Search

6.Databaseofloaddata Miyata and Bathurst (2019) developed a database of 113 measured steel grid loads (T max) from 11 instrumented steel grid walls constructed with cohesive-frictional soils and purely frictional soils. Reliability-based design and analysis for internal limit states of steel grid-reinforced mechanically stabilized earth walls. Thegeneralapproachdescribedin thispaperisanimportantcontributiontonext-generationanalysis and design using modern concepts of RBD for internal stability design of both steel and polymeric soil-reinforced MSE walls and is thus in alignment with the international movement towards RBD for geotechnical structures (e.g., Low and Phoon 2015;Phoon2017;PhoonandChing2015;ISSMGE2017). Allen et al. (2001, 2004) quantified the level of accuracy of the Simplified Method for steel MSE walls using bias statistics deduced from a large number of instrumented walls. 1.Introduction This paper is focused on reliability-based design (RBD) and analysis for tensile strength and pullout limit states of steel grid-reinforced mechanically stabilized earth (MSE) walls constructed with frictional soils and subjected to typical operational conditions. [Extracted from the article]

Copyright of Canadian Geotechnical Journal is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The Simplified Method as reported in AASHTO and Federal Highway Administration (FHWA) manuals has been demonstrated to give poor predictions of unfactored reinforcement loads and strains, especially for geosynthetic reinforced soil walls. The writers have proposed the K-stiffness Method to improve the load prediction accuracy for walls under working stress (operational) conditions. However, it has also been recognized in recent publications by the writers and others that further improvements to the K-stiffness Method are needed. Furthermore, acceptance of the K-stiffness Method has been hindered due to its perceived complexity and the use of the plane strain friction angle to quantify the strength of the reinforced soil. This paper takes a fresh look at both methods and uses lessons learned from the K-stiffness Method development to improve the accuracy of the AASHTO/FHWA Simplified Method. Key parameters introduced during the development of the K-stiffness Method are applied to the Simplified Method and updated to further improve load prediction accuracy. Additional wall case histories have been added to the database used for the original K-stiffness Method to calibrate the new model and to broaden its utility. An important improvement is a single model that allows for seamless load prediction across a range of walls constructed with relatively extensible geosynthetic reinforcement and inextensible steel reinforcement materials. The quantitative improvement of the new model (Simplified Stiffness Method) compared to the current AASHTO/FHWA Simplified Method is demonstrated through statistical analysis of load bias values (i.e., the ratio of measured to predicted reinforcement load). [ABSTRACT FROM AUTHOR]

The paper reports the details of numerical models used to predict the performance of two 3.6 m-high well-instrumented wrapped-face walls. The walls were nominally identical except that the reinforcement material in one wall was a steel welded wire mesh and in the other a biaxial polypropylene geogrid. The backfill soil was modelled using both linear and nonlinear elastic-plastic constitutive models. A general hyperbolic (nonlinear) axial load-strain-time model was used for the reinforcement. The numerical results show good agreement with measured performance features for the welded wire mesh wrapped-face wall. Agreement between numerical predictions of facing displacements and maximum reinforcement loads was less accurate for the very flexible geogrid wrapped-face wall. The discrepancies are believed to be related to the unusually flexible wrapped face used in the geogrid wall construction. Numerically predicted and measured maximum reinforcement loads are compared to loads using the AASHTO reinforcement strength-based design approach (Simplified Method) and the Simplified Stiffness Method which is an empirical reinforcement stiffness-based method. The paper provides physical test data that can be used to benchmark other numerical models, highlights lessons learned during the development of the models, and identifies reasonable expectations for numerical model accuracy for models of similar complexity used to simulate the performance of mechanically stabilized earth (MSE) wall structures under operational conditions. [ABSTRACT FROM AUTHOR]