Search

High-performance Lamb wave devices have a vast application prospect in modern wireless communication systems. This paper proposes a method of spurious mode suppression by reducing the overlap length of electrodes according to modal shapes. The AlN/Al0.8Sc0.2N composite film is used to achieve a trade-off between electromechanical coupling coefficient (k t 2) and Q factor. The finite-element analysis (FEA) is employed to study the performance of the lowest-order symmetric mode (S0) Lamb wave resonators (LWRs), and the FEA result shows a spurious mode in the impedance response. According to the results of modal shape analysis, the typical LWR, the LWR with the circle-shaped arrangement of electrodes, the LWR with the circle-shaped apodization, and the LWR with the arc-shaped apodization are fabricated to suppress the spurious mode and investigate the performance of the LWRs. The measurement results show that the spurious mode is effectively suppressed over a wide frequency range (1.9–2.2 GHz) by the three designed electrode configurations. The LWR with the circle-shaped apodization working at 2.023 GHz has a Qp factor of 955, a moderate k t 2 of 2.97%, a figure-of-merit (Q × k t 2) of 28.4, and a large value of f × Q × k t 2 (5.773 × 1010). Utilizing modal shapes to design the electrode configuration of LWRs can suppress spurious modes without significant performance deterioration. [ABSTRACT FROM AUTHOR]

Fluid-coupled Lamb waves (LWs) were proposed to facilitate the self-assembling of three-dimensional (3D) photonic crystals (PCs) in this work. Numerical models were constructed for proof-of-concept, and a fabrication set-up was developed for experimental demonstration. LWs were initially generated by a piezoelectric substrate. A couplant altered the propagating direction of these LWs to form the fluid-coupled LWs at a superstrate. The coffee-ring effect (CRE) of a suspension droplet on the superstrate was thus suppressed. The suspended nanospheres formed 3D PCs after the droplet dried out. Diversified PCs were fabricated using the developed set-up. Their transmittance spectra demonstrated the corresponding bandgap clearly. Advantages of utilizing fluid-coupled LWs for self-assembling 3D PCs include flexibility in excitation frequency, fabrication cost-effectiveness, acceptance for a passively oscillating substrate, and enlargement of sample area. [ABSTRACT FROM AUTHOR]

Lamb wave resonators (LWRs) exhibiting high-quality factors and clean spectra demonstrate promising applications in RF communication and sensing. This paper discusses the relationship between the spurious mode, the quality factor, and the effective electromechanical coupling factor of resonators. When the resonant frequency of the spurious mode is slightly below the parallel resonant frequency (fp), the quality factor at fp (Qp) decreases dramatically. To enhance Qp and suppress the spurious mode, the LWRs with busbars including only the top electrode (non-overlap busbars) and the LWRs with busbars incorporating both top and bottom electrodes (overlap busbars) are designed and fabricated. The LWR with 12 μm-wide overlap busbars exhibits a notable enhancement in Qp, elevating it from 553.76 to 1488.17 and suppresses the spurious mode simultaneously. This research introduces a promising approach to suppress the spurious mode and enhance the quality factor of Lamb wave resonators, thereby holding great potential for applications in sensors and mobile communication. [ABSTRACT FROM AUTHOR]

The objective of the study was to analyze the influence of coating treatments on sound propagation speeds in thin boards, along the longitudinal and radial directions of resonance wood. The samples studied were thin boards made of spruce and maple wood with dimensions of 240 mm × 80 mm × 4 mm (length × width × thickness) subjected to different coating treatments (oil-based varnish and alcohol varnish) as well as unvarnished samples, exposed to radiation UV, and specimens treated in the saline fog. The test method consisted of evaluating the propagation speeds of Lamb waves applied to thin plates, according to a semicircular test model, so that the results highlighted both the acoustic response in the longitudinal and radial directions as well as the variation in the anisotropy of the samples with the change in the sound propagation direction relative to wood fibers. Based on the statistical analysis, sound propagation speed profiles were obtained in each of the 38 directions analyzed for all wood samples. The results highlighted that the oil-based varnish led to a decrease in the speed of propagation in the radial direction, compared to the alcoholic varnish, whose major effect was in the longitudinal direction, on the spruce wood. On maple wood, increasing the number of varnish layers, regardless of the type of varnish, led to a decrease in the anisotropy ratio between the longitudinal and radial directions. [ABSTRACT FROM AUTHOR]

This paper introduces a novel design for a solar photovoltaic/thermal (PV/T) air collector that utilizes staggered fins. The collector features double-layer flow channels in the same direction, with the upper channel equipped with transparent wave plates, and the lower channel fitted with staggered fins. The paper includes a calculation scheme for wave plate heat balance. The numerical model of the collector is established and verified by experimental results. A numerical model is used to analyze the height combination of the upper and lower runner and the fin arrangement of the lower runner. The results indicate that, under the given environmental parameters, as the PV panel moves down, the overall air heat transfer capacity decreases. When the height combination of the upper/lower runner is 23 mm/105 mm, the maximum value is 53.741%. With the increase of fin spacing, the heat transfer capacity of the lower runner decreases. With the increase of the number of fin rows, the heat transfer capacity of the lower runner increases. When the equivalent diameter of the rectangular channel and the number of fin rows were 70 mm and 3 rows, respectively, the maximum solar energy comprehensive utilization efficiency was 56.261%. [ABSTRACT FROM AUTHOR]

Welded lap joints play a vital role in a wide range of engineering structures such as pipelines, storage tanks, pressure vessels, and ship hulls. This study aims to investigate the propagation of ultrasonic guided waves in steel welded lap joints for the baseline-free inspection of joint defects using the mode conversion of Lamb waves. The finite element method was used to simulate a single lap joint with common defects such as corrosion and disbonding. To identify the propagating wave modes, a wavenumber–frequency analysis was conducted using the 2D fast Fourier transform. The power loss of the transmitted modes was also determined to identify damage in the lap joints. The results indicate that the A0 incident in pristine conditions experienced significant transmission losses of about 9.5 dB compared to an attenuation of 2.8 dB for the S0 incident. The presence of corrosion was found to reduce these transmission losses by more than 28%. In contrast, introducing disbonding in the lap joint increased the transmission loss of the S0 incident, while a negligible loss was observed for the A0 incident. The mode-converted S0 (MC-S) and mode-converted A0 (MC-A0) incidents were found to exhibit a unique sensitivity to the presence of corrosion and disbonding. The results indicate that MC-S0 and MC-A0 as well as Lamb mode incidents interact differently in terms of corrosion and disbonding, providing a means to identify damage without relying on baseline signals. [ABSTRACT FROM AUTHOR]

