Search

Chemical manipulation of surface functional groups on two‐dimensional transition metal carbides and/or nitrides (MXenes) provides a wide range of design and application prospects. However, achieving rapid targeted modification of surface groups remains a significant challenge. Herein, we propose a general strategy to swiftly shear and customize surface groups on Ti3C2Tx−MXene via the flash Joule heating (FJH) reaction within 1 s. Successfully, MXenes with 9 target terminations, including VII A (F, Cl, Br, or I), VI A (O, S, or Se), and V A (N or P), either single or multiple, are synthesized, with a surface content of up to about 76 %. The impact of these terminations is systematically analyzed on electrochemical performance, demonstrating that VI A and V A terminations have higher electrochemical activity than VII A. Particularly, N‐, S‐, and O‐terminated MXenes exhibit enhanced specific capacities and undecayed cycling performance. These findings offer valuable insights for the surface engineering design and performance optimization of functional materials. [ABSTRACT FROM AUTHOR]

Aqueous zinc‐ion batteries (ZIBs) hold significant promise for large‐scale energy storage. While considerable strides have been made in modifying separators, the challenge of developing dendrite‐free, corrosion‐resistant, and cost‐effective separators for achieving extended cycling performance of Zn anodes persists. In light of this, a TiO2 coating separator to mitigate interfacial corrosion and passivation reactions, thereby facilitating high‐performance ZIBs is designed. This study delves into the influence of the loading amount and crystal phase of the TiO2 coating layers on separator modification. Zn symmetric cells employing the anatase TiO2‐modified glass fiber (A‐TiO2@GF) separator demonstrate superior Zn2+ ion transport kinetics in a mild ZnSO4 electrolyte, ensuring sustained long‐term stability and uniform Zn deposition. Furthermore, the reduced hydrogen evolution reaction (HER) activity of A‐TiO2 coatings curbs H+ ion migration, minimizing interfacial corrosion and HER. Consequently, the assembled Zn||CaV8O20 zinc‐ion full cells demonstrate outstanding long‐term durability and impressive specific capacity, boasting a discharge capacity of 142 mAh g−1 after 1000 cycles. This work introduces a straightforward interface engineering strategy for creating efficient separators in zinc‐ion batteries, promoting uniform Zn deposition. [ABSTRACT FROM AUTHOR]

Aqueous zinc ion batteries (AZIBs) have stimulated extensive attention due to their environmental friendliness and low cost. Unfortunately, the inevitable dendrite growth and corrosion on the zinc (Zn) anode severely hinder the practical application of AZIBs. Herein, an amino acid containing an imidazole group is introduced as an effective additive to address these issues. The dynamic conversion of amino acid and protonated amino acid creates a pH buffer function that regulates solution pH in real time, inhibits hydrogen evolution reaction (HER), and eliminates notorious by‐products. In addition, the protonated amino acid is preferentially adsorbed on the Zn anode, preventing contact of the active water with the Zn surface and promoting homogeneous Zn deposition. Thus, the amino acid‐based electrolyte promotes dendrite free plating/stripping with a Coulombic efficiency up to 99.67% and cycle lifetime of 2600 h. In particular, a depth of discharge of up to 87% can be achieved with an ultra‐high areal capacity of 24 mAh cm−2. The developed Zn||CVO full cell also exhibits better electrochemical performance than that without additives. This work provides an effective and convenient approach for safe and efficient Zn‐ion batteries. [ABSTRACT FROM AUTHOR]

