Search

• An attempt to characterize thin, low impedance paper at various high strain-rates. • The creation of a digital twin of the physical Split Hopkinson Test bench. • To demonstrate that there can be distortions of the transmitted measuring signal. This work deals with the high strain-rate characterization of paper under uniaxial tension using a Split Hopkinson test bench. An aluminum bar system featuring a highly sensitive hollow transmission bar was used. Paper tests were performed in a strain-rate range between approximately 60 s−1 and 210 s−1. The experimental tests showed that the breaking strength appears to decrease with increasing strain-rate. To verify these results, a digital twin of both the paper specimen and the entire test rig was created in an explicit Finite Element method environment. The numerical model was then used to perform a parameter study with different types of transmission bars. It was shown that the system is quite sensitive to additional masses caused by the specimen fixtures, as well as to drastic reductions in the cross section of the transmission bar. As a result, the transmitted measuring signal can be distorted and may need to be corrected using the digital twin. [ABSTRACT FROM AUTHOR]

A computationally efficient method to study the in-plane and out-of-plane dimensional instability of thin paper sheets under the influence of moisture changes is presented. The method explicitly resolves the bonded and the free segments of fibers in the sheet, capturing the effect of anisotropic hygroexpansion at the fiber level. The method is verified against a volumetric model. The importance of longitudinal fiber hygroexpansion is demonstrated in spite of the absolute value of longitudinal hygroexpansion being an order of magnitude lower than the transverse hygroexpansion component. Finally, the method is used to demonstrate the formation of macroscopic sheet curl due to a moisture gradient in structurally uniform sheets in the absence of viscoelastic or plastic constitutive behavior and through-thickness residual stress profiles. [ABSTRACT FROM AUTHOR]

A fully printed piezoelectric based touch sensor device has been successfully fabricated on flexible polyethylene terephthalate (PET) and paper substrates using screen printing technique. The device, consisting of a 4 × 4 array of printed sensors and interconnect lines, was fabricated using silver (Ag) ink. Screen printed polyvinylidene fluoride (PVDF), as a piezoelectric layer, was sandwiched between the printed Ag top and bottom electrode metallization layers. A linear relationship between the sensor response and varying applied forces to the device was obtained through finite element analysis (FEA) method simulation. X-ray diffraction (XRD) analysis was performed to verify the formation of the β-phase crystals in the PVDF layer during the curing process. The effective polarization of the printed piezoelectric layer was analyzed using capacitance-voltage analysis. A sensitivity of 1.2 V/N and 0.3 V/N, with correlation coefficient of 0.9954 and 0.9859, was obtained for the PET and paper based printed touch sensors, respectively. The piezoelectric-voltage analysis demonstrated that the printed sensors can be used for both touch and force based applications. [ABSTRACT FROM AUTHOR]

The present paper explores the short span compression tester (SCT) as a means to experimentally determine the transverse shear moduli of paper. These moduli, which are known to be difficult to determine by any other means, are of importance for the behavior of paper during tissue manufacturing and in the converting and embossing of paperboard. Testing was conducted on paper of two different grammages both in MD and in CD. By applying the Timoshenko–Engesser theory for buckling of shear compliant materials, estimates of the transverse shear moduli were obtained through the measured SCT values and standard measurements of the Young’s modulus and the thickness. These estimates were evaluated by detailed FE-analyses of the SCT setup incorporating initial geometrical imperfections representative for real test conditions. It was found that the Timoshenko–Engesser theory gives estimates of the transverse shear moduli that are within an accuracy well applicable for most engineering purposes. The results suggest that the method is at least as accurate as any other, more involved, method that could be used for the purpose. [ABSTRACT FROM AUTHOR]

The mechanical response of three different structural core sandwich panels in out-of-plane compression and shear has been analyzed. Specific core shapes examined are arc-tangent, wavy trapezoidal and hemispherical. Unit cells consisting of representative elements of the core attached to face sheets were selected for analysis. Both face sheets and core were assumed made from paper. Finite element analysis employing large deformation and rotations and orthotropic elastic–plastic behavior was used. The results show that the arc-tangent and trapezoidal cores are prone to collapse by extensive bending and buckling, whereas the hemispherical core behaved more stably in compression and shear. Core sheets with a hemispherical shape were prepared from copy paper sheets in a specially designed forming machine. Sandwich test specimens were prepared from this core and tested in out-of-plane compression, and the load-displacement response was compared to predictions from finite element simulations. The experimental and finite element results were consistent. [ABSTRACT FROM AUTHOR]

The tensile response of dense fiber-based materials like paper or paperboard is mainly dependent of the properties of the fibers, which store most of the elastic energy. In this paper, we investigate the influence of geometrical and material parameters on the mechanical response of the pulp fibers used in paper manufacturing. We developed a three-dimensional finite element model of the fiber, which accounts for microfibril orientation of cellulose fibril, and the presence of lignin in the secondary cell wall. The results showed that the change in the microfibril orientation upon axial straining is mainly a geometrical effect, and is independent of the material properties of the fiber, as long as the deformations are elastic. Plastic strain accelerates the change in microfibril orientation and thus makes it material-dependent. The results also showed that the elastic modulus of the fiber has a non-linear dependency on microfibril angle, with elastic modulus being more sensitive to the change of microfibril angle around small initial values of microfibril angles. Based on numerical results acquired from a 3D fiber model supported by available experimental evidence, we propose an anisotropic-kinematic hardening plasticity model for a fiber within a beam framework. The proposed fiber model is capable of reproducing the main features of the cyclic tensile response of a pulp fiber, such as stiffening due to changing microfibril angle. The constitutive model of the fiber was implemented in a finite-element model of the fiber network. By using the fiber network model, we estimated the level of strain that fiber segments accumulate before the typical failure strain of the entire network is reached. [ABSTRACT FROM AUTHOR]

The iso-margin method based on the classical analytical equations is widely used in the development of extra high voltage (EHV) bushing. Therefore, its effectiveness and feasibility have been fully validated. However, with the theoretical formula, it is difficult to evaluate the influence of stray capacitance and temperature on the internal electric stress of the ultra high voltage (UHV) bushing. It?s necessary to further improve the traditional iso-margin method. Firstly, the basic principle of iso-margin method has been briefly described. After that, the E-field distribution of condenser bushing was investigated on the Finite Element Method (FEM) computing platform. Then, the mathematical model of the advanced equal margin design method was established. Furthermore, this paper presents the program flow of optimization which combines the simulation of electro-thermal coupling process and the particle swarm optimization (PSO) algorithm. The proposed methodology was applied to the design of the prototype of the UHV resin impregnated paper (RIP) oil-SF6 bushing, which realizes the uniform axial E-field distribution of the bushing condenser. Meanwhile, the partial discharge margin between adjacent foils can be equal. Moreover, the hot-spot temperature is lower than the operation limiting temperature of the RIP material. The bushing condenser was fabricated according to the optimal structure design. The prototype of bushing has passed through all the type tests. In this paper, the FEM electro-thermal coupling simulation and the advanced equal margin design method were applied to the inner insulation structure optimization of the UHV RIP oil-SF6 bushing. Meanwhile, the proposed methodology provides some theoretical guidelines for the future research and development of other types of bushing on the UHV level. [ABSTRACT FROM AUTHOR]