Search

Combinatorial analysis of Ag–Pd alloy thin films shows the formation of a solid solution with the face‐centered cubic structure for all investigated alloy compositions. Using mixed matter theory and the high field model, oxide growth upon applying an anodic potential is indicated. Electrochemical impedance spectroscopy supports the idea of oxide formation based on a change in behavior correlated to a sharp increase in oxide formation as indicated by cyclic voltammetry measurements. After polarization at 4 V, a stable total impedance and increasingly less‐pronounced phase shift are detected in the frequency range of 100 mHz to 10 kHz, which encompasses the common range of application of active implantable medical devices (AIMD). Upon fitting the measured impedance data with the Randles circuit, capacitances are determined in the nF cm−2 range for the investigated alloys and attributed to the formed mixed oxide layer. Charge transfer resistances are found to be in the kΩ cm−2 range. No correlation between alloy composition and capacitance or resistance can be detected so far. These findings indicate a fundamental applicability of Ag–Pd alloys for use in AIMD. [ABSTRACT FROM AUTHOR]

The electrocatalytic activity of electrode materials synthesized by anodic selective dissolution of Ag–Pd alloys based on silver (4 and 8 at % Pd) was studied. Kinetic regularities of formic acid electrooxidation on palladium and anodically modified Ag–Pd alloys in an acidic sulfate solution have been established. The process includes the diffusion of HCOOH, its dissociative chemisorption, and irreversible ionization of atomic hydrogen. The conditions for formic acid anodic oxidation on Pd and Ag–Pd alloys were determined depending on the composition of the electrode system and the mode of preliminary electrochemical modification (selective dissolution) of the alloy using transient electrochemical measurements. The role of the surface development of an alloy in the kinetics of anodic degradation of formic acid was revealed. It was shown that the selective dissolution of Ag–Pd alloys contributes to a noticeable increase in the rate of the kinetic stage of atomic hydrogen ionization. A necessary condition for the activation of the anodically modified alloy in relation to the electrooxidation of HCOOH is the excess of both critical parameters (charge and potential) corresponding to the onset of morphological development and phase transformations in the surface layer of the Ag–Pd systems. [ABSTRACT FROM AUTHOR]

The reactions between palladium (Pd), palladium-silver alloy (Pd-Ag) and silicon carbide (SiC) from 1200 °C to 1400 °C have been studied to investigate the impact of liquid phases on reaction products formation. The liquid phases were generated in Pd/SiC reactions at 1400 °C and in Pd-Ag/SiC reactions above 1300 °C. An increase in the amount of liquid associated with higher temperatures or Ag presence strongly affected the reaction mechanism and was responsible for the inhomogeneous dissolution of SiC grains and grain boundaries by Pd-rich phase at reaction front. This study helps understand Pd's role on Ag release through SiC layer in Tri-structural isotropic (TRISO) fuel particles. [ABSTRACT FROM AUTHOR]

Selected results of investigations focused on the changes to some mechanical properties of palladium and several palladium-based alloys caused by exposure to hydrogen have been collected and presented. The findings indicate that the mechanical properties of pure palladium are highly susceptible to alteration upon exposure to hydrogen. In the cases of alloying palladium with silver and copper, the alloys, as compared to palladium, appear to resist changes to mechanical properties. In the case of alloying palladium with manganese, the interesting order–disorder phenomenon plays an important role on the effects of hydrogen exposure on their mechanical properties. [ABSTRACT FROM AUTHOR]

