Search

This paper employs an overhang structure for axial flux permanent magnet motor to enhance the torque density. However, the overhang structure requires a computationally expensive 3-D finite-element method (FEM) for analysis, because a quasi-3-D FEM cannot be applied to such a geometry. Thus, in order to reduce the computational cost of above-mentioned topology, this paper adopts a field reconstruction method (FRM). The conventional FRM is applicable only in the case, where the slot pitch to teeth length ratio is the same along radial direction. To address this problem, we introduce a virtual air gap concept so that it can take into account parallel slot effect as well as overhang effect. In this paper, the effectiveness of the proposed method is verified by the 3-D FEM and experimental results. [ABSTRACT FROM AUTHOR]

A novel hybrid-flux permanent-magnet (PM) generator, which has both axial flux and radial flux, is proposed. An axial-flux PM generator is designed by a reluctance network method and the 3-D finite element method. Using these results, this paper proposes a radial-flux and hybrid-flux machine, whose main dimensions are chosen to the same values as a commercialized one. The proposed hybrid-flux machine has the largest output power per volume. The power density of the proposed generator is 9.4 times larger than that of the commercialized one. The efficiencies of the proposed hybrid generator and a radial generator are same as each other, and are larger than those of an axial and the commercialized generators. [ABSTRACT FROM AUTHOR]

This paper presents performance improvements of a double excitation synchronous motor by using a reluctance network (RN). The distinguishing feature of the double excitation principle is to use permanent magnets with high energy, while air-gap flux is flexibly controlled by field windings. Therefore, the first contribution of this paper focuses on maximizing air-gap flux range control. Second, an approach for torque ripple reduction is proposed by directly modifying air-gap flux according to the instantaneous torque profile. The achieved resultant torque stays almost constant for a case study. The validity of the RN method is examined by comparisons with 3-D finite element and experimental results for several machines. [ABSTRACT FROM AUTHOR]

This paper presents a dynamic thermal model which predicts the winding temperature of electrical machines at steady-state and transient conditions where windings are used in integrated battery chargers (IBCs) for DC charging in a stationary position. Using winding in high current charging process causes rising winding temperature which affects insulation life. Switched reluctance machines are a proper choice for using in electric vehicles (EVs) because of their advantages such as simple and sturdy structures. IBCs can reduce volume and weight of EVs and total cost is diminished because of integration. The analytical thermal model proposed in this paper can calculates the winding temperature in balanced and unbalanced currents injection because of the phase inductance in each rotor angle is distinct, so current excitation in each phase should be different for obtaining zero total torque and keeping rotor in a stationary position, also a reduced-order model is proposed with minor impact on the accuracy of the model. Special attention has been paid to monitor the winding temperature with considering the motor lifetime in DC charging mode, this view has not been addressed in IBCs before. The proposed model is then validated against experimental results and 3D finite element method. [ABSTRACT FROM AUTHOR]

Recently, dual-rotor motor (DRM) has emerged as an alternative for an induction motor (IM) or a permanent-magnet (PM) motor for electric vehicle application, due to its better drive performance and better torque density. This paper presents an analytical model for the hybrid IM-PM configuration of DRM. The analytical model can be used to predict induced bar currents, electromagnetic torque generated, and magnetic fields in various regions of the motor. The mentioned calculations are performed under steady-state conditions. The analytical method is developed using the subdomain model approach in 2-D polar coordinates. Appropriate governing equations along with boundary conditions across all the sub-domain regions of the DRM are employed to calculate the magnetic vector potential in all the regions. The developed analytical model has been validated with finite-element analysis for various operating conditions, and high accuracy has been achieved for all the results. [ABSTRACT FROM AUTHOR]

This paper presents the design of a switched reluctance machine (SRM) for off-road hybrid electric vehicle applications. SRMs are ideally suited for this application for their low cost, fault tolerance, and reliable operations. A multistage fast design methodology for SRM is presented in this paper. The process aims to determine the best speed at which the SRM would start single-pulse mode operation. This ensures the best efficiencies over the specified operating range. The machine is initially designed at that operating point using analytical design tools and then further optimized through finite-element analysis (FEA). The designed machine has been prototyped and then experimentally tested. [ABSTRACT FROM PUBLISHER]

The vibration characteristics of stator system of the interior permanent magnet synchronous motor for EV are deeply studied in this paper, the effectiveness of reducing the vibration by optimizing the vibro-inertance (acceleration admittance) of the stator system is validated. Firstly, the theory of the vibro-inertance matrix of stator system with single-point excitation and multi-point response is proposed, and the mathematical theory model of vibro-inertance matrix of prototype motor stator system is established. Secondly, a new method of 3D finite element method (FEM) be used to simulate and analysis the vibro-inertance's characteristics for the prototype's stator system. Then, the correctness of the theory and the FEM simulation is verified by the prototype source-path-contribution (SPC) experiment. And it is found that near some non-natural frequencies with large vibro-inertance amplitudes, although the amplitude of operating force is relatively small at these frequencies, the prototype still produces large vibrations. Finally, three methods for optimizing the vibro-inertance matrix of the stator system are further studied. These methods can effectively shift the inertance frequency band of the stator system and change the average value of the inertance's amplitude of the motor stator system in different frequency bands, thereby changing the vibration characteristics of the whole motor. [ABSTRACT FROM AUTHOR]