The lack of high‐performance electrodes is a key factor restricting the development of sodium‐ion batteries (SIBs), and usually a certain type of electrode material alone often fails to combine the merits of high capacity and good conductivity. Herein, nitrogen‐doped carbon (NC) was used as a multifunctional bridge to uniformly compound high‐capacity MoS2 nanoparticles with highly conductive Ti3C2Tx nanosheets to form Ti3C2Tx@MoS2/NC composite with flower‐like architecture. Ultrafine MoS2 nanoparticles were uniformly anchored on Ti3C2Tx nanosheets to form nanosheets primary building blocks with a sandwich‐like architecture, which not only shortens the ion transfer distance but also enlarges the layer spacing of Ti3C2Tx favoring the storage of more sodium ions as well as their transport capacity. Moreover, the flower‐like structures with abundant edges can provide an ample active sites and high pseudocapacitance behavior. As a result, flower‐like Ti3C2Tx@MoS2/NC displays a high electrochemical properties with an excellent cycling stability over 2000 cycles (81.4 % capacity retention) and preeminent rate capacity of 383 mAh g−1 at 30 A g−1. Furthermore, Ti3C2Tx@MoS2/NC‖Na3V2(PO4)3 full cell displays a capacity of 59 mAh g−1 at 0.4 A g−1 after 180 cycles. This work displays a high‐performance anode composite for SIBs and provides insight into the preparation of other composites. [ABSTRACT FROM AUTHOR]

As post‐lithium ion batteries, both sodium‐ion batteries (SIBs) and potassium ion batteries (PIBs) possess great potential for large scale energy storage. However, the application of both SIBs and PIBs are hindered by the lack of suitable electrode materials. Here, we synthesized the sulfur decorated Ti3C2Tx (S−T3C2Tx) MXene as electrode material for SIBs and PIBs. Thanks to the sulfur functional group and the formation of Ti−S bond, which facilitates the sodium in‐/desertion and strengthens the potassium ion adsorption ability, as well as enhances ion reaction kinetics and improved structure stability, the S−T3C2Tx exhibit excellent sodium/potassium storage performance, high reversible capacities of 151 and 101 mAh g−1 at 0.1 mA g−1 were achieved for SIBs and PIBs, respectively. Moreover, the S−T3C2Tx exhibits remarkable long‐term capacity stability at a high density of 500 mA g−1, providing an impressive storage of 88 mAh g−1 for SIBs and 41 mAh g−1 for PIBs even after 2000 cycles. This work could give a deep comprehension of the heteroatom modification influence on the MXene‐based framework and promote the application of MXene electrodes. [ABSTRACT FROM AUTHOR]

Organic polymers have been considered reliable candidates for lithium storage due to their high capacity and lack of volume expansion. Compared with other organic polymers, polyimide has become a very promising electrode material for lithium‐ion batteries (LIBs) because of its easy synthesis, customizable structure and structural stability. A large number of studies have confirmed that the benzene ring structure of polyimide has strong lithium storage capacity as an anode material. Hence, we designed and synthesized polyimide organic polymer (PBPAQ) for the first time. The unique spherical flower structure of this material enhances the interaction between the electrode material and the electrolyte by increasing the contact area. The PBPAQ anode has a specific discharge capacity of 738 mAh g−1 after 100 cycles at 0.1 A g−1. The excellent lithium storage performance of this material laid a foundation for the research of the anode of LIBs in the future. [ABSTRACT FROM AUTHOR]

Binders play a critical role in rechargeable lithium‐ion batteries (LIBs) by holding granular electrode materials, conductive carbons, and current collectors firmly together to form and maintain a continuous electron conduction phase with sufficient mechanical strength. In the commercial LIBs, the dominant binder is polyvinylidene fluoride for the cathode (LiCoO2, LiFePO4, LiNixCotyMnzO2, etc.) and carboxyl methylcellulose/styrene‐butadiene rubber for the anode (graphite and Li4Ti5O12). However, these polymer binders have several drawbacks, particularly, a lack of electronic and lithium‐ion conductivities. Here, a novel organic/inorganic hybrid conductive binder (LAP‐rGO) for both the anode and cathode of LIBs is reported. The binder consists of 2D reduced graphene oxide sheets with anchored long alkane chains. Electrodes prepared using this binder exhibit sufficient high bond strength, fast electrolyte diffusion, high rate charge/discharge performance, and excellent cycling stability. Around 130 mAh g−1 capacity enhancement at 5C is demonstrated for LiFePO4 and Li4Ti5O12 electrodes owing to the combined improvement in electron and lithium ion transportation. LAP‐rGO bond graphite anode shows specific capacity beyond its theoretical value. Electrode slurries prepared using this new binder have superior processing and coating properties that can be prepared under a high humidity and dried using less energy. [ABSTRACT FROM AUTHOR]

