Search

To ensure the safety of food contact materials, a liquid chromatography method was established to determine the migration of formaldehyde in paper packaging with various food simulants (10%, 25%, 50%, 75%, and 95% ethanol by volume) and to investigate the migration behavior of formaldehyde after various durations and with various materials. The results showed that the method has good linearity with a correlation coefficient of R 2  > 0.9990, a detection limit of 0.0011 ~ 0.0027 mg L -1 , and a spiked recovery of 89.7 ~ 103.2% in the range of formaldehyde determination; the migration of formaldehyde in all six paper contact materials showed a trend of gradual increase with time until equilibrium was reached. At the same time and temperature, the migration of formaldehyde in paper packaging was the highest in low-concentration ethanol. With the same food simulants and materials, the maximum migration of formaldehyde in printed materials was greater than that in nonprinted materials; with different materials and the same food simulant, the thickness value was higher, with the use of water-based ink as a printing material, and the maximum migration value of formaldehyde by offset printing technology was low., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Introduction: Alternative methods of dry storage and transportation may be a viable alternative to the use of liquid storage medium for cervical samples, especially for screening programs in places with few resources., Objective: The objective of this study is to verify the viability and efficacy of human papillomavirus DNA (HPV-DNA) detection in cervical cell samples collected and stored on a Flinders Technology Associates (FTA) card (Whatman Indicating FTA® Elute Micro Card) and subsequently recovered in ethanol-based liquid medium and to compare the results to those obtained using samples stored directly in ethanol-based liquid medium., Study Design: Thirty-four women submitted to ETZ (excision of the transformation zone of the cervix) were included in this study. Before ETZ, 2 samples of exfoliated cervical cells were collected from each woman by a doctor and stored in ethanol-based liquid medium and on an FTA card. DNA recovery from FTA samples was performed using ethanol-based liquid medium. Detection of HPV-DNA in the samples was performed using the Cobas® 4800 HPV Test Platform., Results and Conclusions: The HPV-DNA detection positivity rates were 70.6% for the samples collected directly in liquid medium and 64.7% for the samples stored on the FTA card, with high detection accuracy in the DNA samples recovered from the FTA card (area under the curve = 0.958; 95% confidence interval = 0.890-1.000). The concordance between the results obtained using the 2 storage media was 94.1% (Kappa = 0.866). These preliminary results suggest that collection of cervical material on an FTA card may be an alternative to storage in liquid medium since the liquid medium has some limitations. In addition, DNA recovery from the card using ethanol-based liquid medium streamlines the workflow in the laboratory and reduces the cost associated with reagents, thereby facilitating access to the HPV test in places with few resources and potentially improving cervical cancer screening., (© 2021 S. Karger AG, Basel.)

This work presents a novel development that exploits the concept of in-situ gas-separation together with a specific enzymatic colorimetric detection to produce a portable biosensor called "Blood Alcohol Micro-pad" for direct quantitation of ethanol in whole blood. The thin square device (25 mm × 25 mm × 1.8 mm) comprises two layers of patterned filter paper held together with a double-sided mounting tape with an 8-mm circular hole (the headspace). In operation, the reagent is deposited on one layer and covered with sticky tape. Then 8 μL of a blood sample is dispensed onto the opposite layer and covered with sticky tape. Diffusion of ethanol across the 1.6 mm narrow headspace permits selective detection of ethanol by the enzymatic reagents deposited on the opposite layer. This reagent zone contains alcohol oxidase, horseradish peroxidase and 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt, as the chromogenic reagent. The color intensity, measured from the recorded digital image, resulting from the enzymatic assay of ethanol, correlates with the concentration of blood alcohol. The results obtained with spiked mice and sheep blood samples, using an external calibration in the range of 1-120 mg dL -1 ethanol, gave recoveries of 93.2-104.4% (n = 12). The "Blood Alcohol Micro-pad" gave good precision with %RSD <1 (50 mg dL -1 ethanol, n = 10) and limit of quantification (10SD of intercept/slope) of 11.56 mg dL -1 . The method was successfully validated against a headspace gas chromatography-mass spectrometric method. It has good potential for development as a simple and convenient blood alcohol sensor for on-site testing., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Problems of stability were found for biomarkers of alcohol consumption: ethyl glucuronide (EtG), ethyl sulfate (EtS), phosphatidylethanols (PEths), and fatty acid ethyl esters (FAEEs) in whole blood. The purpose of this study was to establish a method for the determination of these four kinds of ethanol's non-oxidative metabolites in dried blood spots (DBS) by liquid chromatography tandem mass spectrometry (LC-MS/MS), and to evaluate their stability. In this method, 50 μL of human blood was spotted onto a filter paper for DBS analysis. Samples were extracted by methanol, reconstituted by 2-propanol, and injected into the LC-MS/MS system. Limits of detection were among 0.5-50 ng/mL, and deviations in accuracy and precision were all lower than 15% at three quality control levels. The stability of the four kinds of ethanol non-oxidative metabolites in DBS was investigated during a 90-day range under three temperatures, -20 °C, 4 °C, and 25 °C. EtG and EtS showed a high level of stability in DBS in the 90-day range, regardless of the temperature. FAEEs were unstable after three days. PEths showed stability within 15 days in postmortem DBS and 60 days in antemortem DBS, respectively, at all temperatures., Competing Interests: Declaration of Competing Interest The authors declare that they have no conflict of interest., (Copyright © 2019 Elsevier Inc. All rights reserved.)