This paper proposes a novel hybrid excitation vernier permanent magnet machine (HE-VPM). The characteristics of the proposed machine are: 1) the PMs are embedded in the stator teeth, which is helpful for the heat dissipation; 2) the rotor is salient structure without PMs and windings, which ensures the reliability of high-speed operation; 3) the nonoverlapping concentrated winding shortens the end-connection, and improves the torque density, 4) only half of the stator teeth possess PMs, and the total amount of PMs are decreased; and 5) the dc current are injected to the armature coils, therefore, the exciting field can be adjusted flexibly. In this paper, the electromagnetic performance, including back electromotive force, torque, etc. are analyzed with finite element analysis. The results show that the proposed machine exhibits flexible field adjustment capability, which may be suitable for applications requiring wide speed range operation. Besides, it is found that, compared with the existing pure sinusoidal phase current, higher torque density can be obtained with dc-biased phase current under constant stator copper loss. [ABSTRACT FROM AUTHOR]

This paper presents an analytical approach to determine the air-gap magnetic field and the winding inductance in the brushless doubly-fed reluctance machine (BDFRM) with flux barriers. By dividing one flux guide layer into several segments, a calculus method based on magnetic circuit analysis is developed and specific analytical expression of the air-gap flux density is rigorously derived. Then, the included angle between fundamental components with the same pole pairs is also discussed. Based on the air-gap flux density distribution, the inductance expressions between different windings are also presented. Three kinds of finite element analysis models are established and studied. As a result, the accuracy of the analytical model can be verified by simulations and experimental data from an existing BDFRM prototype. [ABSTRACT FROM AUTHOR]

It is recognized that the rotor with shielding cylinder (SC) is one of the effective measures to restrain the rotor eddy current loss (RECL) for high-speed surface-mounted permanent magnet synchronous motors (PMSMs). At present, the RECL of PMSMs with multilayer composite rotor structure is mainly analyzed by the finite element method (FEM), which has obvious shortcomings in time-consumption and the mesh generation of thin SC. In this paper, a multi-layer subdomain analytical model for calculating the RECL of high-speed PMSMs with both non-ferromagnetic retaining sleeve and SC is proposed by taking the effects of eddy current reaction, stator slotting and current harmonics into account. Moreover, the 3-D distribution coefficient of eddy current in the SC is derived by the equivalent impedance method and the effects of temperature on the conductivity of the SC and RECL are obtained through equivalent thermal network (ETN) model. Based on the analytical model, the SC parameters are calculated to obtain the variation ranges when the RECL is minimum. Finally, the C-shape core experiment was built up to verify the correctness of the multilayer analytical model under different shielding layer conductivities and thicknesses. [ABSTRACT FROM AUTHOR]

Brushless doubly fed induction machine (BDFIM) which is able to operate in both induction mode and synchronous mode, has received increasing attention of researchers, in the last three decades. It could be considered as an emerging competitor for older structures, due to the substantial features such as brushless structure and requiring a fractionally rated frequency converter. The iron loss which constitutes a significant portion of total power losses is higher in BDFIM in contrast with standard induction machine. Even though it is essential to consider the iron loss effect on dynamic behavior of BDFIM, there is still no comprehensive study in the literature. The aim of this paper is to propose a dynamic model of BFIM in general reference frame in which the iron loss is taken into account. This model which is credible for all BDFIM operation modes including synchronous one, facilitates the performance analysis of BDFIM and implementation of the various control techniques. The supplementary simulations and experiments confirm that the proposed model is an appropriate candidate for BDFIM drives. Because of the complex structure of BDFIM, determination of the iron loss isn't straightforward. In this paper, a practical approach is introduced to calculate the iron loss of BDFIM in terms of frequency variations. The experimental data derived from a D132s prototype BDFIM is then compared with the calculated data from the finite element analysis (FEA). [ABSTRACT FROM AUTHOR]

This paper deals with the design and testing of an interior permanent-magnet (IPM) machine that exhibits advanced features. It adopts fractional-slot (FS) nonoverlapped coil windings that reduces the end winding length, i.e., the Joule losses and machine cost. As a consequence, higher rated current can be supplied so that higher torque density and higher efficiency in a wide operating region can be reached. The rotor saliency increases the performance in flux-weakening operating region and the fault-tolerance capability. In order to decrease the torque ripple, it is important to minimize the interaction between the magnetomotive force (MMF) harmonics due to the stator currents and the rotor anisotropy. To do that, the winding has been optimized so as to minimize the MMF harmonics, taking advantage from the higher degree of freedom of the four-layer winding. However, the so-called slot-harmonics cannot be minimized by rearranging the winding coils. Hence, the rotor geometry has been designed so as to minimize the impact of such slot-harmonics. A 12-slot 10-pole IPM FS machine has been designed and manufactured. The experimental tests confirm the expectations. [ABSTRACT FROM AUTHOR]

This paper focuses on the comparative analysis of modular spoke-type permanent magnet machines with two magnetization modes, which are referred to as M-I and M-II types. The analytical models of the proposed machines are built based on the simple magneto-motive-force-permeance method. With the help of finite element analysis and the analytical models, magnetic fields in machines with different magnetization modes are compared. Then, taking as a base an existing commercial in-wheel machine used in an electric motorcycle, two proposed machines with different magnetization modes are designed as in-wheel traction machines and compared with respect to electromagnetic torque, flux-weakening performance, over-load capability, etc. The machines are prototyped and experimentally tested to verify the prediction that the M-II machines exhibit a higher torque output whereas the M-I machines have a wider speed range. [ABSTRACT FROM AUTHOR]

