Search

Within the framework of radioactive waste management, the evolution of the gaseous composition inside the underground repository structures must be understood. Indeed, chemical and microbial reactions and exchanges occur between the rock, the structures and the air. These processes are studied in the Andra’s Meuse/Haute-Marne Underground Research Laboratory’s (URL). Recently, a gas monitoring station “Flair soil™” has been designed to monitor the gaseous composition inside this URL. This station is composed by two analyzers: a quadrupole mass spectrometer (QMS) which allows to follow the evolution of several gases and an infrared laser spectroscope (Picarro) providing simultaneous measurements of CH4, CO2 and CO. Thus, a multivariate calibration method for the quantitative detection of interfering and non-interfering gases in a nitrogen matrix has been developed for the QMS. The MS was calibrated from pure gases in a nitrogen matrix, with known concentrations and ion currents obtained from the measurement of each species of gas. This method uses matrix calculations to calculate the relative concentrations of an unknown gas mixture from the ion currents measured directly in the MS. The test gases T1 and T2 were used to assess the accuracy of the method. Daily ion currents are corrected from theoretical ion currents obtained from calibration coefficients and test gas concentrations. Some gases are less well quantified due to their low concentration in the test gases and interferences on the measured masses. One of the motivations of this study lay in developing an advanced measurement tool allowing to be low in sensitivity, and thus to improve the detection and quantification of gases at low concentrations. The objective of this paper is to propose an analytical method to measure the gaseous composition with several molecules. This method was able to detect hydrocarbons, noble gases, sulfides, greenhouse gases, oxygen, hydrogen, nitrogen in the same mixture.

This paper reports a study of water dynamics in a carbonate vadose zone (VZ). This study is performed in the experimental natural site of Saint-Emilion located in an underground quarry (Gironde, France). For this, two geophysical properties are used: the time domain reflectometry method (TDR) which provides the volumetric water content and electrical properties which provides the spatial water distribution. The dephasing and amplitude attenuation of the water content front were measured and modelled. Physical properties of the porous medium (porosity, permeability and effective diffusivity) can explain the water transfer process in VZ. The electrical resistivity tomography (ERT) gives a series of 2D images of water dynamics in VZ. Variations in water content induce changes in the electrical properties of the medium such as electrical resistivity. Using the time-lapse method, it is possible to model the evolution of saturation over time. The reliability of these electrical tools was confirmed by laboratory measurements.

The efficient and precise monitoring (detection, localization, and quantification) of fugitive methane (CH4) emissions is essential in preventing and mitigating greenhouse gas (GHG) emissions from oil and gas industrial facilities and landfills. Various strategies of mole fraction sampling within or in the vicinity of the sites and of atmospheric inversions have been developed for such a monitoring. Many studies have ensured the constant improvement of instrumentation, of measurement strategies and atmospheric inversion techniques.In this context, we participated in two controlled-release experiments at the TOTAL Anomaly Detection Initiatives (TADI) test site (Lacq, France) in October 2018 and 2019, dedicated to evaluate the ability of different local-scale atmospheric measurement and inverse modeling systems to localize and quantify point sources. We also conducted a series of 18 campaigns to regularly quantify methane emissions from the active “Butte-Bellot” landfill (about 35 km south-east of Paris) since 2018. We developed and applied different inversion approaches to process mobile or fixed-point measurements, which, in both cases, rely on a Gaussian dispersion model to simulate the atmospheric plume from the potential source location or mole fraction sensitivity at the measurement time and location to emissions at the potential source locations.The series of CH4 and carbon dioxide (CO2) controlled releases in TADI covered a wide range of release rates (~0.1 to 200 gCH4/s and 0.2 to 200 gCO2/s) and durations from 4 to 8 minutes (brief) to 25 to 75 minutes (longer). During the corresponding campaigns, we conducted both near-surface mobile and fixed-point (~2-4 m height) in situ atmospheric measurements based on Picarro CRDS, LGR (MGGA and UGGA), and LI-COR (LI-7810) instruments. Both inversions based on mobile measurements and those based on the fixed-point measurements provide estimates with a 20-30% average error for the CH4 and CO2 release rates, whatever the duration of the releases. The use of fixed-point measurements during long releases allow for a more precise localization of sources with an average location error of ~8m.The analysis of the CH4 mobile measurements at the “Butte-Bellot” landfill reveals the difficulties in exploiting measurements close to such a site with diffuse emissions whose spatial distribution is difficult to characterize, heterogeneous and highly variable in time. The series of estimates of the total CH4 emissions from the site based on remote mobile plume cross-sections, based on atmospheric inversions, are discussed.This presentation will highlight positive perspectives opened by the proposed inversion approaches and by our results and discuss options for further improvements when processing both types of measurements.