Aqueous Mg ion batteries (AMIBs) show great potential in energy storage for their advantages of high capacity, abundant resource, and environmental friendliness. However, the development of AMIBs is limited due to the scarcity of suitable anode materials. In this study, a new polymer anode material (PNTAQ) with flower‐like nanosheet structure is synthesized for aqueous Mg‐Na hybrid‐ion battery (AMNHIB). PNTAQ possess carbonyl functional groups which can be oxidized and reduced reversibly in aqueous solution containing alkaline metal ions. PNTAQ displays a discharge specific capacity of 245 mAh g−1 at 50 mA g−1 in 1 M MgCl2 + 0.5 M NaCl electrolyte, which is much higher than that in single 1 M MgCl2 or 0.5 M NaCl electrolyte. Even cycling at 1000 mA g−1 for 1000 times, the capacity retention can still maintain at 87.2%. A full Mg‐Na hybrid‐ion cell is assembled by employing β‐MnO2 as cathode and PNTAQ as anode material, it exhibits a specific capacity of 91.6 mAh g−1 at 100 mA g−1. The polymer electrode material well maintains its framework structure during the discharge/charge cycling process of the hybrid‐ion battery. [ABSTRACT FROM AUTHOR]

To relieve the overwhelming pressure on fossil energy, aqueous magnesium ion batteries attracted tremendous attention owing to their low cost and high safety. However, the cathode materials are apt to occur lattice distortion because of the electrostatic interaction between magnesium ions and crystal. The 2×2 manganese octahedral molecular sieve with potassium ions and water located in the tunnels (K‐OMS‐2), utilized as a cathode material for chargeable magnesium ions batteries, is exposed to irreversible Mg2+ intercalation/deintercalation due to lattice distortion, which heavily damages the electrochemical properties and declines the capacity. Herein, we carry out an ion doping strategy to overcome the above issues, leading to an enhanced Mg Mg2+ storage behavior. The Nb or V cation is successfully doped into K‐OMS‐2 by a facile reflux method under room temperature. The specific surface area is enlarged by the addition of cations, which promise a large electrode‐electrolyte contact area. The Nb and V doped K‐OMS‐2 present a capacity of 252.6 and 265.9 mAh/g at 20 mA/g, respectively. This work demonstrates an ion doping approach toward exploiting the stable and high‐capacity Mg‐ion battery cathode and provides potential cathode materials for a large‐scale aqueous Mg‐ion‐based energy storage system. [ABSTRACT FROM AUTHOR]

Aqueous Mg‐ion batteries (MIBs) lack reliable anode materials. This study concerns the design and synthesis of a new anode material – a π‐conjugate of 3D‐poly(3,4,9,10‐perylenetracarboxylic diimide‐1,3,5‐triazine‐2,4,6‐triamine) [3D‐P(PDI‐T)] – for aqueous MIBs. The increased aromatic structure inhibits solubility in aqueous electrolytes, enhancing its structural stability. The 3D‐P(PDI‐T) anode exhibits several notable characteristics, including an extremely high rate capacity of 358 mAh g−1 at 0.05 A g−1, A 3D‐P(PDI‐T)‖Mg2MnO4 full cell exhibits a reversible capacity of 148 mAh g−1 and a long cycle life of 5000 cycles at 0.5 A g−1. The charge storage mechanism reveals a synergistic interaction of Mg2+ and H+ cations with C−N/C=O groups. The assembled 3D‐P(PDI‐T)‖Mg2MnO4 full cell exhibits a capacity retention of around 95 % after 5000 cycles at 0.5 A g−1. This 3D‐P(PDI‐T) anode sustained its framework structure during the charge–discharge cycling of Mg‐ion batteries. The reported results provide a strong basis for a cutting‐edge molecular engineering technique to afford improved organic materials that facilitate efficient charge‐storage behavior of aqueous Mg‐ion batteries. [ABSTRACT FROM AUTHOR]