This paper presents a study of the effects that the shoe shape of the teeth of electrical machines has on the performance and losses. This is done by considering a concentrated wound, high-speed permanent magnet generator. The paper investigates the influence of the tooth shoe shape on the machine magnetic circuit and the losses distribution based on analytical and finite-element analysis (FEA). A shape coefficient K {t} is proposed to provide an optimized design reference. A comprehensive analytical tool able to study the variations of the machine performance parameters is proposed. The deduced optimization function is normalized using the non-equilibrium relative weighting method, and then, it is processed via a genetic algorithm to achieve the optimized design. FEA is used to validate the proposed analytical tool and the optimum design. [ABSTRACT FROM AUTHOR]

This paper focuses on the analysis and design of a triple-rotor axial-flux spoke-array vernier permanent magnet (TR-AFSAVPM) machine. By cooperating with spoke-array rotor and coil-wounded winding, power factor and torque density of the proposed machine are much improved and its copper utilization is reduced comparing with conventional vernier machines. First, the machine structure and its operation principles are reviewed. After that, analytical equations of its back-electromotive force and torque are derived to reveal the machine characteristics. Based on both quasi-3-D finite element analysis (FEA) and 3-D FEA, its high torque density performance is verified and a set of optimized machine sizing specifications is ultimately settled. A fractional slot axial-flux permanent magnet (VPM) machine and an axial-flux surface VPM machine are designed to compare with the proposed configuration. Analysis results show that the TR-AFSAVPM machine has high power factor viz., 0.96 and high torque density viz., 24.2 kNm/m3. A prototype has been designed and tested to validate the results. No-load test result is illustrated in this paper and the rated load experiment will be added in the future. [ABSTRACT FROM AUTHOR]

From a new stator-flux perspective, a comparative study between the series and parallel hybrid excitation machine (PHEM) is conducted and it is revealed that in PHEMs there still exist distinct stator-flux harmonic components during high-speed flux weakening operation, which could be further utilized to improve the torque capability at high-speed range. Inspired by this idea, an auxiliary winding is creatively introduced into PHEMs to recycle and utilize the magnetic field energy generated during the field regulation. A new design case is presented in this paper, in which two sets of armature windings with different pole pair numbers are arranged to realize the function of flux weakening operation and energy recycling, respectively. The feasibility of this new hybrid solution is evaluated by using the finite-element analysis. Furthermore, a prototype is manufactured and relevant experiments are performed. The experimental results agree well with the theoretical analysis and simulation results, which verify that the recycled energy can be effectively used to boost the output torque and power of PHEMs in the high-speed region. [ABSTRACT FROM AUTHOR]

The main idea of this paper is to offer a continuous C-cores unique configuration for switched reluctance motor (SRM) and to present an analytical model for its analysis. The advantages of this structure are having a short path for the main part of the magnetic flux, resulting in less core losses and as well as less negative torque. On the other hand, there is less leakage flux in the proposed structure. Another advantage of this structure is that it has a high mean torque compared to conventional structures, so that this increase in mean torque also increases a small amount of torque ripple, which is negligible. However, power density at a constant volume increases relatively much. The proposed SRM is analyzed by the finite element method (FEM) and by employing a magnetic flux density pattern and magnetic fluxes path, its magnetic equivalent circuit (MEC) is obtained. In this MEC model, the main fluxes and leakage fluxes are fully modeled. After its complete analysis, electromagnetics torque, inductance, flux-linkage, mean torque, and peak torque are evaluated. Static and dynamic performances are then determined. Finally, the proposed SRM was prototyped and tested. The experimental results consisting of static torque, flux-linkage, voltage, and current waveforms and input power are compared with the corresponding results in the MEC model and FEM. The comparisons verify the accuracy and validity of the introduced analytical model. Besides, static torque, flux-linkage characteristics, and dynamic performance at a nominal speed of 1000 rpm and the current chopping control mode with chopping 5A under the load of the proposed SRM are compared with the conventional SRM and its merits are observed. [ABSTRACT FROM AUTHOR]

This paper describes a $d$– $q$-axis model of synchronous permanent-magnet machines at high frequency. Both the inductive and resistive saliencies are taken into account, and the model is suitable for investigating the self-sensing capability of the machines. It is proved that the high-frequency machine response can be described by means of three complex parameters, which form a symmetrical matrix. It is also shown that the high-frequency resistances between the $d$- and $q$-axes exist, and they may assume a negative value. Experimental results are included in this paper to prove the developed theory. [ABSTRACT FROM PUBLISHER]

In this paper, the ringed-pole surface-mounted permanent-magnet machine is investigated from the point of view of the ring losses. The rings around the poles create a high-frequency anisotropy that is useful to detect the rotor position by means of a high-frequency signal injection. However, the presence of the rings causes additional rotor losses. The causes of ring losses are investigated in the paper. The first cause is the high-frequency signal injection itself. The harmonics in the airgap magnetomotive force, which are not synchronous with the rotor and hence induce currents in the rings, are the second source of losses. The third source is the airgap flux fluctuation due to stator slotting. Machines of different sizes and winding types are investigated. A finite-element analysis and an analytical model are used to estimate the ring losses, comparing the results. The influence of the ring cross-sectional area on the ring losses is analyzed, showing that the ring losses can be reduced in certain configurations. [ABSTRACT FROM PUBLISHER]

