Search

This study investigates micropolar plates through the analysis of transmitted acoustic waves at various incident angles. Using a combined theoretical and experimental approach, we explore the non-classical elasto-dynamic behavior of these materials. Theoretical transmission coefficients are tailored to highlight generalized Lamb modes and a new type of vibration mode called micropolar modes, considering the constant thickness of the plate and the effects of material micropolarity on linear elasticity. Overlaying diverse transmission coefficients for different angles provides insight into micropolar behavior, aiding in the understanding of mode evolution in the frequency domain and the estimation of the critical angle. We employ two types of low-density closed-cell foams made from polystyrene (expanded in one case, extruded in the other), covering a frequency range from 4 to 60 kHz using a tweeter loudspeaker and a microphone integrated with a National Instruments acquisition system. Identification of the first vibration mode of the plates is facilitated by the frequency range rich in low frequencies. Additionally, all responses exhibit supersonic velocities with substantial attenuations. The originality of this paper is twofold: it provides theoretical predictions of micropolar modes, along with their experimental observations above a critical angle of incidence. Consequently, this research enriches our understanding of micropolar materials and their potential contribution to effective noise reduction strategies in acoustic engineering. [ABSTRACT FROM AUTHOR]

An acoustic reflectivity method is proposed for measuring the permeability or flow resistivity of air-saturated porous materials. In this method, a simplified expression of the reflection coefficient is derived in the Darcy's regime (low frequency range), which does not depend on frequency and porosity. Numerical simulations show that the reflection coefficient of a porous material can be approximated by its simplified expression obtained from its Taylor development to the first order. This approximation is good especially for resistive materials (of low permeability) and for the lower frequencies. The permeability is reconstructed by solving the inverse problem using waves reflected by plastic foam samples, at different frequency bandwidths in the Darcy regime. The proposed method has the advantage of being simple compared to the conventional methods that use experimental reflected data, and is complementary to the transmissivity method, which is more adapted to low resistive materials (high permeability). [ABSTRACT FROM AUTHOR]

The fully developed laminar flow of a viscous non-Newtonian fluid in a rough-walled pipe is considered. The fluid rheology is described by the power-law model (covering shear thinning, Newtonian, and shear thickening fluids). The rough surface of the pipe is considered to be fractal, and the surface roughness is measured using surface fractal dimensions. The main focus of this study lies in the theoretical investigation of the influence of the pipe surface roughness on the velocity profile and the Darcy friction factor of an incompressible non-Newtonian fluid. The plotted results demonstrate that shear thinning fluids are the most sensitive to the surface roughness compared with Newtonian and shear thickening fluids. For a particular value of the surface fractal dimension, there exists an intersection point where shear thinning, Newtonian, and shear thickening fluids behave the same way regarding the amplitude of the velocity profile and the friction factor. This approach has a variety of potential applications, for instance fluid dynamics in hydrology, blood flow in the cardiovascular system, and many industrial applications.

Objectives: (1) To analyze the preferential pathways of sound transmission and sound waves travelling properties in the skull and (2) to identify the location(s) on the skull where bone conduction to the cochlea is optimal., Study Design: Basic research Methods: Nine cadaveric heads were placed in an anechoic chamber and equipped with six Bone Anchored Hearing Aids (BAHA™) implants (Cochlear™, Sydney, NSW, Australia) and fifteen accelerometers. A laser velocimeter was used to measure cochlear response by placing a reflector on the round window. Different frequency sweeps were applied to each implant, and measurements were recorded simultaneously by the laser velocimeter and accelerometers., Results: Low-frequency sound waves mostly travel the frontal transmission pathways, and there is no clear predominant pattern for the high frequencies. The mean inter-aural time lag is 0.1 ms. Optimal sound transmission to the cochlea occurs between 1000 and 2500 Hz with a contralateral 5 to 10 dB attenuation. The implant location does not influence mean transmission to the cochlea., Conclusion: There is a pattern of transmission for low frequencies through a frontal pathway but none for high frequencies. We were also able to demonstrate that the localization of the BAHA™ implant on the skull had no significant impact on the sound transmission, either ipsi or contralaterally.

Ultrasound propagation in porous materials involves some higher order physical parameters whose importance depends on the acoustic characteristics of the materials. This article concerns the study of the influence of two parameters recently introduced, namely, the viscous and thermal surfaces, on the acoustic wave reflected by the first interface of a porous material with a rigid structure. These two parameters describe the fluid/structure interactions in a porous medium during the propagation of the acoustic wave in the high-frequency regime. Both viscous and thermal surfaces are involved in Laurent expansion, which is limited to the dynamic tortuosity and compressibility to a higher order and corrects the visco-thermal losses. A sensitivity study is performed on the modulus of the reflection coefficient at the first interface as a function of frequency and on the waveforms reflected by the porous material in the time domain. The results of this study show that highly absorbent porous materials are the most sensitive to viscous and thermal surfaces, which makes the consideration of these two parameters paramount for the characterization of highly absorbent porous materials using the waves reflected from the first interface.

