Search

[Display omitted] The design and development of high-performance and long-life Pt-free catalysts for the oxygen reduction reaction (ORR) is of great important with respect to metal-air batteries and fuel cells. Herein, a new low-cost covalent organic frameworks (COFs)-derived Co N C single-atoms catalyst (SAC) is fabricated and compared with the engineered nanoparticle (NP) counterpart for ORR activity. The ORR performance of the SAC catalyst (Co SA @NC) surpasses the NP counterpart (Co NP -NC) under the same operation condition. Co SA @NC also achieves improved long-term durability and better methanol tolerance compared with the Pt/C. The zinc-air battery assembled by the Co SA @NC cathode delivers a higher power density and energy density than that of commercial Pt/C catalyst. Molecular dynamics (MD) is performed to explain the spontaneous evolution from clusters to single-atom metal configuration and density functional theory (DFT) calculations find that Co SA @NC possesses lower d -band center, resulting in weaker interaction between the surface and the O-containing intermediates. Consequently, the reductive desorption of OH*, the rate-determine step, is further accelerated. [ABSTRACT FROM AUTHOR]

The catalytic efficiency of the cathode is paramount in elevating the operational efficacy of low-temperature solid oxide fuel cells (LT-SOFCs) through expeditious facilitation of the oxygen reduction reaction (ORR). Cathode confronts formidable challenges due to oxygen reduction reaction (ORR) kinetics. This work aims to develop a high-performance cathode by doping strontium (Sr) into Nd 2- x Sr 2 x NiO 4. We synthesized a series of Nd 2- x Sr 2x NiO 4 (x : 0, 0.03, 0.06, 0.1) samples with varying Sr doping levels and evaluated their electrochemical performances. Nd2- x Sr 2 x NiO 4 with optimal ratio (x : 0.06) delivers the highest peak power density of 620–338 mw cm−2 at 550-470 °C among all four samples. The electrochemical impedance spectroscopy of the optimal composition revealed that Nd 2- x Sr 2 x NiO 4 exhibits low electrode polarization resistance of 0.34 Ω cm 2 , depicting its high catalytic performance and compatibility with the electrolyte and anode. Furthermore, XPS spectra also suggest higher surface oxygen vacancies than the other three samples, subsequently improving the conductivity and catalytic activity. Along with high power and OCVs, Nd 2- x Sr 2 x NiO 4 cathode-based SOFC is persistently stable for 40 h without significant degradation. These results conclusively point to demonstrating Nd 2- x Sr 2 x NiO 4 as a high-performing cathode for LT-SOFCs. [ABSTRACT FROM AUTHOR]

The influence of the heterogeneous interface is critical for the catalytic activity of the oxygen reduction reaction (ORR). This study demonstrates an enhancement of the electrocatalytic activity of the SrFe 0.9 Nb 0.1 O 3-δ (SFN113) electrode through the construction of a SrFe 0.9 Nb 0.1 O 3-δ -Sr 3 Fe 1.8 Nb 0.2 O 7-δ (SFN113-SFN327) heterogeneous interface. By coating varying amounts of Sr(NO 3) 2 (0.1 g, 0.2 g and 0.3 g) on SFN113 (1 g), SFN113/327 composite electrodes with different amounts of triple conducting oxide SFN327 are in-situ synthesized by high temperature calcination. Electrical Conductivity Relaxation (ECR) tests show that SFN327 has superior oxygen surface exchange performance compared to SFN113, especially at lower temperatures. At 550 °C, the oxygen surface exchange parameter of SFN327 is 4.23 times higher than that of SFN113. Symmetric cell tests with SFN113/327||BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3-δ (BCZYYb)||SFN113/327 configuration and single cell tests with Ni-BCZYYb||BCZYYb||SFN113/327 configuration indicate that the SFN113/327 composite electrode with a mass ratio of 1:0.2 displays the best electrocatalytic performance, achieving a power output of 502 mW cm−2 at 700 °C. The work not only in-situ synthesizes the SFN113/327 triple conducting composite electrode, but also introduces a novel method for developing proton conducting electrode materials. [ABSTRACT FROM AUTHOR]

Double perovskite oxide Pr 1-x Nd x BaFe 2 O 5+δ (PNBFx, x = 0.0–0.3) nanofiber were prepared using electrospinning and were evaluated as cathodes for solid oxide fuel cells (SOFCs). The crystalline structure, microstructure, and electrochemical performance of PNBFx were thoroughly investigated and discussed. The PNBFx nanofiber cathodes obtained after sintering at 800 °C crystallized in a tetragonal structure with the space group P 4/ mmm and had good chemical compatibility with SDC electrolytes at 900 °C for 4 h. Nd doping was found to increase the lattice parameter, while the average valence of praseodymium and iron content increased steadily in PNBFx. The Pr 0.8 Nd 0.2 BaFe 2 O 5+δ (PNBF02) nanofiber cathode exhibited the best performance with a polarization resistance (R p) of 0.072 Ω cm2 at 750 °C. When PNBF02 nanofiber was used as a single-cell cathode, the peak power density reached 1.52 W cm2 at 750 °C. All results indicate that double perovskite PNBF02 is a promising cathode material for SOFCs. [ABSTRACT FROM AUTHOR]

With the incorporation of heteroatomic B into single-atom Fe catalyst (Fe SA -NC), a catalyst named Fe SA -BNC with a configuration of Fe-N 3 B 1 had been synthesized for the oxygen reduction reaction (ORR). The low electronegativity of B induced charge redistribution around the active center Fe, thereby modulating the ORR activity. The Fe SA -BNC catalyst demonstrated an outstanding ORR performance in alkaline conditions, with a half-wave potential of 0.87 V. [Display omitted] • Coordination of low electronegativity B with Fe atom. • Regulating the charge states of the active site Fe. • The decrease of the d -band center of Fe promoting the desorption of ORR intermediates and enhancing the ORR performance. Despite extensive research has been conducted on atomic dispersion catalysts for various reactions, altering the electronic structure of the central metal to enhance electrochemical reactivity remains a challenging task. Herein, the electrochemical reactivity was considerably enhanced by introducing heteroatomic B to adjust the d -band of single Fe center. In specific, the obtained Fe SA -BNC catalyst demonstrated an outstanding ORR performance (E 1/2 = 0.87 V) and exhibited greater long-term durability in alkaline media compared to Pt/C. The performance of Fe SA -BNC in Zn–air battery was also higher than that of Pt/C. According to theoretical calculations, a downward shift in the d -band center of Fe was induced by introducing B, thereby improving the desorption of intermediates and facilitating the oxygen reduction reaction (ORR). [ABSTRACT FROM AUTHOR]

Environmental pollution due to the excessive consumption of fossil fuels for energy production is a critical global issue. Fuel cells convert chemical energy directly into electricity in a clean and silent electrochemical process, but face challenges related to hydrogen storage, handling, and transportation. The direct borohydride fuel cell (DBFC), utilizing sodium borohydride as a liquid fuel, is a promising alternative to overcome such issues but requires the design of cost-effective nanostructured electrocatalysts. In this study, we synthesized nitrogen-doped graphene anchoring Ni nanoparticles (Ni@NG) by thermal degradation of polyethylene terephthalate bottle waste with urea and metallic Ni, and evaluated it as a sustainable carbon support. Electrocatalysts were prepared by incorporating ultralow amounts (0.09 to 0.27 wt.%) of Pd into the Ni@NG support. The resulting PdNi@NG electrocatalysts were characterized using ICP-OES, XPS, TEM, N2-sorption analysis, XRD, and Raman and FTIR spectroscopy. Voltammetry assessed the materials' electrocatalytic activity for oxygen reduction and borohydride oxidation reactions in alkaline media, corresponding to the anodic and cathodic reactions in DBFCs. The electrocatalyst with 0.27 wt.% Pd loading (PdNi_15@NG) exhibited the best performance for both reactions. Consequently, it was employed as an anodic and cathodic material in a lab-scale DBFC, achieving a specific power of 3.46 kW gPd−1. [ABSTRACT FROM AUTHOR]

