Search

A terminal ballistic analysis of the effects of 7.62 mm X 51 AP P80 rounds on inclined high-strength armor steel plates is the focus of the presented study. The findings of an instrumented ballistic testing combined with 3D advanced numerical simulations performed using the IMPETUS Afea® software yielded the conclusions. The experimental verification proved that slight differences in the pitch-andyaw angles of a projectile upon an impact caused different damage types to the projectile's core. The residual velocities predicted numerically were close to the experimental values and the calculated core deviations were in satisfactory agreement with the experimental results. An extended matrix of the core deviation angles with combinations of pitch-and-yaw upon impact angles was subsequently built on the basis of the numerical study. The presented experimental and numerical investigation examined thoroughly the influence of the initial pitch and yaw angles on the after-perforation projectile's performance. [ABSTRACT FROM AUTHOR]

In this paper, the effect of soft-hard plate and rubber thickness as absorbent impact against on ballistic resistance with 5.56 x 45 mm caliber deformable projectile is investigated. The characteristic of ballistic impact for each configuration target is obtained and compared based on the investigation of the hardness effect of the front plate and the thickness of rubber. The experimental results approached by simulation with finite element method were used to know several characters due to the ballistic impact. The experiment and simulation results showed that the projectile is able to perforate front plate and the impact on the back plate form a bulge on every configuration. The configuration of hard plate as front plate reveals minimum ballistic impact due to the projectile rate. The simulation shows that the maximum stress concentration occurs only on the front plate, so the front plate fails. [ABSTRACT FROM AUTHOR]

In this study, the penetration behaviour of a Mild Steel Cored (MSC) round, 7.62 mm in diameter and 39 mm in length, commonly known as the AK47 round, was studied since it still forms an important part of the threat spectrum for personnel body armour systems. Likewise, boron carbide strike face materials were selected since this armour material is often the material of choice for ultralightweight body armour systems for protection against this particular threat. The presence of two, relatively soft, intermediate materials (the copper jacket and filler material of the bullet, and a fibre-reinforced polymer cladding layer on the ceramic) between the mild steel core and the boron carbide target was examined using reverse ballistics techniques, flash x-radiography and round recovery measurements. This was supported by selective numerical simulations using the computer code ANSYS-AUTODYN. It was found that stripping of the jacket, from the AK47 MSC rounds, makes a difference to its penetrating ability: the mild steel core is significantly reduced in length, and mass, when the jacket is not present. The magnitude of this effect is much greater than previously reported for high-strength steel-cored rounds and for tungsten carbide-cored rounds. The penetration event appears to be a twostage process: mushrooming of the mild steel core on, or near, the surface of the ceramic, followed by a linear erosion process as the core penetrates the ceramic itself. The second step has not been reported previously for MSC rounds. [ABSTRACT FROM AUTHOR]

Plastilina is often used as a ballistic witness material (BWM) behind the armour to evaluate the backface signature (BFS). Indeed, it is cheap, reusable and it keeps its deformation after being impacted. Moreover, while it aims at evaluating the performance of ballistic protections when no perforation occurs, it can be subjected to a very wide range of strain/shear rates during a ballistic impact. Therefore, there is a need to improve the knowledge about the mechanical/rheological response of such a material. This paper proposes both experimental and modelling approaches to determine the response of the specific ballistic plastilina red Weible® over a wide range of shear/strain rate. A capillary rheometry analysis with control of temperature was performed up to 8.104 s-1. The corrections of Rabinowitsch and Bagley were applied and an attempt of the analysis of Mooney was considered. From the rheology of plasticine, a two-parameters based power-law constitutive equation was deduced. An experimental drop test was carried out using a specific standard setup. A high-speed camera was used for measuring the penetration depth of a steel ball into the plastilina. A numerical simulation of the drop test was performed by taking into account the mechanical properties of the plastilina. A good correlation was observed between the experimental and numerical results in terms of indentation depth evolution. [ABSTRACT FROM AUTHOR]