A theoretical approach was applied to study the vibration of simple-supported submerged horizontal plate. The derived analytical solution was used to determine natural frequencies for a horizontal plate vibrating in fluid. The investigations were conducted for a very wide range of material density and elasticity modulus covering all materials used in engineering practice. Analysis shows that plate vibration frequency decreases with increasing plate width and draft, and decreases with decreasing plate thickness. Moreover, the results show that a substantial effect on vibration of submerged plate has mass of water above plate. The results also show that plate vibration frequency decreases with increasing plate material density and decreases with decreasing elasticity modulus. The dominant factors affecting the vibration of the submerged plate are the plate width, the plate thickness, and elasticity modulus. For moderate and low values of elasticity modulus, vibration frequency is becoming lower than frequency of water waves. This is very important because wave frequencies overlap with the natural plate vibration frequencies, which may lead to resonance and failure of a structure. The problem is that the overlap of plate vibration frequencies and wave frequencies occurs for very wide range of wave and plate parameters. Laboratory experiments confirm theoretical results. [ABSTRACT FROM AUTHOR]

The ice formation over the aerofoil structure of the aircraft wing has been an obstruction as they abrupt the airflow, acting as drag. The investigation will intend to determine ice accumulation on carbon fiber-reinforced polymer (CFRP), approximated as ice build-up on aircraft wings. The observation is carried out over quasi-isotropic composite laminates using ultrasonic-guided waves with a central working frequency regime of 100 kHz. The three-dimensional (3D) finite element (FE) simulations are performed to observe the scattering effect to explore the reflection site in the far field. This effect was quite prominent for different thicknesses of Glaze ice (G-Ice) and was found to be strongly linked with the wave propagation and dispersion effect. The scattering results for the reflection of Lamb mode, when it interacted with the G-Ice interface, were quite noteworthy along the angular region rather than on the center line, indicating that the scattering was more prominent due to the presence of a 45° or (− 45)-degree fiber orientation in that laminate. A similar but complex scattering phenomenon was observed for different stacking sequences where the wave propagation angle and its amplitude at the receiver nodes are found to be closely bound with the exponential decay in group/phase velocity for the ice thicknesses studied. The FE approach is verified, and the results are validated analytically. Analytically, we have investigated a much-closed approximation with the detectability obtained from three-dimensional studies. Where the dispersion study performed has also contributed to verifying the present investigation in the long wavelength limits. This study can reveal the various optimized locations for placing the sensor for ice detection and quantification, which can be further helpful for practical guided wave inspection in ice detection and its removal. [ABSTRACT FROM AUTHOR]

The analytical and geometrical conditions for the possible appearance of the infinite group velocity (IGV) points belonging to the dispersion curves of Lamb waves propagating in traction-free plates are studied by a combined method comprising Cauchy sextic formalism and the exponential fundamental matrix method. According to the obtained geometrical condition, the IGV corresponds to the coincidence of a tangent line to any of the dispersion curves with a straight line passing through the origin. The developed technique is demonstrated by applying to the analysis of Lamb wave dispersion in three-layered plates with a soft inner core. [ABSTRACT FROM AUTHOR]

Compact circularly‐polarized (CP) light sources are important for chirality‐based applications at the chip level. The CP light is conventionally generated by passing the linearly‐polarized (LP) one through quarter wave plates which are too thick for packed integrations. In this work, the in‐plane submicron phase shifter substitutes the quarter‐wave plate in the creation of CP light. After the lasing field of a holed microdisk is coupled into the nearby waveguide and phase shifter, it is guided into two grating couplers that output orthogonally LP waves vertically. The two LP waves are phase‐shifted by π/2$\pi /2$ and combine into the coherent CP radiation in the far‐field zone. Experimentally, the fabricated devices exhibit a degree of circular polarization as high as 74%. This device scheme is simple and effective in that it relies on no extrinsic materials, large‐area auxiliary structures, or specialized operation conditions critical for CP radiation. The compatibility issues for integrated photonic systems are of less concern in such schemes. [ABSTRACT FROM AUTHOR]

Lamb wave-based damage quantification in large-scale composites has always been one of the concerning and intractable problems in aircraft structural health monitoring. In recent years, machine learning (ML) algorithms have been utilized to deeply explore the damage feature of Lamb wave signals, which aims to enhance the precision and accuracy of damage quantification. However, multi-damage quantification becomes one of the bottleneck problems because ML algorithms critically depend on the dataset. In this paper, a prioritizing selection and orderly permutation method is proposed to construct multi-damage dataset based on Born approximation principle, which shows the interaction between wave signals under multi- and single-damage conditions. Based on the multi-damage dataset, a multi-task deep learning algorithm is introduced to identify multiple damage, including the damage number, location, and size, in composite laminates. In the algorithm, a multi-branch 1D-convolution neural network framework, which includes a trunk network and branch networks is established to explore the damage features in Lamb wave scattering signals. Compared with single-task models, it has the ability to learn shared features for multiple tasks, effectively boosting the task results. The results show that the proposed multi-task learning (MTL) method saves 23.03% training time compared with the single-task learning method. In the task of quantifying multiple damage of composite laminate, the results of MTL are good for both the constructed test set and the measured test set, especially in the quantification of damage size, which shows the feasibility and reliability of this method. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Southeast University (English Edition) is the property of Journal of Southeast University Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The dual frequency Global Navigation Satellite System (GNSS) observations could determine the total electron content (TEC) in the ionosphere. In this study, GNSS TEC was applied to detect traveling ionospheric disturbances (TIDs) after the eruption of Hunga Tonga–Hunga Ha'apai (HTHH) on 15 January 2022. The eruption caused two types of tsunamis, first is tsunami generated by atmospheric wave (meteo‐tsunami) and second is caused by eruption induces water displacement or tsunami classic. At the same time with former tsunami, the atmospheric wave (shock and lamb waves) also caused TIDs at a speed of approximately ∼0.3 km/s. We found moderate correlation between this TIDs amplitude and the tsunami wave height model from tide gauge stations in New Zealand (0.64) and Australia (0.65). Further we attempted to reveal 3D structure of the TIDs in New Zealand, South Australia, and Philippines using 3D tomography. The tomography was set up > 1,170 blocks, as large as 1.0° (east–west) × 1.0° (north–south) × 100 km (vertical), up to 600 km altitude over selected regions. Tomogram shows beautiful concentric directivity of the first TIDs generated by atmospheric wave (AW). Key Points: 3D ionospheric disturbances during the 2022 Tonga eruption was investigated with spatial and temporal directionThe highest concentration of the electron disturbances was observed at an altitude of 200–300 km, which decreased at 500–600 kmA correlation between ionospheric disturbances and the height of tsunami associated with eruption was observed [ABSTRACT FROM AUTHOR]

This paper presents research on the application of ultrasonic-guided wave technology in corrosion defect identification, expounds the relevant ultrasonic-guided wave theories and the principle of ultrasonic-guided wave non-destructive testing of pipelines, and discusses the Lamb wave and shear horizontal wave mode selection that is commonly used in ultrasonic-guided wave corrosion detection. Furthermore, research progress in the field of ultrasonic-guided wave non-destructive testing (NDT) technology, i.e., regarding transducers, structural health monitoring, convolutional neural networks, machine learning, and other fields, is reviewed. Finally, the future prospects of ultrasonic-guided wave NDT technology are discussed. [ABSTRACT FROM AUTHOR]