Single‐atom catalysts (SACs) have received significant interest for optimizing metal atom utilization and superior catalytic performance in hydrogen evolution reaction (HER), oxygen evolution reaction (OER), and oxygen reduction reaction (ORR). In this study, we investigate a range of single‐transition metal (STM1 = Sc1, Ti1, V1, Cr1, Mn1, Fe1, Co1, Ni1, Cu1, Zr1, Nb1, Mo1, Ru1, Rh1, Pd1, Ag1, W1, Re1, Os1, Ir1, Pt1, and Au1) atoms supported on graphyne (GY) surface for HER/OER and ORR using first‐principle calculations. Ab initio molecular dynamics (AIMD) simulations and phonon dispersion spectra reveal the dynamic and thermal stabilities of the GY surface. The exceptional stability of all supported STM1 atoms within the H1 cavity of the GY surface exists in an isolated form, facilitating the uniform distribution and proper arrangement of single atoms on GY. In particular, Sc1, Co1, Fe1, and Au1/GY demonstrate promising catalytic efficiency in the HER due to idealistic ΔGH* values via the Volmer‐Heyrovsky pathway. Notably, Sc1 and Au1/GY exhibit superior HER catalytic activity compared to other studied catalysts. Co1/GY catalyst exhibits higher selectivity and activity for the OER, with an overpotential (0.46 V) comparable to MoC2, IrO2, and RuO2. Also, Rh1 and Co1/GY SACs exhibited promising electrocatalysts for the ORR, with an overpotential of 0.36 and 0.46 V, respectively. Therefore, Co1/GY is a versatile electrocatalyst for metal‐air batteries and water‐splitting. This study further incorporates computational analysis of the kinetic potential energy barriers of Co1 and Rh1 in the OER and ORR. A strong correlation is found between the estimated kinetic activation barriers for the thermodynamic outcomes and all proton‐coupled electron transfer steps. We establish a relation for the Gibbs free energy of intermediates to understand the mechanism of SACs supported on STM1/GY and introduce a key descriptor. This study highlights GY as a favorable single‐atom support for designing highly active and cost‐effective versatile electrocatalysts for practical applications. [ABSTRACT FROM AUTHOR]

Here, an approach to produce a hierarchical porous Fe‐N‐C@TABOH catalyst with densely accessible high intrinsic active FeNx sites is proposed. The method involves a single‐step pyrolysis of Zn/Fe‐zeolitic imidazolate framework (Zn/Fe‐ZIF‐H) with tetrabutylammonium hydroxide (TABOH) micelles, which is obtained by utilizing TABOH as a structural template and electronic mediator at room temperature for a brief duration of 16 min. Notably, the yield of Zn/Fe‐ZIF‐H is 3.5 times that of Zn/Fe‐ZIF‐N prepared by conventional method. Results indicate that in addition to expediting synthesis and increasing yield of the Zn/Fe‐ZIF‐H, the TABOH induces a hierarchical porous structure and fosters the formation of more and higher intrinsic active FeNx moieties in Fex‐N‐C@TABOH, showing that TABOH is a multifunctional template. Crucially, the increased mesoporosity/external surface area and optimized microenvironment of Fe‐N‐C@TABOH significantly enhance ORR activity by facilitating the formation of high intrinsic active FeNx sites, increasing accessible FeNx sites, and reducing mass transfer resistance. Through structure tailoring and microenvironment optimization, the resulting Fe‐N‐C@TABOH exhibits superior ORR performance. DFT calculation further validates that the synergistic effect of these two factors leads to low ORR barrier and optimized *OH adsorption energy. This study underscores the importance of structure and electronic engineering in the development of highly active ORR catalysts. [ABSTRACT FROM AUTHOR]

Metal oxides containing La, Mn, and Co cations can catalyze oxygen reduction reactions (ORRs) in electrochemical processes. However, these materials require carbon support and optimal interactions between both compounds to be active. In this work, two approaches to prepare composites of La-Mn-Co-based compounds over carbon xerogel were developed. Using sol-gel methods, either the metal-based material was deposited on the existing carbon xerogel or vice versa. The metal oxide selected was the LaMn0.7Co0.3O3 perovskite, which has good catalytic behavior and selectivity towards direct ORRs. All the as-prepared composites were tested for ORRs in alkaline liquid electrolytes and characterized by diverse physicochemical techniques such as XRD, XPS, SEM, or N2 adsorption. Although the perovskite structure either decomposed or failed to form using those in situ methods, the materials exhibited great catalytic activity, which can be ascribed to the strengthening of the interactions between oxides and the carbon support via C-O-M covalent bonds and to the formation of new active sites such as the MnO/Co heterointerfaces. Moreover, Co-Nx-C species are formed during the synthesis of the metal compounds over the carbon xerogel. These species possess a strong catalytic activity towards ORR. Therefore, the composites formed by synthesizing metal compounds over the carbon xerogel exhibit the best performance in the ORR, which can be ascribed to the presence of the MnO/Co heterointerfaces and Co-Nx-C species and the strong interactions between both compounds. Moreover, the small nanoparticle size leads to a higher number of active sites available for the reaction. [ABSTRACT FROM AUTHOR]

Platinum-based intermetallic compounds (IMCs) play a vital role as electrocatalysts in a range of energy and environmental technologies, such as proton exchange membrane fuel cells. However, the synthesis of IMCs necessitates recombination of ordered Pt-M metallic bonds with high temperature driving, which is generally accompanied by side effects for catalysts' structure and performance. In this work, we highlight that semimetal atoms can trigger covalent interactions to break the synthesis-temperature limitation of platinum-based intermetallic compounds and benefit fuel-cell electrocatalysis. Attributed to partial fillings of p-block in semimetal elements, the strong covalent interaction of d-p π backbonding can benefit the recombination of ordered Pt-M metallic bonds (PtGe, PtSb and PtTe) in the synthesis process. Moreover, this covalent interaction in metallic states can further promote both electron transport and orbital fillings of active sites in fuel cells. The semimetal-Pt IMCs were obtained with a temperature 300 K lower than that needed for the synthesis of metal-Pt intermetallic compounds and reached the highest CO-tolerant oxygen reduction activity (0.794 A mg−1 at 0.9 V and 5.1% decay under CO poisoning) among reported electrocatalysts. We anticipate that semimetal-Pt IMCs will offer new insights for the rational design of advanced electrocatalysts for fuel cells. [ABSTRACT FROM AUTHOR]

Exploring highly active electrocatalysts as platinum (Pt) substitutes for the oxygen reduction reaction (ORR) remains a significant challenge. In this work, single Mn embedded nitrogen-doped graphene (MnN4) with and without halogen ligands (F, Cl, Br, and I) modifying were systematically investigated by density functional theory (DFT) calculations. The calculated results indicated that these ligands can transform the dyz and dxz orbitals of Mn atom in MnN4 near the Fermi-level into d z 2 orbital, and shift the d-band center away from the Fermi-level to reduce the adsorption capacity for reaction intermediates, thus enhancing the ORR catalytic activity of MnN4. Notably, Br and I modified MnN4 respectively with the lowest overpotentials of 0.41 and 0.39 V, possess superior ORR catalytic activity. This work is helpful for comprehensively understanding the ligand modification mechanism of single-atom catalysts and develops highly active ORR electrocatalysts. [ABSTRACT FROM AUTHOR]

