Search

Water-sensitive papers (WSPs), as an artificial target, have been generally used to evaluate spray quality in pesticide applications. Though many tools were available to analyze WSPs, they were not effective in processing the presented overlapping droplets, which prevented accurate quantification of spray quality. Here, a novel methodology was proposed to analyze WSPs, focusing on the segmentation of overlapping droplets based on concave point detection and ellipse fitting. Up to 553 WSPs obtained from field trials in apple trees were used to validate this methodology. A high overall segmentation accuracy of 77.8% was achieved for the WSPs with coverage below 25%, which allowed to precisely characterize the corresponding deposition pattern. A universal linear relationship was observed between the droplet density and coverage, independent of the sprayer and canopy characteristics. In addition, the droplet size distributions for all spray applications showed a similar trend. As the proposed methodology was not effective to segment the complex overlapping spots on the WSP with high coverage (>25%), simulated WSPs were generated to estimate the deposition pattern of high coverage based on the droplet size distribution deposited on the WSPs with low coverage. A linear relationship with a much higher slope was observed between droplet density and coverage for the high deposition, which enabled an approximate estimation of the corresponding droplet density. In general, the proposed approaches allowed to obtain more accurate spray quality indicators from the WSP collectors and could be widely used for spray application evaluation to promote precision spraying. • A novel approach was proposed to analyze WSPs with the split of overlapping droplets. • A high segmentation accuracy of 77.8% was observed for the WSPs with low coverage. • A linear relationship was observed between the droplet density and spray coverage. • The applied droplet pattern showed a remarkable effect on the spray distribution. • The droplet density at high coverage was estimated based on the computer simulation. [ABSTRACT FROM AUTHOR]

Pinus taeda is a principal conifer tree species and has long been used in forest plantations in Southern Brazil. At the same time, experiments have been carried out in order to determine the wood productivity concerning the economic, social and sustainable forest management practices. In that sense, the organic fertilizers, such as the biosolid residues from pulp and paper industries, are one of the alternatives to achieve this sustainability. Nevertheless, few studies addressing this objective have been reported in Brazil. This study aimed to analyze the growth responses of loblolly pine trees treated with different doses of composted pulp-mill sludge and to propose a management guide based on a wood production simulation. A randomized block design with four replicates for every six treatments - control, 20, 40, 60, 80 and 100 t ha −1 of composted pulp-mill sludge - were carried out in an experimental plantation located in Arapoti, Paraná state, Brazil. Ten 17 year-old-trees for each treatment were selected, the stem variables were analyzed and the stand wood productivity for the optimal dosage was simulated. The trees were significantly influenced by the application of the composted pulp-mill sludge, increasing up to 24, 37 and 127% in stem diameter, height and volume, respectively, and the rotation of the pine plantation control and treated stands was 33 and 21 years, respectively. The forest management applied for a 21-year harvesting cycle (thinning at 7 and 13 years) with 84 t ha −1 of composted pulp-mill sludge resulted in a wood productivity of 11.9 m 3 ha −1 or 5.04 Mg ha −1 per year. The results confirm the potential application of pulp-mill sludge as a fertilizer to improve the wood productivity of forest plantations established in poor-nutrient sites. Also, the forest management plans, using the guide proposed, could be replicated in loblolly pine and other tree species plantations according to the end use of wood. [ABSTRACT FROM AUTHOR]

Hydrothermal treatment of sludge within the pulp and paper industry can have a wide range of possible reactor solid loads for different sludge types. The objectives of this work were to determine the effect of reactor temperature and solid load on the properties of sludge hydrochar and to simulate hydrothermal treatment of sludge within a pulp and paper mill. Laboratory experiments were first performed within reactor temperature and solid load ranges of 180–260 °C and 10–50%, respectively, and the effects of sludge treatment were determined by comparing parallel mill-scale simulations. Based on the results, both reactor temperature and solid load had a statistically significant effect on the solid, ash, carbon and energy yields of sludge hydrochar. Increasing solid load minimized carbon dissolution to the liquid phase and increased the solid and energy yield of the attained hydrochar. According to mill-scale simulations in a 9 m 3 batch reactor, treating primary sludge alone produced an energy surplus of 22–36 GJ through char incineration, decreasing to 12–22 GJ and 3.4–9.1 GJ for mixed and secondary sludge, respectively. Mixing primary and secondary sludge reduced the overall energy surplus by 2–8% compared with treating the sludge streams separately in two reactors. [ABSTRACT FROM AUTHOR]

