Search

Computer vision technology for the automatic recognition and geometric characterization of carbon and glass fibers in scanning electron microscopy images is proposed. The proposed pipeline, combining the SAM model and DeepLabV3+, provides the generalizability and accuracy of the foundational SAM model and the ability to quickly train on a small amount of data via the DeepLabV3+ model. The pipeline was trained several times more rapidly with lower requirements for computing resources than fine-tuning the SAM model, with comparable inference time. On the basis of the pipeline, an end-to-end technology for processing images of electron microscopic fibers was developed, the input of which is images with metadata and the output of which is statistics on the distribution of the geometric characteristics of the fibers. This innovation is of great practical importance for modeling the physical characteristics of materials. This paper proposes a few-shot training procedure for the DeepLabV3+/SAM pipeline, combining the training of the DeepLabV3+ model weights and the SAM model parameters. It allows effective training of the pipeline using only 37 real labeled images. The pipeline was then adapted to a new type of fiber and background using 15 additional real labeled images. This article also proposes a method for generating synthetic data for training neural network models, which improves the quality of segmentation by the IoU and PixAcc metrics from 0.943 and 0.949 to 0.953 and 0.959, i.e., by 1% on average. The developed pipeline significantly reduces the time required to evaluate fiber length in scanning electron microscope images. [ABSTRACT FROM AUTHOR]

This paper presents a comparative analysis of fiber aspect ratios using scanning electron microscopy (SEM) and the mean field homogenization approach. The novelty of this work lies in an effective fiber length evaluation based on a comparative analysis of fiber aspect ratios using scanning electron microscopy (SEM) and the mean field homogenization approach. This makes it possible to use an electron microscope to image fiber samples corresponding to the sample size using microtomography. Molded samples and pellets of four polyamide-6 short-glass fiber-reinforced composites with mass fractions of 15%, 30%, and 50% were considered. The aspect ratio distribution measured by SEM for the investigated materials was 20.25 with a coefficient of variation of 5.1%. The fiber aspect ratio obtained based on mean field homogenization theory and the tensile curve approximation was underestimated at 13.698 with a coefficient of variation of 5.2%. The deviation between the micro- and macro-estimates can be represented as a mean effective aspect ratio of 68% with a coefficient of variation of 8.5%. The developed technology for preparing samples for SEM and automated image processing can be used to study other short-reinforced polymer composite materials. The obtained estimates can serve as a useful reference when calibrating other models of short-fiber-reinforced polymer materials. [ABSTRACT FROM AUTHOR]

This paper discusses an approach to estimating the parameters of the cohesive zone model (CZM) by mode II by extruding the bushing along the lug axis. This method of evaluation requires small samples, which is particularly relevant when investigating short fiber-reinforced polymers (SFRPs) with additively manufactured embedded elements. Adhesion is investigated on the example of 30% carbon fiber-reinforced polyamide-6 molded to Ti-6Al-4V (VT6) selective laser-melted (SLM) alloy bushing in cases of a roughness Ra = 2.66 μm (vibratory finishing), Ra = 8.79 μm (sandblasting), and Ra = 10.02 (directly from SLM). The values of the maximum equivalent tangential contact stress were in a range from 1.1 MPa to 9.5 MPa, while the critical fracture energy for tangential slip was estimated at 15 N/mm for all cases. Experimental validation of the obtained CZM mode II was carried out by evaluating the load-carrying capacity of the lugs with different bushings. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The ribbed bushings added significant strength in the experiments, which confirmed the importance of considering the tangential mode in the contact model. The presented models can be used for the preliminary evaluation of short fiber-reinforced polyamide-6 parts with titanium-embedded elements bearing capacity. [ABSTRACT FROM AUTHOR]

A fully developed turbulent flow in a concentric annulus, Re = 10,000 , r i / r o = 0.5 , with an inner rotating cylinder in the velocity range N = U ω / U b = 0 ÷ 4 , is studied via a large-eddy simulation. Also, for comparison, simulations by steady-state, unstatiounary RANS k- ω SST (URANS), and Elliptic Blending Model (EBM) were made. The main focus of this study is on the effect of high rotation on the mean flow, turbulence statistics, and vortex structure. Distribution of the tangential velocity and the Reynolds stress tensor change their behaviour at N > 0.5 ∼ 1 . With rotation increases, the production of tangential fluctuation becomes dominant over axial ones and the position of turbulent kinetic energy maximum shifts towards the wall into the buffer zone. URANS and EBM approaches show good agreement with LES in mean flow, turbulent statistics, and integral parameters. The difference in pressure loss prediction between LES and URANS does not exceed 20%, but the average difference is about 11%. The EBM approach underestimates pressure losses up to 9% and on average not more than 5%. Vortex structures are described well by URANS. [ABSTRACT FROM AUTHOR]