Lithium metal anode is the most ideal candidate for next‐generation energy storage system. However, the uncontrolled dendrite growth, infinite volume expansion, and undesired side reactions lead to serious safety issues and hinder their potential application. Herein, a pre‐lithiation strategy is proposed to construct a high‐lithiophilic Cu‐Li2O matrix on commercial Cu foil. The in situ‐generated Li2O promises adequate nucleation sites and strengthens solid electrolyte interphase and lateral lithium deposition. Meanwhile, the existence of 3D matrix reduces the local current density. The synergy effect of Li2O and Cu suppresses the growth of lithium dendrites. As a result, Cu‐Li2O matrix reveals an enhanced lithium plating/stripping behavior with Coulombic efficiency of 98.46% after 270 cycles. The symmetrical cell assembled by Li‐plated electrodes displays a prolonged lifespan of 1400 h. The work demonstrates a scalable and effective approach for modified current collectors toward stable Li metal anode. [ABSTRACT FROM AUTHOR]

The article titled "Enhancing Electrochemical Performance through Swift Functional Group Tuning of MXenes" discusses the use of flash Joule heat (FJH) technology to modify the surface of MXene materials. The researchers demonstrate that this technique can be used to cut and modulate the terminations on the MXene surface within 1 second. The study shows that certain terminations, specifically VI A and V A, outperform VII A terminations in terms of electrochemical performance. For more information, readers can refer to the research article by Y.-Z. Fang, D. Cao, and their colleagues. [Extracted from the article]

As a recently emerging group of 2D materials, MXene has attracted extensive attention in the energy storage field in recent years owing to their outstanding features. However, the notorious issues of inevitable oxidation stability and surface‐to‐surface self‐restacking for MXene significantly prevent its further wide‐ranging application. Herein, the 3D macroporous oxidation‐resistant Ti3C2Tx MXene/graphene/carbon nanotube (MRC) hybrid hydrogels are prepared by a simple gelation method assisted by l‐cysteine as crosslinker and l‐ascorbic acid (VC) as reductant. Benefitting from the effectively alleviated restacking, excellent electrical conductivity, and the 3D inter‐crosslinked macroporous architecture, as a supercapacitor electrode, the obtained MRC aerogel exhibits a superior specific capacitance of 349 F g−1, unparalleled rate capability (52.0% at 3000 mV s−1) and amazing cyclic stability (retention of 97.1% after 100 000 cycles). Moreover, the 3D MRC‐30 aerogel exhibits an impressive oxidation‐resistant performance with just a 9.3% increase in electrical resistance after storing in ambient condition for 60 days, effectively alleviating the oxidation problem of MXene. This work demonstrates a new method for construction of 3D oxidation‐resistant MXene hydrogel, shedding new light on the promising applications of MXene materials, especially in high humidity and oxygen environment. [ABSTRACT FROM AUTHOR]

Sodium‐ion hybrid capacitors (SIHCs) are considered a prospective alternative to lithium‐ion batteries (LIBs) since there are rich and available sodium reserves. Here, nitrogen‐doped carbon tubes (N‐MJ) derived from metaplexis japonica fluff are prepared by using a facile method of etching and peeling the fluff with urea to prepare a Na+ storage anode. With prominent traits in terms of structure and a high nitrogen content (11.08 %), N‐MJ exhibits exceptional Na+ storage performance with a high reversible capacity (390.9 mAh g−1 at 50 mA g−1) and excellent long‐term circulation (208.1 mAh g−1 after 2650 cycles at 1 A g−1). Systemic kinetic analysis manifests that the extraordinary performance is responsible for the large‐scale capacitance control. Furthermore, the SIHCs assembled by using N‐MJ and activated carbon (AC) presents a maximum energy density of 111.4 Wh kg−1 (at 445.8 W kg−1) and power density of 2455.2 W kg−1 (at 34.1 Wh kg−1). Notably, the developed SIHCs maintain a 100 % capacity retention rate at 1 A g−1 after 5000 cycles. Overall, our work not only provides a good choice for storage Na+ anode materials, but also supplies a feasible method for the recycling of waste biomass. [ABSTRACT FROM AUTHOR]