Highlights • Paper-based thin sample layer ion transfer voltammetry was realized. • Linear scan voltammetry was chosen to investigate the electrochemical behavior. • Electrochemical behavior are compared to numerical simulation. • Background corrections can be used to eliminate undesired interference. Abstract We report here on paper-supported thin sample layer voltammetry for the determination of ions. To achieve this goal, a simple setup for the coupling of a commercially available electrode to a silver rod electrode was designed and evaluated for paper-supported thin-layer voltammetry. Linear scan ion transfer voltammetry was explored here for ion-selective membranes doped with an ionophore. The ion-transfer processes and electrochemical behaviors of the system are here evaluated and confirmed by numerical simulation. In the proof-of-concept experiments described, the ions tetrabutylammonium chloride (TBA+) and potassium (K+) were studied as model analytes at membranes without and with ionophore, respectively. A linear relationship from 0.1 mM to 1.0 mM K+ was obtained between the charge and ion concentration. The coexistence of background sodium ions did not give appreciable interference, but the background wave was not completely isolated from the analyte wave, as also confirmed by the model. The methodology was successfully demonstrated for determination of K+ in mineral water. It is anticipated that this paper-supported thin-layer detection approach may provide an attractive readout protocol for disposable paper-based analytical devices as the methodology does not place strict demands on reference electrode performance. [ABSTRACT FROM AUTHOR]

Abstract A number of problems associated with dimensional stability of paper products have to do with hygroexpansion in response to changes in humidity or moisture content. The main underlying mechanism of hygroexpansion in paper is the effect of the change of fiber cross-sections transferred through fiber bonds. In fact, the transverse expansion of fibers can be an order of magnitude greater than the longitudinal expansion. Addressing such problems using modeling on the microscale is associated with large computational costs since both the bonds and the fibers need to be resolved. We present a method for modeling the hygro or thermal expansion of interconnected fiber networks modeled with beam elements and connected through beam-to-beam contact. Being a line structure, beams can only support pointwise contact, which poses a challenge for modeling the force transfer induced by the deformation of the cross-sections at the contact point. The idea of implementing the stress transfer is to use a concurrent multiscale approach in which the bond level is resolved in detail using the configuration of the fibers and the computed strains are passed over to the beam elements. We verify and prove the applicability of this approach by comparing it with continuum models. We demonstrate the advantage of using this approach in terms of its tremendous saving in time. The use of beam models for modeling the hygro- or thermal expansion of fiber networks enables considering relevant sizes in the problems involving dimensional stability, in particular those associated with embedded inhomogeneities. We will show the applicability of the model by providing insights into published experimental observations on the hygroexpansion properties of paper products. Finally, we will demonstrate that the use of a 2D model to simulate the inter-fiber bonds in a network, not only leads to underestimation of out-of-plane deformations, but also to overestimation of the contribution of the transverse deformation of fibers to the in-plane dimensional change of the network. [ABSTRACT FROM AUTHOR]

Some errors exist in the above paper. [ABSTRACT FROM AUTHOR]

Thin-walled tubular deployable composite boom (DCB) has gained significant attention due to its lightweight, simple structure and high packaging efficiency. The experimental and numerical simulation methods were employed in this paper to investigate the folding behavior of the DCB. Using T700/epoxy unidirectional reinforced prepreg as raw material, DCB specimens were prepared by the vacuum bag method. To complete the folding experiments of DCB specimens, a folding mechanism was designed and manufactured. Folding experiments of DCB specimens were conducted and folding moment versus rotational displacement curves were measured. In addition, a Finite Element Model (FEM) was established to predict the folding behavior of the DCB. Different failure criteria were considered in the numerical analysis, including the Tsai‐Hill criterion and maximum stress criterion. Prediction results using the FEM were compared with experimental results, and both sets of results were in good agreement. It is shown that the DCB can achieve the folding function without failure. The research results in this paper are of great significance to the practical engineering application of the DCB. [Display omitted] • Six tubular deployable composite boom specimens and a precise folding mechanism were designed and prepared. • Folding experiments were conducted to measure the folding moment and rotational displacement curves. • A finite element model for predicting the folding behavior of the tubular deployable composite boom was established. [ABSTRACT FROM AUTHOR]

Aramid paper honeycomb cores have been extensively used in lightweight structures. However, compressive properties of the paper, which are important for predicting the mechanical behaviors of honeycomb cores, can hardly be accurately measured due to the weak out-of-plane bending stiffness. Here, we propose an experimental method to characterize the in-plane compressive properties of the paper, in which the paper is processed into a laminate by the adhesive between layers to prevent the out-of-plane buckling. We also conducted a meso-mechanics model to analyze the compressive behavior. The compressive modulus of the hybrid paper obtained from our proposed method is basically identical to the tensile modulus, and the strength is much larger than previous estimations due to effectively avoiding the buckling. Then the compressive properties are used in numerical simulations to study the compressive properties of hybrid paper honeycombs, and the simulation calculated compressive modulus and strength agree well with experimental results, which verifies the accuracy of our method. This meso-mechanics-based characterization method can be applied to other types of paper and paper-like materials as well. • A meso-mechanics-based experimental characterization method for paper is proposed. • The method can characterize the in-plane compressive properties of paper accurately. • The tested paper properties can give a better prediction of honeycomb properties. [ABSTRACT FROM AUTHOR]