[Display omitted] Developing an efficient and low-cost oxygen reduction electrocatalyst is essential for the application of aqueous zinc-air batteries (ZABs). Herein, we report a facile adsorption-confined pyrolysis strategy to fabricate the hybrid electrocatalyst (denoted as Co 9 S 8 /Co SA -PC) by embedding Co 9 S 8 nanoparticles into Co single atoms (Co-SAs) anchored porous carbon sheets for boosting oxygen reduction reaction (ORR) durability. In this strategy, the Co2+ ions are first absorbed into oxygen-rich porous carbon nanosheets and further form the Co-SAs with the help of thiourea in the following pyrolysis procedure, which is believed to be able to confine the generated Co 9 S 8 nanoparticles into carbon frameworks due to their interface interaction. Benefiting from the synergistic effect of different components, the obtained Co 9 S 8 /Co SA -PC electrocatalyst for ORR exhibits outstanding catalytic activity with a half-wave potential of 0.82 V and a distinguished long-term durability with a current retention of 80 % after cycling 80 h under alkaline conditions, which is superior to commercial Pt/C. Moreover, the assembled ZABs with Co 9 S 8 /Co SA -PC as cathodic catalyst deliver a high specific capacity of 764 mAh g Zn −1 at 10 mA cm−2 and the outstanding peak power density of up to 221.4 mW cm−2. This work provides a novel structure design strategy to prepare transition metal sulfide-based electrocatalysts with superior durability for ORR. [ABSTRACT FROM AUTHOR]

The advancement of economical and readily available electrocatalysts for the oxygen reduction reaction (ORR) holds paramount importance in the advancement of fuel cells and metal‐air batteries. Recently, 2D non‐metallic materials have obtained substantial attention as viable alternatives for ORR catalysts due to their manifold advantages, encompassing low cost, ample availability, substantial surface‐to‐volume ratio, high conductivity, exceptional durability, and competitive activity. The augmented ORR performances observed in metal‐free 2D materials typically arise from heteroatom doping, defects, or the formation of heterostructures. Here, the authors delve into the realm of electrocatalysts for the ORR, pivoting around metal‐free 2D materials. Initially, the merits of metal‐free 2D materials are explored and the reaction mechanism of the ORR is dissected. Subsequently, a comprehensive survey of diverse metal‐free 2D materials is presented, tracing their evolutionary journey from fundamental concepts to pragmatic applications in the context of ORR. Substantial importance is given on the exploration of various strategies for enhancing metal‐free 2D materials and assessing their impact on inherent material performance, including electronic properties. Finally, the challenges and future prospects that lie ahead for metal‐free 2D materials are underscored, as they aspire to serve as efficient ORR electrocatalysts. [ABSTRACT FROM AUTHOR]

Rechargeable zinc-air batteries (ZABs) are regarded as a remarkably promising alternative to current lithium-ion batteries, addressing the requirements for large-scale high-energy storage. Nevertheless, the sluggish kinetics involving oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) hamper the widespread application of ZABs, necessitating the development of high-efficiency and durable bifunctional electrocatalysts. Here, we report oxygen atom-bridged Fe, Co dual-metal dimers (FeOCo-SAD), in which the active site Fe-O-Co-N6 moiety boosts exceptional reversible activity toward ORR and OER in alkaline electrolytes. Specifically, FeOCo-SAD achieves a half-wave potential (E1/2) of 0.87 V for ORR and an overpotential of 310 mV at a current density of 10 mA cm-2 for OER, with a potential gap (ΔE) of only 0.67 V Meanwhile, FeOCo-SAD manifests high performance with a peak power density of 241.24 mW cm-2 in realistic rechargeable ZABs. Theoretical calculations demonstrate that the introduction of an oxygen bridge in the Fe, Co dimer induced charge spatial redistribution around Fe and Co atoms. This enhances the activation of oxygen and optimizes the adsorption/desorption dynamics of reaction intermediates. Consequently, energy barriers are effectively reduced, leading to a strong promotion of intrinsic activity toward ORR and OER. This work suggests that oxygen-bridging dual-metal dimers offer promising prospects for significantly enhancing the performance of reversible oxygen electrocatalysis and for creating innovative catalysts that exhibit synergistic effects and electronic states. [ABSTRACT FROM AUTHOR]

Proton Exchange Membrane Fuel Cells (PEMFCs) represent a promising green solution for energy production, traditionally relying on platinum-group-metal (PGM) electrocatalysts. However, the increasing cost and limited global availability of PGMs have motivated extensive research into alternative catalyst materials. PGM-free oxygen reduction reaction (ORR) catalysts typically consist of first-row transition metal ions (Fe, Co) embedded in a nitrogen-doped carbon framework. Key factors affecting their efficacy include intrinsic activity and catalyst degradation. Thus, alternative materials with improved characteristics and the elucidation of reaction and degradation mechanisms have been the main concerns and most frequently explored research paths. High intrinsic activity and active site density can ensure efficient reaction rates, while durability towards corrosion, carbon oxidation, demetallation, and deactivation affects cell longevity. However, when moving to the actual application in PEMFCs, electrode engineering, which involves designing the catalyst layer, and other critical operational factors affecting fuel cell performance play a critical role. Electrode fabrication parameters such as ink formulation and deposition techniques are thoroughly discussed herein, explicating their impact on the electrode microstructure and formed electrochemical interface and subsequent performance. Adjusting catalyst loading, ionomer content, and porosity are part of the optimization. More specifically, porosity and hydrophobicity determine reactant transport and water removal. High catalyst loadings can enhance performance but result in thicker layers that hinder mass transport and water management. Moreover, the interaction between ionomer and catalyst affects proton conductivity and catalyst utilization. Strategies to improve the three-phase boundary through the proper ionomer amount and distribution influence catalyst utilization and water management. It is critical to find the right balance, which is influenced by the catalyst–ionomer ratio and affinity, the catalyst properties, and the layer fabrication. Overall, understanding how composition and fabrication parameters impact electrode properties and behaviour such as proton conductivity, mass transport, water management, and electrode–electrolyte interfaces is essential to maximize electrochemical performance. This review highlights the necessity for integrated approaches to unlock the full potential of PGM-free materials in PEMFC technology. Clear prospects for integrating PGM-free catalysts will drive cleaner and more cost-effective, sustainable, and commercially viable energy solutions. [ABSTRACT FROM AUTHOR]

The key factors in achieving high energy efficiency for proton exchange membrane fuel cells are reducing overpotential and increasing the oxygen reduction rate. Based on first-principles calculations, we induce H atom adsorption on 4 × 4 × 1 monolayer MoSe2 to induce spin polarization, thereby improving the catalytic performance. In the calculation of supercells, the band unfolding method is used to address the band folding effect in doped systems. Furthermore, it is evident from analyzing the unique energy band configuration of MoSe2 that a higher valley splitting value has better catalytic effects on the oxygen reduction reaction. We believe that the symmetries of the distinct adsorption site result in different overpotentials. In addition, when an even number of hydrogen atoms is adsorbed, the monolayer MoSe2 has no spin polarization. The spin can affect the electron transfer process and alter the hybrid energy with the reaction products, thereby regulating its catalytic performance. [ABSTRACT FROM AUTHOR]