Molybdenum trioxide (MoO3) has recently aroused intensive interest as a renowned conversion‐type anode of Li‐ion batteries (LIBs). Nevertheless, the inferior rate capability, sluggish reaction kinetics, and fast capacity decay during a long‐term charge/discharge process seriously inhibits large‐scale commercial application. Herein, abundant oxygen vacancies and MXene nanosheets are elaborately introduced into MoO3 nanobelts through hydrazine reduction and electrostatic assembly to accelerate the ionic and electronic diffusion/transport kinetics for LIBs. Benefitting from the accelerated ion diffusion kinetics, enhanced electrical conductivity, and additional active sites induced by oxygen vacancies as well as the robust interfacial contact, the prepared MoO3−x/MXene heterostructure exhibits excellent lithium‐ion storage performances. First‐principles calculations indicate that the adsorption of Li+ ion and the electrical conductivity are significantly enhanced for the MoO3−x/MXene heterostructure. Thus, the composite exhibits high reversible capacity of 1258 mAh g−1 at 0.1 A g−1 for Li‐ion storage and retains 474 mAh g−1 at 10 A g−1, remarkably higher than those of the previously reported MoO3‐based anode materials. More importantly, the composite is fabricated with commercial LiFePO4 into a full LIB, which displays an unparalleled energy density of 330 Wh kg−1. [ABSTRACT FROM AUTHOR]

2D MXene materials have attracted intensive attention in energy storage application. However, MXene usually undergoes serious face‐to‐face restacking and inferior stability, significantly preventing its further commercial application. Herein, to suppress the oxidation and self‐restacking of MXene, an efficient and fast self‐assembly route to prepare a 3D porous oxidation‐resistant MXene/graphene (PMG) composite with the assistance of an in situ sacrificial metallic zinc template is demonstrated. The self‐assembled 3D porous architecture can effectively prevent the oxidation of MXene layers with no evident variation in electrical conductivity in air at room temperature after two months, guaranteeing outstanding electrical conductivity and abundant electrochemical active sites accessible to electrolyte ions. Consequently, the PMG‐5 electrode possesses a striking specific capacitance of 393 F g−1, superb rate performance (32.7% at 10 V s−1), and outstanding cycling stability. Furthermore, the as‐assembled asymmetric supercapacitor possesses a pronounced energy density of 50.8 Wh kg−1 and remarkable cycling stability with a 4.3% deterioration of specific capacitance after 10 000 cycles. This work paves a new avenue to solve the two long‐standing significant challenges of MXene in the future. [ABSTRACT FROM AUTHOR]

Potassium‐ion hybrid capacitors have attracted increasing attention due to good energy density, high power density, and low cost. Ti3C2Tx‐MXene is considered as a promising anode material for K ion storage. However, undesirable stacking issues decrease its exposed area and breeds sluggish K ion transport. Herein, a facile spray‐lyophilization strategy is proposed to construct stacking‐resistant Ti3C2Tx with 3D structures. As‐prepared Ti3C2Tx hollow spheres/tubes present stack resistance, a large specific surface area, and a short ion diffusion pathway. When serving as an anode material, it shows enhanced capacity and thickness‐independent rate performance compared to 2D Ti3C2Tx. After 10 000 cycles, a specific capacity of 122 mAh g−1 is obtained at 1 A g−1. Systematic kinetics analyses demonstrate the significance of concentration polarization on the electrode's rate ability. Furthermore, a 3D Ti3C2Tx‖hierarchical porous activated carbon (HPAC) K‐ion hybrid capacitor is assembled and displays remarkable energy and power densities with energy retention of 100% after 10 000 cycles at 1 A g−1. Following this strategy, other 3D structures from nanosheets can also be obtained, such as 3D Ti3C2Tx microtubes and graphene oxide nanoscrolls. This study provides a viable approach to solve the stacking issues of 2D nanosheets to promote the application of 2D materials. [ABSTRACT FROM AUTHOR]

