Search

This paper reports the effect of process orientation on the mechanical behavior and piezoelectricity of electroactive paper (EAPap) made from natural cotton pulp. EAPap is fabricated by a casting and wet drawing of cellulose film after dissolving cotton with LiCl and DMAc solvent. During the fabrication, permanent wrinkles, a possible factor for performance deterioration, were found in the films. Finite element method was introduced to identify the formation mechanism behind the wrinkles. The simulation results show that the wrinkles were caused by buckling and are inevitable under any conditions. The tensile and piezoelectric tests show that the orientation dependency of the stretched EAPap gives the anisotropic characteristics on both mechanical and piezoelectric properties. In this research, the anisotropic elastic moduli and Poisson’s ratios are reported. The piezoelectric charge constant of EAPap in the linear elastic is calculated. The piezoelectric charge constants of EAPap are associated with the alignment angle in the order of 45° > 0° > 90° due to the strong shear effect. The higher stretching ratio gives the higher piezoelectricity due to the alignment of the molecular chains and the microstructure in EAPap. The highest piezoelectric charge constant is found to be 12 pC/N at a stretching ratio of 1.6 and aligning angle of 45°.

Paper has always been of great importance as a printing and packaging material. Due to its potential for recyclability and reusability, which result in a low environmental impact, it is expected that this importance will soar over the coming years. Nevertheless, even though paper has been in use for decades, many research questions are still open, especially in the field of mechanics. One of these questions is the appropriate size of a representative volume element (RVE) of the microstructure of paper. Therefore, a finite element network model of interconnected fibers was developed which represents the microstructure of paper. In order to create the network model realistically, geometry and material quantities were taken from experimental investigations. Additionally, single fibers and fiber bonds were investigated beforehand in order to incorporate their proper behavior into the network. Based on this, the networks were generated and subsequently loaded by applying mixed displacement and traction boundary conditions. The resulting effective stresses were compared to determine the necessary RVE size. Two approaches were considered for modeling the RVE: (i) one single "large" network, and (ii) a certain number of smaller networks whose average yielded a statistically representative effective response. As a result, the second approach turned out to be less computationally intensive due to smaller models and the possibility to run calculations simultaneously. Concluding, it was possible to determine the size of the RVE which will be used to investigate various individual microstructural effects on the macrostructure in the future. [ABSTRACT FROM AUTHOR]

In this contribution, the causes leading to the undesired unevenness on the exterior surface of a paper‐based sandwich structure during the manufacturing process are investigated. This provides insight into the manufacturing parameters that need to be adjusted to reduce this waviness. A finite element model of the pressing process is developed in the commercial software ABAQUS and then used to analyze the formation of the surface unevenness. The sandwich structure adopted in the model consists of a decorative layer, an intermediate layer, a corrugated core and a bottom layer. In particular, the core has a sinusoidal structure with various geometry parameters, which are adjusted in the model to investigate the effect on the waviness of the top surface. The results of the quasi‐static process simulation correlate well with the experimental results. A subsequent parameter study based on the design of experiments (DoE) shows the relationship between the material parameters of the intermediate/bottom layer and the resulting waviness. [ABSTRACT FROM AUTHOR]

Air filters are placed upstream of internal combustion engines to remove dust particles in the suction air. In this article, we examine the acoustic characterization of an air-filtering unit in the absence of mean flow. For this purpose, a circular air-filtering unit with an axial inlet and side outlet widely used in the automobile industry is considered. The air-filter element is modeled as an equivalent acoustic fluid with finite flow resistivity. The flow resistivity of the region is estimated from the permeability of the filter paper and the geometrical arrangement of the paper folds (pleats) inside the air-filter element using an electrical analogy. A numerical model based on the finite element method (FEM) and an analytical model using classical one-dimensional plane wave analysis (1-D PWA) was developed. Experiments were carried out using an impedance tube to estimate transmission loss. A good correlation is observed between the FEM model and the experiments. The results obtained from the 1-D PWA are in reasonable agreement with those obtained from the other two methods. [ABSTRACT FROM AUTHOR]

To explore the application of cold-formed thin-walled steel-paper straw board(CTSPSB) composite wall in practical engineering and further meet people's living requirements, it was proposed to open holes in the composite wall to simulate the doors and windows in practical applications. Two composite wall specimens were tested to study the shear performance of the CTSPSB composite wall. Through the analysis of specimens' damage forms and experimental data, the characteristic values of bearing capacity and lateral stiffness were obtained. And then, the model of the composite wall was built by ANSYS, and finite element analysis (FEA) results were consistent with the experimental results, which could verify the feasibility of the finite element model. Moreover, the model needed to open holes and extensive parameter analysis was carried out. The FEA results indicate the most reasonable distance between screws around the opening is 150 mm; the most suitable spacing between the small studs is 400 mm; the position of the opening has the least influence on the shear performance, and the difference between the results of the five groups of models is within 5%; while the width of the opening has the greatest impact on the shear performance. Compared with the wall without opening, the bearing capacity of the wall with an opening width of 600 mm, 1200 mm and 1800 mm decreases by 38%, 46% and 52% respectively. Besides, the calculation formula of shear capacity of CTSPSB composite wall with openings was improved, which could be used as experience for practical engineering. [ABSTRACT FROM AUTHOR]