Paper (Maniar and Bhattacharyay, 2021) introduces a discrete random-walk (RW) model with a site dependent waiting time and an external force i.e. a site dependent drift. The RW is compared with a Smoluchowski equation in continuous space and time with space dependent diffusivity and space dependent damping. Using numerical simulations in Maniar and Bhattacharyay (2021) it is shown that the equilibrium distribution satisfies locally the Stokes–Einstein relation i.e. there is a constant temperature in the whole system. Here we show that the result can be recovered analytically with a continuous limit in the RW master equation. Moreover, we evidence that the RW model should be carefully defined in order to satisfy locally Stokes–Einstein relation, indeed a different definition of the discrete RW process describes a system that satisfies the Smoluchowski equation with constant damping, where the temperature is not uniform. [ABSTRACT FROM AUTHOR]

The future use of eddy resolving simulations (ERS) such as Large Eddy Simulation (LES), Direct Numerical Simulation (DNS) and related approaches in aerospace is explored. The turbulence modeling requirements with respect to aeroengines and aircraft is contrasted. For the latter, higher Reynolds numbers are more prevalent and this especially gives rise to the need for the hybridization of ERS methods with Reynolds Averaged Navier–Stokes (RANS) approaches. Zones where future use of pure ERS methods is now possible and those where hybridizations with RANS will be needed is outlined. The major focus is the aeroengine for which the component scales are much smaller. This gives rise to generally more benign Reynolds numbers. The use of eddy resolving methods in a wide range of zones in an aeroengine is discussed and the potential benefits and also cost drawbacks with such approaches noted. The tension when using such computationally intensive calculations in an area where the coupling of components and even the airframe and engine is becoming increasingly important is explored. Also, the numerical methods and meshing requirements are considered and the implications of ERS methods for future numerical algorithms. It is postulated that such simulations are ready now for niche uses in industry. However, to perform the scale of simulations that industry requires, to meet pressing environmental needs, challenges remain. For example, there is the need to develop optimal numerical methods that both map to the accuracy requirements for ERS and also future computer architectures. [ABSTRACT FROM AUTHOR]

The program code in the paper “Computer simulation of Talbot phenomenon using the Fresnel integrals approach” ( http://dx.doi.org/10.1016/j.ijleo.2016.01.175 ) is incompatible with MATLAB 7 and MATLAB 8. According to MATLAB documentation mfun function will be removed in a future release, besides str2double function is used. [ABSTRACT FROM AUTHOR]

This paper presents a reply to the discussion of the paper “Numerical simulation of moisture transport in concrete based on a pore size distribution model” by Q. Zeng and S.L. Xu. [ABSTRACT FROM AUTHOR]

• kinetic description of a binary game • quasi-invariant limit • numerical simulations This article studies the kinetic dynamics of the rock-paper-scissors binary game. We first prove existence and uniqueness of the solution of the kinetic equation and subsequently we prove the rigorous derivation of the quasi-invariant limit for two meaningful choices of the domain of definition of the independent variables. We notice that the domain of definition of the problem plays a crucial role and heavily influences the behavior of the solution. The rigorous proof of the relaxation limit does not need the use of entropy estimates for ensuring compactness. [ABSTRACT FROM AUTHOR]

The parameter L 0 with a unit length (=1.0 m) was omitted in our paper, and the unit of loading speed s 1 and the expression of parameter c 7 were not shown, which result in that the dimensions of shear strain and shear strain rate shown in Eq.(16) were misinterpreted. In this response paper, we added the L 0 in the expressions of parameters c 6 and q , and explained the unit of s 1 , as well as gave the expression for the c 7. The addition of L 0 do not change the simulation results and conclusions of our paper. [ABSTRACT FROM AUTHOR]

In the present comment, the results of recently published by Li Shu and Yonglin Ju "Numerical Study on the Condensation Characteristics of Various Refrigerants Outside a Horizontal Plain Tube at Low Temperatures" in International Journal of Thermal Sciences 2022 are discussed. It is shown that one of the conclusions of the work that "at low saturation temperatures, the periodic-averaged heat transfer coefficient in the numerical simulation is lower than that calculated with Nusselt's equation, especially at large wall subcooling", is not supported by the results of simulation performed by the author of this comment. [ABSTRACT FROM AUTHOR]

Older adults exhibit increased gait variability that is associated with fall history and predicts future falls. It is not known to what extent this increased variability results from increased physiological noise versus a decreased ability to regulate walking movements. To "walk", a person must move a finite distance in finite time, making stride length (Ln) and time (Tn) the fundamental stride variables to define forward walking. Multiple age-related physiological changes increase neuromotor noise, increasing gait variability. If older adults also alter how they regulate their stride variables, this could further exacerbate that variability. We previously developed a Goal Equivalent Manifold (GEM) computational framework specifically to separate these causes of variability. Here, we apply this framework to identify how both young and high-functioning healthy older adults regulate stepping from each stride to the next. Healthy older adults exhibited increased gait variability, independent of walking speed. However, despite this, these healthy older adults also concurrently exhibited no differences (all p>0.50) from young adults either in how their stride variability was distributed relative to the GEM or in how they regulated, from stride to stride, either their basic stepping variables or deviations relative to the GEM. Using a validated computational model, we found these experimental findings were consistent with increased gait variability arising solely from increased neuromotor noise, and not from changes in stride-to-stride control. Thus, age-related increased gait variability likely precedes impaired stepping control. This suggests these changes may in turn precede increased fall risk. [ABSTRACT FROM AUTHOR]