Lithium‐sulfur batteries attract lots of attention due to their high specific capacity, low cost, and environmental friendliness. However, the low sulfur utilization and short cycle life extremely hinder their application. Herein, we design and fabricate a three‐dimensional electrode by a simple filtration method to achieve a high‐sulfur loading. Biomass porous carbon is employed as a current collector, which not only enhances the electronic transport but also effectively limits the volume expansion of the active material. Meanwhile, an optimized carboxymethyl cellulose binder is chosen. The chemical bonding restricts the shuttle effect, leading to improved electrochemical performance. Under the ultrahigh sulfur load of 28 mg/cm2, the high capacity of 18 mAh/cm2 is still maintained, and stable cycling performance is obtained. This study demonstrates a viable strategy to develop promising lithium‐sulfur batteries with a three‐dimensional electrode, which promotes sulfur loading and electrochemical performance. [ABSTRACT FROM AUTHOR]

The development of electronic equipment and electric vehicles fields has brought enormous challenges to the energy storage sector. Electrode cost has become the biggest problem for large‐scale applications of lithium‐ion batteries. Herein, we use carbonized hemp rods as a current collector instead of expensive copper foil. Meanwhile, the three‐dimensional (3D) structure of carbonized hemp stalk (C‐hemp) has a large number of hollow channels, in which a large amount of Co3O4 nanowires are grown, providing an area specific capacity of 10 mAh/cm2. The battery exhibits a good cycle performance and keeps a stable capacity during 50 charge‐discharge cycles. At the same time, the carbon matrix provides an excellent 3D conductive network that combines with metal oxide nanorods to show an excellent rate performance. [ABSTRACT FROM AUTHOR]

Aqueous batteries have attracted increasing and extensive attention, owing to their high safety, low cost, and low toxicity. These factors have become increasingly important, given the current focus on the rapid development of green energy technologies. In particular, multivalent‐ion batteries are emerging as alternatives to lithium‐ion batteries. Unfortunately, magnesium and aluminum ions have high polarization strengths that are unfavorable for electrode materials. In contrast, calcium‐ion batteries successfully avoid the problem of high polarization. Herein, an aqueous calcium‐ion battery (CIBs) based on mesoporous silica SBA‐15 with a two‐dimensional hexagonal through‐hole structure is reported. The poly(3,4,9,10‐perylentetracarboxylic diimide) (PPTCDI) organic material supported on SBA‐15 is used as the anode and displays a capacity of 201 mAh g−1, with a stable cycling performance of 95 % capacity retention after 1500 cycles. SBA‐15@PPTCDI‖Ca2MnO4 aqueous CIBs demonstrate a high energy density of 130.6 Wh kg−1 in the cell voltage range from 0.0 to 1.8 V, with a high capacity and excellent cycling stability. As the anode material, SBA‐15@PPTCDI shows special bonding of redox electrons that leads to its highly stable performance, which paves the way for addressing the shortcomings of traditional organic electrode materials. The localization and delocalization of the redox electron offers additional voltage stability, which is another important advantage for practical applications. This study highlights the potential of organic electrode materials for applications in aqueous multivalent‐metal‐ion batteries. [ABSTRACT FROM AUTHOR]

A fast one‐step arc discharge exfoliation method is employed to synthesize Si/graphene composites by using a graphite rod filled with a mixture of Si powder and urea as a cathode. During the arc discharge process, the use of urea allows both the introduction of nitrogen atoms into the graphene and the uniform sealing of Si nanoparticles between the thin graphene sheets to occur simultaneously. The resulting N‐doped graphene nanosheets embedded with Si (Si@NG) can act as an electrode material for lithium‐ion batteries and delivers the reversible capacity of 1030 mAh g−1 with a current density of 200 mA g−1 over 100 cycles along with an outstanding coulombic efficiency of 96.84 %. The remarkable electrochemical rate capability performance can be owed to the multiple role of NG, which not only serves as a three‐dimensional conductive support, but also effectively limits the volume variation of Si nanoparticles. The approach proposed here is expected to be extended to the preparation of other alloy anode/graphene hybrids for lithium ion batteries. [ABSTRACT FROM AUTHOR]