[Display omitted] Solar light-driven hydrogen peroxide (H 2 O 2) production through the two-electron oxygen reduction reaction (ORR) from the earth-abundant O 2 and water is a potential alternative to the energy-consuming anthraquinone oxidation process, although the activity of the common photocatalysts is still insufficient to satisfy the industrial demands. Poor accessibility of O 2 to surface/interface and fast carrier recombination is the limiting-factor for catalytic systems. Herein, we develop a nanohybrid photocatalysts by introducing 1D conducting polymer of polypyrrole (PPy) nanotube on In 4 SnS 8 to promote H 2 O 2 evolution under visible light, obtaining up to 254.8 μM in 2 h, which is 2.4- and 13-fold larger than that of individual In 4 SnS 8 and PPy. The detailed characterizations of hybrid structure, O 2 adsorption behaviors, charge carrier dynamics over PPy/In 4 SnS 8 in conjunction with computational calculations corroborate that the modification of PPy could enlarge the amount of O 2 adsorption amount, expedite the cycle of O 2 adsorption/desorption and accelerate the transportation of electrons from In 4 SnS 8 to the interface, eventually speeding up H 2 O 2 photoproduction via indirect 2e− ORR pathway. This work establishes a paradigm of regulating the interfacial microenvironment by polymer for boosting H 2 O 2 photogeneration through high selectivity of ORR. [ABSTRACT FROM AUTHOR]

The unique properties of solid acid electrolytes, in particular CsH2PO4, are in many ways ideal for fuel cell operation. However, the technology is constrained by high cathode overpotentials. Here a simplified cathode geometry is employed to obtain the fundamental electrochemical parameters (exchange current density and charge transfer coefficient) describing the oxygen reduction reaction (ORR) at the CsH2PO4‐Pt‐gas interface. The parameters are incorporated into a 1D model of the voltage–current characteristics of realistic SAFC cathodes, which reproduced the measured polarization behavior of such cathodes without recourse to fitting adjustable parameters. Following this validation, the model is utilized to evaluate the impact of changes to cathode properties, microstructure, and operating conditions. Of these, the charge transfer coefficient, measured to have a value of ≈0.6 for ORR on Pt in the SAFC cathode environment, is found to have the greatest impact on power output. Nevertheless, even without material modifications, a combination of microstructural and operational modifications are identified with projected performance metrics meeting Department of Energy targets (0.8 V at 300 mA cm−2, and peak power density of 1 W cm−2), albeit at high Pt loadings. However, the analysis indicates that truly meaningful advances will likely necessitate the discovery of alternative ORR catalysts. [ABSTRACT FROM AUTHOR]

To alleviate the problems of environmental pollution and energy crisis, aggressive development of clean and alternative energy technologies, in particular, water splitting, metal–air batteries, and fuel cells involving two key half reactions comprising hydrogen evolution reaction (HER) and oxygen reduction (ORR), is crucial. In this work, an innovative hybrid comprising heterogeneous Cu/Co bimetallic nanoparticles homogeneously dispersed on a nitrogen-doped carbon layer (Cu/Co/NC) was constructed as a bifunctional electrocatalyst toward HER and ORR via a hydrothermal reaction along with post-solid-phase sintering technique. Thanks to the interfacial coupling and electronic synergism between the Cu and Co bimetallic nanoparticles, the Cu/Co/NC catalyst showed improved catalytic ORR activity with a half-wave potential of 0.865 V and an excellent stability of more than 30 h, even compared to 20 wt% Pt/C. The Cu/Co/NC catalyst also exhibited excellent HER catalytic performance with an overpotential of below 149 mV at 10 mA/cm2 and long-term operation for over 30 h. [ABSTRACT FROM AUTHOR]

Search for a Platinum metal-free catalyst for Proton Exchange Membrane Fuel Cells (PEMFCs) is a concern to scientists as the Pt-catalyzed electrode comprises about 45% of the entire fuel cell stack cost. Due to layered structure, Two-dimensional (2D) MoS2 nanostructured materials have recently drawn attention as effective catalysts for oxygen reduction reaction (ORR). The 1T-phase of MoS2 (1T-MoS2) has higher electronic conductivity than the 2H-phase (2H-MoS2); high surface area 1T-MoS2 can have high electrocatalytic activity towards PEFFCs. Here, we report hydrothermally synthesized 2H-MoS2 and solvothermally synthesized mixed 1T/2H-MoS2 phases as a catalyst for ORR in PEM Fuel Cells. Owing to the high BET-specific surface area, hybrid 1T/2H-MoS2 showed better ORR activity than 2H-MoS2. The limiting current density of the 1T/2H-MoS2 hybrid structure is ‒7.1 mA cm−2 compared to Pt/C (‒8.2 mA cm−2) at 1600 rpm. The Tafel slope values of 2H-MoS2, 1T/2H-MoS2, and Pt/C are 92.7 mV dec−1, 57.5 mV dec−1, and 39.3 mV dec−1, respectively. The electron transferred during ORR are 3.8 and 1.8, respectively, for 1T/2H-MoS2 and 2H-MoS2 (in 0.1 M KOH) ; suggesting less formation of undesirable peroxide formation than 2H-MoS2. The 1T/2H-MoS2 displays better electrochemical durability compared to 2H-MoS2 (after 2000 CV cycles). [ABSTRACT FROM AUTHOR]

[Display omitted] • A carboxylate linker strategy is proposed to construct atomically dispersed catalyst. • The OAc linker enhances the site density of accessible Fe-N 4 sites in Fe N C OAc. • The Fe N C OAc catalyst shows superior performance in both acidic and alkaline media. • Excellent performance are obtained in both liquid and solid-state Zn-air batteries. Iron-nitrogen-carbon single-atom catalysts derived from zeolitic-imidazolate-framework-8 (ZIF-8) have presented its great potential for the oxygen reduction reaction (ORR) in Zn-air batteries (ZABs). However, due to insufficient active Fe-N sites, its ORR activity is inferior to Pt-based catalysts. Herein, a carboxylate (OAc) linker strategy is proposed to design a ZIF-8-derived Fe N C OAc catalyst with abundant accessible Fe-N 4 single-atom sites. Except that imidazole groups can coordinate with Fe ions, the OAc linker on the unsaturated coordination Zn nodes can anchor and coordinate with more Fe ions, resulting in a significant increase in Fe-N 4 site density. Meanwhile, the corrosion of carbon skeleton by OAc oxidation during heat-treatment leads to improved porosity of catalyst. Benefitting from the highly dense Fe-N 4 sites and hierarchical pores, the Fe N C OAc endows superior performance in alkaline medium (E 1/2 = 0.906 V), which is confirmed by density functional theory calculation results. Meanwhile, the assembled liquid ZAB delivers a favorable peak power density of 173.9 mW cm−2, and a high specific capacity of 770.9 mAh g−1 as well as outstanding durability. Besides, the solid-state ZAB also shows outstanding discharge performance. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Electrochemistry is the property of Journal of Electrochemistry Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Fe-N-C (iron-nitrogen-carbon) electrocatalysts have emerged as potential alternatives to precious metal-based materials for the oxygen reduction reaction (ORR). However, the structure of these materials under electrochemical conditions is not well understood, and their poor stability in acidic environments poses a formidable challenge for successful adoption in commercial fuel cells. To provide molecular-level insights into these complex phenomena, we combine periodic density functional theory (DFT) calculations, exhaustive treatment of coadsorption effects for ORR reaction intermediates, including O and OH, and comprehensive analysis of solvation stabilization effects to construct voltage-dependent ab initio thermodynamic phase diagrams that describe the in situ structure of the active sites. These structures are further linked to activity and stability descriptors that can be compared with experimental parameters such as the half-wave potential for ORR and the onset potential for carbon corrosion and CO2 evolution. The results indicate that pyridinic Fe sites at zigzag carbon edges, as well as other edge sites, exhibit high activity for ORR compared to sites in the bulk. However, edges neighboring the active sites are prone to instability via overoxidation and consequent site loss. The results suggest that it could be beneficial to synthesize Fe-N-C catalysts with small sizes and large perimeter edge lengths to enhance ORR activity, while voltage fluctuations should be limited during fuel cell operation to prevent carbon corrosion of overoxidized edges.