The Lennard-Jones (LJ) fluid, named after mathematician-physicist-chemist Sir John Lennard-Jones (1894–1954), occupies a special place among fluids. It is an ideal entity, defined as the fluid whose particles interact according to the Lennard-Jones potential. This paper expounds the history of the LJ fluid to throw light on the tensions between theory and computational practice. The paper argues for the following claims. Firstly, the computational approach—even prior to the computer—pragmatically aims at prediction, not truth. Secondly, computer simulation methods, especially "molecular dynamics" (MD), triggered a change in epistemology. Now, simulated model fluids became targets of investigation in their own right. The urge for prediction turned the LJ fluid into the most investigated fluid in engineering thermodynamics. Thirdly, MD took a huge upswing in the 1990s, due to exploratory options in simulation. We discuss how, under these conditions, predictive success might be fraught with problems of reproducibility. [ABSTRACT FROM AUTHOR]

Particle swarm optimization (PSO) is a widely adopted, rapid, efficient, and computer-friendly technique for optimization in various fields, including computer science, engineering, and mathematical modelling. In this paper, the nonlinear Schrodinger (NLS) equation has been solved numerically, which leads to soliton-type solutions, by utilizing the "Exponential cubic B-spline differential quadrature method (Expo-MCB-DQM) with PSO". The exponential cubic B-spline basis functions involve a parameter that must be assigned a value to find the numerical solutions. Until now, the value of a parameter had been determined by the hit-and-trial approach, which leads to unstable results. By employing the PSO technique, the optimal value of the parameter is determined, which enhances the accuracy of the numerical solutions. This study introduces an innovative combination of Expo-MCB-DQM with PSO, which is an innovative combination that optimizes the parameters in the basis function, leading to improved outcomes. To validate the authenticity and effectiveness of this methodology, it has been applied to two problems to present the numerical results in comparison with the exact solution. Additionally, the paper provides insightful discussions on the significant application of the NLS equation in optical fiber communication. [ABSTRACT FROM AUTHOR]

We suggest a method to identify the suitability of a chosen indoor environment for paper material conservation in historical libraries. Our approach is based on two steps: numerical simulation for solving the air velocity, moisture and temperature fields, and then post-processing indexes evaluation to assess how the indoor microclimatic conditions can be favourable or not to the growth and development of microorganisms responsible for paper deterioration. A real case study was analysed in two different conditions: one the present situation and the other proposed by the authors with a HVAC system assuring controlled air temperature and RH levels. Numerical models, validated by experimental data published in previous works, were used to carry out microclimatic results. Starting from these results, some indexes suggested by the scientific literature were computed to check the suitability of the indoor environment for preserving a library heritage. Boolean parameters were also deduced from the combination of microclimatic factors favouring the growth of microorganisms responsible for paper material deterioration. Our research can provide a methodological approach that predictively allows one to know when, where and how the processes responsible for indoor microorganism activity can find the microclimatic conditions for their kick-off and triggering, and then their areas of potential growth. The proposed method highlights the main causes of the deterioration processes connected to building thermo-physics. Simulation results turned out to be a fundamental approach to identify the risky zones and potential areas of triggering deterioration processes of all the materials present. [ABSTRACT FROM AUTHOR]

The Shuiyindong gold mine in Guizhou is used as a case study in this paper to study patterns of dust pollution occurring with traditional electric-rake operation. In particular, the study uses the northern quarry of the twenty-third line in the first middle section of the second mining area and establishes a three-dimensional simulation model of equal size. It uses Computational Fluid Dynamics (CFD) to simulate and analyse the airflow traces and distribution of dust concentration in the relevant roadway during each stage of the electric-rake operation. The simulation results show that the airflow in the working roadway has a spiral movement and produces reverse dirty-wind circulation towards the end. Dust flows out of the working roadway from the 8th second of operation, and dust concentration reaches a peak in the working roadway at the 12th second of operation at an average dust concentration of 37.5 mg/m³. The dust concentration drops rapidly from the 120th second and reaches the maximum dust concentration permitted for operation at the 180th second of operation. The validity of the simulation is tested by comparing the actual measured data at the site with the simulation results. Finally, the simulation results are analysed using violent Python, and the solution is used to divide the roadway into areas according to the human breathing range. The paper analyses the distribution of dust concentration at an average human breathing height, providing an established theoretical basis for dust-control work in mines. [Display omitted] [ABSTRACT FROM AUTHOR]