Acoustoelasticity, a characteristic of material anharmonicity, gives rise to a link between wave propagation velocity and the stress state in materials. Ultrasonic techniques to monitor this coupling, particularly with high sensitivity and in a noncontact manner, can have widespread application both in the quantification of applied and residual stress and in the characterization of nonlinear material behavior through measurement of higher order elastic constants. Here, we use a laser ultrasonic technique to excite and detect zero group velocity (ZGV) Lamb wave resonances in aluminum plates under uniaxial loading. A laser line source is used to excite these resonances at different orientations with respect to the applied load, and the signals are detected using an interferometer. The effects of stress and source orientation on ZGV resonance frequencies are validated using the theory of acoustoelastic Lamb wave propagation. In addition, a model-based inversion technique is used to extract Murnaghan's third-order elastic constants from measurements of the stress dependence of the first two ZGV modes generated parallel and perpendicular to the applied load. Laser generation and detection of ZGV resonances is shown to be an effective and powerful approach for the noncontact and nondestructive acoustoelastic characterization of elastic waveguides. [ABSTRACT FROM AUTHOR]

We use high temporal‐resolution mesoscale imagery from the Geostationary Operational Environmental Satellite‐R (GOES‐R) series to track the Lamb and gravity waves generated by the 15 January 2022 Hunga Tonga‐Hunga Ha'apai eruption. The 1‐min cadence of these limited area (∼1,000×1,000 km2) brightness temperatures ensures an order of magnitude better temporal sampling than full‐disk imagery available at 10‐min or 15‐min cadence. The wave patterns are visualized in brightness temperature image differences, which represent the time derivative of the full waveform with the level of temporal aliasing being determined by the imaging cadence. Consequently, the mesoscale data highlight short‐period variations, while the full‐disk data capture the long‐period wave packet envelope. The full temperature anomaly waveform, however, can be reconstructed reasonably well from the mesoscale waveform derivatives. The reconstructed temperature anomaly waveform essentially traces the surface pressure anomaly waveform. The 1‐min imagery reveals waves with ∼40–80 km wavelengths, which trail the primary Lamb pulse emitted at ∼04:29 UTC. Their estimated propagation speed is ∼315 ± 15 m s−1, resulting in typical periods of 2.1–4.2 min. Weaker Lamb waves were also generated by the last major eruption at ∼08:40–08:45 UTC, which were, however, only identified in the near field but not in the far field. We also noted wind effects such as mean flow advection in the propagation of concentric gravity wave rings and observed gravity waves traveling near their theoretical maximum speed. Plain Language Summary: The record‐setting eruption of the Hunga Tonga‐Hunga Ha'apai volcano on 15 January 2022 was observed by geostationary satellites, which take an image of the full Earth disk every 10–15 min. Several smaller areas (∼1,000 km on a side) are, however, imaged every 1 min. The eruption generated various waves in the atmosphere, including acoustic waves traveling at the speed of sound and slower gravity waves. These atmospheric waves can be tracked by the subtle brightness temperature changes they cause in the images. We show that the 1‐min images used in our study capture finer details of the wave patterns and allow a better estimation of wave properties than the relatively infrequent full disk images. The high temporal frequency imagery also allows to determine the eruption sequence more precisely and reveal how the background winds affect the propagation of the waves. Key Points: Propagation of surface pressure anomalies explains the Lamb waveform derivative patterns seen in brightness temperature image differences1‐min mesoscale imagery depicts the short‐period variations within the long‐period wave packet envelope captured in full disk imageryThe Lamb wave train appears dispersive, main pulse is followed by waves with decreasing wavelength of ∼40–80 km and period of ∼2.1–4.2 min [ABSTRACT FROM AUTHOR]

Lamb wave detection is increasingly being utilized in the industry due to its extensive coverage area, high signal detection efficiency, and ease of operation. This paper offers a quantitative review of eight signal transformation methods utilized for de-noising and time-frequency analysis of Lamb waves, which include Fourier transform (FT), singular value decomposition (SVD), short-time Fourier transform (STFT), Wigner–Ville distribution (WVD), wavelet transform (WT), S-transform, Hilbert–Huang transform (HHT), as well as empirical mode decomposition (EMD) and its improved algorithms. The performances of signal transformations on denoising and defect location are assessed quantitatively using the signal-to-noise ratio (SNR) and time-of-flight (ToF). The results demonstrate that the complete ensemble EMD with adaptive noise (CEEMDAN) is able to suppress noise effectively while maintaining the primary features of the signal in an adaptive manner. Additionally, the continuous WT can obtain a more accurate time-frequency distribution, thereby providing the superior analytical ability for dispersive lamb wave signals with respect to positioning on the time axis. [ABSTRACT FROM AUTHOR]

We present the requirements, design, and evaluation of the cryogenic continuously rotating half-wave plate (CHWP) for the Simons Observatory (SO). SO is a cosmic microwave background polarization experiment at Parque Astronómico de Atacama in northern Chile that covers a wide range of angular scales using both small (⌀ 0.42 m) and large (⌀ 6 m) aperture telescopes. In particular, the small aperture telescopes (SATs) focus on large angular scales for primordial B-mode polarization. To this end, the SATs employ a CHWP to modulate the polarization of the incident light at 8 Hz, suppressing atmospheric 1/f noise and mitigating systematic uncertainties that would otherwise arise due to the differential response of detectors sensitive to orthogonal polarizations. The CHWP consists of a 505 mm diameter achromatic sapphire HWP and a cryogenic rotation mechanism, both of which are cooled down to ∼50 K to reduce detector thermal loading. Under normal operation, the HWP is suspended by a superconducting magnetic bearing and rotates with a constant 2 Hz frequency, controlled by an electromagnetic synchronous motor. We find that the number of superconductors and the number of magnets that make up the superconducting magnetic bearing are important design parameters, especially for the rotation mechanism's vibration performance. The rotation angle is detected through an angular encoder with a noise level of 0.07 μrad s . During a cooldown process, the rotor is held in place by a grip-and-release mechanism that serves as both an alignment device and a thermal path. In this paper, we provide an overview of the SO SAT CHWP: its requirements, hardware design, and laboratory performance. [ABSTRACT FROM AUTHOR]

During production or service life, lightweight components made of fibre-reinforced polymers (FRP) may suffer from different types of defects such as cracks or delamination, which may be detected, amongst others, with the help of ultrasonic lamb waves (LW). The study intends to illustrate the potentials of numerical models to assist the design of LW-based non-destructive testing (NDT) processes. For that, the complete NDT chain of an LW driven inspection system was supported by a Finite Element Analysis (FEA) using stringer-stiffened C FRP panels as an exemplary component. The study was divided in two publications: The first part focused on the description of the numerical model, illustration of its functionalities and – most importantly – the determination of LW related effects that were needed to design the inspection system (dispersion characteristics, excitation frequency, propagating modes etc.). In this part, the FEA driven design approach was first validated with self measured experimental data as well as experiments provided in literature. In the second step, the numerical model was applied for the performance of parameter studies in order to identify component specific aspects that proved important for the NDT process. Finally, general advices and FEA related working steps were derived from all findings to assist practitioners in the implementation of the technique. [ABSTRACT FROM AUTHOR]