Thermophilic methane fermentation was a valid approach for handling the stillage eluted from ethanol fermentation of waste paper and kitchen waste. The wide organic loading rate (OLR) range (2-14 g VTS/(L d)) for stable performance and relatively high energy recovery efficiency (79.0%) were achieved, and OLR of 8 g VTS/(L d) was optimum for achievement of highest biogas evolution and VTS removal efficiency. Microbial community analysis revealed that hydrolysis of cellulose was the critical step for methane production from the stillage., (Copyright © 2018 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.)

Efficient ethanol production from waste paper requires the addition of expensive nutrients. To reduce the production cost of ethanol from waste paper, a study on how to produce ethanol efficiently by adding kitchen waste (potentially as a carbon source, nutrient source, and acidity regulator) to waste paper was performed and a process of successive liquefaction, presaccharification, and simultaneous saccharification and fermentation (L+PSSF) was developed. The individual saccharification performances of waste paper and kitchen waste were not influenced by their mixture. Liquefaction of kitchen waste at 90°C prior to presaccharification and simultaneous saccharification and fermentation (PSSF) was essential for efficient ethanol fermentation. Ethanol at concentrations of 46.6 or 43.6g/l was obtained at the laboratory scale after fermentation for 96h, even without pH adjustment and/or the addition of extra nutrients. Similarly, ethanol at a concentration of 45.5g/l was obtained at the pilot scale after fermentation for 48h. The ethanol concentration of L+PSSF of the mixture of waste paper and kitchen waste was comparable to that of PSSF of waste paper with added nutrients (yeast extract and peptone) and pH adjustment using H 2 SO 4 , indicating that kitchen waste is not only a carbon source but also an excellent nutrient source and acidity regulator for fermentation of the mixture of waste paper and kitchen waste., (Copyright © 2017. Published by Elsevier Ltd.)

Herein, we report the first example of a paper-based screen-printed biosensor for the detection of ethanol in beer samples. Common office paper was adopted to fabricate the analytical device. The properties of this paper-based screen-printed electrode (SPE) were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and scanning electron microscopy, and they were compared with the well-established polyester-based SPEs as well. Paper demonstrated similar properties when compared with polyester, highlighting suitability towards its utilization in sensor development, with the advantages of low cost and simple disposal by incineration. A nanocomposite formed by Carbon Black (CB) and Prussian Blue nanoparticles (PBNPs), namely CB/PBNPs, was utilized as an electrocatalyst to detect the hydrogen peroxide generated by the enzymatic reaction between alcohol oxidase (AOx) and ethanol. After optimizing the analytical parameters, such as pH, enzyme, concentration, and working potential, the developed biosensor allowed a facile quantification of ethanol up to 10 mM (0.058 % vol ), with a sensitivity of 9.13 μA/mM cm 2 (1574 μA/% vol cm 2 ) and a detection limit equal to 0.52 mM (0.003% vol ). These satisfactory performances rendered the realized paper-based biosensor reliable over the analysis of ethanol contained in four different types of beers, including Pilsner, Weiss, Lager, and alcohol-free. The proposed manufacturing approach offers an affordable and sustainable tool for food quality control and for the realization of different electrochemical sensors and biosensors as well., (Copyright © 2017 Elsevier B.V. All rights reserved.)