Abstract Non-precious electrocatalysts as the alternative to Pt have become a hot research area in the last decade due to the suitable catalytic activity in Oxygen reduction reaction (ORR) in electrochemical systems. In this work, the density functional theory calculations were investigated to explore the activity of Fe, Cu, and Fe-Cu atoms supported by N-doped graphene as the ORR electrocatalyst for Oxygen-depolarized cathodes (ODCs). To this end, the ORR mechanism was surveyed in detail in the gas and solvent phases. The results show that the solvent phase leads to a higher overpotential and thermodynamic limiting potential. According to the density of states curves, there are strong interactions between metal atom and substrate that can effectively tune the electronics of catalysts. Bader's analysis confirms that, in addition to the single metal atoms, nitrogen atoms have also played a critical role in charge transfer between substrates and oxygen molecules in ORR. It is also predicted that Fe-Cu@NC SAC exhibits the highest catalytic activity which is consistent with thermodynamic limiting potential and theoretical overpotential of − 0.26 and 0.66 (V vs. SHE), respectively, indicating that this type of catalyst may be a suitable candidate instead of precious metals in oxygen-depolarized cathodes in electrochemical devices.

Aiming at the high cost and poor effect of catalytic materials for cathodic oxygen reduction reaction(ORR) in electrochemical deoxygenation, NiCoFe ternary alloy was efficiently prepared by electrodeposition under different current densities, and the morphology and structure of the alloy material were characterized and analyzed, which showed that NiCoFe alloy had a fluffy cauliflower-like surface morphology and alloy crystalline structure. The ORR performance of the NiCoFe alloy was tested in a three-electrode system at different current densities. When the electrodeposition current density was 1.0 A/cm2, the alloy was obtained with a half-wave potential of 0.782 V, an onset potential of 0.936 V, and a limiting current density of 2.9 mA/cm2. The rotating ring disk electrode(RRDE) test showed that the number of transferred electrons of the alloy was 3.52, which was close to that of the four-electron transfer of commercial Pt/C catalysts. An electrochemical deoxidation test equipment was designed to investigate the removal effect of NiCoFe alloy as a cathode electrode on dissolved oxygen in simulated industrial water. The results showed that the deoxidation rate of NiCoFe cathode was over 99%, making it an excellent ORR electrocatalyst material.

Abstract Covalent organic frameworks (COFs) have been utilized as the ideal candidates to preciously construct electrocatalysts. However, the highly ordered degree of COFs renders the catalytic centers closely stacked, which limits the utilization efficiency of catalytic sites. Herein, we have first constructed dangling and staggered‐stacking aldehyde (–CHO) from [4 + 3] COFs as catalytic centers for 2e− oxygen reduction reaction (ORR). The new catalytic COFs have unreacted dangling ‐CHO out of the COFs' planes, which are more easily exposed in electrolytes than the sites in the frameworks. More importantly, these –CHO adopt staggered stacking models, and thus provide larger space for mass transport than those with eclipsed stacking models. In addition, by tuning the triratopic linkers in the COFs, the catalytic properties are well modulated. The optimized COF shows high selectivity and activity for 2e− ORR, with H2O2 selectivity of 91%, and mass activity of 12.2 A g−1, respectively. The theoretical calculation further reveals the higher activity for the pyridine‐contained B18C6‐PTTA‐COF due to the promoted binding ability of the intermediate OOH* at the carbon in dangling –CHO. This work provides us with a new insight into designing electrocatalysts based on COFs.

Highlights A novel A/B-sites co-substitution strategy was introduced to enhance the performance and durability of Ruddlesden–Popper perovskite Sr3Fe2O7−δ (SF)-based air electrodes for reversible protonic ceramic cells (RePCCs). Simultaneous Sr-deficiency and Nb-substitution in SF result in Sr2.8Fe1.8Nb0.2O7−δ (D-SFN), offering improved structural stability under RePCC conditions by suppressing the formation of Sr3Fe2(OH)12 phase. The introduction of Sr-deficiency enhances oxygen vacancy concentration in D-SFN, promoting efficient oxygen transport within the material and contributing to excellent activity in RePCCs.

Oxygen reduction reaction (ORR) and oxygen evolutionc reaction (OER) are important chemical reactions for a rechargeable lithium–oxygen battery (LOB). Recently, high-entropy alloys and oxides have attracted much attention because they showed good electrocatalytic performance for oxygen evolution reaction (OER) and/or oxygen reduction reaction (ORR). In this study, we aimed to synthesize and characterize CoSn(OH)6 and two types of high-entropy perovskite hydroxides, that is, (Co0.2Cu0.2Fe0.2Mn0.2Mg0.2)Sn(OH)6 (CCFMMSOH) and (Co0.2Cu0.2Fe0.2Mn0.2Ni0.2)Sn(OH)6 (CCFMNSOH). TEM observation and XRD measurements revealed that the high-entropy hydroxides CCFMMSOH and CCFMNSOH had cubic crystals with sides of approximately 150–200 nm and crystal structures similar to those of perovskite-type CSOH. LSV measurement results showed that the high-entropy hydroxides CCFMMSOH and CCFMNSOH showed bifunctional catalytic functions for the ORR and OER. CCFMNSOH showed better catalytic performance than CCFMMSOH. [ABSTRACT FROM AUTHOR]

The sluggish kinetics of oxygen reduction reactions (ORRs) require considerable Pd in the cathode, hindering the widespread of alkaline fuel cells (AFCs). By alloying Pd with transition metals, the oxygen reduction reaction's catalytic properties can be substantially enhanced. Nevertheless, the utilization of Pd-transition metal alloys in fuel cells is significantly constrained by their inadequate long-term durability due to the propensity of transition metals to leach. In this study, a nonmetallic doping strategy was devised and implemented to produce a Pd catalyst doped with P that exhibited exceptional durability towards ORRs. Pd3P0.95 with an average size of 6.41 nm was synthesized by the heat-treatment phosphorization of Pd nanoparticles followed by acid etching. After P-doping, the size of the Pd nanoparticles increased from 5.37 nm to 6.41 nm, and the initial mass activity (MA) of Pd3P0.95/NC reached 0.175 A mgPd−1 at 0.9 V, slightly lower than that of Pd/C. However, after 40,000 cycles of accelerated durability testing, instead of decreasing, the MA of Pd3P0.95/NC increased by 6.3% while the MA loss of Pd/C was 38.3%. The durability was primarily ascribed to the electronic structure effect and the aggregation resistance of the Pd nanoparticles. This research also establishes a foundation for the development of Pd-based ORR catalysts and offers a direction for the future advancement of catalysts designed for practical applications in AFCs. [ABSTRACT FROM AUTHOR]

We explored two methods for synthesizing Pd nanoparticles using three different carbide-derived carbon (CDC) support materials, one of which was nitrogen-doped. These materials were studied for oxygen reduction reaction (ORR) in 0.1 M KOH solution, and the resulting CDC/Pd catalysts were characterized using TEM, XRD, and XPS. The citrate method and the polyol method using polyvinylpyrrolidone (PVP) as a capping agent were employed to elucidate the impact of the support material on the final catalyst. The N-doping of the CDC material resulted in smaller Pd nanoparticles, but only in the case of the citrate method. This suggests that the influence of support is weaker when using the polyol method. The citrate method with CDC1, which is predominantly microporous, led to a higher degree of agglomeration and formation of larger particles in comparison to supports, which possessed a higher degree of mesoporosity. We achieved smaller Pd particle sizes using citrate and NaBH4 compared to the ethylene glycol PVP method. Pd deposited on CDC2 and CDC3 supports showed similar specific activity (SA), suggesting that the N-doping did not significantly influence the ORR process. The highest SA value was observed for CDC1/Pd_Cit, which could be attributed to the formation of larger Pd particles and agglomerates. [ABSTRACT FROM AUTHOR]

