Search

Vehicular ad hoc networks consist of self-organizing nodes using multi-hop wireless links for communication without any infrastructure support. Traditionally, ad hoc routing protocols use the minimum hop count for their routing metric since a smaller number of transmissions is typically equivalent to a higher throughput, lower delay, and minimal power consumption. However, with the muti-rate capability of emerging radio interfaces, e.g., 802.11ax/be standards, the min-hop metric no longer results in high throughput. For instance, if the higher data rate links are selected for the route, it could result in a higher throughput even if the route takes more hop counts. In this paper, we propose a high throughput routing scheme, called MARV, which makes two key contributions. MARV searches for high throughput paths using an on-demand route searching algorithm so that the routing overhead is smaller compared to other multi-rate-aware routing schemes. MARV also searches for multiple paths to maintain both min-hop and high-throughput paths to select the adequate path depending on the data packet size. We conduct simulations to demonstrate that MARV outperforms not only min-hop path metrics but also previously proposed high-throughput metrics.

The increasing demand for Internet of Things (IoT) applications has resulted in vast amounts of data, requiring the utilization of big data analytics. The integration of big data analytics in IoT-based smart cities can greatly benefit from the development of wireless communication protocols, among which the Thread protocol has emerged as a promising option. Thread is IEEE 802.15.4 based and has advanced capabilities like mesh networking, IPv6 support, and multiple gateways providing no single point of failure. This paper presents the design and evaluation of a low-cost mesh network using Raspberry Pi, nRF52840 dongle, and OpenThread 1.2 (i.e., an open-source software implementation of the Thread protocol stack). The research elaborates on the hardware and software solutions used, as well as the network topologies adopted. To evaluate the performance of the developed system, extensive real-time tests are performed, considering parameters, such as jitter, packet loss, and round trip time. These tests effectively demonstrate the effectiveness of the Thread network. Furthermore, the impact of varying payload size and bitrate on the network is analyzed to understand its influence. The behavior of the multi-hop network is also examined under link failure scenarios, providing insights into the network’s robustness. Our findings provide valuable insights for researchers interested in designing low-cost and efficient mesh networks for various IoT applications, including home automation, building/campus monitoring systems, distributed industrial IoT applications, and smart city infrastructure.

In recent years, low-power wide-area network (LPWAN) has received widespread popularity with long-range and wide-area communication at low power for the Internet of Things (IoT) systems. Among many vendors of LPWAN, long-range low-power wireless communications, also called LoRa, is one of the competing standards and is well known in both academia and industrial communities as an emerging research area. Among the LoRa applications, unmanned aerial vehicles (UAV) systems are emerging with the benefits of extended battery life and a long communication range. In this paper, we investigate the network capacity with the mixture of concurrent and sequential transmission (MCST) scheme over LoRa networks. From the simulation results, it can be seen that MCST is suitable for implementation in the LoRa network. Specifically, MCST can achieve higher throughput with low transmission latency and energy consumption compared to the existing CSMA approach LoRa MAC. Besides, we also propose a modified MCST over the LoRa (mMCST/LoRa) scheme to mitigate the transmission latency further. The simulation results reveal a better performance in terms of throughput, latency and energy consumption, regardless of the frame payload size and the number of nodes in the network.

Delay-tolerant networks (DTNs) are networks where there is no immediate connection between the source and the destination. Instead, nodes in these networks use a store–carry–forward method to route traffic. However, approaches that rely on flooding the network with unlimited copies of messages may not be effective if network resources are limited. On the other hand, quota-based approaches are more resource-efficient but can have low delivery rates and high delivery delays. This paper introduces the Enhanced Message Replication Technique (EMRT), which dynamically adjusts the number of message replicas based on a node’s ability to quickly disseminate the message. This decision is based on factors such as current connections, encounter history, buffer size history, time-to-live values, and energy. The EMRT is applied to three different quota-based protocols: Spray and Wait, Encounter-Based Routing (EBR), and the Destination-Based Routing Protocol (DBRP). The simulation results show that applying the EMRT to these protocols improves the delivery ratio, overhead ratio, and latency average. For example, when combined with Spray and Wait, EBR, and DBRP, the delivery probability is improved by 13%, 8%, and 10%, respectively, while the latency average is reduced by 51%, 14%, and 13%, respectively.