Embossing is a functional and strategic process for creating high-quality multi-sensory tissue-paper products. Embossing modifies the sheet surface by generating hill and/or valley designs, changing the third-dimension z with a compressive die. This research work specifically concerns the impact study of the engraving finishing geometry on the final properties of tissue paper. This work led us to conclude that, even though the sheets individually present a higher hand-feel (HF) value for the straight finishing geometry, the highest softness was obtained in the two-ply prototype for the round finishing geometry. Moreover, this study confirmed that the HF value reduces with the increase of the bulk, being more accentuated for the micropattern. Relevant differences could not be seen in the spreading kinetics of the liquid droplets over time. Thus, the finishing geometry of the 3D plates did not impact the absorption kinetics on these samples. The finite element model allows us to understand the effect of the plate pattern and its finishing geometry on the paper, and the simulation results were in accordance with the experimental results, showing the same trend where patterns with a round finishing geometry marked the tissue-paper sheet more than patterns with a straight finishing did. [ABSTRACT FROM AUTHOR]

Embossing is a converting process in which the surface of a tissue paper sheet is changed under high pressure, allowing different functions. In this work, the authors intend to study how the embossing pressure affects the main properties of tissue paper, using a laboratory embossing system. An optimum pressure was achieved at 2.8 bar to this embossing laboratory set-up. The effect of pressure when densifying the paper sheet gives it a gain in mechanical strength but no differences in terms of liquid absorbency. The two embossing patterns present different behaviors but both evidence losses in mechanical and softness properties. On the other hand, the finite element method (FEM) does not show clear evidence of how the pressure affects the paper strength. For the deco die, it is possible to observe that the amount of yielding is slightly higher for lower pressure (2.4 bar), but this plasticity state parameter is very similar for 2.8 bar and 3.2 bar. For the micro die, FEM simulations of the manufacturing pressure do not show a considerable impact on the amount of plasticity state of the material; only for 3.2 bar, it shows a change in the pattern of the plasticity state of the paper during the embossing processes. In the end, to achieve a final product with excellent quality, it is important to make a compromise between the various properties. [ABSTRACT FROM AUTHOR]

A square spiral incision was introduced into a 15 × 15 cm regular quadrilateral conductive film to study the modulation of electrothermal distribution by kirigami structure. Based on the simulation of finite element method, the transition from thermal focusing to thermal defocusing could be achieved by increasing the length of connection between adjacent modules. The effective electrothermal area can be increased by nearly two times through increasing the length increment of the notch length between adjacent modules. The maximum temperature was decreased from 254 °C to 44 °C, and the temperature difference was adjusted from 76 °C to 4 °C by increasing the number of kirigami module. Through the contact temperature measurement experiment on graphite paper kirigami structure, the trends could be verified. By creating an equivalent circuit model and considering the influence of heat conduction, the peak temperature at the center of the structure and the decrease of the overall temperature could be explained. By deriving the relationship between the temperature of conductive film of kirigami structure with time and position, the electrothermal characteristics of previously reported graphene kirigami structure could be predicted. [ABSTRACT FROM AUTHOR]

Transport of volatile organic compounds (VOCs) through porous media with active surfaces takes place in many important applications, such as in cellulose-based materials for packaging. Generally, it is a complex process that combines diffusion with sorption at any time. To date, the data needed to use and validate the mathematical models proposed in literature to describe the mentioned processes are scarce and have not been systematically compiled. As an extension of the model of Ramarao et al. (Dry Technol 21(10):2007–2056, 2003) for the water vapor transport through paper, we propose to describe the transport of VOCs by a nonlinear Fisher–Kolmogorov–Petrovsky–Piskunov equation coupled to a partial differential equation (PDE) for the sorption process. The proposed PDE system contains specific material parameters such as diffusion coefficients and adsorption rates as multiplication factors. Although these parameters are essential for solving the PDEs at a given time scale, not all of the required parameters can be directly deduced from experiments, particularly diffusion coefficients and sorption constants. Therefore, we propose to use experimental concentration data, obtained for the migration of dimethyl sulfoxide (DMSO) through a stack of paper sheets, to infer the sorption constant. These concentrations are considered as the outcome of a model prediction and are inserted into an inverse boundary problem. We employ Physics-Informed Neural Networks (PINNs) to find the underlying sorption constant of DMSO on paper from this inverse problem. We illustrate how to practically combine PINN-based calculations with experimental data to obtain trustworthy transport-related material parameters. Finally we verify the obtained parameter by solving the forward migration problem via PINNs and finite element methods on the relevant time scale and show the satisfactory correspondence between the simulation and experimental results. Article Highlights: A mathematical model to describe transport of polar volatile organics through paper is proposed. Based on experimental data, the deep learning method of physics-informed neural networks (PINNs) is used to solve the inverse problem of finding the sorption time constant. Solutions for the forward problem are obtained by the standard finite element method (FEM) and PINN methods. These solutions are compared with each other as well as with the experimental data to verify the model. [ABSTRACT FROM AUTHOR]

