Search

BACKGROUND: The manner in which shooters pull the trigger may significantly affect the shooter’s results. Shooting coaches are often not able to detect incorrect pull because of gun movement during the shot and recoil. OBJECTIVE: Development of the smart-textile based trigger pull monitoring system and demonstration of its ability to distinguish correct and wrong triggering techniques. METHODS: Two separated knitted resistive pressure sensors were integrated over III and II phalanges in the index finger fingerstall; single sensor was integrated over both III and II phalanges of the middle finger fingerstall. Resistance of the sensors was measured in a course of shots, performed by expert shooter, which simulated typical novice’s trigger pull errors. RESULTS: Sensors’ resistance recordings were made for following erroneous trigger pull motions: pulling of the trigger with index finger’s II phalanx instead of III; fast and jerky trigger pull (trigger tear-off); too fast release of the trigger after shot; and excessive grip force, applied by middle finger. For each type of erroneous movement, recordings waveforms included distinguishable features that characterised a particular type of error. CONCLUSIONS: The developed trigger pull monitoring system provides signals that could be used for recognition of the incorrect trigger pull motions during gun shots.

The results of investigations of initial n-4H–SiC structures by various methods are presented. The structures represent a highly doped n+ substrate with epitaxial layers 5 μm thick grown by chemical vapor deposition (CVD). The concentration of uncompensated donors in the epitaxial layer is in the range of Nd – Na = (1–50) × 1014 cm–3. Using the results of X-ray diffraction analysis, it is found that, in order to obtain efficient 4H–SiC ultraviolet photodetectors, it is desirable to have structures of epitaxial layers in which the effect of point-defect gettering, leading to an increase in the lifetime of charge carriers and in the values of quantum efficiency, is observed. The photosensitivity of the investigated samples significantly depends on the degree of imperfection of the CVD epitaxial layer, which results in a change in the lifetime of charge carriers and, as a consequence, in a change in the quantum efficiency of 4H–SiC ultraviolet photodetectors.

Movement retraining has proven to be a reliable way of treating compensatory movement faults, however, it is time-consuming and requires a lot of attention from a physiotherapist. Reliable movement retraining assistance system could enable patients to perform retraining exercises at home, thus increasing the possible exercise performance frequentness and consequently hasten the improvement. This paper describes a smart shirt system for movement retraining assistance. The smart shirt system is based on textile stretch sensors that are positioned over the typical movement fault sites for movement detection and monitoring. The information from the textile stretch sensors is used as visual feedback by the wearer for movement corrections. To verify the feasibility of the retraining assistance system, it was tested with a set of compensatory movement tests and retraining exercises. Each exercise was performed in a correct and incorrect manner, and the sensor measurement was analyzed to confirm the difference in measured signals between both cases. In total 11 exercises were performed to cover all of the typical compensatory movement sites, and for each retraining exercise, at least one sensor was identified, whose measurement could be used as feedback for the particular exercise.

Advanced version of DAid® Pressure Sock System (DPSS) for walking/running gait monitoring is proposed. The system enables to study in details time –related parameters of gait, such as foot strike time, stride/swing time, gradients of plantar loading/unloading, etc. both indoor and outdoor. A new method of data processing, analysis and representation is developed for such systems with limited quantity of sensors and implemented in DPSS software. The method considers the foot loading as a propagation of the plantar pressure wave, where separate sensors record amplitudes of pressure waves as reference points. Data processing includes scaling procedure that is based on application of sample entropy as the measure of sensors activity. Processed data are represented in the form of loading wave plots (WPs). WPs show load propagation across the sensors during the gait/stance. Developed system and method were tested for different types of walk/run and corresponding WPs were constructed and evaluated by sport medicine doctors. Good agreement between WPs – based analysis and diagnoses made by direct observation during walk/run tests confirms system efficacy and validity of results. Proposed method essentially simplifies gait studies and interpretation of the results.

The article substantiates the relevance and necessity of realizing the goal of a comprehensive study of the conditions and areas of moral development. It considers the main problems arising in the process of researching the moral education and development of the children with hearing impairments. It also discusses the problems of choice and application of methods in the diagnostics of moral development. The article systemizes the approaches to solving the issue of differentiating the criteria of moral development and reveals the significance of these criteria for deaf education activity. In the process of moral education, children with hearing impairment due to the peculiarities of their speech and cognitive development face problems and difficulties in understanding ethical issues, standards, concepts and rules. The results of a comprehensive study of the moral development of children with hearing impairment show uneven development of the components of different areas and their moral conscience; sources of moral knowledge are limited and insufficiently used, the ability to define ethical concepts is not precise, it is narrow and associative. In this regard, there is a need for special educational and correctional efforts, but the possibility of carrying out and the content of the moral development correction are currently the debatable issues. The article shows the contradictory criticism of the moral development. It also promotes the idea about the positive impact of the correction, and its value regarding the problems of moral education. It emphasizes the need to use a variety of educational tools in correctional and pedagogical work to activate the behavioral, axiological and cognitive areas in the process of the phased implementation of the moral development program.

Manual therapy is used to treat patients with neck pain, and mobilization techniques are practiced clinically by physiotherapists. To evaluate the effectiveness of therapy it is necessary to measure the applied manual therapy forces. We present the sensitive glove concept designed to measure the forces applied during therapy. The sensitive glove is equipped with multiple textile-based sensors connected by sewing technology, in which changes in electrical resistance were observed due to the applied force. The number and position of sensors were defined basing on the experience of manual therapists and practicable techniques. Glove fabrication technologies were tested practically – sensors were glued and sewn on the base material and simple conductive threads were sewn by hand and with a sewing machine. Technological solutions were evaluated both in terms of visual and technical aspects. The final version of the sensitive glove was assessed by an expert and recommendations were given for improving further prototypes.