Polydopamine modified reduced graphene oxides (PDA‐rGO) are synthesized by a facile dopamine polymerization reaction. As‐prepared PDA‐rGO shows a capable electrochemical performance as an electrode material for supercapacitors. A capacitance of 120 F g−1 is achieved at current density of 2 A g−1. PDA‐rGO also presents a superior cycling performance with capacitance retention of ∼99% after 10000 cycles. The remarkable electrochemical performance is attributed to the addition of PDA, which prevents the stacking of rGO and enhances the wettability of composite. Meanwhile, the rGO with high conductivity promise fast electronic transport. Polydopamine modified reduced graphene oxides (PDA‐rGO) are synthesized by a facile dopamine polymerization reaction. A capacitance of 120 F g−1 is achieved at current density of 2 A g−1. PDA‐rGO also presents a superior cycling performance with capacitance retention of ∼99% after 10000 cycles. The remarkable electrochemical performance is attributed to the addition of PDA, which prevents the stacking of rGO and enhances the wettability of composite. [ABSTRACT FROM AUTHOR]

Abstract: Hollow structures are considered as promising electrode materials. Their enhanced surface‐to‐volume ratio results in an increased contact area between the electrolyte and electrode and, thereby, a higher accessibility of active material. Here, a facile hydrothermal method is applied to synthesize hollow Cu2O spheres, assembled by well‐aligned nanofibers. Based on the investigation of the samples at different reaction times, a growing mechanism is proposed. Nano building‐blocks create porous channels within the shell, which could facilitate the transfer and shorten the transportation pathway for both ions and charge. The Cu2O with its unique structure displays a high specific capacitance of 1075 F g−1 at a current density of 5 mA cm−2, a remarkable rate capability of 82 %, and an excellent cycling property of nearly 100 % of the initial value remaining after 5000 charge‐discharge cycles. Moreover, the hollow Cu2O spheres are first used for the preparation of a positive electrode in an asymmetric supercapacitor, using carbon as a negative electrode. The device exhibits a high energy density of 44.7 Wh kg−1 at a power density of 420.2 W kg−1, and when the power density reaches values as high as 4201.7 W kg−1, an energy density of 16 Wh kg−1 is still attained. [ABSTRACT FROM AUTHOR]

Porous FeVO4 is prepared by hydrothermal method and further modified by coating with carbon to obtain FeVO4/C with a hierarchical pore structure. FeVO4/C is used as an anodic electrode in aqueous rechargeable magnesium-ion batteries. The FeVO4/C material not only has improved electrical conductivity as a result of the carbon coating layer, but also has an increased specific surface area as a result of the hierarchical pore structure, which is beneficial for magnesium-ion insertion/deinsertion. Therefore, an aqueous rechargeable magnesium-ion full battery is successfully constructed with FeVO4/C as the anode, Mg-OMS-1 (OMS=octahedral molecular sieves) as the cathode, and 1.0 mol L−1 MgSO4 as the electrolyte. The discharge capacity of the Mg-OMS-1//FeVO4/C aqueous battery is 58.9 mAh g−1 at a current density of 100 mA g−1; this value is obtained by calculating the total mass of two electrodes and the capacity retention rate of this device is 97.7 % after 100 cycles, with almost 100 % coulombic efficiency, which indicates that the system has a good electrochemical reversibility. Additionally, this system can achieve a high energy density of 70.4 Wh kg−1, which provides powerful evidence that an aqueous magnesium-ion battery is possible. [ABSTRACT FROM AUTHOR]

