Search

In this study, the microstructure of carbon fiber paper is modified through H 3 PO 4 etching to enhance the electrolyzer performance. The effects of different H 3 PO 4 concentrations and different soaking times on the hydrogen evolution reaction are firstly investigated. The electrochemical test results show that the best performance of etched electrodes is achieved at a H 3 PO 4 concentration of 1 M and a soaking time of 12 h, with a significant reduction in charge transfer resistance and overpotential. Subsequently, to explore the change mechanism in electrochemical properties, the microstructure of the carbon paper is investigated using Scanning Electron Microscope (SEM) and Mercury Intrusion Porosimetry (MIP) tests, which show uniformly distributed micropores appear on the surface of the carbon fibers after etching, and the porosity increases from 0.74 to 0.8. Brunauer-Emmett-Teller (BET) tests show that the specific surface area of the carbon paper increases from 0.72 m2/g to 4.06 m2/g, which effectively increases the interfacial contact area between the catalyst layer and the liquid gas diffusion layer. Furthermore, a 3D multi-physics model is established to further elucidate the impact mechanism of changes in porosity, conductivity, and active specific surface area on the performance of anion exchange membrane electrolyzer, with changes in active specific surface area having the greatest effect. • Microporous structure of the carbon paper LGDL is modified by etching. • The etching method effectively improves the performance of AEMEL. • The increase in specific surface area and porosity greatly reduces the resistance. • Numerical modeling to analyze the impact of microscopic parameters on AEMEL. • LGDL with high specific surface area has a positive effect on AEMEL's development. [ABSTRACT FROM AUTHOR]

Carbon fiber paper (CFP) is one of the most widely used gas diffusion layer materials for proton exchange membrane fuel cells (PEMFC) due to its excellent properties such as high conductivity, high strength, high air permeability and corrosion resistance. In this study, CFP was prepared using the phenolic resin (PF) in-pulp addition method. The effect of PF content on the properties of hot-pressed paper (HPP) and CFP was investigated. The results showed that when the dosage of polyethylene oxide (PEO) was 1.5 wt%, the flocculation effect of PEO on PF was basically complete, and the water filterability and retention of carbon fiber pulp were relatively optimal. After HPP was carbonized into CFP, the hydrophobicity, average pore size, porosity, and air permeability increased, while the resistivity and tensile strength decreased. With the increase of PF content, the tensile strength of CFP gradually increased, while the average pore size, porosity, air permeability and resistivity decreased. When the PF content was 250 wt%, the average pore size of CFP was 36.5 μm, the water contact angle was 127°, the porosity was 69.7%, the air permeability was 7.81 × 103 mL mm/(cm2·h·mmHg), the resistivity was 21.1 mΩ cm, and the tensile strength was 15.7 MPa. In addition, the CFP prepared using PF in-pulp addition method had a relativity uniform pore size distribution and high air permeability. Therefore, this work shows that the CFP prepared using this technique exhibits excellent comprehensive performance, and enables the manufacturing of CFP to be more efficient, low-cost, and environmentally friendly. [Display omitted] • Carbon fiber paper was prepared efficiently using the phenolic resin in-pulp addition method. • Polyethylene oxide exhibits strong adsorption ability on phenolic resin in carbon fiber pulp. • The melting temperature of phenolic resin is a critical point in the preparation process of carbon fiber paper. • Carbon fiber paper possesses a relatively uniform pore size distribution and high air permeability. [ABSTRACT FROM AUTHOR]