The brushless doubly fed induction machine (DFIM) is a special machine type that is of interest as a generator in wind turbine drive trains. The brushless DFIM has a significant space-harmonic content compared with conventional machine types, due to its construction. This results in additional harmonic distortions, such as torque-ripple and time harmonics. This paper studies the causes and origins of harmonic distortions in the brushless DFIM. Using time- and space-harmonic analysis, an analytical evaluation method is derived to predict the torque ripple frequencies and time-harmonic frequencies in stator and rotor voltages and currents. The evaluation method is applied to a prototype brushless DFIM to demonstrate the severity of harmonic related distortions that can be present in the brushless DFIMs. The evaluation is validated by additional finite-element analysis and measurements. Furthermore, measures are proposed to reduce harmonic distortions. The insight into harmonic distortions in the brushless DFIM and the ability to predict and prevent them must lead to the improved brushless DFIM designs in the future. [ABSTRACT FROM PUBLISHER]

Electric continuously variable transmission (e-CVT) device is a key component in hybrid electric vehicles (HEVs), which serves to perform the energy transmission among the initial combustion engine, battery, and output shaft. This paper presents a novel consequent-pole PM magnetic-geared double-rotor machine (CPDRM) that utilizes the magnetic gearing effect to transmit the power with a high efficiency. The artistry of CPDRM is to insert a dc winding within the center of the stator on the circumferential direction. Therefore, the machine can extend the constant-power region by changing the current direction and amplitude of dc windings. Meanwhile, the flux density within the air gap is changed accordingly. Then, the working principle of CPDRM and the flux change process are illustrated by employing the magnetic circuit method. Finally, a finite-element method model is constructed to verify the performances of the CPDRM under different operating modes. The result shows that the proposed machine has an excellent flux-weakening ability, and it can serve as a suitable candidate as an e-CVT component for HEVs. [ABSTRACT FROM AUTHOR]

A new type of three-phase stator hybrid excited machine with permanent magnets (PMs) located at the slot openings of field winding slots is presented in this paper. It has the advantage of good flux regulation capability due to the field excitation. The machines with different stator/rotor pole combinations, i.e., 6-stator pole and 7-/8-/10-/11-/13-/14-rotor poles, have been comparatively investigated in terms of the open-circuit and on-load characteristics, as well as the influence of dc current and the unbalanced magnetic forces. The 2-D finite element analysis (FEA) has been employed for analysis and optimization of the machines together with experimental validation. [ABSTRACT FROM AUTHOR]

In previous studies, the field winding of the brushless pulsed alternator (BPA) is embedded in the stator slots, which is supplied by dc power or variable frequency power. The advantage is that the field current can be independently adjusted. It means that the BPA system needs a standalone excitation system, which will increase the volume and cost of the system. If we substitute electric excitation for permanent magnet excitation, not only the volume and cost of the BPA system can be decreased but the efficiency and flexibility can be enhanced. In this paper, the design schemes for electric excitation and permanent magnet excitation BPA are presented. For comparison, the stator and rotor dimensions of the two kinds of BPA are both the same. The characteristics of electric excitation and permanent magnet excitation BPA are analyzed by the finite-element method and field-circuit coupling method. Finally, the BPA systems with a resistive load are established, the performances of both the two excitation modes are compared. According to the simulation results, we conclude their advantages and disadvantages. [ABSTRACT FROM AUTHOR]

An optimal three-dimensional current computation flux weakening control strategy for dc-biased Vernier reluctance machines (VRMs) is proposed in this paper. Compared with permanent magnet synchronous machines, dc-biased VRMs have an additional degree of freedom to regulate the rotor flux through variable dc-biased armature current. The conventional flux weakening control strategy does not utilize the adjustable dc field current, and the output capacity in the flux weakening region is limited. In this paper, the optimal three-dimensional current distribution is calculated at the intersection of current and voltage constraint. Meanwhile, in order to maintain the armature voltage within the voltage constraint, the inductance nonlinearity is reflected by constructing the inductance table. The algorithm provides maximum output capability and high efficiency for dc-biased VRMs despite the changes in inductance parameters in the whole flux weakening region. Finally, the effectiveness of the proposed control strategy is validated by experimental results for a prototype machine. [ABSTRACT FROM AUTHOR]

This paper introduces a novel hybrid-excited stator slot opening permanent magnet (PM) machine (HSSPMM). The operation principle of the machine is described and the effects of rotor eccentricity and magnetic saturation due to PMs on electromagnetic performance, with particular emphasis on back electromotive force (EMF), are analyzed by finite element method (FEM). It shows that different from the conventional PM machines, the open-circuit back EMF in this novel HSSPMM should be zero but may become non-zero if significant magnetic saturation exists, and furthermore, the rotor eccentricity has a detrimental effect on the waveforms, amplitudes, and symmetries of three-phase back EMFs, as confirmed by FEM and tests. [ABSTRACT FROM AUTHOR]