Medium-chain fatty acids (MCFA, e.g., caproic, heptanoic, caprylic acid) are more valuable than short-chain fatty acids (SCFA, e.g., acetic, propionic, butyric, valeric acid). SCFAs are major products in methane-inhibited mixed-culture anaerobic fermentation. By feeding ethanol to the fermentor, MCFA formation is enhanced through chain elongation. Microorganisms such as Clostridium kluyveri elongate short-chain acids by combining them with alcohol. Very low ethanol concentration reduces chain elongation rates, whereas very high ethanol concentrations inhibit microorganisms. To maximize MCFA production, different ethanol concentrations were investigated in the mixed-culture fermentation of office paper and chicken manure. At 10 g/L ethanol concentration, 10 g/L MCFA was formed. High ethanol concentrations (above 40 g/L) inhibit microorganisms resulting in no chain elongation. For chain elongation, propanol was found to be more inhibitory than ethanol. The data suggest that MCFA production will increase by continuously extracting MCFA and maintaining 5-10 g/L ethanol concentration by periodic addition. Biotechnol. Bioeng. 2016;113: 2597-2604. © 2016 Wiley Periodicals, Inc., (© 2016 Wiley Periodicals, Inc.)

Primary sludge, from different pulp and paper mills, was used as feedstock in simultaneous saccharification and fermentation (SSF) processes to produce ethanol. SSF was carried out with Saccharomyces cerevisiae ATCC 26602 yeast and NS 22192 enzymatic extract using 150gL(-1) of carbohydrates (CH) from primary sludge. The effect of sterilization, reduction of enzyme dosage and fed-batch vs. batch conditions were studied. The removal of sterilization can be considered since no contamination or atypical by-products were observed, although SSF efficiency slightly decreased. The reduction of the enzyme dosage from 35 to 15FPUgCH(-1) was successful. Despite of initial mixing difficulties, batch SSF enabled higher ethanol concentration (41.7gL(-1)), conversion yield (48.9%) and productivity (0.78gL(-1)h(-1)), compared to the fed-batch process at the same conditions of low enzyme dosage of 5FPUgCH(-1) and high solids content of 21.7%, rarely found in literature., (Published by Elsevier Ltd.)

The feasibility of cellulase recycling in the scope of bioethanol production from recycled paper sludge (RPS), an inexpensive byproduct with around 39% of carbohydrates, is analyzed. RPS was easily converted and fermented by enzymes and cells, respectively. Final enzyme partition between solid and liquid phases was investigated, the solid-bound enzymes being efficiently recovered by alkaline washing. RPS hydrolysis and fermentation was conducted over four rounds, recycling the cellulases present in both fractions. A great overall enzyme stability was observed: 71, 64 and 100% of the initial Cel7A, Cel7B and β-glucosidase activities, respectively, were recovered. Even with only 30% of fresh enzymes added on the subsequent rounds, solid conversions of 92, 83 and 71% were achieved for the round 2, 3 and 4, respectively. This strategy enabled an enzyme saving around 53-60%, while can equally contribute to a 40% reduction in RPS disposal costs., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

