Search

This paper presents a gravimetric method for the quantification of total organic carbon by ignition at 1100°C and carbonates by acid dissolution in rock samples containing coal. Two minerals (CM-1 and CM-2) and a subbituminous coal (SBC) were used in the study. The mineralogical characterization of the samples was performed by X-ray diffraction and scanning electron microscopy. This revealed the presence of calcite in samples CM-1 (20.4%) and CM-2 (74.7%), dolomite in CM-2 (0.7%), and graphite in sample SBC (42.6%). To eliminate carbonates, the samples were treated with 4 mol/L HCl, which allowed quantification. Results of the carbonate gravimetric quantification were compared with those obtained with a calcimeter. A significant difference was observed for the sample CM-2 (70.3% versus 63.4% by calcimetry, p-value = 0.0042). For the sample without carbonates, no differences were observed for loss on ignition without and with the acid treatment, so this is not necessary for this type of sample. A morphological study showed no significant surface change after acid treatment, but fracture of iron oxide particles was observed in CM-1 and CM-2 after heat treatment. In this study it was demonstrated that rock mineralogy is essential to correctly analyze organic and inorganic carbon content. [ABSTRACT FROM AUTHOR]

The Lower Ordovician Tongzi Formation containing abundant shoal sediments is the most promising stratum for the petroleum exploration in the Sichuan Basin. However, the current studies mainly focus on the central part of the Basin, the systematic analysis of the southeastern part with well-developed shoal facies is lacking. This paper aims to clarify the characteristics and genesis of the Tongzi Formation reservoir in Southeastern Sichuan Basin, following an analysis of sedimentary facies within the sequence stratigraphic framework. The research shows that the main types of reservoir rocks are oolitic, intraclastic and bioclastic dolostones. And the reservoir spaces consist mainly of intergranular (dissolved) pores, inter-crystalline (dissolved) pores, intragranular dissolved pores and fractures. Among them, intergranular pores account for the highest proportion, which is followed by intragranular dissolved pores. In addition, most throats are necking and flaky which mainly connect intergranular and inter-crystalline pores, respectively. The diagenetic sequence shows that penecontemporaneous karst well improved the porosity of the reservoir in the early-stage although the cementation and compaction reduced parts of pores. The reservoir formation is associated with the tectonic-depositional settings, diageneses and terrigenous contamination. Paleohighlands and submerged uplifts, forming in the early Ordovician amalgamation between Yangtze and Cathaysia blocks, accumulated shoal sediments as the material basis for the reservoir formation. Penecontemporaneous karst forming intragranular dissolved pores and the dolomitization aiding grainstones to resist the pressure solution are the key to increasing porosity and preserving pores. The absence of terrigenous contamination prevented intergranular pores from being strongly cemented, which resulted in the reservoir difference between the central and southeastern Sichuan Basin. The study can be used as a reference for the further exploration of Ordovician petroleum in the Sichuan Basin and other regions owning similar geological settings. [ABSTRACT FROM AUTHOR]

The marine carbonates in the Ordovician Majiagou Formation in the Ordos Basin have significant exploration potential. Research has focused on their thermal history and hydrocarbon accumulation stages, as these are essential for guiding the exploration and development of hydrocarbons. In this paper, we study the thermal evolution history of the carbonate reservoirs of the Ordovician Majiagou Formation in the east-central Ordos Basin. Furthermore, petrographic and homogenization temperature studies of fluid inclusions were carried out to further reveal the hydrocarbon accumulation stages. The results demonstrate that the degree of thermal evolution of the Ordovician carbonate reservoirs is predominantly influenced by the deep thermal structure, exhibiting a trend of high to low values from south to north in the central region of the basin. The Fuxian area is located in the center of the Early Cretaceous thermal anomalies, with the maturity degree of the organic matter ranging from 1 to 3.2%, with a maximum value of 3.2%. The present geothermal gradient of the Ordovician Formation exhibits the characteristics of east–high and west–low, with an average of 28.6 °C/km. The average paleo-geotemperature gradient is 54.2 °C/km, the paleoheat flux is 55 mW/m2, and the maximum paleo-geotemperature reaches up to 270 °C. The thermal history recovery indicates that the Ordovician in the central part of the basin underwent three thermal evolution stages: (i) a slow warming stage before the Late Permian; (ii) a rapid warming stage from the end of the Late Permian to the end of the Early Cretaceous; (iii) a cooling stage after the Early Cretaceous, with the hydrocarbon production of hydrocarbon source rocks weakening. In the central part of the basin, the carbonate rock strata of the Majiagou Formation mainly developed asphalt inclusions, natural gas inclusions, and aqueous inclusions. The fluid inclusions can be classified into two stages. The early-stage fluid inclusions are mainly present in dissolution holes. The homogenization temperature is 110–130 °C; this coincides with the hydrocarbon charging period of 210–165 Ma, which corresponds to the end of the Triassic to the end of the Middle Jurassic. The late-stage fluid inclusions are in the dolomite vein or late calcite that filled the gypsum-model pores. The homogenization temperature is 160–170 °C; this coincides with the hydrocarbon charging period of 123–97 Ma, which corresponds to the late Early Cretaceous. Both hydrocarbon charging periods are in the rapid stratigraphic warming stage. [ABSTRACT FROM AUTHOR]