This paper presents a novel consequent-pole hybrid brushless wound-rotor synchronous machine (CPH-BL-WRSM). The proposed machine employs permanent magnets (PMs) on the alternate poles of the salient pole rotor, which has considerably less magnet usage compared to the regular (PM) assisted synchronous machine. The proposed CPH-BL-WRSM offered the advantages of high starting torque, high torque density, and better performance under full-load conditions. The BL operation for the proposed machine is achieved by generating a composite magneto motive force (MMF) with a fundamental component and sub-harmonic component. The sub-harmonic component of the stator MMF is used for BL excitation of the rotor. The finite-element method was used to analyze the performance of the CPH-BL-WRSM in comparison with the performance of the existing BL-WRSM and regular PM-assisted BL-WRSM. Finally, a prototype of the CPH-BL-WRSM was manufactured and the experiment was conducted to demonstrate the performance of the proposed CPH-BL-WRSM. [ABSTRACT FROM AUTHOR]

A novel analysis for a new type of variable reluctance resolvers (VR-Resolvers) with toroidal windings based on the magnetic equivalent circuit (MEC) method is presented in this work. Different cases including various windings configurations as well as different rotor structures are considered in order to investigate the performance of the resolver precisely. The position error of both healthy and eccentric resolvers are studied by a flexible MEC model. The effect of the eccentricity fault on the resolvers with different specifications is also evaluated to analyze the manufacturing tolerance due to the eccentric rotor for several cases. It is notable that the presented MEC provides the opportunity to adjust accuracy and model several structures in both healthy and faulty conditions by just a single model. Finally, the MEC results are confirmed by finite element method and experimental results to show the effectiveness of the proposed model. In general, development of a new VR-Resolver and analyzing its performance under different windings configurations and rotor structures by proposing a modified MEC approach are the paper novelties. [ABSTRACT FROM AUTHOR]

Slotless permanent magnet machines are attractive in some modern drive and power generation fields, where the cogging torque and additional losses need to be minimized or removed. The stator slotless design can be combined with different surface permanent magnet (SPM) rotor topologies. In this paper, explicit analytical expressions are derived to analytically compute the slotless machine torque and no-load back Electro-Motive Force in the case of segmented SPM rotor with parallel, radial, or Halbach-array magnetization patterns. The expressions are found by solving the magnetic field due to the slotless stator winding and to the permanent magnet blocks; the latter modeled through equivalent surface current densities. The accuracy of the method is successfully assessed by comparison with the finite-element analysis (FEA). The proposed formulas are an effective alternative to the FEA to quickly compare different design solutions as well as to optimize them. Application examples are provided in which the presented method is adopted to define the machine cross section that maximizes the torque density. [ABSTRACT FROM PUBLISHER]

This paper presents the analysis of a brushless doubly fed reluctance machine (BDFRM) for renewable energy applications with an emphasis on the rotor design. The BDFRM stator includes two sets of windings, i.e., the control winding (CW) and power winding (PW). The PW is connected to the grid, while the CW links the grid by a power converter of fractional rating to regulate the operating speed. This reduces the converter cost, and the brushless configuration enhances the reliability. In this paper, the reluctance rotor of the BDFRM, which is similar to that of a synchronous reluctance machine, is designed and analyzed in order to improve the performance. The influence of the total MMF and its allocation to the two stator windings are also discussed in relation to the machine performance. Finite-element analysis is used for performance simulation. The experimental study validates the proposed design for a small BDFRM. [ABSTRACT FROM PUBLISHER]

This paper is about the mechanical design and analysis of a yokeless and segmented armature axial flux permanent-magnet (PM) synchronous machine, which consists of two external rotors and an inner stator. Although this new electrical machine has many advantages such as high torque density, shorter axial length, and high efficiency, its mechanical construction is yet challenging. This is mostly due to the high axial force between the stator and the two rotors, which can be further increased by the inevitable manufacturing and assembly tolerances. Based on the determined geometric dimensions of the electromagnetically relevant components, a reliable mechanical construction is developed in this paper. Subsequently, stress, deformation, thermal, and modal analyses are performed based on finite-element method (FEM). Finally, the first prototype is successfully manufactured and measured. It can be concluded that the proposed construction is reliable and the measured data match well with the results of the electromagnetic analysis. [ABSTRACT FROM AUTHOR]

This paper presents a fast method to compute wound rotor induction machines in steady state. Coupled time-harmonic finite-element (FE) circuit equation is used under a first space harmonic approximation for the air-gap magnetic field. It is shown that only four magnetostatic FE computations are necessary to determine the machine performances for any slip value. The performance comparison with a conventional complex magnetodynamic and time-stepping FE analyses show the effectiveness of the proposed approach. [ABSTRACT FROM AUTHOR]

The paper details modern saturation modeling and performance calculation to the analysis of grid-connected cylindrical wound-rotor synchronous motors. The developed models give reliable results with limited computation effort. The finite element based method uses iterative procedures to calculate the motor performance during which the motor parameters are evaluated in detail. Experimental results prove that the method has a high degree of accuracy and is computationally efficient. [ABSTRACT FROM AUTHOR]