Volatile Organic Compounds (VOCs) are widely concerned owing to their serious harm to the ecological environment and human health. In this paper, the adsorption effect of VOCs on a new type of swirling fluidized bed was studied from two aspects of numerical simulation and experimental research, which expanded the application of the device in the field of VOC removal. It was found that the adsorption efficiency of activated carbon in the cyclone fluidized bed was inversely proportional to the inlet concentration and the height of the spinning core column, and was proportional to the mass of the adsorbent and the diameter of the spinning core column. When SAC-3 activated carbon and cyclone fluidized bed S 16–22 were selected, the highest adsorption efficiency was up to 100%, and the damage rate of activated carbon was not more than 3%. The simulation results showed that the maximum axial velocity and the maximum tangential velocity existed in the annular space. The axial velocity and tangential velocity on the cross-section first increased and then decreased with the increase of the radius. The axial velocity was proportional to the flow rate, the diameter, and height of the spinning core. The tangential velocity first increased and then decreased with the increase of the flow rate, diameter, and height of the spinning core. The overall pressure increased with the increase of the flow rate, the pressure increased with the increase of the radius in the cross-section, and the pressure decreased rapidly with the increase of the height in the axial direction. In this paper, a new type of cyclone fluidized bed is used to replace the existing fixed bed and carry bed system, and the optimal activated carbon, the best working conditions, and the best rotary fluidized bed structure are screened by the cyclone fluidized bed experiment. [Display omitted] • A new cyclone fluidized bed was developed for the adsorption treatment of VOC. • CFD method was used to study the internal flow field characteristics. • The best experimental conditions are explored. • The cyclone fluidized bed can effectively treat VOC with sustainable operation. [ABSTRACT FROM AUTHOR]

In this paper, a distributed bearing-based formation control scheme with finite-time convergency is proposed for multiple underactuated surface vessels (USVs). By virtue of the guide point-based model transformation method, the dimension of underactuated tracking error dynamics can be reduced from three to two. This allows us to convert the actuator model to a fully form that matches dimension-reduced tracking error dynamics. Further, to reduce the computation complexity, a finite-time recruited filter is designed according to first-order Levant differentiator. At meanwhile, auxiliary error compensation signals are introduced to address unknowns stemming from filter process and system dynamics. Since merely relative-distances and inner bearings are utilized in the proposed bearing-based formation approaches, the proposed control scheme provides a feasible solution to achieve formation control under body-fixed frame. Finally, theoretical analysis and numerical simulations are presented to demonstrate the efficacy. • Bearing-based finite-time formation control. • Underactuated surface vessels. • Levant differentiator. • Command filtered backstepping with error compensation signals and compensated errors. [ABSTRACT FROM AUTHOR]

Erratum to "on obtaining double-layer capacitance and potential of zero charge from voltammetry" [J. Electroanal. In the paper referred to, there are two typographical errors in Eq. (3), which is now corrected to, Ji= 1+ 22X 41- j/=inj ni X+ ni j/=i nj X+zini1- jnj U X These errors did not flow into the Matlab code, therefore, the numerical simulation results need no change. Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. [Extracted from the article]

Metal heat pipe evacuated collector tube (ECT) suffer from cracks in the joint between the glass outer layer and the metal heat pipe due to the large difference in thermal expansion coefficients of glass and metal, resulting in non-industrialization. In this paper, the metal heat pipe is replaced with a glass heat pipe to form an all-glass heat pipe ECT to address the air-tight sealing problem. The results show that the thermal stress at the seal joint is approximately zero, below 0.279 MPa, far below than the bearing range of 40-120 MPa. At the same time, it was also shows that by adding a reflective film to the lower half of the outer layer glass, the optical efficiency was increased by 0.17 %. The energy output in the quasi-equilibrium state is 87 W, which is 8 W higher in the simulation. Water-vapor directly reaches the condensation section to reduce the formation of vortices under conditions where it absorbs sufficient energy to overcome its own gravity and ambient pressure, thus reducing heat loss and increasing thermal efficiency. Fig. 1. All-glass heat pipe vacuumed collector. [Display omitted] • A metal heat pipe is replaced with glass to form an all-glass heat pipe evacuated collector tube. • Maximum thermal stress of 0.279 MPa is well below than the bearing range of 40–120 MPa. • All-glass structure fully copes with the transient local heating changes. • Optical efficiency is increased by 0.17% by the addition of the reflective film. • Yielding an energy output of 87 W in the quasi-thermal equilibrium state. Metal heat pipe evacuated collector tube (ECT) suffer from cracks in the joint between the glass outer layer and the metal heat pipe due to the large difference in thermal expansion coefficients of glass and metal, resulting in non-industrialization. In this paper, the metal heat pipe is replaced with a glass heat pipe to form an all-glass heat pipe ECT to address the air-tight sealing problem, and a reflective film was added to the lower part of the outer tube to improve energy. According to these results, the thermal stress of 0.279 MPa is well below the bearing range of 40–120 MPa, and the maximum thermal strain of 0.175 mm/mm is also far less than the affordable value of 120 mm/mm, inducting the all-glass structure fully copes with the transient local heating changes. The optical efficiency is increased by 0.17 % by the addition of the reflective film, and yielding an energy output of 87 W and a maximum volume fraction of 4.8 % for liquid–water in the quasi-thermal equilibrium state. At the same time, the evaporation operating speed of the vapor can be increased by improving the solar radiation flux density and reducing thermal losses, and optimizing the multi-level and cross-scale vapor vortices can also improve the convective heat transfer rate, so they are future directions for development. However, there are the limitations of decreasing the thermal conductivity and increases the resistance due to the heat pipe conversion from metal to glass. [ABSTRACT FROM AUTHOR]