This work evaluates the environmental performance of using pulp and paper sludge as feedstock for the production of second generation ethanol. An ethanol plant for converting 5400 tons of dry sludge/year was modelled and evaluated using a cradle-to-gate life cycle assessment approach. The sludge is a burden for pulp and paper mills that is mainly disposed in landfilling. The studied system allows for the valorisation of the waste, which due to its high polysaccharide content is a valuable feedstock for bioethanol production. Eleven impact categories were analysed and the results showed that enzymatic hydrolysis and neutralisation of the CaCO3 are the environmental hotspots of the system contributing up to 85% to the overall impacts. Two optimisation scenarios were evaluated: (1) using a reduced HCl amount in the neutralisation stage and (2) co-fermentation of xylose and glucose, for maximal ethanol yield. Both scenarios displayed significant environmental impact improvements., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Paper sludge (PS) from the paper and pulp industry consists primarily of cellulose and ash and has significant potential for ethanol production. Thirty-seven PS samples from 11 South African paper and pulp mills exhibited large variation in chemical composition and resulting ethanol production. Simultaneous saccharification and fermentation (SSF) of PS in fed-batch culture was investigated at high solid loadings and low enzyme dosages. Water holding capacity and viscosity of the PS influenced ethanol production at elevated solid loadings of PS. High viscosity of PS from virgin pulp mills restricted the solid loading to 18% (w/w) at an enzyme dosage of 20 FPU/gram dry PS (gdPS), whereas an optimal solid loading of 27% (w/w) was achieved with corrugated recycle mill PS at 11 FPU/gdPS. Ethanol concentration and yield of virgin pulp and corrugated recycle PS were 34.2g/L at 66.9% and 45.5 g/L at 78.2%, respectively., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Waste paper can serve as a feedstock for ethanol production due to being rich in cellulose and not requiring energy-intensive thermophysical pretreatment. In this study, an efficient process was developed to convert waste paper to ethanol. To accelerate enzymatic saccharification, pH of waste paper slurry was adjusted to 4.5-5.0 with H2SO4. Presaccharification and simultaneous saccharification and fermentation (PSSF) with enzyme loading of 40 FPU/g waste paper achieved an ethanol yield of 91.8% and productivity of 0.53g/(Lh) with an ethanol concentration of 32g/L. Fed-batch PSSF was used to decrease enzyme loading to 13 FPU/g waste paper by feeding two separate batches of waste paper slurry. Feeding with 20% w/w waste paper slurry increased ethanol concentration to 41.8g/L while ethanol yield decreased to 83.8%. To improve the ethanol yield, presaccharification was done prior to feeding and resulted in a higher ethanol concentration of 45.3g/L, a yield of 90.8%, and productivity of 0.54g/(Lh). Ethanol fermentation recovered 33.2% of the energy in waste paper as ethanol. The biochemical methane potential of the stillage eluted from ethanol fermentation was 270.5mL/g VTS and 73.0% of the energy in the stillage was recovered as methane. Integrating ethanol fermentation with methane fermentation, recovered a total of 80.4% of the energy in waste paper as ethanol and methane., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Paper mill sludge (PS), a solid waste from pulp and paper industry, was investigated as a feedstock for acetone-butanol-ethanol (ABE) production by simultaneous saccharification and fermentation (SSF). ABE fermentation of paper sludge by Clostridium acetobutylicum required partial removal of ash in PS to enhance its enzymatic digestibility. Enzymatic hydrolysis was found to be a rate-limiting step in the SSF. A total of 16.4-18.0g/L of ABE solvents were produced in the SSF of de-ashed PS with solid loading of 6.3-7.4% and enzyme loading of 10-15FPU/g-glucan, and the final solvent yield reached 0.27g/g sugars. No pretreatment and pH control were needed in ABE fermentation of paper sludge, which makes it an attractive feedstock for butanol production. The results suggested utilization of paper sludge should not only consider the benefits of buffering effect of CaCO3 in fermentation, but also take into account its inhibitory effect on enzymatic hydrolysis., (Published by Elsevier Ltd.)

We have developed a new method for unprocessed biological specimens as templates directly into the TaqMan assay. Saliva was needed to be put on a water-soluble paper and dried, because foreign substances, such as a filter paper, hinder fluorescence detection through the assay. Genotyping of alcohol metabolism-related genes ADH1B (rs1229984) and ALDH2 (rs671) polymorphisms was, subsequently, performed by TaqMan PCR assay using dried saliva in the present investigation. The optimized technique was tested on 114 samples of alcoholic patients. The PCR-RFLP methods with purified DNA from blood samples were employed for validation of the assay. Upon validation, complete concordance was observed between the two independent results. These results highlight the ability of TaqMan PCR assays using dried saliva on water-soluble paper in genotyping of ADH1B and ALDH2 genes. Our results showed a rapid, simple, reliable, and cost-effective method for SNP genotyping of mutations in ADH1B and ALDH2 genes. This will be very useful for large-scale association studies in various fields. [Original].