In this paper, a novel E-Core transverse flux machine (TFM) is proposed. The machine has a double stator-single rotor configuration with flux concentrating ferrite magnets and pole windings across each leg of an E-Core stator. E-Core stators with the proposed flux-concentrating rotor arrangement result in better magnet utilization and higher torque density. The machine also has a modular structure facilitating simpler construction. This paper presents a single phase and a two-phase version of the E-Core machine. Case study for a 1 kW, 400 r/min machine for both the single phase and two-phase TFM is presented. [ABSTRACT FROM PUBLISHER]

This paper presents a new axial flux permanent magnet machine, named ring winding axial flux machine (AFM). The ring winding AFM (RWAFM) takes the advantage of segmented stator of yokeless and segmented armature topology with those of decoupled phases and ring winding of transverse flux topology. In this paper, the geometry of the RWAFM is introduced in detail. Furthermore, the working principle and torque production theory are discussed. To validate the concept and confirm manufacturability of the proposed topology, a prototype is fabricated. The performance of the RWAFM is studied through experimental tests, 3-D finite-element simulations, and analytical discussions. [ABSTRACT FROM PUBLISHER]

This paper presents an optimal design methodology of a dual-mechanical-port bidirectional flux-modulated machine for electric continuously variable transmission in hybrid electrical vehicles. The machine utilizes bidirectional flux modulation effect to combine two rotors and one stator together, aiming to realize electrical and mechanical power flexible split and combination. Due to the complexity of the machine structure, conventional optimization methods using analytical model are inapplicable. Therefore, an effective and practical method that combines the genetic algorithm and finite-element method (GA-FEM) is proposed to optimize the design of the machine in this paper. Since the computational cost increases exponentially with the increasing of number of design parameters, to reduce the computational cost in the optimization process, the design parameters are divided into two levels basing on a sensitivity analysis. And, then, the sensitive parameters are optimized using the GA-FEM coupled method. Finally, a prototype is fabricated to verify the effectiveness of the optimal design. [ABSTRACT FROM PUBLISHER]

In this paper, a new shaded-pole main exciter (ME) with additional short-circuited coils for aircraft three-stage starter–generator (SG) is proposed and investigated. The basic structure, winding configurations, operating principle, and start system structure of the presented shaded-pole ME are illustrated in detail. The comparative study between the original ME and the shaded-pole ME with respect to the starting mode performances is conducted by 2-D finite-element method (FEM). A prototype SG with original ME has been developed, and the experimental results are essentially consistent with the simulation results by the FEM utilized in the predictions in this paper. Simulation data and waveforms verify that the proposed shaded-pole ME is a good candidate for aircraft machines to satisfy the dual function of starter and generator. [ABSTRACT FROM AUTHOR]

In this paper, a new topology of a single-phase flux switching permanent magnet motor (FSPM) is presented. Unlike conventional FSPMs, the air-gap flux flows in the axial direction, and therefore, it is named the flux switching axial flux permanent magnet motor (FS AFPM). The proposed single-phase FS AFPM has a compact disc-type structure, four stator pole teeth, and two rotor pole teeth (4/2 combination). However, a number of the stator poles as well as the rotor poles can be easily increased, due to an enlarged circumferential length. It has two discs, one for the stator and other for the rotor. Like conventional FSPMs, this machine has a simple salient rotor pole structure. Along with the armature windings, the PMs are also embedded in the stator. A 3-D finite-element analysis is carried out for the characteristic analysis of the proposed single-phase FS AFPM. For the enhancement of the self-starting torque capability and unidirectional rotation, the rotor pole is tapered. [ABSTRACT FROM AUTHOR]

This paper investigates the influence of stator/rotor pole number combinations and permanent magnet (PM) numbers on electromagnetic performance of consequent-pole hybrid excited flux reversal machines (CP-HEFRMs), which have different numbers of PM poles and iron poles and concentrated AC and DC windings on the stator and a salient pole rotor. PMs in the slots of one stator pole are magnetized radially in the same direction, while opposite on adjacent stator poles. Magnetic field paths of DC, PM, and hybrid excitations are investigated. The phenomenon of flux cancellation, i.e., PM and DC MMFs in CP-HEFRMs are of opposite polarities in the flux-enhancing operating mode, is revealed and verified, for the first time, as the key feature that makes CP-HEFRMs different from other hybrid excited machines. Consequently, the saturation in stator pole and yoke can be mitigated and hence the overload capability of DC excitation is enhanced, which is verified by finite element analysis (FEA). Global optimizations are utilized to obtain the optimal rotor and stator pole number combinations and PM numbers for each stator pole. Torque, torque ripple, inductance, unbalanced magnetic force, and flux regulation capability are compared for different PM numbers and rotor pole numbers. Comparisons are made on consequent-pole and non-consequent-pole topologies in terms of torque capacity, flux regulation capability, and PM consumption to further illustrate the advantages of consequent-pole topology. A prototype machine is built and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

Consequent-pole (CP) permanent magnet (PM) configuration suffers asymmetric electromagnetic characteristics although it saves PM usage. The CP-based stator-PM synchronous machines are investigated in this paper, with particular reference to symmetrical issues. The electromagnetic performances of the CP-based stator-PM synchronous machines are firstly evaluated. Afterwards, the rule of even order harmonics cancellation is presented for different slot/pole number combinations and winding layouts, based on which symmetrical phase flux-linkages can be obtained although the unbalanced magnetic flux naturally occurs. Moreover, based on the three-dimensional finite element analysis, the unipolar end leakage-flux caused by the asymmetric magnetic field is identified, and the risk of the shaft magnetization is revealed. Finally, a pair of prototype machines are fabricated and measured to validate the analyses. [ABSTRACT FROM AUTHOR]