[Display omitted] • A novel fractional-order hyperchaotic system is investigated. • Existence of chaotic attractors just in the fractional-order case, in this system, are reported. • Bifurcation diagrams and corresponding Lyapunov spectrum are computed. • The work reports the first example that shows existence of chaotic attractors that exist only in fractional-order case. Studying chaotic dynamics in fractional- and integer-order dynamical systems has let researchers understand and predict the mechanisms of related non-linear phenomena. Phase transitions between the fractional- and integer-order cases is one of the main problems that have been extensively examined by scientists, economists, and engineers. This paper reports the existence of chaotic attractors that exist only in the fractional-order case when using the specific selection of parameter values in a new hyperchaotic (Matouk's) system. This paper discusses stability analysis of the steady-state solutions, existence of hidden chaotic attractors and self-excited chaotic attractors. The results are supported by computing basin sets of attractions, bifurcation diagrams and the Lyapunov exponent spectrum. These tools verify the existence of chaotic dynamics in the fractional-order case; however, the corresponding integer-order counterpart exhibits quasi-periodic dynamics when using the same choice of initial conditions and parameter set. Projective synchronization via non-linear controllers is also achieved between drive and response states of the hidden chaotic attractors of the fractional Matouk's system. Dynamical analysis and computer simulation results verify that the chaotic attractors exist only in the fractional-order case when using the specific selection of parameter values in the Matouk's hyperchaotic system. An example of the existence of hidden and self-excited chaotic attractors that appears only in the fractional-order case is discussed. So, the obtained results give the first example that shows chaotic states are not necessarily transmitted between fractional- and integer-order dynamical systems when using a specific selection of parameter values. Chaos synchronization using the hidden attractors' manifolds provides new challenges in chaos-based applications to technology and industrial fields. [ABSTRACT FROM AUTHOR]

The processes occurring in near and far space have a significant impact on the safety of space flights. Processes such as explosions of supernovae and relativistic jets have a particularly great impact. They arise in quasars, black holes, protostars. Often such structures are observed during the formation of new stars. Such jets have a great impact on the safety of space flights. For example, there is currently no radiation shelter on the International Space Station, so astronauts are at serious risk of getting radiation sickness. In addition, the skin of the orbital station modules consists of aluminum, which accumulates secondary radiation. The formation process of new star systems is the result of complex processes that occur in interstellar gas. These processes include nonlinear interactions of turbulence, gravity, collisions of molecular clouds with each other, as well as rotation and several other factors. The evolution of the formation of superdense substance begins from the moment when it gathers in turbulent flows or is formed by supersonic collisions of molecular clouds with each other, or are formed during the intereaction of molecular clouds with supersonic waves, which are formed during the explosions of supernovae, until the moment when these superdense areas reach the prestellar density. Further, depending on several factors, these superdense formations either collapse or disintegrate and return to the interstellar medium. The analysis of observations allows to conclude that a significant part of the molecular clouds is not gravitationally bound. These conclusions are made based on the virial theorem, which expresses the connection between gravitational and kinetic energy. In this paper, a simulation of large molecular clouds collision in a three-dimensional formulation on ultra-high-resolution grids is carried out. Execution of such calculations requires a lot of computer capacity. The paper presents the results of computer modeling of large-scale processes of filament formation and superdense, gravitationally coupled structurally parallel computation clusters with hybrid architecture. Parallel simulation on supercomputers was conducted with author's software, which uses a modified second-order Godunov method of accuracy of the Total Variation Diminishion type. Calculations were conducted on grids that contain more than one billion cells (1024 × 1024 × 1024). The gravitational potential is calculated on graphic processors. To refine the calculations, the method of adaptive refinement of the AMR grid is used. Simulation results are presented for cases of frontal collision of two molecular clouds, which density is distributed along the radius according to certain laws. • The processes of formation of new stellar systems are studied in this work in 3D simulation. • Appearance of clumps and filaments is discussed. • Morphing of high compression clumps set in possible stars formation zone is discussed. • The calculation program is based on a modified scheme of a high order of accuracy. [ABSTRACT FROM AUTHOR]