The ash generated by Circulating Fluidized Bed (CFB) boilers is featured by its looseness and porosity, low content of glassy substances, and high contents of calcium (Ca) and sulfur (S), thus resulting in a low comprehensive utilization rate. Currently, the predominant treatment approach for CFB ash and slag is stacking, which may give rise to issues like environmental pollution. In this paper, CFB ash (with a CaO content of 7.64% and an SO3 content of 1.77%) was used as the main raw material. The high-temperature melting characteristics, viscosity–temperature characteristics, and initial crystallization temperature of samples with different acidity coefficients were investigated. The final drawing temperature range of the samples was determined, and mechanical property tests were conducted on the prepared inorganic fibers. The results show that the addition of dolomite powder has a significant reducing effect on the complete liquid phase temperature. The final drawing temperatures of the samples with different acidity coefficients range as follows: 1270–1318 °C; 1272–1351 °C; 1250–1372 °C; 1280–1380 °C; 1300–1382 °C; and 1310–1384 °C. The drawing temperature of this system is slightly lower than that of basalt fibers. Based on the test results of the mechanical properties of inorganic fibers, the Young's modulus of the inorganic fibers prepared through the experiment lies between 55 GPa and 74 GPa, which basically meets the performance requirements of inorganic fibers. Consequently, the method of preparing inorganic fibers by using CFB ash and dolomite powder is entirely feasible. [ABSTRACT FROM AUTHOR]

Reactive transport modeling (RTM) is an emerging method used to address geological issues in diagenesis research. However, the extrapolation of RTM results to practical reservoir prediction is not sufficiently understood. This paper presents a case study of the Eocene Qaidam Basin that combines RTM results with petrological and mineralogical evidence. The results show that the Eocene Xiaganchaigou Formation is characterized by mixed siliciclastic-carbonate-evaporite sedimentation in a semiclosed saline lacustrine environment. Periodic evaporation and salinization processes during the syngeneticpenecontemporaneous stage gave rise to the replacive genesis of dolomites and the cyclic enrichment of dolomite in the middle-upper parts of the meter-scale depositional sequences. The successive change in mineral paragenesis from terrigenous clastics to carbonates to evaporites was reconstructed using RTM simulations. Parametric uncertainty analyses further suggest that the evaporation intensity (brine salinity) and particle size of sediments (reactive surface area) were important rate-determining factors in the dolomitization, as shown by the relatively higher reaction rates under conditions of higher brine salinity and fine-grained sediments. Combining the simulation results with measured mineralogical and reservoir physical property data indicates that the preservation of original intergranular pores and the generation of porosity via replacive dolomitization were the major formation mechanisms of the distinctive lacustrine dolomite reservoirs (widespread submicron intercrystalline micropores) in the Eocene Qaidam Basin. The results confirm that RTM can be effectively used in geological studies, can provide a better general understanding of the dolomitizing fluid-rock interactions, and can shed light on the spatiotemporal evolution of mineralogy and porosity during dolomitization and the formation of lacustrine dolomite reservoirs. [ABSTRACT FROM AUTHOR]