The piezoelectric thin film composed of single-crystal lithium niobate (LiNbO3) exhibits a remarkably high electromechanical coupling coefficient and minimal intrinsic losses, making it an optimal material for fabricating bulk acoustic wave resonators. However, contemporary first-order antisymmetric (A1) Lamb mode resonators based on LiNbO3 thin films face specific challenges, such as inadequate mechanical stability, limited power capacity, and the presence of multiple spurious modes, which restrict their applicability in a broader context. In this paper, we present an innovative design for A1 Lamb mode resonators that incorporates a support-pillar structure. Integration of support pillars enables the dissipation of spurious wave energy to the substrate, effectively mitigating unwanted spurious modes. Additionally, this novel approach involves anchoring the piezoelectric thin film to a supportive framework, consequently enhancing mechanical stability while simultaneously improving the heat dissipation capabilities of the core. [ABSTRACT FROM AUTHOR]

Purpose: In this paper, the free vibration and dynamic response of laminated composite wave plate in a thermal environment are investigated by means of the mesh-free strong form method. Method: The wave plate is divided into several rectangular and cylindrical segments, and each segment is transformed into a square domain or equivalent cylindrical rectangular domain through a coordinate mapping technique to ensure numerical stability. The theoretical formulation of the individual segment is established using Hamilton's principle in the framework of first-order shear deformation theory (FSDT), and the thermal effects on the wave plate are considered by employing the thermo-elastic theory. The discretized equations are obtained directly from the strong forms of governing equations in which displacement components are approximated by a mes-hfree Tchebychev-radial point interpolation method (TRPIM) shape function. The formulation of the entire wave plate is obtained using coupling conditions between the segments. The harmonic distributed load and stationary/nonstationary stochastic excitation are considered as the external force. Results: Convergence and verification studies are performed to confirm the reliability and accuracy of the present formulation. Satisfactory agreements are achieved between the numerical results of the proposed method and those from the published literature. Finally, the effect of some parameters on the free vibration and dynamic response of laminated composite wave plate is presented. [ABSTRACT FROM AUTHOR]

In this experimental investigation, we explore the propagation characteristics of surface Rayleigh waves in a Locally Resonant Metamaterial (LRM) layer positioned on an elastic half-space. The study focuses on characterizing the dispersion and attenuation properties of these waves and validating analytical and numerical models of the LRM. For practical purposes, we utilize a thin-plate sample and construct the LRM layer, featuring multiple rows of sub-wavelength resonators, by machining the resonators at one edge of the plate. Employing a piezoelectric transducer coupled to the plate and a laser vibrometer, we actuate and receive the surface-like waves propagating at the plate edge. Two resonant layer configurations, comprising 3 and 5 rows of resonators, corresponding to heights of ∼0.6λh and λh, where λh represents the reference wavelength of Rayleigh waves, are examined. The experimental observations reveal the hybridization of the fundamental surface mode at the resonant frequency of the embedded resonators, leading to the creation of a low-frequency bandgap. This bandgap, attributed to the local resonance mechanism, exhibits a remarkable attenuation of surface wave amplitudes. To support our experimental findings, we conduct both analytical and numerical studies. These analyses demonstrate the confinement of the lowest-order surface mode within the frequency ranges proximate to the resonators' resonance. The insights gained from this experimental study contribute to the advancement of strategies for mitigating surface waves through the application of resonant metamaterials and metastructures. [ABSTRACT FROM AUTHOR]

This study presents the observation and evaluation of a meteotsunami in the Indian Ocean triggered by the Hunga‐Tonga volcanic eruption. The event was detected through tide gauges and bottom‐pressure recordings across the Indian Ocean, with an amplitude of 10–15 cm, lasting for a few days. A numerical model was used to understand the ocean's response to meteotsunami and evaluate the dynamics behind it. The model results show that the sea‐level oscillations result from the ocean waves generated by a propagating Lamb wave. In addition to interaction with bathymetry, refracted and reflected waves also determine the sea‐level variability. Our analysis shows that bathymetric slope plays a vital role in near‐shore processes. The spectral and spatial characteristics of the meteotsunami were reminiscent of seismic tsunamis. Our research on this rare event elucidates the unresolved issues and eventually leads to designing a blueprint for future observation and modeling of meteotsunamis and seismic tsunamis. Plain Language Summary: This study evaluates the observation of a rare meteotsunami event that occurred in the Indian Ocean. An atmospheric pressure wave generated by the eruption of the Hunga‐Tonga volcano in the Pacific Ocean caused the meteotsunami. The signatures of this event were captured by tide gauges installed along the coast and pressure recorders moored at the ocean floor. We demonstrate using a numerical model that fast‐moving atmospheric pressure waves, Lamb waves, caused the sea‐level oscillations. Interactions with bathymetry further influenced sea‐level variability in the basin, reflected waves, and refracted waves. The vulnerable areas showed a striking resemblance to the area impacted by the tsunami that hit the Indian Ocean in 2004. This research eventually helps to identify and incorporate observational and modeling issues associated with seismic tsunamis and meteotsunami. Key Points: We present the first comprehensive evaluation of meteotsunami in the Indian Ocean using observation and modelingA forced wave to free wave transformation happens on the continental slope, and the bathymetry slope is crucial to near‐shore processesThe meteotsunami exhibits a spectral and spatial similarity to seismic tsunamis that previously occurred in the Indian Ocean [ABSTRACT FROM AUTHOR]

The volcano of Hunga Tonga-Hunga Ha'apai in Tonga erupted on 15 January 2022, generating severe disturbances in the atmosphere and the ionosphere. This event provided us with large amount of data of the atmosphere and the ionosphere, and various kinds of observational studies have been made. Recently several simulation studies have also been made to reproduce and understand the atmosphere–ionosphere variations driven by the volcanic eruption. Although the simulation studies have reproduced the global variations of the atmosphere and the ionosphere successfully, phenomena related with acoustic waves have not been fully investigated. We employed an axisymmetric three-dimensional nonhydrostatic atmospheric model and the whole atmosphere–ionosphere coupled model GAIA. We found that the simulation can produce various kinds of atmospheric waves generated by the eruption, such as acoustic waves, gravity waves, Lamb waves, Pekeris waves, and TIDs concentrically propagating from the eruption site, and atmospheric oscillations with a period of a few minutes. In addition, the results indicate that the eruption generates supersonic shock waves in the volcanic region, leading to the extremely large vertical oscillations in the thermosphere and ionosphere above the volcanic eruption region. [ABSTRACT FROM AUTHOR]