The distributed H ∞ consensus problem for heterogeneous multi-agent systems with nonconvex constraints is investigated in this paper. To deal with the coexistence of nonconvex constraints and disturbances, our main analysis is to transform the original system into a reduced-order system so as to use the H ∞ control theory to show the achievement of consensus with a desired H ∞ performance while the inputs of all agents constrained in the nonconvex sets. Numerical simulations verify the results in this paper. • Consensus problem for heterogeneous multi-agent system is studied. • The control inputs of all agents stay in a nonconvex set. • A new distributed H ∞ control algorithm has been developed. [ABSTRACT FROM AUTHOR]

Fractional calculus has become a potent tool for simulating the complexity of interactions in tumor-immune system dynamics. This paper investigates the existence and uniqueness of its approximation solutions of a fractional model of tumor-immune surveillance. This analysis is essential for proving the validity and dependability of the model and provides a more in-depth understanding of the dynamics of the tumor-immune surveillance system. Second, we examine the fractional model's numerical features. We utilize a numerical technique called the Laplace residual power series method to address the equations' complexity and nonlinearity. By defining the answers as a fractional power series, this method enables us to efficiently approximate the solutions. The use of this technique enables us to investigate the temporal evolution of the tumor-immune system, offering important insights into the stability and behavior of the system. We assess the effectiveness of the Laplace residual power series method in locating approximations through a series of thorough numerical simulations. To ensure the correctness and dependability of our method, we compare the numerical findings whenever possible with well-known analytical solutions. [ABSTRACT FROM AUTHOR]

In order to understand and master the diffusion mechanism and spatial concentration distribution of hydrogen leakage in the engine room, this paper studies the diffusion behavior and concentration distribution of hydrogen under the coupling effect of multiple factors, and further explores the optimal installation location of the sensors. The results indicate that when the ventilation rate increases by 1, 2, and 3 times, the diffusion volume of hydrogen decreases by about 0.4, 0.5, and 0.6 times. The harm of the increase in leakage diameter is greater than the leakage pressure. And the temperature has a greater impact on the hydrogen volume fraction in areas below 4 % and a smaller impact on areas above 4 %. In this environment, the sensors should be installed at or above 5.5 m in the rear of the engine room and above the axis of the hydrogen transport pipeline interface, valves and other places prone to leakage. • Taking a ship engine room as the research object. • The influence of various factors on hydrogen distribution is compared. • The spatial concentration distribution of hydrogen leakage is analyzed. • Explored the installation position of the sensors. [ABSTRACT FROM AUTHOR]

This paper proposes a method to describe the bi-modular behavior of quasi-brittle materials. The approach is based on using multiple loading functions that are associated with the stress state of the material point. The model also includes degradation laws that control the evolution of the internal variables under tension and compression, which allows the representation of the material response with fidelity. The following approach outlines an objective methodology for improving classical models and provides a theoretical framework for developing new constitutive models. This work also presents an updated version of the Mazars damage model, with improved material parametrization through multiple damage laws. Similarly, the modified von Mises model has been extended to include different functions for damage evolution, combining exponential and continuum polynomial laws for tension and compression. A third model was developed to showcase the full potential of the proposed formulation. This model formulates the Lemaitre and Chaboche criterion, typically used for ductile materials, to describe quasi-brittle materials. The model provides a comprehensive characterization of the tension and compression behavior by utilizing various loading functions and multiple damage laws. Numerical simulations of experimental benchmarks are presented to show the performance of the proposal, including a nonlocal approach to avoid strain localization and mesh dependency problems. • A formulation to represent simply the bi-modularity of quasi-brittle materials by isotropic damage models is presented. • The proposal provides versatility to prescribe any damage law, especially with fill constitutive parameters. • The strategy is applied to classical models present in literature providing an enhancement of the model behavior. • The approach can be extended and applied to other models presented in the literature. [ABSTRACT FROM AUTHOR]

This paper presents a numerical study of counterflow methane/n-heptane dual fuel flames, investigating the influence of pressure on flame structure and NO generation characteristics. The results demonstrate that, as pressure increases, the peak temperature and heat release rate of the flame increase, while the NO emission index decreases. The prompt NO emission index experiences a monotonic reduction as pressure increases, while the thermal NO emission index initially increases and then decreases. NO emission index via reburn route displays non-monotonicity with increasing pressure. Elevated pressure induces a decline in the mole fraction of radicals (CH, CH 2 and HCCO) crucial for prompt NO formation, consequently suppressing the formation of prompt NO. The principal reaction responsible for the consumption of reburn NO at lower pressures is HCCO+NO CO+HCNO, whereas the primary reaction for generating reburn NO is H+HNO H 2 +NO. However, at higher pressures, the reaction H+HNO H 2 +NO takes precedence as the dominant reaction consuming NO. • NO emission index decreases with increasing pressure. • Sensitivity analysis of NO generation under different pressures is conducted. • The formation routes of NO under different pressures are identified and analyzed. • The primary NO formation route changes from prompt to thermal as pressure rises. [ABSTRACT FROM AUTHOR]