• Pulp and paper mill sludge (PPMS) landfill sites have GHG assessment challenges. • GHG fluxes measured by chambers with (F +) and without (F-) a frame were compared. • Flux relationships up to 80 % were shown between F- and F + chambers (the standard) • Correction factors for F- chambers were built to estimate fluxes from F + chambers. • The approach can refine GHG inventories on PPMS landfill sites. Assessments of greenhouse gas (GHG) emissions in managed areas are facing various challenges. A non-flow-through, non-steady-state (NFT-NSS) chamber coupled to a frame permanently inserted into the landfilled substrates is a standard method for quantifying GHG emissions in managed areas, such as pulp and paper mill sludge (PPMS) landfill sites. Frequent measurements are needed to minimize uncertainties on GHG emission factors at the landfill site scale. However, maintaining a frame inserted into the substrates for a long time period is often impossible due to landfilling management operations. Therefore, GHG measurements using NFT-NSS chambers placed directly on substrates' surface could be an interesting option. Our objectives were to determine the relationships between CO 2 , CH 4 , and N 2 O fluxes measured with (F +) and without (F-) a frame inserted in the substrates' surface and to develop correction factors for fluxes measured without a frame. Measurements were made at different PPMS landfill sites in the province of Québec, Canada. Stronger GHG flux relationships were observed at the provincial (across sites) than the specific site scale: the variance in GHG fluxes from F- chambers explained up to 80 % of variance in fluxes from F + chambers. The measured CO 2 , CH 4 , and N 2 O fluxes in F- chambers were on average 53, 78, and 63 % lower, respectively, than those estimated by the models at provincial scale. The correction factors developed with this approach could greatly extend the number of sites where in situ GHG measurements can be done and would help refining GHG inventories at the provincial and national levels. [ABSTRACT FROM AUTHOR]

Citation scores (CS) have been traditionally used to measure the impact of scientific publications. Sourced from the Internet, Altmetric Attention Scores (AAS) are complementary metrics that assess how often publications are discussed and used globally. We compared by rank the top 500 papers by CS and AAS published in Clinical Nutrition with corresponding AAS and CS. A search for all publications in Clinical Nutrition was performed on Dimensions (https://app.dimensions.ai/discover/publication) on 3rd April 2024. Outputs were ranked according to CS and then by AAS with the top 500 in each category selected. Scores, year and type of publication were recorded. Correlation was expressed as the Spearman's rank coefficient (ϱ). We identified 18,790 outputs. Within the top 500 publications ranked by CS, there was a significant weak positive correlation (ϱ = 0.235, P < 0.0001) between CS [median (IQR) 149 (116–223)] and AAS [7 (3–22)]. Ranked by AAS, there was a non-significant very weak positive correlation (ϱ = 0.072, P = 0.106) between AAS [55.5 (36–115)] and CS [42 (16.5–94.5)]. Trends remained similar when grouped by publication type. Guidelines, ranked by CS, had the highest CS and ranked by AAS, the highest CS and AAS. Publications per year, by year, ranked by CS, had a negatively skewed distribution peaking in 2012 and declined thereafter, but when ranked by AAS, had a moderately positive linear trend from 2001 to 2024 (ϱ = 0.513, P < 0.0001). Correlation between CS and AAS was weak. Guidelines had the highest CS and AAS. CS are iterative taking years to mature while AAS are immediate. [ABSTRACT FROM AUTHOR]

Carbon paper is one of the most widely used gas diffusion layer substrate materials due to its stable performance, relatively low cost, and easy for subsequent processing. Water-soluble phenolic resin, which is more ecologically friendly than alcohol-soluble phenolic resin, was used to prepare carbon paper as the precursor of the carbon matrix. And the effect of different resin solution concentrations on the properties of carbon paper was explored. The results showed that the graphitization, electrical conductivity and mechanical properties of carbon paper increased with the increase of resin solution concentration. When the concentration of resin solution was 20 wt%, the performance of carbon paper was relatively optimal. The graphitization of the carbon paper reached 65.45%, the porosity reached 80.74%, the resistance value at 1 MPa pressure was only 7.61 mΩ cm2, the tensile strength was 1.57 MPa, and the elastic modulus was 1210.98 MPa. [ABSTRACT FROM AUTHOR]