There are concerns that Mg-calcite crustose coralline algae (CCA), which are key reef builders on coral reefs, will be most susceptible to increased rates of dissolution under higher pCO2 and ocean acidification. Due to the higher solubility of Mg-calcite, it has been hypothesized that magnesium concentrations in CCA Mg-calcite will decrease as the ocean acidifies, and that this decrease will make their skeletons more chemically stable. In addition to Mg-calcite, CCA Porolithon onkodes the predominant encrusting species on tropical reefs, can have dolomite (Ca0.5Mg0.5CO3) infilling cell spaces which increases their stability. However, nothing is known about how bio-mineralised dolomite formation responds to higher pCO2. Using P. onkodes grown for 3 and 6 months in tank experiments, we aimed to determine (1) if mol%MgCO3 in new crust and new settlement affected by increasing pCO2 levels (365, 444, 676 and 904 ppm), (2) whether bio-mineralised dolomite formed within these time frames, and (3) if so, whether this was effected by pCO2. Our results show there was no significant effect of pCO2 on mol%MgCO3 in any sample set, indicating an absence of a plastic response under a wide range of experimental conditions. Dolomite within the CCA cells formed within 3 months and dolomite abundance did not vary significantly with pCO2 treatment. While evidence mounts that climate change will impact many sensitive coral and CCA species, the results from this study indicate that reef-building P. onkodes will continue to form stabilising dolomite infill under near-future acidification conditions, thereby re- taining its higher resistance to dissolution. [ABSTRACT FROM AUTHOR]

The Cambrian pre-salt dolomite sequence in the Tarim Basin is a target zone of great strategic significance for hydrocarbon exploration in the basin. Using the results of the interpretation of 3D seismic data from Lunnan and 2D seismic data covering the whole basin, and based on a synthesis of outcrop data, drilling data, well logs, core data, and thin-section data, and the findings from previous studies, this paper studies the characteristics of the facies of the Middle–Lower Cambrian in the platform area in the Tarim Basin, the formation and evolution of platform margins, and the sedimentary characteristics, lithofacies, and paleogeographic characteristics of the Middle–Lower Cambrian series. Based on the types of lithofacies and the seismic facies analysis, the sedimentary facies of the Middle–Lower Cambrian strata can be classified into the five types. From bottom to top, the Middle–Lower Cambrian have experienced several development stages, including the deposition of continental shelf sediments of the Yuertusi Formation, gently sloping non-rimmed platform margin sediments of the Xiaoerbulake Formation, weakly rimmed platform margin sediments of the Wusongger and Shayilike formations, and strongly rimmed platform margin sediments of the Awatage Formation. In each stage, the platform margin shifted further east relative to its location in the previous stage. Based on these results and previous studies, the lithofacies and paleogeography maps of the Middle–Lower Cambrian in the Tarim Basin are modified, and the implications for hydrocarbon exploration in this area are discussed. [ABSTRACT FROM AUTHOR]

Hydraulic fracturing (HF) is the primary choice for stimulating petroleum reservoirs. Rock tensile strength and brittleness are crucial parameters required for screening candidate reservoirs and in designing successful HF operations. However, in situ and laboratory determinations of the hydraulic tensile strength (HTS) of rock can prove problematic. Alternatively, the HTS could be estimated from the rock brittleness once a reliable relationship has been established between them. Accordingly, this paper investigates the correlations between the HTS, as measured using laboratory hydraulic fracture tests, and ten strength-based brittleness indices (BIs) selected from the research literature. The primary inputs for computing these BIs are uniaxial compressive strength (UCS) and the Brazilian tensile strength (BTS), which are typically measured for most projects using standard laboratory rock mechanics tests or obtained from log data. For the purposes of this experimental investigation, intact rock core samples were obtained from a carbonate–dolomite formation in Iran, comprising eight distinct geomechanical units, with measured values of UCS, BTS, and HTS ranging 29.7–162.2, 1.93–12.23, and 7.20–20.63 MPa, respectively. The measured HTS was found to directly correlate with the UCS, BTS, and Young's modulus, and inversely correlated with the rock porosity. Seven of the ten investigated BIs correlated with the measured HTS over 69% (R2 ≥ 0.69). In particular, the BI expressions developed by Yagiz and Gokceoglu, Ghadernejad et al., and Khandelwal et al. exhibited relatively strong correlations with the measured HTS (producing R2 values of 0.94, 0.87, and 0.86, respectively), suggesting that these three HTS–BI correlations could be used to provide preliminary HTS estimates for the investigated carbonate–dolomite formation in Iran. This work adds to a database that can be expanded to include other geographical regions for providing useful information about the selection of a suitable site or reserve for conducting HF operations. [ABSTRACT FROM AUTHOR]