To bridge the gap of the alkali-metal-ion (Li or Na) batteries and supercapacitors, hybrid devices called capacitor batteries are being designed, which are adaptive for large-scale energy-storage systems. Two-dimensional transition-metal carbide materials (MXene) with high electronic conductivities have become capable electrode materials for supercapacitors. Herein, Ti3C2Tx synthesized by selectively etching the Al layer from the Ti3AlC2 presents a remarkable electrochemical performance as an electrode material for the supercapacitor with Li2SO4 or Na2SO4 aqueous electrolyte. It displays a capacitance of 243 F g−1 at a low current density of 100 mA g−1 with a capacitance retention of 95 % in the Li2SO4 electrolyte, and a capacitance of 150 F g−1 at a low current density of 200 mA g−1 with a capacitance retention of 95 % in the Na2SO4 electrolyte, which shows its potential application for capacitor batteries. Moreover, the LiMn2O4//Ti3C2Tx Li-ion capacitor battery and MnO2//Ti3C2Tx Na-ion capacitor battery are designed and assembled for the first time. Such rechargeable aqueous capacitor batteries display capable capacities, remarkable rate abilities, and excellent cycling performances, which further demonstrates that Ti3C2Tx is an outstanding capacitor-type electrode material for capacitor batteries. [ABSTRACT FROM AUTHOR]

For the first time, hierarchically porous carbon materials with a sandwich-like structure are synthesized through a facile and efficient tri-template approach. The hierarchically porous microstructures consist of abundant macropores and numerous micropores embedded into the crosslinked mesoporous walls. As a result, the obtained carbon material with a unique sandwich-like structure has a relatively high specific surface (1235 m2 g−1), large pore volume (1.30 cm3 g−1), and appropriate pore size distribution. These merits lead to a comparably high specific capacitance of 274.8 F g−1 at 0.2 A g−1 and satisfying rate performance (87.7 % retention from 1 to 20 A g−1). More importantly, the symmetric supercapacitor with two identical as-prepared carbon samples shows a superior energy density of 18.47 Wh kg−1 at a power density of 179.9 W kg−1. The asymmetric supercapacitor based on as-obtained carbon sample and its composite with manganese dioxide (MnO2) can reach up to an energy density of 25.93 Wh kg−1 at a power density of 199.9 W kg−1. Therefore, these unique carbon material open a promising prospect for future development and utilization in the field of energy storage. [ABSTRACT FROM AUTHOR]

Developing advanced supercapacitors with both high areal and volumetric energy densities remains challenging. In this work, self‐supported, compact carbon composite electrodes are designed with tunable thickness using 3D printing technology for high‐energy‐density supercapacitors. The 3D carbon composite electrodes are composed of the closely stacked and aligned active carbon/carbon nanotube/reduced graphene oxide (AC/CNT/rGO) composite filaments. The AC microparticles are uniformly embedded in the wrinkled CNT/rGO conductive networks without using polymer binders, which contributes to the formation of abundant open and hierarchical pores. The 3D‐printed ultrathick AC/CNT/rGO composite electrode (ten layers) features high areal and volumetric mass loadings of 56.9 mg cm−2 and 256.3 mg cm−3, respectively. The symmetric cell assembled with the 3D‐printed thin GO separator and ultrathick AC/CNT/rGO electrodes can possess both high areal and volumetric capacitances of 4.56 F cm−2 and 10.28 F cm−3, respectively. Correspondingly, the assembled ultrathick and compact symmetric cell achieves high areal and volumetric energy densities of 0.63 mWh cm−2 and 1.43 mWh cm−3, respectively. The all‐component extrusion‐based 3D printing offers a promising strategy for the fabrication of multiscale and multidimensional structures of various high‐energy‐density electrochemical energy storage devices. The all‐graphene‐oxide (GO)‐based symmetric supercapacitor is assembled with a thin GO separator and compact active carbon/carbon nanotube/reduced graphene oxide composite electrodes with tunable thickness, which are fabricated using the advanced extrusion‐based 3D printing technology. The 3D‐printed ultrathick and compact symmetric supercapacitor with a high mass loading can achieve both high areal and volumetric energy densities. [ABSTRACT FROM AUTHOR]