This study conducted experimental and numerical investigations on piezoelectric wafer active sensors (PWASs) bonded to an aluminum plate to assess the impact of bonding degradation on Lamb wave generation. Three surface-bonded PWASs were examined, including one intentionally bonded with a reduced adhesive to create a defective bond. Thermal cyclic aging was applied, monitoring through laser Doppler vibrometry (LDV) and static capacitance measurements. The PWAS with the initially defective bond exhibited the poorest performance over aging cycles, emphasizing the significance of the initial bond condition. As debonding progressed, modifications in electromechanical behavior were observed, leading to a reduction in wave amplitude and distortion of the generated wave field, challenging the validity of existing analytical modeling of wave-tuning curves for perfectly bonded PWASs. Both numerical simulations and experimental observations substantiated this finding. In conclusion, this study highlights the imperative of a high-integrity bond for the proper functioning of a guided wave-based structural health monitoring (SHM) system, emphasizing ongoing challenges in assessing SHM performance. [ABSTRACT FROM AUTHOR]

In this article, an elastic foundation is used to study the characteristics of flexural edge waves propagating on a piezoelectric structure. The nonlocal elasticity theory is introduced to investigate the microscale effect on edge wave propagation. The traditional Kirchhoff plate hypothesis is used to determine the kinematics of the piezoelectric plate. By considering the sinusoidal waveform, a closed-form dispersion relation can be obtained. In the context of a flexural edge wave on a piezoelectric plate, an analytical and graphical comparison between the two boundary conditions (i.e. short circuit and open circuit) is discussed. In the presence of nonlocal elasticity, the dispersion relation is implied as an implicit function of frequency and wave number. A significant difference occurred between the dispersion curves for piezoelectric plates with different foundations and nonlocal parameters. Due to the Pasternak elastic foundation, an increasing rate of the fundamental mode of frequency is observed at the traction-free edge of a thin, semi-infinite piezoelectric plate. In contrast, the nonlocal elasticity tends to decrease this fundamental frequency mode for a particular wave number value. The corresponding phase velocity decreases rapidly within a short range of wave numbers. [ABSTRACT FROM AUTHOR]

High-density polyethylene (HDPE) pipes are becoming increasingly popular, being used in various fields, such as construction, marine, petroleum, water transfer, process water, methane gas collection, oil and gas gathering, gas distribution systems, mining, acid and wet gas lines, offshore oil and gas and in nuclear power plants. Higher-order guided Lamb wave (UGW) modes can be used to detect various defects in complex structures. We will apply this methodology to one of the types of plastic—the structure of high-density polyethylene (HDPE). However, the excitation of UGW modes faces numerous challenges, especially when there is a need to identify which mode is excited. It is essential to note that, in the higher frequency range, multiple different higher-order modes can usually be excited. This can make it difficult to determine which modes have actually been excited. The objective of this research was to successfully excite and receive various higher-order UGW modes in high-density polyethylene structures using both ultrasonic single-element transducers and a phased array. Theoretical calculations were performed using a variety of methods: semi-analytical finite element (SAFE) method, 2D spatial–temporal spectrum analysis and finite element modeling (FEM). The results obtained from both measurements and simulations clearly demonstrate the possibility of efficiently exciting and receiving different Lamb wave modes possessing different phase velocities. [ABSTRACT FROM AUTHOR]

In non-destructive evaluation guided wave inspections, the elastic structure to be inspected is often embedded within other elastic media and the ensuing leaky waves are complex and non-trivial to compute; we consider the canonical example of an elastic waveguide surrounded by other elastic materials that demonstrates the fundamental issues with calculating the leaky waves in such systems. Due to the complex wavenumber solutions required to represent them, leaky waves pose significant challenges to existing numerical methods, with methods that spatially discretise the field to retrieve them suffering from the exponential growth of their amplitude far into the surrounding media. We present a spectral collocation method yielding an accurate and efficient identification of these modes, leaking into elastic half-spaces. We discretise the elastic domains and, depending on the exterior bulk wavespeeds, select appropriate mappings of the discretised domain to complex paths, in which the numerical solution decays and the physics of the problem are preserved. By iterating through all possible radiation cases, the full set of dispersion and attenuation curves are successfully retrieved and validated, where possible, against the commercially available software disperse. As an independent validation, dispersion curves are obtained from finite element simulations of time-dependent waves using Fourier analysis. [ABSTRACT FROM AUTHOR]

Wide band gaps with the propagation of elastic waves at low-frequency are desirable for phononic crystals in many traditional and novel applications. Inspired by the natural helix, we designed a microstructure in a metamaterial plate with an antisymmetric dual helix as the basic local resonant cell. The band structure and displacement transmission curve of metamaterial plates with dual helix cells were calculated by using the finite element method at first, then the band gap characteristics with and without consideration of the mass in the center of the dual helix were compared. The results show that the band gap in the band structure and displacement transmission curves have excellent consistency. Besides, the effects of the parameters including the number of turns of the helix, the plate thickness, and the radius of the attached mass sphere on the band gaps of flexural waves for the metamaterial plate were examined for further evaluation of the potential vibration prohibition application. It is found that the lower frequency of the band gap can be significantly tuned by adding a mass element in the metamaterial plates with dual helix elements, which provides a new method to tune the width of the band gap of a metamaterial plate. [ABSTRACT FROM AUTHOR]

The article is devoted to the analytical and numerical study of the pattern of propagation and attenuation, due to Coulomb friction, of shear waves in an infinite elastic thin plate with a circular orifice of radius r 0 lying on a rough base. Considering the friction forces and their influence on the sample of wave propagation in extended rods or thin plates is important for calculating the stress–strain state in them and the size of the area of motion. An exact analytical solution of a nonlinear boundary value problem for tangential stresses and velocities is obtained in quadratures by the Laplace transform, with respect to time. It turned out that the complete exhaustion of the wave front of a strong rupture occurs at a finite distance r * from the center of the orifice, and an elementary formula is given for this distance (the case of tangential shock stresses suddenly applied to the orifice boundary is considered). For various ratios of the magnitude of the limiting friction force to the amplitude of the applied load, the stopping (trailing) wave fronts are calculated. After passing them, a state of static equilibrium between the elastic and friction forces with a nonlinear distribution of residual stresses is established in the region r 0 ≤ r ≤ r * . For the first time, a precise analytical solution was obtained for the boundary value problem of the propagation of elastic shear waves in an infinite isotropic space with a cylindrical cavity, when a tangential shock load is set on its surface. [ABSTRACT FROM AUTHOR]

Current damage localisation methods often require many sensors and complex signal processing methods. This paper proposes a fusion algorithm based on elliptical localisation and the reconstruction algorithm for probabilistic inspection of damage (RAPID) to locate and image multiple damages. Experimental verification of the damage algorithm was conducted. An ultrasonic probe was used to excite Lamb signals on an aluminium alloy plate, the ultrasonic response signals at different positions within the plate under multiple damages were measured and the constructed algorithm was employed to image the damage location. In the experiment, this method improved localisation efficiency by excluding invalid sensing paths in the sensor network, saving 31.32% of computational time. When some sensors in the sensor network were damaged, this algorithm ensured a positioning accuracy with a positioning error of 5.83 mm. Finally, the algorithm was used to locate multiple damages in the sensor network and the results showed the good robustness of the algorithm. [ABSTRACT FROM AUTHOR]