Owing to the deep concave mining in Bayan Obo stope, the slope angle is steep, the terrain is high, the outcrop width of the crushing belt is large, the stability of many slopes is poor, and there are potential sliding surfaces. In this paper, through on-site investigation and sampling, the main factors affecting the landslide of the high and steep slopes of Bayan Obo are analyzed. Uniaxial compression tests were carried out to obtain the mechanical parameters of dolomite and slate. With the help of the three-dimensional digital speckle system, the whole process of slope landslide under rainfall conditions was studied through similar simulation and numerical simulation experiments. The influence of rainfall on the slope of Bayan Obo and the induced pattern of landslide were revealed. The experimental results show that rainfall is the key to inducing instability, the slippage at the edge of the slope is obvious, and there is seepage in the depths but the effect is not significant. The landslide can be roughly divided into the damage accumulation stage; the deformation development and expansion stage; and the unstable slip stage. [ABSTRACT FROM AUTHOR]

In response to the challenges of karst geophysical exploration in an environment with strong external interference, this paper proposes a new method, namely the frequency-Bessel transform method, for extracting multi-order dispersion curves of surface waves from background noise to characterize karst. The observation noise data of the Wuhan karst development area are used as an example, where the dolomitic limestone and limestone mixed with dolomite of the Jialing River Formation of the middle lower Triassic are widely developed in the observation area. The frequency-Bessel transform method involves performing a Bessel integral transformation on the cross-correlation coefficient of background noise in the frequency domain. Firstly, by synthesizing theoretical noise data and comparing it with the spatial autocorrelation method—which is currently the main method for extracting the fundamental dispersion curve of surface waves—it is verified that the frequency-Bessel transform method can extract the higher-mode dispersion curve. Then, by taking the actual measured single-point noise data as an example, the effect of applying the frequency-Bessel transform to the actual noise data is tested, and the inversion of the fine structure of the strata by the addition of higher-mode dispersion, the use of the damped least squares inversion method, and the joint inversion of fundamental and higher-mode dispersion curves are analyzed. The higher-mode dispersion curve of Rayleigh surface wave extracted by the frequency-Bessel transform is much clearer, and the 2D shear wave velocity structure profile obtained from inversion explains the karst development area, karst strip area, and thickness of the Quaternary overburden. The inferred results match with the actual borehole data. Multi-mode imaging of background noise based on the frequency-Bessel method can be applied to depict karst in complex backgrounds, and has significant potentiality in the field of ambient seismic noise tomography, providing a new idea and method for karst detection in near-surface engineering. [ABSTRACT FROM AUTHOR]

Deep and ultra-deep carbonate reservoirs are the focus of exploration and development in future. However, the problems of high pressures in the treatment process, a limited effective etching distance of acid, great acid leak-off, and poor adaptability of the acid system are encountered in this type of oil and gas reservoir. The mechanism of acid fracturing stimulation under different processes and parameters is not clear. Aiming at these issues, the treatment schemes, process optimization, parameter optimization, and liquid system screening are studied in this paper, try to clarify the acid fracturing stimulation mechanism, and the following conclusions are drawn: The acid network fracturing could activate natural fracture to generate a complex fracture network to the greatest extent, and thereby a high output could be achieved; By using of weighted fracturing fluid, the wellhead injection pressure, as well as the performance of equipment required, could be effectively reduced; With 20% gelling acid and 20% retarded acid system, the non-uniform etching could be realized to improve the effective etching distance of acid liquid. The conclusions in this paper shed light on the acid fracturing treatment of deep and ultra-deep carbonate rocks. [ABSTRACT FROM AUTHOR]