Methane (CH4) is a powerful greenhouse gas which plays a major role in climate change. The accurate monitoring of emissions from industrial facilities is needed to ensure efficient emission mitigation strategies. Local-scale atmospheric inversions are increasingly being used to provide estimates of the rates and/or locations of CH4 sources from industrial sites. They rely on local-scale atmospheric dispersion models, CH4 measurements and inversion approaches. Gaussian plume models have often been used for local-scale atmospheric dispersion modelling and inversions of emissions, because of their simplicity and good performance when used in a flat terrain and relatively constant mean wind conditions. However, even in such conditions, failure to account for wind and mole fraction variability can limit the ability to exploit the full potential of these measurements at high frequency.We study whether the accuracy of inversions can be increased by the use of more complex dispersion models. Our assessments are based on the analysis of 25 to 75-min CH4 controlled releases during a one-week campaign in October 2019 at the TOTAL’s TADI operative platform in Lacq, France (in a flat area). During this campaign, for each controlled release, we conducted near-surface in situ measurements of CH4 mole fraction from both a mobile vehicle and a circle of fixed points around the emission area. Our inversions based on a Gaussian model and either the mobile or fixed-point measurements both provided estimates of the release rates with 20-30% precision. Here we focus on comparisons between modeling and inversion results when using this Gaussian plume model, a Lagrangian model “GRAL” and a Gaussian puff model. The parameters for the three models are based on high-frequency meteorological values from a single stationary 3D sonic anemometer. GRAL should have relatively good skills under low-wind speed conditions. The Gaussian puff is a light implementation of time-dependent modeling and can be driven by high-frequency meteorological data. The performance of these dispersion models is evaluated with various metrics from the observation field that are relevant for the inversion. These analyses lead to the exploration of new types of definitions of the observational constraint for the inversions with the Gaussian puff model, when using the timeseries from fixed measurement points. The definitions explore a range of metrics in the time domain as well as in the frequency domain.Eventually, the Lagrangian model does not outperform the Gaussian plume model in these experiments, its application being notably limited by the short scales of the transport characteristics. On the other hand, the Gaussian puff model provides promising results for the inversion, in particular, in terms of comparison between the simulated and observed timeseries for fixed stations. Its performance when driven by a spatially uniform wind field is an incentive to explore the use of meteorological data from several sonic stations to parameterize its configuration. The fixed-point measurements are shown to allow for more robust inversions of the source location than the mobile measurements, with an average source localization error of the order of 10 m.

International audience; This work is part of the Aquifer CO2-Leak project and aims to understand, quantify and model the environmental impact of a CO2 leak on water quality in the carbonate freshwater aquifer as well as CO2-water-carbonate interactions. The experiment has been performed within an Oligocene carbonate underground quarry located in Saint-Emilion (France).A water charged with dissolved CO2 was injected in the aquifer through a borehole. Downstream, seven wells were fitted with in-situ probes which automatically measured physicochemical parameters. Periodic water samplings in all wells have been undertaken to determine the elemental concentrations by ion chromatography.The spread of CO2 in the groundwater was monitored as a function of time and was observed to influence the various physicochemical parameters. Five parameters seem to be excellent indicators for monitoring a gas plume during CO2 geological storage in regard to our results: electrical conductivity and pH, and Ca2+, HCO3−, and CO2(aq) concentrations.The interaction between CO2 and limestone is highlighted by a saturation index (SI) calculated with PhreeqC software. It shows (i) a slight trend to dissolution of calcite in the injection well (SI < 0) linked to the reaction process between CO2-H2O-CaCO3 and (ii) a transport process via diffusion for the observation wells with a SI≃0.The evolution of physicogeochemical signatures in the aquifer allows us to understand the reactive and transport processes that occur during the migration of a gasified water plume in the context of leakage from a geological storage reservoir. Our results will make possible to model a leakage in a complex natural reservoir.

