Search

The articulator is a prerequisite device for the analysis of occlusion and prosthodontic treatment, and it is required to simulate patient jaw movements. This article describes the technique to obtain sagittal condylar inclination (SCI) using cone beam computed tomography (CBCT) data and intraoral scan of the protrusive interocclusal position. The SCI can be used on a virtual articulator in a computer-aided design software, and it can assist in the fabrication of prosthesis which is harmonious with the mandibular movement of individual patient.

PURPOSE The accuracy of denture bases was compared among injection molding, milling, and rapid prototyping (RP) fabricating method. MATERIALS AND METHODS The maxillary edentulous master cast was fabricated and round shaped four notches were formed. The cast was duplicated to ten casts and scanned. In the injection molding method, designed denture bases were milled from a wax block and fabricated using SR Ivocap injection system. Denture bases were milled from a pre-polymerized block in the milling method. In the RP method, denture bases were printed and post-cured. The intaglio surface of the base was scanned and surface matching software was used to measure inaccuracy. Measurements were performed between four notches and two points in the mid-palatal suture to evaluate inaccuracy. The palatine rugae resolution was evaluated. One-way analysis of variance was used for statistical analysis at α=.05. RESULTS No statistically significant differences in distances among four notches (P>.05). The accuracy of the injection molding method was lower than those of the other methods in two points of the mid-palatal suture significantly (P

Implant parallelism is rarely achieved, particularly when anatomic limitations are present. The problem of nonparallel implants has been addressed by using angled or bar abutments to compensate for the implant angulation. However, an angled abutment or bar attachment has disadvantages in terms of cost, laboratory process, and the maintenance of oral hygiene. In this clinical report, a solution for the management of an inclined implant is presented by using customized locator abutment fabricated by computer-aided design and computer-aided manufacturing (CAD-CAM).

Purpose: Rotational errors of implants can occur during two stages: when connecting impression copings with implants, and when connecting impression copings with analogs. The aim of this study was to determine ways to minimize these rotational errors. Materials and Methods: Three types of implants were prepared: a tissue-level implant with an internal octagon 8-degree Morse taper connection, a bone-level implant with an internal hex 11-degree Morse taper connection, and a bone-level implant with an external hex connection. Each complex (n = 10 per group) was composed of an implant, an impression coping, and an analog. Implants were embedded in resin blocks and connected with corresponding impression copings. Analogs that reproduced the position of the implants were created by means of a custom-made transfer jig, and rotational errors were measured between implants and analogs. Impression copings and analogs were connected by means of four methods: The impression coping was connected to the implant in a clockwise (CW) or a counterclockwise (CCW) direction before tightening, and the analogs were then connected with impression copings and tightened using a hemostat (Hs) or by hand (Hd). Results: The CW-Hs and CCW-Hd groups exhibited low rotational error (mean ± standard deviation 0.11 ± 0.21 and 0.19 ± 0.34 degrees, respectively), whereas the CW-Hd and CCW-Hs groups exhibited high rotational error (−1.80 ± 0.67 and 2.07 ± 0.75, respectively) in different directions. A strong association was observed between the tightening method and rotational error, and a weak association was observed between the connection type and rotational error. Conclusion: The CW-Hs method was found to be the most suitable for minimizing rotational error between implants and analogs.

Purpose The design of the attachment must provide an optimum stress distribution around the implant. In this study, for implant overdentures with a bar/clip attachment or a locator attachment, the stress transmitted to the implant in accordance with the change in the denture base length and the vertical pressure was measured and analyzed. Materials and methods Test model was created with epoxy resin. The strain gauges made a tight contact with implant surfaces. A universal testing machine was used to exert a vertical pressure on the mandibular implant overdenture and the strain rate of the implants was measured. Results Means and standard deviations of the maximum micro-deformation rates were determined. 1) Locator attachment: The implants on the working side generally showed higher strain than those on the non-working side. Tensile force was observed on the mesial surface of the implant on the working side, and the compressive force was applied to the buccal surface and on the surfaces of the implant on the non-working side. 2) Bar/clip attachment: The implants on the both non-working and working sides showed high strain; all surfaces except the mesial surface of the implant on the non-working side showed a compressive force. Conclusion To minimize the strain on implants in mandibular implant overdentures, the attachment of the implant should be carefully selected and the denture base should be extended as much as possible.

The aim of this study was to determine the stability of computer-aided design and manufacturing (CAD/CAM) and prefabricated abutment by measuring removal torque before and after cyclic loading.Three types of fixture and 2 types of abutments were used. Removable torque was measured after cyclic loading for 5000 cycles between 25 and 250 N for each group. The same procedure was performed twice.First, removal torque values (Newton centimeter) were measured for stock versus custom abutments as follows: group 1: 27.17 versus 26.67, group 2: 26.27 versus 26.33, and group 3: 37.33 versus 36.67. Second removal torque values (Newton centimeter) were also measured: group 1: 23 versus 23.5, group 2: 22.5 versus 22.33, and group 3: 32.67 versus 32.5. There was no significant difference between the stock and custom abutments in either the first or second removal torque values and also no significant difference among initial tightening torque, first or second removal torque (P0.05).With precise control of CAD/CAM abutments, good screw joint stability can be achieved.