Ultra-High Molecular Weight Polyethylene (UHMWPE) polymers have been used in biomedical applications due to its biocompatibility, durability, toughness and high wear resistance. To enhance the mechanical properties, various types of minerals are commonly utilized as fillers in UHMWPE. One of the minerals is dolomite, which has been recognized as a valuable mineral with versatile applications, particularly in the field of biomedical applications. This paper presents the tensile properties of UHMWPE composites that filled with dolomite and treated-dolomite at various filler loading (i.e., 1-5 wt.%). Nitric acid and diammonium phosphate were used to treat the dolomite. From the results, the peaks of the FTIR spectrum displays carbonate (CO3-2), phosphate (PO4-3) and hydroxyl (OH-) groups in the ct-dolomite powder sample while the XRD pattern reveals that using dolomite treated with 1M nitric acid resulted in the presence of calcium hydroxide phosphate (Ca10(PO4)5(OH)) and MgO. For tensile strength, UHMWPE/ct-dolomite composites show better tensile strength than the pure UHMWPE composites. Treated improve the dolomite filler and resulted in significantly better matrix-filler interfacial interactions and improve the properties. [ABSTRACT FROM AUTHOR]

Siliceous minerals of the Dengying Formation in the Gaoshiti–Moxi area in the central Sichuan Basin exhibit four types of quartz crystals (cryptocrystalline quartz, chalcedony, microcrystalline quartz, and megacrystalline quartz) and three structural types: cryptocrystalline, microcrystalline, and mosaic (laminated mosaic, window-hole interrupted mosaic, and arc-laminated mosaic). Siliceous minerals have a great influence on the storage performance of the reservoirs in the Dengying Formation. According to the petrophysical parameters of the Dengying Formation and porosity intersection diagrams, the siliceous dolomite and the reservoirs have low impedance characteristics, which makes it difficult to distinguish between them and leads to difficulties in the characterization and prediction of the reservoirs. The transverse wave velocity is favorable for reservoir characterization. Currently, the main method used to estimate the transverse wave velocity is petrophysical modeling, which establishes a relationship between the elastic and physical parameters of the reservoir. In this paper, the siliceous minerals in the dolomite in the study area are regarded as solid inclusions, and the calculation method of the rock matrix modulus is improved by using solid replacement. Then, an improved petrophysical model is constructed by combining the KT (Kuster–Toksöz) model, the DEM (Discrete Element Method) model, the Gassmann equation, and the Wood equation. The transverse wave velocity is estimated using the improved model under the constraint of the longitudinal wave velocity. The shapes of the transverse wave velocity curves obtained by the improved model and the deviations from the measured velocities are significantly better than those of the Xu–Payne model and other models. The results show that the improved model can effectively estimate the transverse wave velocity of the reservoir in this area, which provides a basis for future reservoir predictions in this area. [ABSTRACT FROM AUTHOR]

In the field of mineral processing, the successful flotation of target minerals requires sufficient liberation through grinding. The aim of this paper is to compare and evaluate the performance of ball versus short cylindrical media for comminution of dolomite by point and line contact, respectively. The results of the grinding experiments indicate that short cylinders generate more angular particles with intermediate sizes and exhibit a higher grinding efficiency compared to balls. The Population Balance Model demonstrates the distribution of broken fragment sizes during the breaking stage for each size range. The results of the DEM (discrete element method) grinding simulation are consistent with the experimental findings in terms of the distribution of particle sizes, the shape of the particles, and the distribution of broken fragment sizes. Furthermore, short cylinders selectively produce more active {104} crystal surface of dolomite, which possess a higher adsorption capacity with collectors and are preferentially floated as the concentrate. In reverse flotation for removal of dolomite, tests confirm that the products obtained from grinding with short cylinders exhibit a higher flotation recovery of dolomite compared to those obtained from ball grinding. This study provides a reference scheme for optimizing the grinding and flotation processes of valuable minerals. [ABSTRACT FROM AUTHOR]