[Display omitted] Oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are essential for the development of excellent bifunctional electrocatalysts, which are key functions in clean energy production. The emphasis of this study lies in the rapid design and investigation of 153 MN 4 –graphene (Gra)/ MXene (M 2 NO) electrocatalysts for ORR/OER catalytic activity using machine learning (ML) and density functional theory (DFT). The DFT results indicated that CoN 4 –Gra/Ti 2 NO had both good ORR (0.37 V) and OER (0.30 V) overpotentials, while TiN 4 –Gra/M 2 NO and MN 4 –Gra/Cr 2 NO had high overpotentials. Our research further indicated orbital spin polarization and d-band centers far from the Fermi energy level, affecting the adsorption energy of oxygen-containing intermediates and thus reducing the catalytic activity. The ML results showed that the gradient boosting regression (GBR) model successfully predicted the overpotentials of the monofunctional catalysts RhN 4 –Gra/Ti 2 NO (ORR, 0.39 V) and RuN 4 –Gra/W 2 NO (OER, 0.45 V) as well as the overpotentials of the bifunctional catalyst RuN 4 –Gra/W 2 NO (ORR, 0.39 V; OER, 0.45 V). The symbolic regression (SR) algorithm was used to construct the overpotential descriptors without environmental variable features to accelerate the catalyst screening and shorten the trial-and-error costs from the source, providing a reliable theoretical basis for the experimental synthesis of MXene heterostructures. [ABSTRACT FROM AUTHOR]

[Display omitted] Lignin upgrading to various functional products is promising to realize high-value utilization of low-cost and renewable biomass waste, but is still in its infancy. Herein, using industry waste lignosulfonate as the biomass-based carbon source and urea as the dopant, we constructed a heteroatom-doped porous carbon nanosheet structure by a simple NaCl template-assisted pyrolytic strategy. Through the synergistic effect of the NaCl template and urea, the optimized lignin-derived porous carbon catalyst with high content of active nitrogen species and large specific surface area can be obtained. As a result, the fabricated catalysts exhibited excellent electrocatalytic oxygen reduction activity, as well as good methanol tolerance and stability, comparable to that of commercial Pt/C. Moreover, rechargeable Zn-air batteries assembled with this electrocatalyst have a peak power density of up to 150 mW cm-2 and prominent long-term cycling stability. This study offers an inexpensive and efficient way for the massive production of highly active metal-free catalysts from the plentiful, inexpensive and environmentally friendly lignin, offering a good direction for biomass waste recycling and utilization. [ABSTRACT FROM AUTHOR]

[Display omitted] • 2D GnP/MoS 2 and 3D (GnP/MoS 2)/MWNT composites are prepared by a facile, robust and ecofriendly method. • Effects of N-doping of GnPs and mass fraction of MWNTs on ORR activity are explored and rationalized. • Best synergistic ORR activity is obtained for N-doped catalyst with 3:1 2D-to-1D ratio. • Catalysts exhibit excellent stability and methanol resistance in alkaline medium. • Promising route to develop bifunctional ORR/OER catalysts. Nanocomposites have garnered attention for their potential as catalysts in electrochemical reactions vital for technologies like fuel cells, water splitting, and metal-air batteries. This work focuses on developing three-dimensional (3D) nanocomposites through aqueous phase exfoliation, non-covalent functionalization of building blocks with surfactants and polymers, and electrostatic interactions in solution leading to the nanocomposites assembly and organization. By combining molybdenum disulfide (MoS 2) layers with graphene nanoplatelets (GnPs) to form a binary 2D composite (MoS 2 /GnP), and subsequently incorporating multiwalled carbon nanotubes (MWNTs) to create ternary 3D composites, we explore their potential as catalysts for the oxygen reduction reaction (ORR) critical in fuel cells. Characterization techniques such as X-ray photoelectron spectroscopy, scanning electron microscopy, and X-ray diffraction elucidate material composition and structure. Our electrochemical studies reveal insights into the kinetics of the reactions and structure–activity relationships. Both the (MoS 2 /GnP)-to-MWNT mass ratio and nitrogen-doping of GnPs (N -GnPs) play a key role on the electrocatalytic ORR performance. Notably, the (MoS 2 / N -GnP)/MWNT material, with a 3:1 mass ratio, exhibits the most effective ORR activity. All catalysts demonstrate good long-term stability and methanol crossover tolerance. This facile fabrication method and observed trends offer avenues for optimizing composite electrocatalysts further. [ABSTRACT FROM AUTHOR]

In this study, Co/Ni‐NC catalyst with hetero‐diatomic Co/Ni active sites dispersed on nitrogen‐doped carbon matrix is synthesized via the controlled pyrolysis of ZIF‐8 containing Co2+ and Ni2+ compounds. Experimental characterizations and theoretical calculations reveal that Co and Ni are atomically and uniformly dispersed in pairs of CoN4‐NiN4 with an intersite distance ≈0.41 nm, and there is long‐range d–d coupling between Co and Ni with more electron delocalization for higher bifunctional activity. Besides, the in situ grown carbon nanotubes at the edges of the catalyst particles allow high electronic conductivity for electrocatalysis process. Electrochemical evaluations demonstrate the superior ORR and OER bifunctionality of Co/Ni‐NC catalyst with a narrow potential gap of only 0.691 V and long‐term durability, significantly prevailing over the single‐atom Co‐NC and Ni‐NC catalysts and the benchmark Pt/C and RuO2 catalysts. Co/Ni‐NC catalyzed Zn–air batteries achieve a high specific capacity of 771 mAh g−1 and a long continuous operation period up to 340 h with a small voltage gap of ≈0.65 V, also much superior to Pt/C‐RuO2. [ABSTRACT FROM AUTHOR]

The shortage and unevenness of fossil energy sources are affecting the development and progress of human civilization. The technology of efficiently converting material resources into energy for utilization and storage is attracting the attention of researchers. Environmentally friendly biomass materials are a treasure to drive the development of new‐generation energy sources. Electrochemical theory is used to efficiently convert the chemical energy of chemical substances into electrical energy. In recent years, significant progress has been made in the development of green and economical electrocatalysts for oxygen reduction reaction (ORR). Although many reviews have been reported around the application of biomass‐derived catalytically active carbon (CAC) catalysts in ORR, these reviews have only selected a single/partial topic (including synthesis and preparation of catalysts from different sources, structural optimization, or performance enhancement methods based on CAC catalysts, and application of biomass‐derived CACs) for discussion. There is no review that systematically addresses the latest progress in the synthesis, performance enhancement, and applications related to biomass‐derived CAC‐based oxygen reduction electrocatalysts synchronously. This review fills the gap by providing a timely and comprehensive review and summary from the following sections: the exposition of the basic catalytic principles of ORR, the summary of the chemical composition and structural properties of various types of biomass, the analysis of traditional and the latest popular biomass‐derived CAC synthesis methods and optimization strategies, and the summary of the practical applications of biomass‐derived CAC‐based oxidative reduction electrocatalysts. This review provides a comprehensive summary of the latest advances to provide research directions and design ideas for the development of catalyst synthesis/optimization and contributes to the industrialization of biomass‐derived CAC electrocatalysis and electric energy storage. [ABSTRACT FROM AUTHOR]

The development of low-cost, high-performance oxygen electrocatalysts is of great significance for energy conversion and storage. As a potential substitute for precious metal electrocatalysts, the construction of efficient and cost-effective oxygen electrocatalysts is conducive to promoting the widespread application of zinc–air batteries. Herein, CoxNiyMOF nanoparticles encapsulated within a carbon matrix were synthesized and employed as cathode catalysts in zinc–air batteries. Co0.5Ni0.5MOF exhibits superior oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) performance and durability. The zinc–air battery assembled with Co0.5Ni0.5MOF as the air cathode exhibits a maximum power density of 138.6 mW·cm−2. These improvements are mainly attributed to the optimized metal composition of the cobalt–nickel alloy, which increases the specific surface area of the material and optimizes its pore structure. Significantly, the optimization of the electronic structure and active sites within the material has led to amplified ORR/OER activity and better zinc–air battery performance. This study underscores the immense promise of Co0.5Ni0.5MOF catalysts as feasible substitutes for commercial Pt/C catalysts in zinc–air batteries. [ABSTRACT FROM AUTHOR]