The interaction between surface waves and a finite rectangular floating plate in a channel is considered analytically, while the location of the plate is not restricted. The mathematical model is based on the linear velocity potential flow theory for the fluid and the Kirchhoff–Love plate theory for the plate. The problem is converted into an integral equation through using the Green function. The second-order singularity associated with a body with no thickness is treated with the Dirac delta function. The developed scheme is used for case studies of various edge constraints. Extensive results are provided for the hydrodynamic forces acting on the plate and the wave reflection and transmission coefficients. The effects of wave frequency, channel width, plate length, and edge conditions are analyzed, and their physical implications are highlighted. Significant findings comprise the highly oscillatory nature of force curves, influenced by the natural frequencies of the channels and the length of the plate, and substantial effects of edge conditions and the plate position on the results. [ABSTRACT FROM AUTHOR]

• We characterized the pressure wave produced by the Tonga volcano using cosmic rays. • We believe this is the first time that a Lamb wave is studied using cosmic rays. • Our high-altitude data provides additional information about this unique event. High-energy cosmic rays that hit the Earth can be used to study large-scale atmospheric perturbations. After a first interaction in the upper parts of the atmosphere, cosmic rays produce a shower of particles that sample it down to the detector level. The HAWC (High-Altitude Water Cherenkov) gamma-ray observatory in Central Mexico at 4,100 m elevation detects air shower particles continuously with 300 water Cherenkov detectors with an active area of 12,500 m2. On January 15th, 2022, HAWC detected the passage of the pressure wave created by the explosion of the Hunga volcano in the Tonga islands, 9,000 km away, as an anomaly in the measured rate of shower particles. The HAWC measurements are used to determine the propagation speed of four pressure wave passages, and correlate the variations of the shower particle rates with the barometric pressure changes. The profile of the shower particle rate and atmospheric pressure variations for the first transit of the pressure wave at HAWC is compared to the pressure measurements at the Tonga island, near the volcanic explosion. By using the cosmic-ray propagation in the atmosphere as a probe for the pressure, it is possible to achieve very high time-resolution measurements. Moreover, the high-altitude data from HAWC allows to observe the shape of the pressure anomaly with less perturbations compared to sea level detectors. Given the particular location and the detection method of HAWC, our high-altitude data provides valuable information that contributes to fully characterize this once-in-a-century phenomenon. [ABSTRACT FROM AUTHOR]

Corrugated plate mist eliminators are commonly employed in industrial processes to eliminate liquid droplets from gas flows. Engineering a mist eliminator with excellent separation performance including high removal efficiency and low pressure drop and is a primary consideration in industrial processes. This study focuses on the separation of tiny droplets reinforced by the generation of transverse vortices with the help of curved wings. The Euler–Lagrange model is developed to predict the behavior of droplets in gas streams, and velocity distributions and particle trajectories on the demisters were derived. And the prediction equations of the curved wing structure sizes on the efficiency and pressure drop of the mist eliminator are established. The results demonstrated that the grade separation efficiency of 10~20 μm droplet was significantly improved by 25.7%~66.51%. Moreover, for the total removal efficiency, it could be improved from.8 to.92 at 5.5 m s−1, and the accompanying resistance factor was as low as 2.7. Among the proposed arrangements, the double‐row single‐column array arrangement was characterized by higher demisting efficiency and lower pressure drop. Overall, compared to other optimization methods, this proposed optimization approach by means of transverse vortices yielded a higher demisting efficiency and less pressure drop. [ABSTRACT FROM AUTHOR]

Recent years have witnessed growing research interest in dual-wavelength mode-locked fiber lasers for their pivotal role in diverse applications and the exploration of nonlinear dynamics. Despite notable progress in their development, achieving reliable mode-locked dual-wavelength operation typically necessitates intricate manual adjustments of the cavity's polarization components. In this article, we present the realization of automatic mode-locking in a dual-wavelength soliton fiber laser. To provide guidance for the algorithm design, we systematically investigated the impact of polarization configurations and initial states on the laser's operation through numerical simulations and linear scan experiments. The results indicate that operational regimes can be finely adjusted around the wave plate position supporting the mode-locked dual-wavelength solution. Furthermore, the laser exhibits multiple stable states at the mode-locked dual-wavelength point, with critical dependence on the initial conditions. Accordingly, we developed a two-stage genetic algorithm that was demonstrated to be effective for realizing automatic dual-wavelength mode-locking. To further improve the performance of the algorithm, a feedforward neural network was trained and integrated into the algorithm, enabling accurate identification of the dual-wavelength states. This study provides valuable insights into understanding how polarization configurations and initial conditions impact the operational regimes of dual-wavelength mode-locked fiber lasers. The algorithm developed can be extended to optimize other systems with multiple stable states supported at the same parameter point. [ABSTRACT FROM AUTHOR]

Localization of fatigue cracks imposes immense significance to ensure the health of the engineering structures and prevent further catastrophic accidents. The nonlinear ultrasonic waves, especially the nonlinear Lamb waves, have been increasingly studied and employed for identifying micro-damages that are usually invisible to traditional linear ultrasonic waves. However, it remains a challenge to locate the fatigue cracks using nonlinear Lamb waves owing to the enormous difficulties in decoding location information from acoustic nonlinearity. Motivated by this, this work presents a data-driven method for precise location of fatigue crack using nonlinear Lamb waves. A 1D-Attention-convolutional neural network is developed to correlate the fatigue crack location with the wavelet coefficients at the second harmonic frequency of Lamb wave signals. The introduction of the Attention layer enables the models to pay more attention to the desired nonlinear features which dominates locating the fatigue crack. In particular, a convenient dataset creation scheme guided by the relative value label is proposed to generate sufficient data commonly required for deep learning approach. In addition, a lightweight single-excite-multiple-receive signal acquisition method is adopted instead of full-matrix capture method used in the traditional research, which highly improves detection efficiency. Numerical simulation and experimental validation manifest that the trained network can be used to establish the complex mapping between the nonlinear ultrasonic signals and the fatigue crack location features, so as to locate barely visible fatigue cracks. Our work provides a promising and practical way to facilitate nonlinear Lamb waves to accurately locate fatigue cracks in large-scale plate-like structures. [ABSTRACT FROM AUTHOR]