The embossing operation is one of the processes of tissue paper converting. The embossing parameters influence the final properties of tissue products, such as mechanical, softness, and bulk. In this study, the influence of the rubber hardness used against the embossing steel rolls with a pattern created by intaglio engraving was studied. Three different configurations of rubber plates stacking, each plate with different hardness, were studied. After embossing, mechanical properties, softness, and bulk were evaluated to analyze the effect of rubbers hardness on these properties. Furthermore, a Finite Element Model of the embossing operation was used that considered the same rubber plates stacking configurations used in experiments, and it was able to replicate the experimental results. This work led us to conclude that the configuration where two rubber plates with different hardness, where the rubber plate with higher hardness is in contact with the tissue paper sheet, has shown to be the best solution to obtain higher softness. These findings support the use of embossing operations rubber rolls with a low hardness internal layer and a high hardness external layer in industry. Thus, finite element models were also shown to be reliable tools to virtually test other configurations, such as, for example, three or more rubber plates with different hardness. Since embossing is one of the tissue paper transformation operations with the greatest impact on the key properties of the final product, this study allows the producer to optimize them by varying the hardness of the rubber roll, as well as its configuration. [ABSTRACT FROM AUTHOR]

An innovative approach of using a laboratory embossing prototype was carried out to develop and optimize tissue papers, to quantify the influence of "deco" and "micro" embossing. A comparison between non-embossed and embossed tissue papers was conducted to investigate the effect of this process, on industrial and laboratory-made structures, evaluated by mechanical and softness properties. To identify the influence of the embossing patterns, the fiber composition and the creping process, a creped industrial base tissue paper, a disintegrated fibrous suspension obtained from this one, and an industrial never-dried bleached eucalyptus kraft pulp, were used as samples. These last two materials were used to produce similar industrial base tissue paper, in other words, handsheets with a grammage of 17 g/m2 and unpressed. The end-use tissue properties were evaluated on the non-embossed and embossed structures. The results indicated that the embossing process produced bulkier and more porous structures, at the expense of reduced mechanical and softness properties, more intensified in the "micro" embossing than in the "deco" embossing. The effect of fiber composition shows that the mechanical properties were increased with an adverse effect on the structures' TSA-softness. Furthermore, these properties are enhanced for the structures where creping process effects are presents. The performance of structures with and without embossing allowed to quantify the functional properties of softness and strength, combining ISO experimental methods and computational approaches that benefit from modeling strategies considering its structural hierarchy at the fiber and structure levels, and the shape pattern used in the embossing process. Finite Element Model (FEM) analysis enabled a better understanding of how the embossing patterns affect the mechanical properties during the embossing process. The experimental results were validated using FEM simulation, which proved that "micro" pattern has a higher stress field value, and consequently a lower mechanical strength. Overall, the results indicate that the embossing prototype can be used as an opportunity to investigate the embossing process at laboratory scale and to optimize the final end-use tissue properties due to the controlled process parameters implemented in this methodology. [ABSTRACT FROM AUTHOR]

Strain sensors which are embeded in AMOLED are introduced and studied in this paper. High accuray strain sensing are achieved, resolution of the sensors are about 0.05%. By combing the strain sensors in the panel, mechanical behaviors can be monitored and studied in real time. The snesors are used to conduct the foldable AMOLED mechanical and reliability study. Dynamic and static strains and related mechanism are introduced and discussed. Finite element simulation models considering the mechanical properties of materials including hyperelasticity, viscoelasticity and creep are established. Finally, the strain sensors and finite element anlysis are combined to study the mechanical response of AMOLED under dynamic folding, static folding, and different temperature and humidity environments. [ABSTRACT FROM AUTHOR]

The concept of digital twins in bridge engineering is still vague and even confused with the Bridge Information Model (BrIM). Therefore, this study provides a detailed review of 42 papers related to digital twins in bridge engineering, focusing on a proper definition, key features and creation techniques for bridge digital twin (BDT). The paper also compares BDT and BrIM from the perspectives of their elements, features, fidelity, services provided, and degree of development. The applications of BDT at different life cycle stages are identified, and the related technologies are analyzed in detail. The results show that the research clusters of BDT are divided into geometric model generation, finite element model updating, and management and are focused on the operation and maintenance phase while lacking attention in the design and construction phase. Besides, a reference framework of BDT based on the life cycle of bridges is proposed, and directions for future research are suggested. [ABSTRACT FROM AUTHOR]