Smithsonite, dolomite, and calcite are carbonate minerals. The crystal structures and spatial distribution characteristics of their common surface metal sites are similar, leading to difficulty in the flotation separation of smithsonite from these carbonate gangues. In this paper, the floatability of smithsonite, dolomite, and calcite in sodium oleate, salicylhydroxamic acid, and their combined-collector system were systematically studied through single-mineral flotation tests, respectively. The results showed that it was difficult to obtain a noticeable recovery difference between smithsonite–calcite and smithsonite–dolomite in a single-collector system of sodium oleate and salicylhydroxamic acid, both at the same time. In the combined-collector system of salicylhydroxamic acid and sodium oleate with total dosage of 6 × 10−4 mol/L, molar ratio of 3:1, and pH of 8.0, the recovery difference of smithsonite–calcite and smithsonite–dolomite could reach the highest values of 38.46% and 37.98%, respectively, while obtaining the highest smithsonite recovery of 88.19%. The adsorption mechanism of the combined collectors was investigated via Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, a collector adsorption test, and zeta potential measurements, respectively. [ABSTRACT FROM AUTHOR]

The paper presents experimental results obtained in the manufacturing process of porous high-strength glass foam for thermal insulation in buildings made of glass waste and kaolin clay as raw materials and dolomite as a foaming agent. The paper’s originality is the use of the unconventional microwave heating technique. The best product manufactured by this technique was that sintered at 1050 ºC using 18 wt.% kaolin clay and 3.5 wt.% dolomite. The product characteristics were: the apparent density of 0.66 g·cm-3, the thermal conductivity of 0.155 W/m·K, the compressive strength of 5.3 MPa and a microstructural homogeneity with pore size between 0.20-0.50 mm. [ABSTRACT FROM AUTHOR]

In order to enhance the development efficiency of thick and complex carbonate reservoirs in the Middle East, a case study was conducted on M oilfield in Iraq. This study focused on reservoir characterization, injection-production modes, well pattern optimization, and other related topics. As a result, key techniques for the high-efficiency development of thick carbonate reservoirs were established. The research findings include the following: (1) the discovery of hidden "low-velocity" features within the thick gypsum-salt layer, which led to the development of a new seismic velocity model; (2) the differential dissolution of grain-supported limestones is controlled by lithofacies and petrophysical properties, resulting in the occurrence of "porphyritic" phenomena in core sections. The genetic mechanism responsible for reversing petrophysical properties in dolostones is attributed to "big hole filling and small hole preservation" caused by dense brine refluxing; (3) fracture evaluation technology based on anisotropy and dipole shear wave long-distance imaging was developed to address challenges associated with quantitatively assessing micro-fractures; (4) through large-scale three-dimensional physical models and numerical simulations, it was revealed that water–oil displacement mechanisms involving "horizontal breakthrough via hyper-permeability" combined with vertical differentiation due to gravity occur in thick and heterogeneous reservoirs under spatial injection-production modes; (5) a relationship model linking economic profit with well pattern density was established for technical service contracts in the Middle East. Additionally, an innovative stepwise conversion composite well patterns approach was introduced for thick reservoirs to meet production ramp-up requirements while delaying water cut rise; (6) a prediction technology for the oilfield development index, considering asphaltene precipitation, has been successfully developed. These research findings provide robust support for the efficient development of the M oilfield in Iraq, while also serving as a valuable reference for similar reservoirs' development in the Middle East. [ABSTRACT FROM AUTHOR]

This document is an editorial for a special issue of the journal Minerals, focusing on the heterogeneities of carbonate reservoirs. The editorial emphasizes the importance of understanding these heterogeneities for optimizing exploration and production strategies, as they influence fluid flow behavior and the recoverable reserves within the reservoir. The editorial also highlights the need for further research to explore the implications of heterogeneities at a broader scale and recommends the use of advanced technologies and multidisciplinary approaches. The document provides a summary of five papers included in the special issue, which cover topics such as the genetic mechanism of dolomite reservoirs, diagenetic alterations in the Chiltan Formation, the formation mechanism of dolomite-mottled limestone reservoirs, characteristics of crystalline dolomites in the Sanshanzi Formation, and facies variations in the Sarvak Formation. The research presented in this special issue contributes to our understanding of ancient carbonate platforms and dolomite reservoirs and provides a framework for future studies in oil and gas exploration. [Extracted from the article]