Polymer electrolyte membrane fuel cells (PEMFCs) have attracted much attention as highly efficient, eco-friendly energy conversion devices. However, carbon-supported Pt (Pt/C) catalysts for PEMFCs still have several problems, such as low long-term stability, to be widely commercialized in fuel cell applications. To address the stability issues of Pt/C such as the dissolution, detachment, and agglomeration of Pt nanoparticles under harsh operating conditions, we design an interesting fabrication process to produce a highly active and durable Pt catalyst by introducing a robust carbon shell on the Pt surface. Furthermore, this approach provides insights into how to regulate the carbon shell layer for fuel cell applications. Through the application of an appropriate amount of H2 gas during heat treatment, the carbon shell pores, which are integral to the structure, can be systematically modulated to facilitate oxygen adsorption for the oxygen reduction reaction. Simultaneously, the carbon shell functions as a protective barrier, preventing catalyst degradation. In this regard, we investigate an in-depth analysis of the effects of critical parameters including H2 content and the flow rate of H2/N2 mixed gas during heat treatment to prepare better catalysts. [ABSTRACT FROM AUTHOR]

Ionic liquid modification for carbon-supported platinum (Pt/C) electrocatalysts to enhance their oxygen reduction reaction (ORR) activity has been well recognized. However, the research has only been reported on the low-Pt-loading Pt/C electrocatalysts, e.g., 20 wt%, while in practical applications, usually high-Pt-loading Pt/C electrocatalysts of 45–60 wt% are used. In this work, ionic liquid modification is systematically investigated for a Pt/C electrocatalyst with 60 wt% Pt loading for its ORR activity in the cathode in proton exchange membrane fuel cells (PEMFCs). Various adsorption amounts are studied on the catalyst surface. Different modification behavior is found. Mechanism exploration shows that the adsorption of ionic liquid mainly happens on the Pt electrocatalyst surface and in the micropores of the carbon support. The highest fuel cell power performance is achieved at an ionic liquid loading of 7 wt%, which is much higher than the 3 wt% reported for the low-Pt-loading Pt/C. [ABSTRACT FROM AUTHOR]

[Display omitted] Fe N C single atom catalysts (SACs) have attracted great interest due to their highly active FeN 4 sites. However, the pyrolysis treatment often leads to inevitable metal migration and aggregation, which reduces the catalytic activity. Moreover, due to the Fenton reaction caused by Fe N C in alkaline and acidic solutions, the presence of Fe and peroxide in electrodes may generate free radicals, resulting in serious degradation of the organic ionomer and the membrane. Herein, we report an original strategy of introducing Co single atoms into Fe N C catalysts, forming atomically dispersed bimetallic active sites (Fe Co NC) and improving the activity and stability of the catalyst. Benefiting from this strategy, Fe Co NC catalyst exhibits excellent oxygen reduction reaction (ORR) activity in alkaline media (E 1/2 = 0.88 V) and in acidic media (E 1/2 = 0.77 V). As the cathode of Zn-air battery (ZAB), Fe Co NC shows an excellent peak power density of 142.8 mW cm−2 and a specific capacity of 806.6 mAh/g Zn. This work provides a novel avenue to optimize and enhance the ORR performance of atomic dispersed Fe N C catalysts. [ABSTRACT FROM AUTHOR]

Trillion of cigarette butts are annually littered without being recycled. This work aims at valorizing the whole cigarette butts and their components (paper, filter and tobacco) into Fe‐Nx‐C electrocatalysts for oxygen reduction reaction (ORR) in acid and alkaline media. The pristine wastes were pyrolyzed at 450 °C, activated with KOH at 700 °C, blended with iron phthalocyanine (FePc) precursor, and heat‐treated at 600 °C to produce a robust Fe‐Nx‐C material with ORR active units. The effect of the cigarette components on the final electrocatalytic activity was evaluated by thoroughly investigating the surface chemistry with XPS. The electrocatalysts displayed similar results among the different components in both media due to comparable surface chemistry, especially concerning the nitrogen functional groups. The highest performance was obtained in alkaline where the electrocatalysts from whole cigarettes and paper (CIGF_450 and CIGPF_450) showed an E1/2 of 0.89 V vs RHE, slightly larger than that of Pt/C with 40 wt % of Pt, which encouraged to replace Pt‐based electrocatalysts in alkaline fuel cells. [ABSTRACT FROM AUTHOR]

Copyright of Industrial Water Treatment is the property of CNOOC Tianjin Chemical Research & Design Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Glucose-derived carbon hybrids were synthesized by hydrothermal treatment in the presence of oxidized carbon nanotubes. Additionally, iron and nitrogen functionalities were incorporated into the carbon structure using different methodologies. The introduction of iron and nitrogen in a single step under a H2 atmosphere favored the formation of quaternary nitrogen and oxidized nitrogen, whereas the incorporation of nitrogen under an N2 atmosphere after doping the hybrids with iron mainly produced pyridinic nitrogen. The samples were characterized by scanning electron microscopy, X-ray spectroscopy, adsorption isotherms, inductively coupled plasma optical emission spectrometry, and Raman spectroscopy. The presence of iron and nitrogen in the carbons increases the onset potential toward oxygen reduction in KOH 0.1 mol L−1 by 130 mV (0.83 V), in comparison to carbonized glucose, whereas the reaction mechanism shifts closer to a direct pathway and the formation of HO2− decreases to 25% (3.5 electrons). The reaction rate also increased in comparison to the carbonized glucose, as observed by the decrease in the Tafel slope value from 117 to 61 mV dec−1. Furthermore, the incorporation of iron and nitrogen in a single step enhanced the short-term performance of the prepared electrocatalysts, which may also be due to the higher relative amount of quaternary nitrogen. [ABSTRACT FROM AUTHOR]

Understanding the electrode materials' surface is of fundamental importance for catalytic studies as most electrochemical reactions take place there. Although several operando techniques have been used to monitor the electrocatalytic process, real‐time imaging techniques for observing the surface change on electrode materials are still a challenge and limited to a few stable catalytic systems. Herein, the quasi‐in situ electrochemical transmission electron microscopy (TEM) was carried out to track the morphological and local structure evolution during the oxygen reduction reaction (ORR) on manganese dioxide (MnO2) for the first time. The α‐MnO2 nanorods exhibit comparable ORR electrocatalytic activity (half‐wave potential, E1/2: 0.83 vs. 0.85 V vs. RHE; diffusion‐limiting current density, Jd: −5.46 vs. −5.52 mA cm−2) and better methanol tolerance than Pt/C. An electrochemical TEM chip assembled with a three‐electrode system was used to perform the electrochemical experiments similar to typical testing procedures. The ex situ and quasi‐in situ TEM images consistently showed that MnO2 nanorods had undergone surface roughening, and lattice expansion with 0.97% and 1.97% in the a and c‐axis, respectively as ORR proceeded. The quasi‐in situ electrochemical TEM fills the gap between ex situ characterization and operando spectroscopies and deepens the mechanistic understanding of electrocatalytic processes. [ABSTRACT FROM AUTHOR]