The conventional method for impressions of flabby tissue uses modified trays and highly flowable materials, but mucostatic impressions are difficult to achieve due to the viscous and the elastic natures of impression materials. In this report, a technique is presented in which conventional impression and intraoral scanning for a fully edentulous patient with flabby tissue are combined. The definitive impression was obtained by applying appropriate pressure to each tissue area, and the denture can be maintained passively and stable at rest and during function.

Few studies have been reported on the scientific measurements of the thickness and dimensions of the posterior palatal seal (PPS) area. The purpose of this study is to measure and analyze the thickness of palatal mucosa by using a three-dimensional (3D) model reconstructed with computed tomography (CT) images and to present objective values by identifying the PPS area. The CT images were reconstructed as a 3D model by separating the maxillary palate mucosa and teeth. Each reconstructed model was analyzed and the thickness was measured at 93 crossing points of each divided plane. The dimension of the PPS area was measured and the right and left dimensions of the PPS area were compared. The thickness of the palatal mucosa was thicker toward the posterior area. The thickness increased in the lateral direction and decreased again. In the PPS area, the mean dimension between the rearmost of anterior border and the most posterior line was 2.19 mm and the mean dimension between the forefront of anterior border and the most posterior line was 5.19 mm in the right side and 5.16 mm in the left side. The mean dimension from the center of the palate to the right most forward point was 6.85 mm, and the left was 7.36 mm. The new measurement method of palatal mucosal thickness is noninvasive, accurate, and easy to store and study, so it can be used effectively in planning and manufacturing the maxillary complete denture in the digital workflows.

PURPOSE. The purpose of this study was to investigate the demographic patterns of maxillofacial prosthetic treatment to identify the characteristics and geographic distribution of patients with maxillofacial prosthetics in the capital region of Korea. MATERIALS AND METHODS. This retrospective analytical multicenter study was performed by chart reviews. This study included patients who visited the department of prosthodontics at four university dental hospitals for maxillofacial prosthetic rehabilitation. Patients with facial and congenital defects or with insufficient medical data were excluded. The patients were classified into three categories based on the location of the defect. Patients’ sex, age, and residential area were analyzed. Pearson’s chi-square test with a significance level of 0.05 was used to analyze the variables. RESULTS. Among 540 patients with maxillofacial prosthetics, there were 284 (52.59%) male patients and 256 (47.41%) female patients. The number of the patients varied greatly by hospital. Most patients were older than 70, and the most common defect was a hard palate defect. Chi-square analysis did not identify any significant differences in sex, age, and distance to hospital for any defect group (P>.05). CONCLUSION. The results of this study indicated that there was imbalance in the distribution of patients with maxillofacial prosthetic among the hospitals in the capital region of Korea. Considerations on specialists and insurance policies for the improvement of maxillofacial prosthetics in Korea are required. [J Adv Prosthodont 2016;8:229-34]

Reproducing soft tissue contours around a pontic area is important for the fabrication of an esthetic prosthesis, especially in the anterior area. A gingival model that precisely replicates the soft tissue structure around the pontic area can be easily obtained by taking a pick-up impression of an interim fixed dental prosthesis. After a working cast is fabricated using the customary technique, the pick-up model is superimposed onto the working model for the pontic area using computer-aided design and manufacturing (CAD/CAM). A definitive restoration using this technique would be well adapted to the pontic base, which is formed by the interim prosthesis.

Tooth extraction is a routine surgical procedure in dental treatment. As a wound healing process after tooth extraction, a saddle-shaped residual ridge forms due to bone formation in the extraction socket and localized bone resorption on the external surface of the jawbone. The residual ridge is subjected to continuous bone resorption with substantial differences among individuals. In some cases, it results in excessive bone atrophy, which complicates dental restorative treatment. This unique oral wound healing process may be influenced by factors that are specific to oral tissue. HIF expression is different in oral wound healing compared to that of skin wounds. The objective of this study was to examine a genetic association between SNP of the HIF-1α gene, which is known to have high genetic diversity, and the residual ridge resorption (RRR). Two hundred and two Korean subjects (70.80 ± 9.40 years) with partially or completely edentulous mandible were recruited, and edentulous mandibular bone height was measured following the protocol of the American College of Prosthodontists. The HIF-1α allele was directly sequenced in 24 subjects resulting in the variants over 5% frequency in 95% likelihood, whereas tag-SNPs were selected to perform analysis for the remaining population. Student’s t-test and ANOVA were used for statistical analysis to examine the association between the SNPs and the RRR. Four novel variants were discovered, and a minor allele of rs11549467 was associated with the RRR of the subjects (p = 0.028). rs11549467 increases HIF-1α transactivity, enhancing angiogenesis and increasing new vessel formation. Thus, rs11549467 may play an important role in the disturbed bone remodeling balance resulting in RRR. Results of this study may be useful in developing novel genetic diagnostic tests and identifying Koreans susceptible to developing excessive jawbone atrophy after dental extraction. Most importantly, early screening using genetic information will rescue susceptible patients from the vulnerable situation of excessive jawbone atrophy where no effective prosthetic treatment is available.