International audience; Evidences for active fluid seepages have been discovered along the Zambezi continental slope (offshore Southern Mozambique). These seepages are mostly associated with pockmarks which are aligned along a trend parallel to the slope and running closely upstream of the headwall scarp of a wide zone of slope destabilization. Fluid seepages are interpreted as a potential trigger for the slope destabilization. Acoustic anomalies within the water column have been interpreted as related to moderate bubble seepages mostly located outside and only punctually inside the destabilization zone. Exploration with the SCAMPI towed camera system in the widest pockmark (diameter 200 m wide) has shown fluid seepages associated to authigenic carbonate crusts and possibly bacterial mats. These fluid seepages are also associated to the presence of chemiosynthetic organisms (Vesicomyidae and Thyasiridae bivalves, Siboglinidae tubeworms). The sampled gas in the sediment corresponds mainly to CH4 of microbial origin, generated by hydrogenotrophic methanogenesis from a substrate of organic origin, i.e. a conventional process of genesis of microbial gas in the marine domain. No evidence for thermogenic gas was detected. Another type of pockmarks has been observed within the core of the slope destabilization zone. Most of these pockmarks are inactive in terms of fluid seepage at present time and are associated to carbonate buildups forming chimney geometries. They probably correspond to diagenetic chimneys of former fluid migration pathways that have been exhumed during the mass sliding and the surrounding depression are related to recurrent activity of strong lateral slope currents which have scoured the sediments around. The spatial organization of the slope destabilization features is considered as representative of the temporal evolution of the landslide giving information about the dynamics of slope instability processes. This proposed evolution started by scattered seepages of formation water with dissolved gas. Then free gas seepages appeared notably in the upper part of the slope. This was followed by progressive shallow deformation in the sediments downslope of the main gas seepages. Finally, the whole slope was destabilized forming imbricated landslides exhuming locally former diagenetic chimneys.

This work is part of the Aquifer CO2-Leak project, started in 2018 for a 4-years duration and that aims at evaluating the impact of CO2 leakages from a geological storage site and developing new monitoring tools and methodologies. The present study aims to understand, quantify and model the environmental impact of a CO2 leak on water quality in the carbonate freshwater aquifer and understanding CO2-water-carbonate interactions.This research has been performed on an experimental site located in Saint-Emilion (Gironde, France), in an underground quarry within a 30-meter-thick carbonate formation dated to the Upper Oligocene. The facies vary from wackestone to grainstone, and are associated with high values of porosity (from 25 to 45%) and permeability (between 5 and 20 D). A gas mixture, composed of CO2 (90%), He (9%) and Kr (1%), was injected in the aquifer through a borehole located upstream hydraulic gradient. The total injected volume was 200 liters for 1h30.The seven other boreholes downstream in the injection well were fitted with in-situ probes which automatically measured pH, electrical conductivity, and CO2 fraction. Periodic water samplings have been undertaken, to determine the elementary concentrations by ionic chromatography. The spread of dissolved CO2 in the freshwater aquifer has influenced the physicochemical parameters at the various measurement points and thus has been followed in the time.The interaction between the CO2 and the limestones causes the dissolution of the calcite, releasing Ca2+ and CO32- in the solution, which are distributed between H2CO3, HCO3- and CO32-. The comparison of the results before and after the passage of the plume highlights a dissolved CO2 concentration increase, combined with an increase of electrical conductivity and temperature, as well as a decrease in pH values.The evolution of the physicogeochemical signature in the aquifer allow to understand the reactive and transport processes during a migration of a CO2 plume in a leakage context. The acquisition of these results will make possible to model a leakage in a complex natural reservoir. Electrical conductivity and pH measurements seem to be excellent indicators for monitoring a gas plume during CO2 geological storage. The laboratory analyzes lead to better understand the CO2-water-carbonate interactions produced at the field scale and the relationships with petrophysical properties.Batch measurements study the evolution of the electrical conductivity, monitored as a function of the CO2 concentrations. Comparison of experiments using only water, water and sand or water and limestone, have shown that only the presence of carbonate ions allows an increase in this geophysical parameter. By means of these different tools and measures, the propagation of a CO2 leak will be followed through the modification of physicochemical parameters in the aquifer. This should also change the electrical resistivity values across the unsaturated zone. The electrical resistivity tomography should be a complementary tool in order to support these results, and to represent a 3D image plus time of the CO2 plume.