The present work deals with intensification of bioethanol production from waste newspaper using Saccharomyces cerevisiae using ultrasonic irradiations. The effect of different process parameters such as application of ultrasonic irradiation at different growth phases, irradiation time, ultrasonic power and duty cycle on the bioethanol production has been investigated. The favorable conditions for the maximum yield were established as application of ultrasonic irradiation (duration of 10 min) to fermentation broth at 12 h of growth phase with 25 kHz frequency, 160 W power and 20% duty cycle. The bioethanol productivity was increased by 1.8 times from 7.8 to 14.1 g/L compared with the non-sonicated control fermentation. Decrease in glucose concentration from 0.63% to 0.2% w/v in ultrasound-assisted fermentation confirmed the improved substrate uptake of the microbial cell due to the application of ultrasound. ESEM analysis also confirmed the changes in the cell morphology leading to improved cell permeability. Results were fitted to an unstructured kinetic model comprising of the kinetic and physiological parameters. Overall, the work has demonstrated an intensified approach for the bioethanol production based on the use of ultrasound., (Copyright © 2015 Elsevier B.V. All rights reserved.)

In this study we investigated the technical feasibility of convert paper mill sludge into fuel ethanol. This involved the removal of mineral fillers by using either chemical pretreatment or mechanical fractionation to determine their effects on cellulose hydrolysis and fermentation to ethanol. In addition, we studied the effect of cationic polyelectrolyte (as accelerant) addition and hydrogen peroxide pretreatment on enzymatic hydrolysis and fermentation. We present results showing that removing the fillers content (ash and calcium carbonate) from the paper mill sludge increases the enzymatic hydrolysis performance dramatically with higher cellulose conversion at faster rates. The addition of accelerant and hydrogen peroxide pretreatment further improved the hydrolysis yields by 16% and 25% (g glucose / g cellulose), respectively with the de-ashed sludge. The fermentation process of produced sugars achieved up to 95% of the maximum theoretical ethanol yield and higher ethanol productivities within 9h of fermentation., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Recent advances in electrochemical analysis on filter paper exemplify the versatility of this substrate for high performance testing. Its low-cost, light-weight, and environmentally friendly properties make it particularly attractive for applications in addressing health and environmental safety needs in low-resource settings and developing countries. However, the main drawback to sensitive electrochemical testing is the use of a potentiostat, a bench-top instrument that is extremely expensive, thereby negating the some of the benefits of paper-based devices. Hence there is a need to develop paper-devices for use with handheld, portable device readers that can extract quantitative readouts. In this study, we developed a method to use micro-paper electrochemical devices, or µPEDs, with a glucose meter, which are used for personal monitoring of blood glucose levels. Ethanol was chosen as a model target analyte due to its importance in the global issue of road safety. µPEDs were simple in design and could be tested with a potentiostat. We observed that inclusion of the stabilizer trehalose was critical to preparing µPEDs for later analysis. In addition, an NAD(+)-dependent enzyme was used to impart selectivity to the biosensor, which also represents a class of enzymes with targets relevant to the health and food industry., (Copyright © 2014 Elsevier B.V. All rights reserved.)

Ethanol produced from lignocellulosic biomass is a renewable alternative to diminishing petroleum-based liquid fuels. In this study, the feasibility of ethanol production from waste paper using the separate hydrolysis and fermentation (SHF) was investigated. Two types of waste paper materials, newspaper and office paper, were evaluated for their potential to be used as a renewable feedstock for the production of fermentable sugars via enzymatic hydrolysis of their cellulose fractions. Hydrolysis step was conducted with a mixture of cellulolytic enzymes produced locally by Trichoderma reesei Rut-C30 (cellulase-overproducing mutant) and Aspergillus niger F38 cultures. Surfactant pretreatment effect on waste paper enzymatic digestibility was studied and Triton X-100 at 0.5 % (w w(-1)) has improved the digestibility of newspaper about 45 %. The effects of three factors (dry matter quantity, phosphoric acid pretreatment and hydrolysis time) on the extent of saccharification were also assessed and quantified by using a methodical approach based on response surface methodology. Under optimal hydrolysis conditions, maximum degrees of saccharification of newspaper and office paper were 67 and 92 %, respectively. Sugars released from waste paper were subsequently converted into ethanol (0.38 g ethanol g(-1) sugar) with Saccharomyces cerevisiae CTM-30101.