Polyoxometalates (POMs) with transition metals (Co, Cu, Fe, Mn, Ni) of Keggin structure and lamellar-stacked multi-layer morphology were synthesized. They were subsequently explored as bifunctional electrocatalysts for oxygen electrodes, i.e., oxygen reduction (ORR) and evolution (OER) reaction, for aqueous rechargeable metal-air batteries in alkaline media. The lowest Tafel slope (85 mV dec−1) value and the highest OER current density of 93.8 mA cm−2 were obtained for the Fe-POM electrocatalyst. Similar OER electrochemical catalytic activity was noticed for the Co-POM electrocatalyst. This behavior was confirmed by electrochemical impedance spectroscopy, where Fe-POM gave the lowest charge transfer resistance of 3.35 Ω, followed by Co-POM with Rct of 15.04 Ω, during the OER. Additionally, Tafel slope values of 85 and 109 mV dec−1 were calculated for Fe-POM and Co-POM, respectively, during the ORR. The ORR at Fe-POM proceeded by mixed two- and four-electron pathways, while ORR at Co-POM proceeded exclusively by the four-electron pathway. Finally, capacitance studies were conducted on the synthesized POMs. [ABSTRACT FROM AUTHOR]

This work summarizes the disciplinary connotation of ecological aesthetics, discusses the social and philosophical background of the origination of ecological aesthetics, and applies ecological aesthetics to the research on the production processes of catalytic materials. It is found that compared with conventional chemical processes, catalytic materials synthesized using green chemical processes that conform to ecological aesthetics have advantages in raw material cost, energy consumption, environmental protection, operational complexity, and product performance. Based on this, it is proposed that, as green chemical processes develop to a certain extent, they will unify anthropocentrism and ecocentrism, and meet both human needs and ecological protection requirements. The mentioned green chemical processes adopt biomass lotus leaf stems as a carbon source to produce non-noble metal bimetallic carbide (C19Cr7Mo24)-based catalysts for oxygen reduction reaction (ORR). Its initial half-wave potential (E1/2) for catalyzing ORR in an alkaline medium is 0.903 V, the E1/2 retention rate after 50,000 cycles is 98.9%, and its peak power density in H2/O2 fuel cell reaches 1.47 W cm−2, making it one of the most active non-noble metal catalysts for ORR reported so far; its stability is unparalleled. [ABSTRACT FROM AUTHOR]

Climate change is showing its impacts now more than ever. The intense use of fossil fuels and the resulting CO2 emissions are mainly to blame, accentuating the need to develop further the available energy conversion and storage technologies, which are regarded as effective solutions to maximize the use of intermittent renewable energy sources and reduce global CO2 emissions. This work comprehensively overviews the most recent progress and trends in the use of transition metal-based electrocatalysts for three crucial reactions in electrochemical energy conversion and storage, namely, the oxygen evolution (OER), oxygen reduction (ORR), and hydrogen evolution (HER) reactions. By analyzing the state-of-the-art polyoxometalates (POMs) and metal-organic frameworks (MOFs), the performance of these two promising types of materials for OER, ORR, and HER is compared to that of more traditional transition metal oxides and alloy-based electrocatalysts. Both catalytic activity and stability are highly influenced by the adsorption energies of the intermediate species formed in each reaction, which are very sensitive to changes in the microstructure and chemical microenvironment. POMs and MOFs allow these aspects to be easily modified to fine-tune the catalytic performances. Therefore, their chemical tunability and versatility make it possible to tailor such properties to obtain higher electrocatalytic activities, or even to obtain derived materials with more compelling properties towards these reactions. [ABSTRACT FROM AUTHOR]

A Fe-Co dual-metal co-doped N containing the carbon composite (FeCo-HNC) was prepared by adjusting the ratio of iron to cobalt as well as the pyrolysis temperature with the assistance of functionalized silica template. Fe1Co-HNC, which was formed with 1D carbon nanotubes and 2D carbon nanosheets including a rich mesoporous structure, exhibited outstanding oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalytic activities. The ORR half-wave potential is 0.86 V (vs. reversible hydrogen electrode, RHE), and the OER overpotential is 0.76 V at 10 mA cm−2 with the Fe1Co-HNC catalyst. It also displayed superior performance in zinc–air batteries. This method provides a promising strategy for the fabrication of efficient transition metal-based carbon catalysts. [ABSTRACT FROM AUTHOR]

Electrochemical oxygen reduction reaction (ORR) via the 2e− pathway in an acidic media shows great techno-economic potential for the production of hydrogen peroxide. Currently, carbon-based single-atom catalysts (C-SACs) have attracted extensive attention due to their tunable electronic structures, low cost, and sufficient stability in acidic media. This review summarizes recent advances in metal centers and their coordination environment in C-SACs for 2e−-ORR. Firstly, the reaction mechanism of 2e−-ORR on the active sites of C-SACs is systematically presented. Secondly, the structural regulation strategies for the active sites of 2e−-ORR are further summarized, including the metal active center, its species and configurations of nitrogen coordination or heteroatom coordination, and their near functional groups or substitute groups, which would provide available and proper ideas for developing superior acidic 2e−-ORR electrocatalysts of C-SACs. Finally, we propose the current challenges and future opportunities regarding the acidic 2e−-ORR pathway on C-SACs, which will eventually accelerate the development of the distributed H2O2 electrosynthesis process. [ABSTRACT FROM AUTHOR]

[Display omitted] The zinc-air battery (ZAB) performance and stability strongly depend on the structure of bifunctional electrocatalyst for oxygen reduction/evolution reaction (ORR/OER). In this work, we combine the tip and heterogeneous effects to construct cobalt/cobalt oxide heterostructure nanoarrays (Co/CoO-NAs). Due to the formed heterostructure, more oxygen vacancies are found for Co/CoO-NAs resulting in a 1.4-fold higher ORR intrinsic activity than commercial carbon supported platinum electrocatalyst (Pt/C) at 0.8 V versus reversible hydrogen electrode (vs. RHE). Moreover, a fast surface reconstruction is observed for Co/CoO-NAs during OER catalysis evidenced by in-situ electrochemical impedance spectroscopy and Raman tests. In addition, the tip effect efficiently lowers the mass transfer resistance triggering a low overpotential of 347 mV at 200 mA cm−2 for Co/CoO-NAs. The strong electronic interplay between cobalt (Co) and cobalt oxide (CoO) contributes to a stable battery performance during 1200 h galvanostatic charge–discharge test at 5 mA cm−2. This work offers a new avenue to construct high-performance and stable oxygen electrocatalyst for rechargeable ZAB. [ABSTRACT FROM AUTHOR]

[Display omitted] • The FeCoNiMnV HEA/ N -CNTs catalyst was prepared by a one-step pyrolysis. • The multi-metal synergy favored the ORR catalytic performance. • Clustered N -CNTs had rich shared boundaries and interstitial space to expedite the charge/mass transfer. • The built battery showed high OCV, large power density and long-term durability. Efficient and stable oxygen reduction reaction (ORR) catalysts are essential for constructing reliable energy conversion and storage devices. Herein, we prepared noble metal-free FeCoNiMnV high-entropy alloy supported on nitrogen-doped carbon nanotubes (FeCoNiMnV HEA/ N -CNTs) by a one-step pyrolysis at 800 °C, as certificated by a set of characterizations. The graphitization degree of the N -CHTs was optimized by tuning the pyrolysis temperature in the control groups. The resultant catalyst greatly enhanced the ORR characteristics in the alkaline media, showing the positive onset potential (E onset) of 0.99 V and half-wave potential (E 1/2) of 0.85 V. More importantly, the above FeCoNiMnV HEA/ N -CNTs assembled Zn-air battery exhibited a greater open-circuit voltage (1.482 V), larger power density (185.12 mW cm−2), and outstanding cycle stability (1698 cycles, 566 h). This study provides some valuable insights on developing sustainable ORR catalysts in Zn-air batteries. [ABSTRACT FROM AUTHOR]