An ultra-diffusive leakage experiment was performed on the pilot site of Saint-Emilion near Bordeaux in France. It consisted in the injection of 85% CO2 and 5% of each He, Kr and CH4 in a vertical well with a very low injection pressure. This study allowed the development of an automated tool that continuously monitored the gas phase within the vadose zone. Measurements showed that the gas plume had a heterogeneous spatial and temporal variation. Mathematical calculations performed on the time series of the gas species showed that diffusive transport mainly occurred in the porous media. However, every stage of the migration could not be driven by diffusive process as shown by the exponential regression. A non-identified transport mechanism may have occurred during the increase of concentration. He was proven to be a suitable temporal tracer for a CO2 leakage as it was a good temporal precursor. Even if the process was weaker than in the former injection experiments, Kr could show help foreseeing the extent of the gas plume within the pilot site. CH4 was also shown to be an excellent temporal precursor of CO2 arrival. The amount of gas migrating through the preferential path identified in the previous experiment was weaker than in the previous study. Moreover, the monitoring showed that a significant amount of injected gas migrated deeper in the vadose zone. The ratios CO2/Kr vs. CO2/He and the evolution of CO2/Kr, CO2/He and CO2/CH4 put in evidence three groups of probes. The first consists in the subsurface probes and is characterized by a potential reactive transport of CO2 through the vadose zone such as gas dissolution in the aqueous phase. The second group gathers the closest probes to the injection point and underlines a very slow return to baseline value through diffusion. The third group is characterized by a competition between the process occurring in the first and second group. Isotopic measurement of Kr could not bring relevant information about the CO2 fates into the vadose zone. However, it shows the possible presence of mechanism transport such as vertical flux and gravitational settlings. Observations from both of all the leakage experiment and future laboratory experiment could improve our understandings of the buffering zone and help to foresee CO2 leakage for future storage site.

Hydrothermal alteration batch experiments were conducted on olivine bearing mine tailings in order to investigate two potential valorization methods: the ex-situ CO2 sequestration and hydrogen production. The originality of this work lies in the simultaneous investigation of these two processes. We reacted powdered mine tailings with CO2-saturated water at three different sets of P/T conditions, 473 K/15 MPa, 523 K/30 MPa and 573 K/30 MPa. After 25 days of reaction, CO2 was sequestered in the form of Fe-bearing magnesite, (Mg,Fe)CO3 in all the experiments. Maximum carbonation yield was achieved at 523 K and 30 MPa, which was 53.8 wt.% of product, equivalent to the trapping of 320.5 g of CO2 per kg of mine tailings. Hydrogen gas was produced via the oxidation of Fe2+ in olivine. The highest quantity of hydrogen (H2) was produced at 573 K/30 MPa which was 0.57 g of H2 per kg of mine tailings. It suggests that the temperatures between 523 K and 540 K at pCO2 = 30 MPa are favorable for simultaneous ex-situ CO2 mineral sequestration and hydrogen production from New Caledonian mine tailings. The combined method of ex-situ CO2 storage and hydrogen production proposed by this study offsets 90% of New Caledonia's annual CO2 emissions while compensating ∼10% of New Caledonia's annual energy demand. More globally, it has implications for cost effective disposal of industrial CO2 emissions and production of hydrogen gas (clean energy) at a large scale; those two processes could be combined using the residual heat provided by a third one such as the high temperature smelting of ore.