Purpose: The examination of the behavior of wave propagation through different kinds of materials under various mathematical models certainly brings out new properties of those materials to the fore. In this contribution, the circular-crested Lamb-type waves in an isotropic homogeneous, elasto-thermal plate with voids sandwich-packed by inviscid liquid layers have been examined in the context of Lord–Shulman and Green–Lindsay generalizations. Methods: Helmholtz's decomposition principle has been used to separate the solenoidal part and the lamellar part of the waves. The normal mode analysis technique has been used to obtain solutions to governing equations. With the help of solutions, the obtained partial differential equations have been converted to ordinary differential equations to find the eigenvalues of the elasto-porothermal plate bordered with inviscid liquid layers. The problem has also been solved from a numerical point of view and the results have been portrayed graphically. Results: The transverse horizontal wave being unaltered due to voids and temperature gradient gets separated from the coupled system corresponding to elastic waves (compressional and transverse vertical), thermal waves, and wave motion due to voids. Apart from that, each layer of liquid possesses one longitudinal wave. The frequency equations have been derived for the flexural and longitudinal wave modes by solving the stiffness matrix. The inviscid fluid and voids decrease the magnitude of phase velocity and attenuation coefficient. Thermal relaxation times have a small impact on wave propagation. Conclusions: The problem of circular-crested Lamb-type waves has been solved mathematically which lays a theoretical foundation for further study of Lamb-type wave propagation in plates. The present work may find applications in many fields such as the petroleum industry, earthquake engineering, soil dynamics, hydrology, as well as biomechanics. [ABSTRACT FROM AUTHOR]

Abstract On 15 January 2022, the largest eruption of the Hunga‐Tonga volcano in recorded history produced a plume registered by multi‐parametric instruments around the world. However, the far‐field hydrogeological responses to Lamb waves from this eruption remain underexplored. We studied the responses of groundwater to the volcanic eruption in the far‐field over 8,700 km, including 274 wells. Results show that the Lamb waves with a speed of 316 m/s affects the groundwater system, leading to similar fluctuations in well water level (WL) and opposite phase fluctuation in borehole strain. Different wells exhibit diverse responses in WL amplitudes, possibly for heterogeneities in local aquifer systems. Gain values of 5 wells that simultaneously measure atmospheric pressure, borehole air pressure, borehole strain and WL are consistent with results obtained through cross‐power spectrum estimation. This work demonstrates a novel response in far‐field groundwater systems induced by Lamb waves and expects application for aquifer parameter estimation.

Ultrasonic guided waves play an essential role in determining the severity of defects in plate-pipe-like structures. One of the parameters that influence the decision to replace a defective structure is the thickness remaining in the structure. Hence, a precise measurement of the remaining thickness is essential in many industries. The objective of this paper is the quantification of defects in small thickness structures. The cut-off property of the guide wave mode is applied to quantify the lowest remnant thickness of defects in small thickness structures. Implementing the cut-off approach in small thickness structures is challenging because of the small wavelength requirements. A linear array transducer, capable of selectively exciting the transducer elements, is used for this application to transmit and receive wave modes. The study focuses on the A1 Lamb wave mode and its cut-off behaviors. The remnant thickness reflects the A1 mode if the frequency of the wave mode is lower than the cut-off frequency of the defect. The reflection of the A1 mode from the defect is analyzed at multiple frequencies utilising the wavelength constrained excitation. The frequency below which the A1 mode appears indicated the remnant thickness of the defect. Furthermore, an advanced excitation approach using the broadband A1 mode identifies the remnant thickness values from a single experiment. In addition, rather than specifying a range of remnant thickness, it precisely quantified its value. This approach was capable of identifying remnant thickness within a maximum error of 2.3% among the set of examples selected. [ABSTRACT FROM AUTHOR]

Carbon fiber-reinforced polymers (CFRPs) are widely used in the fabrication of solid rocket motor casings due to their exceptional performance. However, the bonding interface between CFRP and viscoelastic materials (rubber) is prone to debonding damage during service and storage under complex environmental conditions, which poses a significant threat to the structural integrity and reliability of the engine. Existing nondestructive testing (NDT) methods, such as X-ray imaging, infrared thermography, and ultrasonic testing, although somewhat effective, exhibit significant limitations in detecting interfacial defects in deep or multilayered composite materials, particularly under the challenging conditions of service and storage. This study proposes an innovative method based on active Lamb wave energy analysis and introduces the Damage Evolution Factor (DEF), specifically designed to detect and evaluate interfacial debonding defects in CFRP–rubber bonded structures within solid rocket motors during service and storage. Through numerical simulations and experimental validation, we selected the A0 mode Lamb wave, which is more sensitive to interfacial damage, as the incident wave and excited it on the surface of the structure. Displacement time-history response signals at observation points under different damage models were extracted and analyzed, and DEF values were calculated. The results show that DEF values increase with the size of the interfacial debonding damage. Similar trends were observed in experimental studies, further validating the effectiveness of this method and demonstrating that DEF can be used for the quantitative evaluation of interfacial debonding defects in CFRP–rubber bilayer bonded structures.

Lamb waves propagating in the substrate of linear arrays integrated on a silicon (Si) chip may degrade the elementary performances of the imaging device. In fact, these waves are radiated in the imaging medium. Their superimposition with the relevant ultrasonic signals alters the image performances (i.e., lateral and axial resolutions). In this article, we investigate the interest of using a thin layer of porous silicon (PS) as an absorbing material, aiming to reduce the total device dimensions compared to more traditional backing materials and facilitate device integration with on-chip electronics. The proposed method was applied to Capacitive Micromachined Ultrasonic Transducers. To this purpose, a PS layer with a thickness of 60 μm and a porosity of 50% was etched on the rear side of a 256-elements linear array. The electroacoustic response of the elements integrated on the Si substrate was compared to those on the Si/PS substrate, showing no deterioration of the acoustic characteristics (i.e., center frequency and bandwidth) after PS layer fabrication. To assess the PS silicon layer influence on Lamb wave attenuation, acoustic cross-talks were measured for each array element. The radio-frequency dataset was used to determine the dispersion curves of Lamb waves in the substrate. The comparison between the two substrates showed a significant attenuation value (superior to 30 dB) of Lamb waves induced by the PS layer. [ABSTRACT FROM AUTHOR]