Copyright of Chinese Journal of Inorganic Analytical Chemistry / Zhongguo Wuji Fenxi Huaxue is the property of Beijing Research Institute of Mining & Metallurgy Technology Group and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The field of electrochemical CO2 reduction has been transitioning to industrially relevant scales by changing the architecture of the electrochemical cells and moving away from the traditional aqueous H‐cells to membrane electrode assemblies (MEA). The reaction environments in MEAs vary drastically from that of aqueous H‐cells, which could result in significantly different catalytic activity. In this paper, we test AgPd alloys, one of the most promising CO producing catalysts reported, at industrially relevant scales (50 to 200 mA/cm2) in a MEA configuration. We report that, with increasing Pd composition in the electrode, the CO selectivity reduces from 99 % for pure Ag to 73 % for pure Pd at 50 mA/cm2. The MEA configuration helps attain a high CO partial current density of 123 mA/cm2. We find that catalytic activity reported in aqueous H‐Cells does not translate at higher current densities and that cell architecture must play an important role in benchmarking catalytic activity. [ABSTRACT FROM AUTHOR]

Silver (Ag), palladium (Pd), and bimetallic silver-palladium (Ag-Pd) coatings were deposited on a mild steel surface by the co-sputtering method. The aim was to investigate and compare the corrosion behavior of Ag-Pd nano-coatings as well as the effect of increasing the weight ratio of Ag in the Ag-Pd alloy in the 3.5% NaCl solution. The corrosion protection performance and barrier protection properties were monitored using electrochemical impedance spectroscopy and potentiodynamic polarization. The surface of the coatings was characterized by scanning electron microscopy, atomic force microscopy, energy-dispersive x-ray spectroscopy, and field-emission scanning electron microscopy. The results of corrosion measurements revealed a relationship between silver wt.% and corrosion resistance. Also, all the coatings had protective effects and barrier properties on the mild steel in the corrosive solution. The best efficiency was observed in silver monometallic coating with 54 nm thickness. [ABSTRACT FROM AUTHOR]

Hydrogen, deuterium, and helium gases were separately cycled through a Johnson-Matthey purifier containing coiled palladium silver alloy tubing: Pd25Ag (75 wt% Pd and 25 wt% Ag). During the cycling of D 2 gas, evidence of anomalous heat production was observed. However, during the cycling of H 2 and He, very little (H 2) or no (He) unusual heat events were observed. After cycling the D 2 gas through the coiled tubing for several months, Pd25Ag samples showed an increase in Cu and Fe compared with the amounts in unexposed Pd25Ag. Chromium, manganese, and zinc were detected in gas-cycled Pd25Ag samples, whereas they were not detected in unexposed Pd25Ag samples. In particular, Zn was present in the gas-cycled Pd25Ag material in larger quantities than either Cr or Mn. Although a small amount of Cu was present in the Pd25Ag coil before the D 2 gas cycling, 7 times more was present after the cycling. Multiple material characterization techniques were used to obtain both pre-test and post-test elemental composition. The results indicate that novel post-test elements, primarily on the surface, were created by unknown nuclear mechanisms at low energy. • Surface transmutations occurred in deuterium gas cycling experiments of PdAg tubes. • Zn and Cr not present in PdAg before experiments were observed on PdAg afterwards. [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • Ag@Pd core-shell structure catalyst can be synthesized by galvanic replacement. • Electron shift in Ag@Pd structure increases local electron density around Pd atom. • Ag@Pd structure can promote phase transformation from Pd0 to PdO state. • Ag@Pd/TiO 2 exhibits higher methanol oxidation activity with a lower Pd loading. Abstract We show that silver palladium bimetallic core-shell structure catalysts supported on TiO 2 substrate (Ag@Pd/TiO 2) are highly active with a low palladium loading for toluene purification in oxidation reaction. The Ag@Pd catalysts were synthesized by galvanic replacement of Pd coating on Ag nanoparticles. Transmission electron microscopy (TEM), high-resolution TEM, and scanning TEM with energy dispersive spectrometer confirmed that the catalysts have a core-shell configuration, and are spherical in shape with an average diameter size of about 9.0 nm. The UV–vis absorption spectroscopy and selected area electron diffraction further proved that the intimate contact and different electronegativity of Ag and Pd in core-shell structure result in electrons transferring from Ag core to Pd shell, which increases local electron density around Pd atom. In addition, X-ray photoelectron spectroscopy reveals that such an increase of electron density on Pd active site in Ag@Pd/TiO 2 catalyst can substantially strengthen the chemisorption with reactant of O 2 , further promote the phase transformation from Pd0 metal to PdO oxidation state, and finally maintain the normal operation of Pd0-PdO synergic mechanism during toluene oxidation reaction. Hence, compared to monometallic Pd/TiO 2 catalyst, the as-prepared bimetallic core-shell Ag@Pd/TiO 2 catalyst exhibits greatly higher toluene oxidation activity as a whole although its palladium loading value is just one third of Pd/TiO 2. The high catalytic oxidation activity with a low Pd loading makes the Ag@Pd/TiO 2 a promising catalyst for use in VOCs purification. [ABSTRACT FROM AUTHOR]