A partitioned stator-flux reversal (FR) permanent magnet machine (PS-FRPMM) is a new combination of a stator PM machine and a magnetically geared machine and has the specifications of both machines in terms of robust structure and torque density. In this paper, a comprehensive 2-D analytical model is developed for PS-FRPMM based on subdomain technique. The presented model has the capability to accurately and quickly investigate the effects of design parameters on the machine performance. The 2-D analytical model is evaluated on two case studies with 12 stator teeth and 10 rotor poles, and 18 stator teeth and 13 rotor poles, with four different magnetization patterns. The influences of various design parameters such as the rotor slot width, slot opening width, and the segment ratio of the PMs in the two-segment magnetization pattern have been investigated on the quantities, such as the instantaneous torque, torque ripple, unbalanced magnetic force (UMF), and electromotive force (EMF). For evaluating the presented analytical model, the 2-D finite element method (FEM) with and without saturation effects has been used. The comparative study between the analytical and numerical models shows good agreement. Finally, a 3-D FEM has been used, and the results of the 2-D analytical model and 3-D FEM are compared in terms of the accuracy and computational time. The results show that the presented model has lower computational time compared to the 2-D and 3-D FEM, while its accuracy is acceptable under different circumstances, such as saturation. [ABSTRACT FROM AUTHOR]

Special attention has been paid to two-phase switched reluctance motors (SRMs) as they have fewer power electronics components compared to three- or multi-phase ones. However, their main drawbacks are the lack of starting torque and a predetermined direction of rotation. This paper proposes a new self-starting technique for two-phase SRMs, which has superiorities over the previous approaches. In the proposed topology, the flux paths are shorter, and thus the required magnetomotive force is smaller, which reduces losses. The design procedure is explained. Two- and three-dimensional finite element method (FEM) is employed in the analysis. Also, the motor is prototyped, and two test setups for torque-angle measurement and control study are used. The dynamic behavior of the motor is studied applying single-pulse control and current hysteresis control strategies. The experimental results confirm the results obtained by FEM. Both simulation and experiment results confirm that the proposed topology offers higher efficiency, higher mean torque, and better dynamic behavior compared to two conventional SRMs. [ABSTRACT FROM AUTHOR]

Asymmetric interior permanent magnet (AIPM) rotor topologies can achieve torque enhancement in IPM synchronous machines without the increase of PM usage due to utilizing magnetic-field-shifting (MFS) effect by reducing the current angle difference between maximum PM and reluctance torque components. This paper investigates the influence of armature reaction on MFS effect in AIPM machines. A general model of IPM machines considering MFS effect is analytically developed and the AIPM and IPM machines using the same stator, rotor diameter and total PM amount are comparatively studied. It shows that the armature reaction affects the MFS effect in both AIPM and IPM machines and the influence is more significant in AIPM machine. The relationships between MFS effects in PM flux-linkage and inductance characteristics and current angles for maximum PM and reluctance torque components are revealed. It confirms that the change of current angles of torque components is due to the MFS effect in PM flux-linkage and inductance characteristics in both AIPM and IPM machines. Besides, the developed machine model considering MFS effect is verified by finite element analysis. Finally, a small-scale AIPM machine prototype is fabricated and measured to validate the finite element analysis. [ABSTRACT FROM AUTHOR]

In this paper, a novel six-phase outer rotor induction motor equipped with pseudo-concentrated windings is introduced as a robust, reliable, and low-cost solution. Multiple aspects of the proposed motor structure have been investigated such as a design algorithm and an analytical modeling based on the modified winding function considering the skew effect. The effect of using variable number of turns for the coils has been examined on the pseudo-concentrated windings. An appropriate optimization problem has been also defined to maximize the power factor and efficiency and to minimize the output torque ripple. The designed motor has been fabricated to verify the accuracy of the design procedure with an analytical model and a finite element analysis. Experimental results show superior performances for the designed motor. [ABSTRACT FROM AUTHOR]

This paper describes the iron losses calculation of an axial flux machine with yokeless and segmented armature structure based on the limited three-dimensional (3-D) finite element analysis (FEA) results corresponding to one-sixth electrical period. Considering, the 3-D magnetic flux in both stator segments and rotor yoke, soft magnetic composites are used to manufacture the soft magnetic components. Furthermore, time-consuming 3-D FEA is necessary to evaluate the performance of the machine accurately. Due to the magnetic periodicity, most of the characteristics of the machine can be easily determined through averaging the limited 3-D FEA results. However, in some models the calculation of iron losses requires always the flux density waveform in each soft magnetic composites (SMC) element of the FEA model for an entire electrical period, especially when the losses resulted by minor loops should also be taken into account. Therefore, a general method to reconstruct the complete flux density waveform in each SMC component of the FEA model based on limited 3-D FEA results is suggested in this paper. Subsequently, the iron losses can be calculated with various models in time or frequency domain. Finally, the suggested method is validated by comprising the measurement of a prototype with the calculated iron losses based on the classical Bertotti formula. [ABSTRACT FROM PUBLISHER]