Carbon paper as a macroporous substrate of gas diffusion layer in proton exchange membrane fuel cells directly impacts the output performance of cells. In this study, we present a straightforward strategy to improve the overall performance of carbon paper by mixing short/long (6mm/10 mm) chopped carbon fibers at an optimal concentration of phenolic resin. The results show that incorporating longer carbon fibers can increase the porosity, conductivity, gas flux, and mechanical properties of carbon paper. The membrane electrode assembly achieved a peak power density of 1182.61 mW cm−2 at 60% RH using carbon paper with a long carbon fiber content of 40 wt% and an impregnation concentration of 10 wt%. This outperforms commercially available carbon paper. Based on electrochemical impedance spectroscopy results, it was confirmed that our carbon paper had a lower mass transfer resistance of only 32.17 mΩ cm−2 under conditions of 2 A cm−2 and 60% RH. This was due to its sparser three−dimensional network-like pore structure which was created by mixing different lengths (6mm/10 mm) of carbon fibers. This work provides new insights into preparing high−performance carbon papers. • The nature of carbon paper is regulated by mixing short/long (6mm/10 mm) CFs ratio. • The long carbon fiber contents of 20–40 wt% present better physical properties. • The optimal carbon papers can mitigate mass transfer resistance. • MEA composed of the optimal CP shows a higher power density than commercial CP. [ABSTRACT FROM AUTHOR]

A facile method is proposed in this work to prepare a carbon paper (CP) with outstanding properties by doping boron to catalyze graphitization at lower temperature. Boron was introduced into CP by impregnating carbon fiber preform into a boron/phenolic resin/ethanol solution, and then CP was obtained after the consecutive procedures of hot pressing, carbonization, and graphitization. Morphology, microstructure, composition, and physical properties of the doped and undoped CPs were thoroughly investigated via various techniques to exam the effects of boron concentration and graphitization temperature. Furthermore, the boron doped CP was fabricated into fuel cell gas diffusion layer (GDL) and membrane electrode assembly (MEA) to evaluate its performance through the single cell performance. The findings indicated CP doping with 2 wt% boron could lower the graphitization temperature by at least 200 °C. The B-doped GDL had a higher power density in comparison with the undoped GDLs made in our lab or from the commercial brands. • The innovative preparation method for carbon paper with high conductivity. • The effect of boron concentration and graphitization temperature on carbon paper. • The single cell performance of B-doped gas diffusion layer. [ABSTRACT FROM AUTHOR]

Development of low-cost, efficient, and stable oxygen evolution electrocatalysts is crucial for the conversion and storage of renewable energy. Therefore, an effective integrated heterostructure catalyst is needed to achieve a lower overpotential during oxygen evolution process. In this paper, cobalt-zinc bimetallic MOF precursors are used as templates to prepare bimetallic cobalt-based selenides with good oxygen evolution catalytic activity and stability on carbon fiber paper. Due to the high specific surface area and porous structure of the coupling structure of nanorods and polyhedra, and the strong electronic coupling between CoSe 2 and ZnSe on nanorods. CoSe 2 -ZnSe/CP exhibits excellent electrocatalytic activity in 1 M KOH solution. It only requires an overpotential of 275 mV to reach the current density of 10 mA cm-2, and the Tafel slope is 68.9 mV dec-1. In addition, after 12 h of continuous operation of CoSe 2 -ZnSe/CP, the activity decay of the catalyst is negligible. This work provides a method for the design of heterogeneous bimetallic selenide integrated oxygen evolution electrocatalysts. [Display omitted] • The CoSe 2 -ZnSe/CP catalyst is obtained by selenization of MOF precursor at high temperature. • The catalyst has unique nanorod-coupled polyhedral morphology and high specific surface area. • The strong electron coupling between CoSe 2 and ZnSe improves the oxygen evolution activity. • CoSe 2 -ZnSe/CP exhibits low overpotential, high exchange current density and fast kinetics. [ABSTRACT FROM AUTHOR]