• Systematic study of superpermeation in Pd, PdCu, and PdAg foils. • Argon sputter clean enable high and stable superpermeation. • Flux through PdCu 5X greater than Pd∼PdAg, reflecting faster desorption kinetics. • Flux >10−2 mol H m−2 s−1 achieved. • 100% superpermeation of supplied H 2 achieved. Superpermeation of hydrogen isotopes through metal foils is a critical component for efficient fuel recycling in fusion power systems. In that context hydrogen permeation through foils of palladium and its alloys with silver and copper was studied at low temperature (60 - 200°C) under plasma exposure. These alloys differ significantly in both bulk and surface properties, and comparisons can provide mechanistic insights. Permeation was observed only during plasma operation, confirming the negligible contribution of molecular hydrogen to the observed flux. As-received foils required surface treatment to achieve top performance. For Pd and Pd75Ag25 an oxidation treatment increased permeation an order of magnitude, but proved unstable as this desirable surface was reduced under hydrogen plasma exposure. In contrast, an Ar plasma cleaning step provided both high and stable flux. As-received FCC phase Pd60Cu40 foils required annealing to transform it into the high permeability BCC phase that delivered top performance. All foils displayed similar temperature dependence with flux declining with temperature, suggesting that the primary rate-limiting step is absorption of superthermal hydrogen. Among these foils the hydrogen flux through PdCu was 3 - 5X greater than that of Pd or PdAg, which were similar. The superiority of BCC PdCu is attributed to its superior hydrogen desorption kinetics. Using PdCu 100% permeation of supplied hydrogen was achieved, and the flux saturated with increasing plasma power at values >10−2 mol H·m−2·s−1, and under these conditions permeation rates are equivalent with or without the membrane present. The fluxes achieved are the highest reported to date at these conditions, and the results highlight the important roles of both surface and bulk properties. [Display omitted] [ABSTRACT FROM AUTHOR]

We introduce the class of discrete silver(I)-palladium(II)-oxo nanoclusters with the preparation of {Ag4Pd13} and {Ag5Pd15}. Both polyanions represent the first examples of noble metal-capped polyoxo-noble-metalates in a fully inorganic assembly, featuring an unprecedented host-guest mode containing hetero- and homometallic Ag-Pd and Ag-Ag bonding interactions. Comprehensive theoretical calculations suggest that the Ag-Pd metallic bonds originate partially from surface confinement of AgI guest ions onto the anionic polyoxopalladate host that is induced by strong electrostatic forces. This work opens the field of fully inorganic silver-palladium-oxo nanoclusters, which can be considered as discrete mixed noble metal precursors for the formation of monodisperse core-shell nanoparticles, with high relevance for catalysis. [ABSTRACT FROM AUTHOR]