The strongest volcanic eruption since the 19th century occurred on 15 January 2022 at Hunga Tonga‐Hunga Ha'apai, generating unprecedented atmospheric waves not seen before in observations. We used satellite microwave observations from (a) Advanced Technology Microwave Sounder (ATMS) on board the National Oceanic and Atmospheric Administration (NOAA)‐20 and the Suomi‐National Polar‐orbiting Partnership (SNPP) and (b) Advanced Microwave Sounding Unit (AMSU)‐A on board Meteorological operational satellite (MetOp)‐B/MetOp‐C to study these waves in the stratosphere immediately after the eruption. The NOAA Microwave Integrated Retrieval System (MiRS) was applied to these microwave observations to produce atmospheric temperature profiles. The atmospheric Lamb wave and fast‐traveling gravity waves are clearly revealed in both the brightness temperatures and the MiRS retrieved temperatures, revealing their vertical phase structures. This study is the first attempt to perform a detailed analysis of the stratospheric impact of the Tonga eruption on operational satellite microwave observations and the corresponding MiRS retrievals. Plain Language Summary: The strongest volcanic eruption since the 19th century occurred on 15 January 2022 at Hunga Tonga‐Hunga Ha'apai. The microwave instruments onboard the currently operational satellites observed the area in the vicinity of the eruption. The eruption impacts were most obvious at high altitudes (the stratosphere) in the observed microwave brightness temperatures. Additionally, atmospheric temperature profiles have been retrieved using the satellite measured microwave brightness temperatures. The retrieved atmospheric temperature fields also show the impacts of the volcanic eruption in the stratosphere. This study is the first attempt to perform a detailed analysis of the impact of the Tonga volcanic eruption using operational satellite microwave observations and the corresponding retrievals. Key Points: Microwave observations from multiple satellites capture stratospheric waves from the Tonga eruption, including Lamb and gravity wavesMiRS atmospheric temperature retrievals also resolve wave perturbations in the stratosphere after the eruptionThe Lamb wave and the lead gravity wave show no apparent phase change with height, whereas the trailing gravity waves do [ABSTRACT FROM AUTHOR]

Corrosion detection for industrial settings is crucial for safe and efficient operations. Due to its high imaging resolution, the guided–wave full–waveform inversion tomography technique has significant potential for corrosion detection of plate metals. Limited by the long wavelengths of A0 and S0 mode waves, this method exhibits inadequate detection resolution for the earlier shallow and small corrosion defects. Based on the relatively short wavelength characteristics of the SH1 mode wave, we propose a high–precision corrosion detection method via SH1 guided wave using the full waveform inversion algorithms. By conducting finite element simulations of ultrasonic–guided waves on aluminum plates with varying corrosion defects, a comparison was made to assess the detection precision across A0, S0, and SH1 modes. The comparison results showed that, whether for regular or irregular defects, the SH1 mode wave always exhibited higher imaging accuracy than the A0 and S0 mode waves for shallow and small–sized defects. The corresponding experiments were conducted on an aluminum plate with simple or complex defects. The results of the experiments reconfirmed that the full waveform inversion method using SH1 guided wave can effectively reconstruct the shape and size of small and shallow corrosion defects within aluminum plates. [ABSTRACT FROM AUTHOR]

We investigate a two-dimensional transmission model consisting of a wave equation and a Kirchhoff plate equation with dynamical boundary controls under geometric conditions. The two equations are coupled through transmission conditions along a steady interface between the domains in which the wave and plate equations evolve, respectively. Our primary concern is the stability analysis of the system, which has not appeared in the literature. For this aim, using a unique continuation theorem, the strong stability of the system is proved without any geometric condition and in the absence of compactness of the resolvent. Then, we show that our system lacks exponential (uniform) stability. However, we establish a polynomial energy decay estimate of type 1 / t for smooth initial data using the frequency domain approach from semigroup theory, which combines a contradiction argument with the multiplier technique. This method leads to certain geometrical conditions concerning the wave's and the plate's domains. [ABSTRACT FROM AUTHOR]

To study the acoustic characteristics of sound scattered from laminated structures such as elastic plates and shells, it is usually required to solve the Lamb waves' dispersion equations. Many traditional root-finding methods such as bisection, the Newton–Raphson method, and the Muller method are not able to tackle the problem completely. A simple but powerful method named local peaks search (LPS) is proposed to overcome their drawbacks. Firstly, the non-zero part of the dispersion equation is defined as the dispersion function, and its reciprocal is used to transform the zeros (i.e., roots) into local peaks. Secondly, the chosen complex domain is discretized, and the coarse local domains where the local peaks exist are determined by the direct search method globally. Thirdly, the Muller method is applied to obtain the refined locations of local peaks. Lastly, in order to refine the results, a hierarchical scheme is designed and the iteration of the above procedures is implemented; the error is set to be 10−16 as the stop criteria. The accuracy of the LPS method is validated by comparing it with the bisection method for the problem of elastic plates in the vacuum. The acoustic echo structures are analyzed experimentally. By computation of Lamb waves' phase velocity, the critical angles are derived numerically and compared with the results acquired by an experiment using monostatic sound transducers. In this way, it is validated that the elastic scattered wave components are the highlights shown in the time-angle figure. Furthermore, the work can be applied for non-destructive testing, especially underwater structural health monitoring. [ABSTRACT FROM AUTHOR]

Both proper and degenerate Dirac-like cones are observed in dispersion portraits of Lamb waves propagating in traction-free functionally graded (FG) plates with transverse inhomogeneity and obeying the modified Wiechert condition. It is revealed that the Dirac-like cones appear in FG materials with asymmetric profile regardless of the Poisson's ratio, yielding a new approach in the creation of materials possessing Dirac-like cones. The analysis is based on the Cauchy sextic formalism combined with the exponential fundamental matrix method. [ABSTRACT FROM AUTHOR]

Components made of fibre-reinforced polymers (FRP) may suffer from various types of damages, such as cracks or delamination. In order to monitor the structures' material condition, non destructive testing (NDT) methods have emerged – among them, the use of ultrasonic waves. Inter alia, research focused on Lamb waves (LW), which offer promising conditions for NDT processes. However, prior implementation in a specific production environment, practitioners are faced with many open questions such as excitation frequencies to be used or which mode to select for defect identification. Therefore, the study aimed at demonstrating how a finite element analysis (FEA) can assist the experimental design of an LW driven NDT process. For that, a numerical model was developed, capable of computing LW propagations in an exemplary component: Stringer-stiffened C-FRP panels. The study was divided into two parts: In this part, all information regarding the model building is presented and principal functionality demonstrated. In the second part, the FEA is validated and then used to perform parameter studies, highlighting important conditions for practical application. The results of the present paper showed that stiffeners provoke varying interactions with LW modes – effects that increase wave field complexity but do not limit defect identification within or behind the stringer. [ABSTRACT FROM AUTHOR]

Lamb and Rayleigh waves-based dispersion analysis has been carried out for non-destructive surface wave testing of different slab-like structures involving a concrete roof slab, a concrete floor, a concrete pavement, and an asphaltic pavement. An impact was generated by gently striking the slab's free surface with a hammer. A method has also been given to generate the governing (predominant) dispersion mode in the case of Rayleigh wave propagation considering the complex nature of the dispersion function $\vert {{ D}\lpar {c\comma \; \kappa } \rpar } \vert$ | D (c , κ) | ; $c$ c and $\kappa$ κ refer to phase velocity and wavenumber, respectively. The theoretical dispersion plots generated from the inversion analysis by varying the values of different input parameters were subsequently closely matched with the corresponding obtained field dispersion images for different cases in order to back compute the elastic profile of the slab/pavement. For developing the dispersion images, the Park's wavefield transformation method was employed. For checking the thicknesses of the different layers, cylindrical cores were also extracted. The study is expected to be useful for evaluating different slab-like structures, including pavements, by using surface wave-based non-destructive tests. [ABSTRACT FROM AUTHOR]