Crushed dolomite stone can be used as a part of concrete for hot weather. Fine dolomite as a filler is not commonly included in Portland cement. In this paper, the properties of a blended binder based on Portland cement and dolomite filler are presented. Dolomite filler was obtained from dust grains by mechanical activation in a laboratory ball mill to increase the specific surface area and its chemical activity. It is shown that the impact of mechanical activation allows to obtain dolomite filler with a median particle size of 1.4 μm and a specific surface area of 639.9 m2/kg. The content of dolomite filler in Portland cement was 10, 30 and 50%. The main properties of blended cements, i.e., the standard consistency, setting time, compressive strength, average density, and drying shrinkage, were determined on pastes. The mineralogical composition of the hydrated pastes was determined by XRD at 28 days. The presence of dolomite filler at levels higher than 10% decreases the compressive strength of blended cements. The dolomite filler decreases the water demand, shortens the setting time, and mitigates the development of drying shrinkage in the blended binder. To prevent concrete cracking, the application of dolomite filler in blended cement is relevant in hot weather due to its reduced drying shrinkage. [ABSTRACT FROM AUTHOR]

This work describes a procedure for building a high-quality 3D model of a rocky pinnacle in the Dolomites, Italy, using Structure from Motion (SfM) techniques. The pinnacle, known as "Campanile di Val Montanaia", is challenging to survey due to its high elevation and sub-vertical cliffs. The construction of the 3D model is the first step in a multi-disciplinary approach to characterize the rock mass and understand its behavior and evolution. This paper discusses the surveying operations, which involved climbing the pinnacle to collect Ground Control Points (GCPs) and using a UAV to capture aerial imagery. The photographs were processed using SfM software to generate point clouds, mesh, and texture, which were then used for rock mass discontinuity mapping. The study compares models of different qualities and point densities to determine the optimal trade-off between processing time and accuracy in terms of discontinuity mapping. The results show that higher quality models allow for more detailed mapping of discontinuities, with some drawbacks due to noise in the case of the densest solution (e.g., increase in frequency of outliers across the point cloud). These pros and cons are also discussed in relation to the computational cost necessary to build the models. The study also examines the limitations and challenges of performing discontinuity mapping in the different models, including subjectivity in interpretation. A further element of interest is the publication of a high-quality 3D georeferenced model of the "Campanile di Val Montanaia" to be used for several potential further applications, such as stability analyses and numerical modeling. [ABSTRACT FROM AUTHOR]

Copyright of Iraqi Journal of Chemical & Petroleum Engineering is the property of Republic of Iraq Ministry of Higher Education & Scientific Research (MOHESR) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Sandy dolomite, being a soluble rock, is prone to dissolution and erosion caused by groundwater, leading to the formation of underground caves and fractures. This may result in geological disasters such as ground subsidence and collapse. In this paper, the changes and mechanical properties of black sandy dolomite after hydrochemistry are studied. A semi-immersion test with different concentrations of iron sulfate solution was carried out to simulate the water-rock interaction in different water environments. After that, scanning electron microscope (SEM) results could reflect the dissolution and pore development of rock by the effect of water-rock interaction from the microscopic. Water-rock interaction enlarges cracks in rocks and dissolves pyrite, carbonate minerals, and other components, reducing the cementation between particles. The change in the mechanical properties of black sandy dolomite under water-rock chemical interaction was revealed by uniaxial compression test. The mechanical properties of the samples exhibit varying degrees of deterioration, with strain increased ranging from 4.96 to 29.58%. The brittleness index modified (BIM) values for each sample ranged from 5.20 to 6.20%, all of which are larger than 4.70% in the natural state. [ABSTRACT FROM AUTHOR]