Reproducing soft tissue contours around a pontic area is important for the fabrication of an esthetic prosthesis, especially in the anterior area. A gingival model that precisely replicates the soft tissue structure around the pontic area can be easily obtained by taking a pick-up impression of an interim fixed dental prosthesis. After a working cast is fabricated using the customary technique, the pick-up model is superimposed onto the working model for the pontic area using computer-aided design and manufacturing (CAD/CAM). A definitive restoration using this technique would be well adapted to the pontic base, which is formed by the interim prosthesis.

Evaluating the cement space of various dental prostheses is important because it is related to the stability and retention of the prosthesis. However, a method for evaluating an overall cement space is complex. The purpose of this technique was to simplify the evaluation of prosthesis cement space by using a digital scanner. The form and thickness of the cement space could be simply recognized in any section the clinician or dental researcher wishes. Moreover, the cement space of several dental prostheses for the same abutment could also be precisely evaluated by superimposition. The method can be applied to various prosthodontic treatments.

목적: 인조골에 동일한 조건으로 식립한 임플란트에 대하여 타진방식의 임플란트 안정성 측정기기인 Periotest와 AnyCheck을 사용하여 안정성 수치를 측정함에 있어서, healing abutment의 높이와 타진각도의 변화에 따른 각 측정기기의 안정성 수치 차이를 조사하는 것이다. 재료 및 방법: 총 60개의 임플란트를 주문제작...

가철성 국소의치의 금속구조물을 제작하는 방법은 왁스 패턴을 제작하여 주조하는 lost wax technique이 주로 사용되어 왔으나, 디지털 기술의 발달로 서베잉과 금속구조물을 CAD (Computer aided design)로 디자인하여 제작할 수 있게 되었다. 여러 증례에서 CAD를 이용한 pattern의 프린팅 방식으로 얻은 레진 패턴이 구...

SUMMARY Esthetic rehabilitation of discolored anterior teeth is always a great challenge, especially in the presence of pathology. Fortunately, conservative management in the esthetic zone has become more feasible in compromised cases because of the development of restorative materials and advances in dental adhesives. This report presents a complicated case of a patient with tetracycline-related discoloration, multiple root resorption, and a periapical lesion. Treatment was conservative and used a natural tooth pontic and splinted porcelain laminate veneers.

Implant has been an effective treatment option for the patients with oligodontia. However, it still remains unclear when the implant should be placed. Skeletal growth that can appear even after the growth period can lead to infraocclusion of the implant which can cause functional or esthetic complications. In order to minimize these problems, definitive restorations should be placed after the functional and esthetic rehabilitation is achieved through the use of provisional restorations. Definitive restorations made with monolithic zirconia were created by replicating provisional restorations by using the latest CAD/CAM technology. These definitive restorations were delivered to the patient and clinical observation after the treatment showed satisfactory result. (J Korean Acad Prosthodont 2016;54:28-34)

심한 잔존치조제의 흡수와 의치지지조직의 손상을 동반한 총의치 난증례는 정확한 진단과 체계적인 치료계획 수립을 통해 보철물의 유지, 안정, 지지를 증진시켜야 한다. Provisional restoration은 총의치의 안정성을 다각도로 평가하고 환자와 치과의사의 피드백을 가능하게 하는 유용한 도구로서 사용될 수 있다. 본 증례에서는 진단용의치를 통해 인상면, 연마면, 교합면을 평가하여 의치의 안정성을 증대시키고 환자의 심미적 요구를 반영하여 최종의치로 이행하였으며 임상적으로 기능과 심미적인 측면에 있어서 만족할 만한 결과를 얻었기에 이를 보고하고자 한다. 【In fully edentulous cases, which are accompanied by severe residual ridge resorption and impairment of supporting tissues of complete dentures, proper diagnosis and systemic treatment planning are required for the improvement in retention, stability, and support of prosthesis. Provisional restoration, while it is unfamiliar in complete denture restoration, can be used as a valuable tool, which makes possible to evaluate the stability of complete dentures and receive feedback from patients in complex clinical situations. In this case, a provisional denture was used to improve stability of impression, polished, and occlusal surfaces of complete denture, and to consider esthetic requirements before final denture construction. The result was clinically satisfactory in terms of functional and esthetical aspects.】