Three series of binary, FeTi (Ti-rich), FeAl and TiAl (Al-rich) alloy samples were produced in an argon arc furnace. An annealing treatment of 72 h at 1000 °C was applied to the samples, giving rise to different equilibrium microstructures depending on chemical composition. Their mechanical properties were studied through the determination of elastic constants that measure the stiffness of the elaborated materials. Young's modulus of the binary alloys was determined using Resonance Ultrasonic Vibration (RUV). The accuracy of this technique was demonstrated. A scanning electron microscope (SEM) with an energy dispersive spectrometer (EDS) and X-ray diffraction (XRD) made it possible to identify intermetallic compounds FeTi and Fe 2 Ti, FeAl and Fe Al 2 , and TiAl and Ti Al 2 in respective systems Fe⁻Ti, Fe⁻Al, and Ti⁻Al. The link between their composition, microstructure, and elastic properties was established.

Precise but simple experimental and inverse methods allowing the recovery of mechanical material parameters are necessary for the exploration of materials with novel crystallographic structures and elastic properties, particularly for new materials and those existing only in theory. The alloys studied herein are of new atomic compositions. This paper reports an experimental study involving the synthesis and development of methods for the determination of the elastic properties of binary (Fe-Al, Fe-Ti and Ti-Al) and ternary (Fe-Ti-Al) intermetallic alloys with different concentrations of their individual constituents. The alloys studied were synthesized from high purity metals using an arc furnace with argon flow to ensure their uniformity and homogeneity. Precise but simple methods for the recovery of the elastic constants of the isotropic metals from resonant ultrasound vibration data were developed. These methods allowed the fine analysis of the relationships between the atomic concentration of a given constituent and the Young’s modulus or alloy density.

A method for the identification of the mechanical moduli and density of flexible, supple thermoplastic thin films placed on elastic substrates using ultrasonic waves has been developed. The composite medium immersed in a fluid host medium (water) was excited using a 50MHz transducer operating at normal incidence in reflection mode. Inverse problems involving experimental data pertaining to elastic wave propagation in the thin films on their substrates and theoretical fluid-solid interaction models for stratified media using elasticity theory were solved. Two configurations having different interface boundary conditions (BC) were modeled, transverse slip for the sliding contact interface in the case where the thin films were placed on the substrate without bonding; a bonded interface condition. The inverse problem for the recovery of the mechanical parameters were solved for the thin films under the bonded and slip BCs. Substrates made of different elastic materials having different geometries were also evaluated and their advantages discussed., (Copyright © 2017 Elsevier B.V. All rights reserved.)

This paper describes the fabrication process and the method to determine the membrane tension and defects of an inkjet-printed circular diaphragm. The membrane tension is an important parameter to design and fabricate an acoustic sensor and resonator with the highest sensitivity and selectivity over a determined range of frequency. During this work, the diaphragms are fabricated by inkjet printing of conductive silver ink on pre-strained Mylar thin films, and the membrane tension is determined using the resonant frequency obtained from its measured surface velocity response to an acoustic excitation. The membrane is excited by an acoustic pressure generated by a loudspeaker, and its displacement (response) is acquired using a laser Doppler vibrometer (LDV). The response of the fabricated membrane demonstrates good correlation with the numerical result. However, the inkjet-printed membrane exhibits undesired peaks, which appeared to be due to defects at their boundaries as observed from the scanning mode of LDV.

The objective of this work was to analyze the influence of compaction pressure on the intrinsic acoustic parameters (porosity, tortuosity, air-flow resistivity, viscous, and thermal characteristic lengths) of compressed earth blocks through their identification by solving an inverse acoustic wave transmission problem. A low frequency acoustic pipe (60-6000 Hz of length 22 m, internal diameter 3.4 cm) was used for the experimental characterization of the samples. The parameters were identified by the minimization of the difference between the transmissions coefficients data obtained in the pipe with that from an analytical interaction model in which the compressed earth blocks were considered as having rigid frames. The viscous and thermal effects in the pores were accounted for by employing the Johnson-Champoux-Allard-Lafarge model. The results obtained by inversion for high-density compressed earth blocks showed some discordance between the model and experiment especially for the high frequency limit of the acoustic characteristics studied. This was as a consequence of applying high compaction pressure rendering them very highly resistive therefore degrading the signal-to-noise ratios of the transmitted waves. The results showed that the airflow resistivity was very sensitive to the degree of the applied compaction pressure used to form the blocks.

A capacitive acoustic resonator developed by combining three-dimensional (3D) printing and two-dimensional (2D) printed electronics technique is described. During this work, a patterned bottom structure with rigid backplate and cavity is fabricated directly by a 3D printing method, and then a direct write inkjet printing technique has been employed to print a silver conductive layer. A novel approach has been used to fabricate a diaphragm for the acoustic sensor as well, where the conductive layer is inkjet-printed on a pre-stressed thin organic film. After assembly, the resulting structure contains an electrically conductive diaphragm positioned at a distance from a fixed bottom electrode separated by a spacer. Measurements confirm that the transducer acts as capacitor. The deflection of the diaphragm in response to the incident acoustic single was observed by a laser Doppler vibrometer and the corresponding change of capacitance has been calculated, which is then compared with the numerical result. Observation confirms that the device performs as a resonator and provides adequate sensitivity and selectivity at its resonance frequency.