Paper sludge is an attractive biomass source for the conversion to ethanol due to its low cost and the lack of severe pretreatment required. Four sludges from pulp and paper operations including both virgin kraft (VK) and recycled and deinking (RD) paper mills were analyzed. A fractionation process using a laboratory screen was utilized to produce a fiber-rich stream for enzymatic hydrolysis. This process removed 82-98 % of the ash with fiber yields from 39 to 69 %. Even though sludges in both non-fractionated and fractionated scenarios were pH-adjusted, total sugar conversion was still improved by 12-27 % by fractionation with 4.5 times less acid required for pH adjustment. Fermentation of the fractionated sludges showed very high ethanol yields. Acid insoluble clay adsorbs 3-5 mg enzyme per gram of clay depending on enzyme dosage. Acid soluble CaCO3 adsorbs about half of the enzyme compared to clay. Fractionation efficiency was also evaluated by testing different size mesh screen openings (100 to 500 mesh). The 400-mesh screen presented the best fiber yield, ash removal and ash fractionation ratio for both VK and RD sludges. The ash-rich streams have a lower C/N ratio than the original sludge which improves its suitability as soil amendment.

Calcium hydroxide nanoparticles dispersed in ethanol or 2-propanol have been proposed for deacidification treatments of cellulose-based supports and are currently adopted by many paper and paintings conservators. There is however a risk inherent in this treatment: the dispersion would acquire a highly alkaline pH in the presence of moisture, absorbed by the dispersing alcohol solvents or by the cellulose-based support. Consequently, conditions of potential risk would be created for the structural integrity of the cellulosic supports, for some organic film-forming materials and some colouring matter. The simple tests conducted in this study clearly demonstrate that this risk is real, and suggest a cautious attitude in evaluating the suitability of these nano-dispersions for the treatment of some works of art. [ABSTRACT FROM AUTHOR]

During the storage of celluloid pictures for animation films over half a century, an interleave paper adhered to acrylic paint. The purpose of this study is to establish a methodology to cleanly remove the paper from the paint. A layered film, a replica of the celluloid pictures, adhered with paper was prepared and immersed in water or ethanol. The effect of these solvents on the peeling behavior was investigated using a peel test. The maximum peel force for the dry layered film in was distributed at ~0.5 N, independently of the peel speed. The peel force was significantly reduced after the layered film was immersed in pure water or ethanol. A morphological observation revealed that the dry paper was peeled off via the cohesive failure of the paper. After the layered film was immersed in pure water, the paper was also peeled off via cohesive failure. The layered film immersed in ethanol was peeled off at the paper/paint interface. To clear the effect of the volume change in the paint on peel behavior, the relative volume was determined via image analysis. The relative volume of paint was 1.56 in pure water and 1.37 in ethanol. It can be considered that the large difference in the volume of paint induces a large shear stress at the paint/paper interface. [ABSTRACT FROM AUTHOR]

A paper-based microfluidic detection device for the detection of ethanol is demonstrated in this work. The method is based on a fluorophore consisting of short-chain conjugated molecular unit susceptible to the protonation of its terminal pyridine groups, along with a carboxyl-functionalized sidechain that acts as a binder and renders it water-soluble. The resulting fluorescent paper device yields large fluorescence changes when exposed to reactions that yield H2O2 in aqueous solutions. Using an enzyme-catalyzed rection that produces H2O2 from ethanol, we developed a two-zone, cut-out paper device containing a reaction zone in which the ethanol-containing analyte is placed, and an adjacent sensor zone where we observe a fluorescence color shift proportional to the ethanol concentration. The limit of detection of the fluidic ethanol biosensor was 0.05 v/v% and the dynamic range was 0.05-2 v/v%. This method was employed to detect the alcohol concentration of consumer vodkas using only a paper sensor and a smartphone camera. [ABSTRACT FROM AUTHOR]