This paper presents the results of experimental tests designed to verify analytical predictions of the rotor demagnetization characteristics of a 0.6 kW (cont.) 9-slot/6-pole fractional-slot concentrated winding (FSCW) interior permanent magnet (IPM) synchronous machine. The demagnetization characteristics of the rotor magnets in this commercially produced FSCW-IPM machine are measured using a test configuration that is designed to conduct multiple demagnetization tests on the same test machine under controlled temperature conditions. In this paper, finite-element (FE) predictions of the rotor demagnetization characteristics of the experimental machine during three-phase symmetrical short-circuit and single-phase asymmetrical short-circuit faults are presented. These results are compared with experimental test measurements of the postfault currents and the magnet flux density distribution following demagnetization, demonstrating very good agreement of many key features. These comparisons also confirm that 3-D effects and magnet material properties such as the magnet thermal coefficients have a significant impact on some details of the FE predictions of the machine's fault-mode response characteristics. [ABSTRACT FROM AUTHOR]

This paper presents an analytical equation that relates the number of broken bars in the rotor of an induction machine to the vibrations of its stator. The relation is given in terms of both amplitudes and frequencies and is validated by numerical and experimental investigations. The amplitude of vibrations of some frequency components is shown to increase quadratically with the number of broken bars when the motor is operated at rated load. The frequency components of interest are in the range of two to four times the value of the supply frequency, which simplifies the implementation with relatively low-cost instrumentation. The main focus and innovation of this paper is on the derivation of the analytical equations and their verification with numerical analysis, and the comparison of both results to the experimental measurements. [ABSTRACT FROM PUBLISHER]

The design rules of winding configurations and stator-pole/rotor-tooth (SP/RT) number combinations of doubly-fed flux-switching permanent magnet (DF-FSPM) machines are investigated in this paper based on coil electromotive force (EMF) vectors. The relationships between the components of stator and rotor coil-EMF vector diagrams are unveiled at first, including the numbers of stator and rotor phases, and the numbers of stator and rotor spokes. Then, the SP/RT number combinations are derived considering feasible stator/rotor phase number combinations and different winding configurations. The SP/RT number combinations are optimized considering the winding factors, magnetic field harmonics, unbalanced magnetic forces and machine diameter. It is shown that both of the stator and rotor pitch factors increase when the SP and RT numbers get closer. Furthermore, the influence of winding configurations and SP/RT number combinations on electromagnetic performances of DF-FSPM machines are analyzed by finite-element method. Finally, the analysis results are validated by experiment. [ABSTRACT FROM AUTHOR]

An interturn insulation failure in the field winding of synchronous motors is a common problem that can lead to degradation in performance and accelerated wear of motor components. Existing offline tests for detecting this fault are known to be unreliable and inconvenient to perform, as they require motor disassembly. Online monitoring based on airgap flux monitoring has been proven to be successful, but could lack sensitivity for cases where the number of turns per pole is large. In addition, field winding turn shorts can be intermittent depending on the centrifugal force and could be unobservable at standstill or under an steady state operation. Therefore, monitoring of the turn faults under standstill and starting conditions with high sensitivity and without motor disassembly is desirable. In this paper, the detection of field winding short circuits for salient pole synchronous motors based on an airgap search coil under the starting transient, and new methods for standstill testing without motor disassembly are proposed. Two-dimensional finite element analysis and experimental testing on a 30-kW motor are given to verify the claims made. It is shown that the proposed set of tests can provide sensitive and reliable detection of field winding short circuits under standstill and starting conditions. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual-stator brushless doubly-fed machine (DSBDFM) with cage-barrier rotor structure for torque density improvement in application of wind power generation. The torque density of electrical machine mainly relates to machine main dimensions and rotor coupling capability (CC). Therefore, optimizing the DSBDFM, especially the machine power distribution and rotor, affects machine torque density and rotor CC. At first, several rotor topologies are proposed and analyzed to strengthen rotor CC. Then, design principles and methods in deciding the main dimensions and power distribution for the developed DSBDFM are analyzed and illustrated in detail. Based on the machine structure and design methods, a 50-kW DSBDFM is designed, with outer and inner unit electrical machine power distribution, rotor CC, slot-pole combinations, and non-magnetic ring considered. The design example with detailed design procedure in this study provides designers a practical method in initial estimation of the dimensions and parameters for the designed DSBDFM. Meanwhile, a finite-element method is used to analyze performances of DSBDFM with winding series connection, which are verified by the experimental test. Through the results analysis, it is found that the designed DSBDFM satisfies the requirements with desirable performances, indicating the validity and rationality of design methods. [ABSTRACT FROM AUTHOR]

This paper presents a novel modular stator hybrid-excited synchronous machine with stator slot permanent magnets (PMs). By regulating the field current, the magnetic field, and consequently the back electromotive force, as well as the average torque can be controlled. The existence of stator slot PMs alleviates the magnetic saturation and improves the flux regulation ratio. The frozen permeability method is employed to investigate the torque contributions by different magnetic sources. Possible stator and rotor pole combinations are illustrated, and the corresponding electromagnetic performances are evaluated with the finite-element method. It is revealed that 12-stator pole machines with 11- and 13-rotor poles exhibit superior average torque and lower torque ripple due to even-order harmonics elimination. Finally, a prototype with modular stator segments is manufactured to validate the analyses and simulations. [ABSTRACT FROM AUTHOR]