positive (min) for comparative analysis. Furthermore, we optimised our approach to take advantage of the dual functionality of the paper-based extraction, allowing for elution (eluted disk) as well as direct placement of the disk in the LAMP reaction (in situ disk). This flexibility extends to eukaryotic cells, bacterial cells, and viral particles. We successfully validated the method for RNA/DNA detection and demonstrated its compatibility with whole blood stored in anticoagulants. Additionally, we studied the compatibility of DBSFP with colorimetric and lateral flow detection, showcasing its potential for POC applications. Across various tested matrices, targets, and experimental conditions, our results were comparable to those obtained using gold standard methods, highlighting the versatility of our methodology. In summary, this manuscript presents a cost-effective solution for NAE from DBS, enabling molecular testing in virtually any POC setting. When combined with LAMP, our approach provides sample-to-result detection in under 35 minutes. [ABSTRACT FROM AUTHOR]

A simple, portable and cost-effective paper-based analysis device is developed for quantitative determination of ascorbic acid (AA) based on the UV-induced oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB). The method does not involve the introduction of any enzyme or external oxidants. More importantly, large equipment is not needed and only a 20 μL sample is needed for each analysis which only takes 8 min. The filter paper is pre-treated with TMB and it turns blue upon UV irradiation because TMB is a self-photosensitizer. The phenol hydroxyl groups of AA can inhibit photo-triggered oxidation resulting in a lighter blue color. The color signal is captured using a smartphone and analyzed using color analysis software. A series of factors that affect the performance of the device are investigated, including the concentration of TMB, buffer pH, channel selection, and irradiation time. The analytical performance is evaluated, and the results show that the method has a wide detection range of 0.05–1.0 mmol L−1 as well as a high selectivity and reproducibility. The proposed method is applied for assaying AA in beverage samples and a VC tablet, and the results correspond to those obtained using the UV method. The results of the recovery test of human serum indicate that the proposed method is feasible in biological samples. This device is easy to fabricate, and convenient to store and transport. It is a truly portable device which has great potential in the on-site assay. [ABSTRACT FROM AUTHOR]

A high mortality rate was found in cancer patients with distant metastasis. Development of targeted drugs for effectively inhibiting cancer metastasis is the key for increasing therapeutic success. In the current study, a folding paper system was developed to mimic a tumor–vascular interface for the study of long-distance cell migration. Correlation between the cell migration distance and metastasis-associated gene was successfully analyzed by disassembling the stacked paper construct. The result revealed that the migration distance and number of migrated cells were highly correlated to cell characteristics. Moreover, immunocytochemistry was directly conducted on the paper layer to study the signaling pathway. Kelch-like and protein tyrosine phosphatase families were examined and the PTPN13 gene was shown to regulate long-distance cell migration. By analyzing the phosphorylated mTOR, the PTPN13 gene was further confirmed to be a tumor suppressor gene that inhibits long-distance cell migration. The folding paper system provides an alternative approach for long-distance cell migration. Metastasis-associated gene expression can be analyzed to potentially develop targeted drugs for cancer metastasis inhibition. [ABSTRACT FROM AUTHOR]

Employing a one-pot Schiff-base condensation approach, the derivative "cholyl hydrazide Schiff base of phenothiazine" (ChHSB-PTZ) based on cholic acid has been synthesized and characterized via standard procedures. ChHSB-PTZ demonstrates exceptional sensitivity towards Sn(II) metal ion detection through fluorescence "turn-off" behavior based on chelation-enhanced fluorescence quenching (CHEQ) even in the presence of various cations and anions. Through modified Stern–Volmer and Stern–Volmer graph analyses, the binding constant (Ka) and limit of detection (LOD) were found to be 2.8 × 1010 M−1 and 2.2 nM, respectively. A 1 : 1 stoichiometry between ChHSB-PTZ and the Sn(II) metal ion was found via Job's plot. Moreover, the distribution of electronic states in the ChHSB-PTZ Schiff base and the sensing mechanism (CHEQ) were clarified through the use of 1H NMR titration spectroscopy and density functional theory (DFT) calculations. ChHSB-PTZ test paper strips are developed as an essential tool to improve the analytical applicability of the device and enable the rapid, accurate, and affordable detection of Sn(II) metal ions in environmental analysis. [ABSTRACT FROM AUTHOR]

A new analytical method for chronic kidney disease (CKD) detection utilizing paper spray mass spectrometry (PS-MS) combined with machine learning is presented. The analytical protocol is rapid and simple, based on metabolic profile alterations in urine. Anonymized raw urine samples were deposited (10 μL each) onto pointed PS-MS sample strips. Without waiting for the sample to dry, 75 μL of acetonitrile and high voltage were applied to the strips, using high resolution mass spectrometry measurement (15 s per sample) with polarity switching to detect a wide range of metabolites. Random forest machine learning was used to classify the resulting data. The diagnostic performance for the potential diagnosis of CKD was evaluated for accuracy, sensitivity, and specificity, achieving results >96% for the training data and >91% for validation and test data sets. Metabolites selected by the classification model as up- or down-regulated in healthy or CKD samples were tentatively identified and in agreement with previously reported literature. The potential utilization of this approach to discriminate albuminuria categories (normo, micro, and macroalbuminuria) was also demonstrated. This study indicates that PS-MS combined with machine learning has the potential to be used as a rapid and simple diagnostic tool for CKD. [ABSTRACT FROM AUTHOR]

Metal halide perovskite quantum dots (QDs) with unique physicochemical properties are promising candidates for next-generation optoelectronics, but they often suffer from stability issues that severely limit their potential for practical applications. In this work, we adopt an oleic acid/oleylamine-free approach to synthesize MAPbBr3 quantum dot (MQD) papers by incorporating MQDs into cellulose nanofiber frameworks. The abundant long-chain binding ligands containing sulfate terminal groups within the cellulose nanofiber remarkably stabilize the MQD structure, enabling the fabrication of self-power and flexible MQD paper photodetectors with a responsivity of ∼0.19 mA W−1, detectivity of 1.58 × 108 cm Hz1/2 W−1, and excellent bendability and reliability after 500 bending cycles. More importantly, these MQD/cellulose-based self-powered photodetectors demonstrate extraordinarily high environmental stability, maintaining more than 90% of the initial responsivity after 60 days. The simple disposability of the paper-based device is also illustrated by burning within one second, suggesting the ease of device elimination. Our work provides a unique approach to designing ultra-stable perovskite QD-based electronics with unprecedented functionalities. [ABSTRACT FROM AUTHOR]

A new method utilizing fluorescent ratiometry is proposed for detecting putrescine and spermidine. The method involves the use of a fluorescent probe comprising a 2D halide perovskite synthesized from octadecylamine-iodine and PbI2via a grinding-sonicating technique, along with a Eu3+-complex. Upon excitation at 290 nm, the probe fluoresces at two distinguishable wavelengths. The addition of putrescine and spermidine significantly decreases the emission of the 2D halide perovskite at 496 nm, while the emission of the Eu3+-complex at 618 nm remains stable. The color changes of the probe depend on the concentration of putrescine and spermidine, and the assay offers linearity over a wide concentration range (30–4000 ng mL−1), a low detection limit (4 ng mL−1 for putrescine, and 7 ng mL−1 for spermidine), and a quick response time. Furthermore, a portable device based on a smartphone can be used to record the color change of the paper test strip using the prepared fluorescent materials. The fluorescence quenching mechanism of the probe is explained as dynamic quenching. [ABSTRACT FROM AUTHOR]