Pore fluids control the diagenetic processes and storage spaces of deep clastic rock reservoirs and have become a major area of interest within the fields of sedimentology and petroleum geology. This paper aims to relate the diagenetic processes of the Oligocene Zhuhai sandstones in the Baiyun Sag to pore fluids varying with burial depth. The types and distribution patterns of authigenic minerals are investigated through analysis of petrographic, mineralogical, and geochemical features to illustrate the origin and flow patterns of pore fluids and their influences on reservoir diagenesis. Strong cementation of eogenetic carbonate cement near the sandstone–mudstone interface was a consequence of material migration from adjacent mudstones on a large scale. The pore fluids were mainly affected by microbial methanogenesis and carbonate mineral dissolution in adjacent mudstones during eogenesis. The pore fluids were diffusively transported in a relatively open geochemical system within a local range. Support for this model is provided by the heavier stable isotopic values present in eogenetic calcite and dolomite. Feldspar dissolution during early mesogenesis was spatially accompanied by the precipitation of authigenic quartz and ferroan carbonate cement. Pore fluids in this period were rich in organic acids and CO2, and their migration mechanism was diffusive transport. The obviously lighter carbon and oxygen isotopic compositions of the ferroan calcite support this inference. During late mesogenesis, the input of deep hydrothermal fluid might have been partly responsible for the precipitation of ankerite, barite and authigenic albite. Oil charging may have inhibited carbonate cementation and compaction, accordingly preserving porosity, and together with authigenic kaolinite, might have promoted the transition of the reservoir from water wet to oil wet to the benefit of oil entrapment. The findings reported here shed new light on the evaluation and prediction of sandstone reservoirs that have experienced multiple periods of fluid flow. [ABSTRACT FROM AUTHOR]

Petrography, fluid-inclusion microthermometry, stable isotope analyses, and radiometric (206Pb/238U) dating of Upper Triassic dolostones, saddle dolomite, and quartz and calcite cements were used to constrain the timing and conditions of dolomitization and cementation in the context of the tectonic evolution of a basin in the northern United Arab Emirates. Dolomitization (ca. 152.4 Ma) and precipitation of saddle dolomite (ca. 146.8 Ma), calcite (ca. 144.6 Ma), and quartz cements are attributed to focused synrifting flow of hot basinal brines into grain-supported limestones in which permeability was enhanced by incursion of meteoric waters beneath a disconformity surface. Another calcite cement generation (ca. 99.7 Ma) was formed by flow of hot brines during tectonic compression related to the obduction of Oman ophiolites in the Late Cretaceous. Thus, this paper provides new insights into (1) stratigraphic controls on and timing of hydrothermal (hot basinal brines) dolomitization, (2) the origin of closely associated intraformational limestones and dolostones, and (3) linkages between diagenesis and thermochemical modifications of basinal brines during tectonic evolution of sedimentary basins. [ABSTRACT FROM AUTHOR]

With the great breakthrough in natural gas exploration of Paleozoic Taiyuan formation in Longdong exploratory area in the southwestern part of Ordos Basin, it is urgent to solve the petrological nomenclature of sedimentary bauxite, so as to further study the pore formation mechanism, distribution law, and controlling factors of bauxite reservoirs. In this paper, X-ray diffraction, polarizing microscope, scanning electron microscope, and other methods are used to analyze the mineral composition and structure of bauxite rocks in the study area and give appropriate names. The results show that the sedimentary sequence of bauxite in the study area can be divided into five sections: A, B, C, D, and E. The main mineral components are diaspore (C section content can be more than 90%), illite, kaolinite, and chlorite; accessory mineral include anatase and pyrite; trace components include quartz, feldspar, rutile, hematite, and rock salt; and some of the pores are filled with calcite, siderite, and (iron) dolomite. The rock structure is mainly bedding and massive structure, and some of them have geopetal structure. The texture mainly consists of granular texture, grain (powder crystal) texture, gel texture, and algal bonding texture. Considering the special lithology of section A~C and the lack of existing nomenclature method, based on mineral composition and sedimentary fabric, a triangulation classification nomenclature method is established, which adopts structure+texture as secondary name and the main mineral components diaspore-mud-pyrite of the three end-member mineral components as primary name. It can not only highlight the mineral assemblage characteristics of sedimentary sequence of bauxite but also reflect the lithologic characteristics of reservoir development section and the influencing factors of reservoir formation, effectively reflecting the petrological characteristics of bauxite reservoir. Among them, the diaspore rocks with granular, bean-oolitic, and grain texture are the main lithologies forming the natural gas reservoir space of Taiyuan formation in Longdong area. The naming method is feasible and reliable for sedimentary bauxite rocks, which lays a good foundation for the study of natural gas reservoir, pore formation mechanism, and distribution law in Longdong area, southwest of the basin. [ABSTRACT FROM AUTHOR]