Search

Coronavirus disease 2019 (COVID-19) as a severe acute respiratory syndrome infection has spread rapidly across the world since its emergence in 2019 and drastically altered our way of life. Patients who have recovered from COVID-19 may still face persisting respiratory damage from the virus, necessitating long-term supervision after discharge to closely assess pulmonary function during rehabilitation. Therefore, developing portable spirometers for pulmonary function tests is of great significance for convenient home-based monitoring during recovery. Here, we propose a wireless, portable pulmonary function monitor for rehabilitation care after COVID-19. It is composed of a breath-to-electrical (BTE) sensor, a signal processing circuit, and a Bluetooth communication unit. The BTE sensor, with a compact size and light weight of 2.5 cm3 and 1.8 g respectively, is capable of converting respiratory biomechanical motions into considerable electrical signals. The output signal stability is greater than 93% under 35%-81% humidity, which allows for ideal expiration airflow sensing. Through a wireless communication circuit system, the signals can be received by a mobile terminal and processed into important physiological parameters, such as forced expiratory volume in 1 s (FEV1) and forced vital capacity (FVC). The FEV1/FVC ratio is then calculated to further evaluate pulmonary function of testers. Through these measurement methods, the acquired pulmonary function parameters are shown to exhibit high accuracy (>97%) in comparison to a commercial spirometer. The practical design of the self-powered flow spirometer presents a low-cost and convenient method for pulmonary function monitoring during rehabilitation from COVID-19.

A new membrane-based triboelectric sensor (M-TES) is presented as a self-powered pressure change sensor. It generates a voltage induced by surface triboelectric charges in response to an air pressure change. Extremely high detection resolutions of 0.34 Pa and 0.16 Pa are achieved when the air pressure increases and decreases in a small region away from the ambient standard atmosphere pressure, respectively, indicating an excellent sensitivity. By integrating the M-TES with a signal processing unit, we demonstrate practical applications of the device in sensing footsteps, respirations, and heartbeat, which suggests widespread use of the M-TES in fields of security surveillance, chemical engineering, geography research, environment monitoring, and personal healthcare. [ABSTRACT FROM AUTHOR]

Thermoelectric generators (TEGs) operate in the presence of a temperature gradient, where the constituent thermoelectric (TE) material converts heat into electricity via the Seebeck effect. However, TE materials are characterized by a thermoelectric figure of merit (ZT) and/or power factor (PF), which often has a strong dependence on temperature. Thus, a single TE material spanning a given temperature range is unlikely to have an optimal ZT or PF across the entire range, leading to inefficient TEG performance. Compositionally graded organic–inorganic nanocomposites are demonstrated, where the composition of the TE nanocomposite can be systematically tuned along the length of the TEG, in order to optimize the PF along the applied temperature gradient. The nanocomposite composition is dynamically tuned by an aerosol‐jet printing method with controlled in situ mixing capability, thus enabling the realization of such compositionally graded thermoelectric composites (CG‐TECs). It is shown how CG‐TECs can be realized by varying the loading weight percentage of Bi2Te3 nanoparticles or Sb2Te3 nanoflakes within an organic conducting matrix using bespoke solution‐processable inks. The enhanced energy harvesting capability of these CG‐TECs from low‐grade waste heat (<100 °C) is demonstrated, highlighting the improvement in output power over single‐component TEGs. [ABSTRACT FROM AUTHOR]

Triboelectric motion sensors, based on the generation of a voltage across two dissimilar materials sliding across each other as a result of the triboelectric effect, have generated interest due to the relative simplicity of the typical grated device structures and materials required. However, these sensors are often limited by poor spatial and/or temporal resolution of motion due to limitations in achieving the required device feature sizes through conventional lithography or printing techniques. Furthermore, the reliance on metallic components that are relatively straightforward to pattern into fine features limits the possibility to develop transparent sensors. Polymers would allow for transparent devices, but these materials are significantly more difficult to pattern into fine features when compared to metals. Here, an aerosol‐jet printing (AJP) technique is used to develop triboelectric sensors using a wide variety of materials, including polymers, which can be directly printed into finely featured grated structures for enhanced sensitivity to displacement and speed of motion. A detailed investigation is presented highlighting the role of material selection and feature size in determining the overall resolution of the resulting motion sensor. A three‐channel rotary sensor is also presented, demonstrating the versatility of the AJP technique in developing more complex triboelectric motion sensors. Aerosol‐jet printing is used to develop triboelectric motion sensors, based on the generation of a voltage across two dissimilar materials sliding across each other as a result of the triboelectric effect. A wide variety of materials, including polymers, can be directly printed into fine‐featured grated structures for enhanced sensitivity to displacement and speed of motion. [ABSTRACT FROM AUTHOR]