The objective of the Aquifer-CO2Leak project is to get insights into carbon dioxide CO2 migration in aquifers within the context of Carbon Capture and Storage (CCS) and to test the different equipment necessary for CO2 monitoring. The underlying idea is to develop an experiment in the saturated zone (phreatic) of the underground limestone quarry located at Gironde department (France). It consists in injecting water, carrying dissolved gases (CO2 and krypton) and a fluorescent molecule, under controlled conditions. In this paper, we present the dimensioning study of the experiment by numerical simulations carried out using the simulator CooresFlow (IFPEN's in-house simulator for reactive transport in porous media). The important experiment parameters (injection flow rate, injected volume, the time to return in system equilibrium and wells location) were successfully estimated. In particular, the variation of species concentration in time and space was simulated and analyzed to define an experimental measurement schedule for the planned survey. Finally, a sensitivity analysis of the uncertain model parameters is presented. We found that the water table level and the dispersivity of the porous medium appear to be the most “sensitive” parameters.

Serpentinite-hosting mud volcanoes, located in the Marianna forearc subduction zone, were drilled during IODP Expedition 366. Recovered samples from Asùt Tesoru seamount provide new insights on the generation of organic matter in deep environments. Short-chain alcohols, volatile fatty acids and light hydrocarbons are produced within hyperalkaline pore fluids (pH 12.5) rich in H2. The stable isotope values of those species show heavy δ13C values, suggesting a formation process through Fischer-Tropsch-Type reactions. This close isotopic study brings new constraints on the reaction pathways leading to the formation of not only light hydrocarbons, but also of short-chain organic molecules. These compounds may serve as precursors of building blocks essential to life in deep oceanic settings.

International audience; From a natural underground cavity and two locations situated in a well, three CO 2 injections have been designed and performed under controlled conditions in order to study its migration along the carbonate vadose zone and to test geochemical and geophysical techniques. After the understanding of the natural CO 2 dynamics and the establishment of a baseline, some numerical simulations have been performed to help to optimize the monitoring strategy (spatially and temporally). A mixture of CO 2 + noble gases has been injected and the results show that CO 2 subsurface leakage can be anticipated thanks to these inert chemical gases used as tracers (He + Kr).The geochemical and geophysical monitoring approaches are very complementary.

A shallow CO 2 injection experiment was performed on a pilot site near Bordeaux, France, in February 2015. A gas mixture composed of approximatively 90% CO 2 and 5% of each He and Kr as gas tracers was injected through a vertical well, with low injection rate, at 1.80 m depth and into the carbonate vadose zone. A set of geochemical monitoring tools was installed in order to monitor the developing gas plume and to allow comparison between this experiment and a former release experiment which used a higher flow injection was made. Measurement showed a heterogeneous spatial and temporal variation of the gas plume. Difference in time arrival of peak concentration of He, Kr and CO 2 confirmed that diffusion alone did not occur in the porous media. Former studies mentioned advective flow drove through preferential paths. Both advection and diffusion flow may have been observed in the experiment. It also shows that the difference in molecular weights and the heterogeneity of the limestone could lead He to be used as a temporal tracer, and Kr as a spatial tracer as it allows us to estimate the extent of CO 2 plume. The ratios between the various gas components also indicate that a sizeable amount of CO 2 could be consumed before it reaches the subsurface, meaning that the vadose zone could be a buffering zone to CO 2 leakage. The comparison between this experiment and a former one with different injection condition revealed that the presence of advection is dependent of the heterogeneity of the limestone. However, the injection rate induces the amount of gas diffusing or/and advecting. Observations from both, our recent and a previous leakage experiment and future laboratory experiment could improve our understandings of the buffering zone and help to foresee CO 2 leakage for future storage site.