The role of long-term parenteral support in patients with underlying benign conditions who do not have intestinal failure (IF) is contentious, not least since there are clear benefits in utilising the oral or enteral route for nutritional support. Furthermore, the risks of long-term home parenteral nutrition (HPN) are significant, with significant impacts on morbidity and mortality. There has, however, been a recent upsurge of the use of HPN in patients with conditions such as gastro-intestinal neuromuscular disorders, opioid bowel dysfunction, disorders of gut–brain interaction and possibly eating disorders, who do not have IF. As a result, the European Society of Clinical Nutrition and Metabolism (ESPEN), the European Society of Neuro-gastroenterology and Motility (ESNM) and the Rome Foundation for Disorders of Gut Brain Interaction felt that a position statement is required to clarify - and hopefully reduce the potential for harm associated with – the use of long-term parenteral support in patients without IF. Consensus opinion is that HPN should not be prescribed for patients without IF, where the oral and/or enteral route can be utilised. On the rare occasions that PN commencement is required to treat life-threatening malnutrition in conditions such as those listed above, it should only be prescribed for a time-limited period to achieve nutritional safety, while the wider multi-disciplinary team focus on more appropriate biopsychosocial holistic and rehabilitative approaches to manage the patient's primary underlying condition. [ABSTRACT FROM AUTHOR]

Enzymes derived from microbial sources have gained increasing popularity in industrial applications over the past decades. Despite the high production cost, alkaline proteases have wide applications in industries such as tanneries, food production, and detergents. In recent years, there has been a shift towards utilizing natural carbon sources for cultivating microorganisms and extracting proteases in order to reduce production costs. This study aimed to investigate the biochemical and kinetic properties of protease enzymes obtained from Aspergillus niger cultivated in a paper waste medium and compare with the enzyme produced in a basal medium. Glucose is a more favorable carbon source compared to cellulose, so paper waste was pretreated with cellulose-degrading bacteria to convert cellulose into smaller carbohydrates. After the growth of A. niger in basal and combinational media, the enzymatic properties were compared between the extracted enzymes by using casein as substrate. The results demonstrated that A. niger could produce protease enzymes in the paper waste medium similar to the basal medium with more than 5-fold cost saving. The specific activity of the enzymes isolated from the basal and paper waste media was calculated to be 184.95 ± 10.56 U ml−1 and 169.88 ± 11.05 U ml−1, respectively. Carbon sources did not affect the optimum pH and temperature of the protease enzyme, which were found to be 8 and 37 °C, respectively. This study provides valuable insights into the production of alkaline protease from A. niger using a combinational medium (paper waste pretreated by cellulose-degrading bacteria), offering a cost-effective approach for industrial applications. [ABSTRACT FROM AUTHOR]

This study conducts a comprehensive bibliometric analysis of highly cited papers in geosciences from 2013 to 2023, examining the temporal distribution of publications, the top 20 most cited papers, categorization by Web of Science categories (WC), journal distribution, and the relationship between open access and citation frequency. The analysis reveals significant growth in geoscientific research, particularly from 2016 onwards. Highly cited papers cover diverse and multidisciplinary topics, with leading journals identified as key dissemination platforms. The study also highlights the positive impact of open access on citation rates, emphasizing the importance of accessibility in enhancing research visibility and influence. These findings provide strategic guidance for researchers and institutions aiming to maximize the impact of their scientific contributions. [ABSTRACT FROM AUTHOR]

Paper mulching films are affected by wind and rain in the field, which lead to the problems of water absorption, shrinkage, and friction with the soil surface. In order to achieve better hydrophobic durability and wear resistance of paper mulching films, a paper mulching film with ZnO/SiO 2 composite coating was prepared by the brush coating method. Taking ceramic balls as friction pairs, reciprocating friction tests were carried out with two kinds of paper mulching films at different temperatures. The morphology of the raw paper mulch film and the ZnO/SiO 2 composite-coated paper mulch film after rubbing at different temperatures and the reason of the hydrophobic durability of the coated paper mulch film were analyzed using a scanning electron microscope and a three-dimensional topography instrument. The results show that ZnO/SiO 2 composite coating can improve the wear resistance and hydrophobic durability of the paper mulch film. Through surface morphology analysis, it can be found that the composite coating plays a role in modification and filling and improves the adhesion between the fibers by reducing the pores on the surface of the paper mulch film, finally improving the wear resistance and hydrophobic durability of the paper mulch film. [ABSTRACT FROM AUTHOR]