Search

Improving the thermoelectric (TE) properties of typical p-type Bi 0.5 Sb 1.5 Te 3 film is crucial for power generation in film-based thermoelectric devices. The shape of the hexagonal structure in the Bi 0.5 Sb 1.5 Te 3 film can be controlled by adjusting the magnetron sputtering parameters. The results indicate that a high nucleation rate under high sputtering power promotes island growth with a preferred orientation of (015). Thermal energy influences the growth in the in-plane direction along the (00 l) orientation and induces the c-axis orientation in the out-of-plane direction. Consequently, a dense layered hexagonal structure with a high grain boundary density is formed, leading to increased defect density, carrier concentration, and phonon scattering. In this case, the power factor reaches 3149.01 μW·m-1·K-2 at 480 K and the ZT value is 1.14 at 480 K. These results indicate that the film with a dense layered hexagonal structure enhances the TE properties. [ABSTRACT FROM AUTHOR]

In this work, the competitive relationship between the double amorphous phases is systematically investigated to increase the high-temperature wear resistance of the self-lubricating TiAlSiCN coating. These double amorphous phases combine the SiN x phase with high-temperature resistance and the C-related phase with a low friction coefficient. An increase in the Si content facilitates the change in the phase composition. The resultant coating exhibits an adhesion strength of 153 N, a friction coefficient of 0.24 and a hardness of 25.24 GPa upon generation of the TiAlN(C), the SiN x and the C-related phase. In this case, the TiAlSiCN coating achieves long-term self-lubrication at high temperatures with the titanium alloy friction pair. This mechanism stems from the SiN x phase replacing the portion of the easily oxidized amorphous C-related phase, which yields an enhanced high-temperature wear resistance. The cutting distance of this TiAlSiCN is 120% higher than that of the TiAlCN during the high-speed cutting of the titanium alloy. This outcome provides an effective solution for high-temperature applications of self-lubricating coatings. • Long-term self-lubricating is remained in TiAlSiCN coating by optimal Si content. • Synergistic effect of amorphous SiN x and C-related phase is solved in TiAlSiCN. • Tool life of TiAlSiCN improved 225% by comparing with that of TiAlN. [ABSTRACT FROM AUTHOR]

The self-lubricating TiAlTaCN coating with high-temperature resistance above 800 °C is developed using magnetron sputtering. This mechanism stems from the TaN phase is easily oxidized to form a protective Ta 2 O 5 that compensates for the insufficient antioxidant capacity of Al 2 O 3. Moreover, the TaC phase, being resistant to oxidation, contributes to achieving the self-lubrication effect with amorphous C-related phases. The cutting distance of the TiAlTaCN is 250% greater than that of the TiAlCN during the high-speed cutting of titanium alloy. These results reveal the oxidation mechanism of different carbon nitrides and provide a new solution for the self-lubricating coatings applied at high temperatures. • A new high-temperature resistant (800 °C) self-lubricating (COF=0.27) TiAlTaCN nanocomposite coating was prepared. • The Ta addition inhibits the phase transition and increases the high thermal stability from 600 °C to 1000 °C. • The wear rate of the TiAlTaCN is 38.7% lower than that of the TiAlCN at 600 °C. • The cutting distance of the TiAlTaCN is 250% higher than the TiAlCN during the high-speed cutting of titanium alloy. [ABSTRACT FROM AUTHOR]

[Display omitted] • The TiAlCN coating with high adhesion (156 N) and low friction coefficient (0.231) was deposited. • The TiAlCN coating can form a special structure of nano-crystalline wrapped by C-related amorphous phase by adjusting the C/N ratio. • The TiAlCN coating reduces wear and inhibits the adhesive wear during high-speed cutting titanium alloy. The cutting temperature will be significantly increased while cutting high reactive titanium alloy due to the large friction coefficient of the traditional TiAlN coated tools. The tool could also easily appear adhesive wear and thereby reduce the service life. In this work, TiAlCN coatings with high adhesion and low friction coefficient were deposited by changing the C 2 H 2 and N 2 flow rates and using medium-frequency magnetron sputtering. Compared with the TiAlN coating, the hardness of the TiAlCN coating increases up to the value of 20.36 GPa, the toughness is improved by about 230%, the adhesion reaches the value of 156 N. However, the friction coefficient is only 0.231. This performance improvement is attributed to the special structure of (Ti,Al)(C,N) nano-crystalline wrapped by a C-related amorphous phase that is formed in the coating. The structure can be formed by adjusting the C/N ratio to make the C atom content exceed the solid solubility but the C/N ratio does not reach saturation. This kind of TiAlCN coating reduces the wear and inhibits the adhesive wear during the high-speed cutting process of titanium alloy. The cutting distance is also increased by 50% compared with the TiAlN coating. [ABSTRACT FROM AUTHOR]