Silver-palladium alloy wire has been shown as an economical and reliable substitute for gold wire in various applications in the electronic packaging industry. The success of wire bonding relies on the formation of an interfacial intermetallic compound (IMC). This study is aimed to investigate the formation behavior of IMCs between an Al pad and Ag-Pd alloy wire with various Pd concentrations of 1.0-6.0% for the as-bonded commercial Ag/Al joint. The interfacial IMCs were investigated with scanning electron microscopy and energy-dispersive x-ray spectroscopy. The IMCs formed are separate (Ag, Pd)Al and (Ag, Pd)Al for a Ag6Pd wire bond, while (Ag, Pd)Al and (Ag, Pd)Al are mixed for the other Ag(1-4.5)Pd alloy wire bonds. The thickness of the total IMC layer varies from 0.65 μm for Ag1Pd to 0.91 μm for Ag6Pd, yet a minimum of 0.44 μm exists for Ag3.5Pd. The compound formation behavior was found to correspond with the Ag-Al phase diagram. After pressure cooker tests, a less stable IMC (Ag, Pd)Al formed at the AgxPd/Al interface. [ABSTRACT FROM AUTHOR]

Highly dispersed bimetallic AgPd nanoparticles with different composition have been successfully deposited on the metal-organic frameworks (ZIF-8) by using a simple liquid impregnation method. The resultant catalysts are composition dependent toward dehydrogenation of formic acid, while Ag 18 Pd 82 @ZIF-8 exhibits exceedingly high catalytic activity, with the turnover frequency (TOF) value of 580 h −1 , and 100% hydrogen selectivity at 80 °C. [ABSTRACT FROM AUTHOR]

Palladium–silver (PdAg) alloy nanospheres with unique structure were prepared using a one-pot procedure based on the galvanic replacement reaction. Their electrocatalytic activity for ethanol oxidation in alkaline media was evaluated. The morphology and crystal structure of the samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). Electrochemical characterization techniques, including cyclic voltammetry (CV) and chronoamperometry (CA) measurements were used to analyze the electrochemical performance of the PdAg alloy nanospheres. The SEM and TEM images showed that the PdAg alloy nanospheres exhibit a hierarchical nanostructure with hollow interiors and porous walls. Compared to the commercial Pd/C catalyst, the as-prepared PdAg alloy nanospheres exhibit superior electrocatalytic activity and stability towards ethanol electro-oxidation in alkaline media, showing its potential as a new non-Pt electro-catalyst for direct alcohol fuel cells (DAFCs). [ABSTRACT FROM AUTHOR]

An efficient process for the recovery of palladium from waste printed circuits boards (PCBs) is detailed. Palladium is employed as an electrode material in multi-layer ceramic capacitors (MLCCs). These components can be easily removed from PCBs by de-soldering. As palladium is alloyed with silver, its dissolution is readily achieved using dilute nitric acid. As a result, a solution containing palladium along with base metals, mostly copper and iron, is obtained. This solution is then processed through solvent extraction (SX) with a solvent based on N , N ′-dimethyl, N , N ′-dibutyltetradecylmalonamide (BDMA), a robust extracting molecule previously developed in the frame of the reprocessing of waste nuclear fuel. The volume of effluents generated during the SX sequence is limited: iron scrubbing is operated with a very low aqueous to organic phase volume ratio, no specific metal chelator is required for palladium stripping, and no shift from acidic to basic media is required. Finally, a ca 1 g/L Pd(II) aqueous solution with 99,4% purity is obtained, from which palladium is directly isolated as dichlorodiammine palladium(II) salt (Pd(NH 3) 2 Cl 2) after precipitation with ammonia. Overall, palladium is quantitatively recovered from the leaching solution, and no palladium was detected in the remaining solid residue. Purity is high, as no contaminating metal could be detected in the final palladium salt. The proposed approach is simple and complementary to existing hydrometallurgical processes dedicated to gold and copper recovery. • A palladium recovery process from waste PCBs was developed at laboratory scale. • This hydrometallurgical process is a block complementary to existing processes. • Palladium containing components are separated from the board by de-soldering. • Leaching with 3 M nitric acid and solvent extraction enable pure palladium isolation. • Effluents are well controlled during palladium purification with solvent extraction. [ABSTRACT FROM AUTHOR]