• An optimal nutation reduction method based on a flexible contactor is proposed. • A highly efficient data-driven model is established to describe the contact process. • The nutation of a tumbling satellite can be reduced efficiently in the early stage of the de-tumbling tasks. Stabilizing tumbling satellites is a crucial step in ensuring safe on-orbit capture. A new de-tumbling method has been proposed that uses a flexible device, such as a brush or rod, to make contact with the target object and avoid potential collisions. However, this method faces two challenges: (i) The complex rotary motion makes it very difficult to determine the contact position on the target satellite, which is crucial to reduce nutation during de-tumbling. (ii) The conventional finite-element-based dynamic model of the flexible contactor is high-dimensional, leading to unacceptable computing time for on-orbit simulation. To address these problems, this paper proposes an optimal method to efficiently reduce the nutation by predicting the initial contact position for each contact process. Additionally, a fast computation model of the de-tumbling system is established based on a data-driven approach to support real-time prediction. Finally, numerical simulations are conducted to demonstrate the effectiveness and high efficiency of the proposed method. [ABSTRACT FROM AUTHOR]

This paper mainly studies the high-order stable numerical solutions of the time-space fractional diffusion equation. The Fourier spectral method is used for discretization in space and the Spectral Deferred Correction (SDC) method is used for numerical solutions in time. Therefore, a high-precision numerical discretization scheme for solving the fractional diffusion equation is obtained, and the convergence and stability of the scheme are proved. Finally, several numerical examples are given to illustrate the effectiveness and feasibility of the numerical scheme. [ABSTRACT FROM AUTHOR]

• A method of uncertainty analysis based on the MP-II model was proposed to examine a case of adhesive assembly. • Uncertainty transfer was constructed by a combination of finite-element simulation and a B-spline surrogate model. • The effect of the uncertainties of three types of bonding defects on the center-of-mass drift was understood. • The reliability index was improved and the parameter intervals of the bonding defects were optimized. Multi-source and strong uncertainties of the adhesive assembly process for high-precision inertial devices are critical issues that result in the current low assembly accuracy and poor assembly consistency. This paper addresses the resulting uncertainty in the center-of-mass drift of the float components of a high-precision inertial device. An interval-based non-probabilistic convex model is used to characterize the uncertainty of the bonding defect parameters of the adhesive assembly process, and the uncertainty transferring from those parameters to the center-of-mass drift is constructed by using a surrogate model and numerical simulations. A reliability analysis is carried out to understand the effect of the uncertainties of three types of bonding defects on the center-of-mass drift, and the sensitivities of the center-of-mass drift to the bonding defects are also found. The results show that the reliability index of the center-of-mass drift obtained under the initial parameter intervals is 0.689, indicating the center-of-mass drift at the risk of being out of the accuracy requirement. By adjusting the parameter intervals of the bonding defects to stabilize the center-of-mass of the assembled components, the reliability index is then improved to greater than 1. [ABSTRACT FROM AUTHOR]

Plasma gasification technology is a harmless and resourceful solid waste treatment method. As a hazardous waste, studying the plasma gasification treatment of oil-based drilling cuttings has practical significance. Therefore, this paper uses Aspen Plus to establish a plasma gasification model. Based on model validation, the effects of input power, oxygen equivalence ratio, and carrier gas type on the plasma gasification process of oil-based drilling cuttings were discussed. In addition, by designing a quadratic regression orthogonal experiment, a nonlinear quadratic regression equation was established between the three factors of gasification pressure, input power, and equivalence ratio, as well as different gasification indicators, namely gas yield, lower heating value, and gasification efficiency. By solving the equation, it was found that when the gasification power is 70 kW, the gasification pressure is 10 atm, and the equivalence ratio is 0.1, the gas yield reaches its maximum of 0.74 kg/m3; When the gasification power is 15 kW, the gasification pressure is 10 atm, and the equivalence ratio is 0.1, the lower heating value of gas production reaches its maximum of 9.68 MJ/m3; When the gasification power is 15 kW, the gasification pressure is 1 atm, and the equivalence ratio is 0.1, the gasification efficiency reaches its maximum of 37.6%. At the same time, it was found that the influence of gasification pressure, input power, and equivalence ratio on gasification indicators was ranked in descending order as equivalence ratio, input power, and gasification pressure. The above research provides certain reference values for the practical operation of plasma gasification of oil-based drilling cuttings. • Analyzed the effects of different factors on plasma gasification of OBDC. • Optimum parameters of plasma gasification of OBDC are studied. • Ranked the degree of influence of different factors on plasma gasification of OBDC. • Analyzed the efficiency of plasma gasification of OBDC. [ABSTRACT FROM AUTHOR]