A paper-based microfluidic detection device for the detection of ethanol is demonstrated in this work. The method is based on a fluorophore consisting of short-chain conjugated molecular unit susceptible to the protonation of its terminal pyridine groups, along with a carboxyl-functionalized sidechain that acts as a binder and renders it water-soluble. The resulting fluorescent paper device yields large fluorescence changes when exposed to reactions that yield H2O2 in aqueous solutions. Using an enzyme-catalyzed rection that produces H2O2 from ethanol, we developed a two-zone, cut-out paper device containing a reaction zone in which the ethanol-containing analyte is placed, and an adjacent sensor zone where we observe a fluorescence color shift proportional to the ethanol concentration. The limit of detection of the fluidic ethanol biosensor was 0.05 v/v% and the dynamic range was 0.05–2 v/v%. This method was employed to detect the alcohol concentration of consumer vodkas using only a paper sensor and a smartphone camera.

Cellulose oxidative and hydrolytical degradation is one of the greatest problems for the conservation of paper supports. To contrast these degradation processes, both deacidification and reduction of the oxidized functions are needed. Dealing with original documents, it is often impossible to perform the two mentioned treatments in aqueous solutions and in a distinct subsequent way, because of the fragility of the artifacts. After studying, in a separate way, an effective deacidifier (calcium propionate) soluble in ethyl alcohol and many reducers (boron complexes), able to act in different non-aqueous solvents, it was decided to test a simultaneous method of deacidification and reduction in ethanol. This paper presents the chemical-physical results obtained by applying simple deacidification and simultaneous deacidification-reduction on laboratory paper samples that were artificially aged and then re-measured after 10 and 15 years of natural aging. Results show that all alcoholic treatments are very effective: papers are stable also after a long period of both artificial and natural aging. [ABSTRACT FROM AUTHOR]

Potassium methyl siliconate (PMS) was investigated as a simple physicochemical modification in aged paper using silane coupling technique. The PMS-based solution was shown to favor penetration in the cellulose fibers on the paper with suitable uptakes being achieved at low concentrations. The studies of the physicochemical properties of the treated paper (mechanical strength and alkalinity) demonstrated that, besides the required deacidification feature and high level of alkali reserves, the immersion treatment by PMS allowed the enhancement of the mechanical intensities of paper arising from the interaction between Si-OH generated in hydrolysis of PMS and C-OH of cellulose on the paper. Adding ethanol into PMS solution could significantly improve mechanical properties of the aged paper treated by the formula apart from modifying the flatness of the paper. Optimized treatment process was achieved by altering the ratio of ethanol to water in PMS-based solutions. Contact angle measurements indicated the occurrence of hydrophobic character of the papers in immersion treatment with PMS-based solutions. The easy availability of the materials and simplicity of the method rendered it convenient for treatment for aged paper documents. [ABSTRACT FROM AUTHOR]

Bacterial cellulose (BC) synthesized by Gluconacetobacter sucrofermentans CECT 7291 seems to be a good option for the restoration of degraded paper. In this work BC layers are cultivated and purified by two different methods: an alkaline treatment when the culture media contains ethanol and a thermal treatment if the media is free from ethanol. The main goal of these tests was the characterization of BC layers measured in terms of tear and burst indexes, optical properties, SEM, X-ray diffraction, FTIR, degree of polymerization, static and dynamic contact angles, and mercury intrusion porosimetry. The BC layers were also evaluated in the same terms after an aging treatment. Results showed that BC has got high crystallinity index, low internal porosity, good mechanical properties and high stability over time, especially when purified by the alkaline treatment. These features make BC an adequate candidate for degraded paper reinforcement. [ABSTRACT FROM AUTHOR]

Highlights: [•] We prepared a series of paper sheets incorporating titania-anchored hollow silica. [•] The papers showed high photocatalytic activity in the degradation of ethanol. [•] A new model coupling mass transfer and UV penetration has been developed. [•] The simulated UV profiles suggest a strong UV attenuation within the paper thickness. [•] Counter- and co-current modes show comparable photocatalytic activities. [Copyright &y& Elsevier]