Search

Variability in Eucalyptus wood density and chemical properties is crucial to understanding important factors for the forest-based industry, such as sampling methods and wood suitability as raw material. This study aimed to evaluate the basic density and chemical composition of the radial positions of young wood from the Eucalyptus urophylla clone grown under different precipitation levels. Trees from E. urophylla clonal plantations were collected in Inhambupe, Jandaíra and Itanagra, Bahia State, Brazil. Trees’ basic density and chemical composition (total extractive, lignin, hemicelluloses and α-cellulose) were determined based on the basal log of each tree, at four radial positions (1, 2, 3 and 4). It was found that the basic density and α-cellulose of wood are influenced by the cambial age and the site rainfall. There was greater increase in sections close to the bark (positions 1 and 4) and in more humid environments (sites Itanagra and Jandaríra). This finding highlights the association between wood basic density and chemical composition, mainly in the holocellulose content. [ABSTRACT FROM AUTHOR]

The aim of this study was to reveal the strength mechanism of the mortise-and-tenon (M–T) joint at a deeper level. The effects of tenon fit on bending and withdrawal load resistances, and strain distributions outside and inside beech (Fagus sylvatica) wooden round-end M–T joints were experimentally investigated using mechanical testing synchronizing digital image correlation method (DICM). The results showed that (1) the tenon fit had greater significance on withdrawal properties than that of bending properties of M–T joints; (2) the bending load resistance was linearly proportional to withdrawal load resistance based on both theoretic analysis and regression methods; (3) strain distributions outside M–T joints during the loading process were not sufficient to evaluate the mechanical behaviors of the M–T joint; (4) strain distributions inside M–T joints showed that the maximum strains on top and bottom parts of the tenon were significantly greater than that of middle part, but the difference decreased with the growth of tenon fit; (5) the method of determining the optimal tenon fit of the M–T joint based on the DICM was proposed, and optimal tenon fit of beech wooden round-end M–T joint evaluated ranged from 0.4 to 0.5 mm. [ABSTRACT FROM AUTHOR]

This paper presents a comparative analysis of the blind test outcomes of two independent methods for the identification of tropical wood species in pulp and paper products. Both, the established anatomical and the relatively new chemotaxonomic method support the European Deforestation Regulation 2023/1115 (EUDR), which aims to ensure that only legally harvested timber that has not contributed to deforestation is traded in the EU. The blind test involved 570 decisions on 15 test sheets of 37 self-manufactured mixed tropical hardwood pulps and an industrial beech pulp, used as a matrix. Both detection techniques demonstrated robust performance with over 80 % hit rates. The results show that the synergies and combination of the strengths of both methods can be utilized and lead to even better combined performance. In order to establish the chemotaxonomic identification method as a complement to the conventional anatomy-based method, statistical analyses were performed to assess its intermediate precision between three different GC-MS systems. In most cases, the method gave consistent results independent of the instrument used. [ABSTRACT FROM AUTHOR]

The anatomical description of wood and charcoal for a wide variety of purposes is an essential tool for compiling databases to correctly identify species. This study describes and compares the anatomy of the wood and charcoal of Manilkara sp., collected in a protected area in the Pará state, Brazil. The qualitative anatomical characteristics of the wood, such as diffuse-porosity; vessels in radial multiples; alternate intervessel pits; axial parenchyma in lines or reticulate; rays uniseriate or biseriate, not storied, are corroborated in the literature. Moreover, this work reports the presence of helical thickenings in the vessel elements and possible helical thickenings in fibres in Manilkara. After the carbonization process, there were morphometric changes in the anatomical elements, as an increase in vessel frequency between 23 % and 141 %, and in ray frequency between 2.8 % and 12.9 %; while ray height decreased and ray width increased. Overall, some anatomical variations could be related to, or a result of the interaction between species plasticity, genetics, age and environmental factors. These characteristics enabled the identification of the samples at the genus level and the anatomical description of the wood and charcoal can be useful for forest inspections. [ABSTRACT FROM AUTHOR]

The control authorities of timber trade lack quick and easy methods to verify the legality of the traded product. This includes the clear identification of the timber species. In this study, a simple genetic method, the macroarray technique, was modified and optimised for this purpose. The internal transcribed spacer (ITS) was used as barcode region. Specific probes were designed and tested using this barcode of trade-relevant, CITES protected wood species and their look-alikes. The results reveal that 61 of these probes are suitable for identification purposes. Hence, 32 of the 50 investigated species can be clearly identified using the developed macroarray. Additional 15 species are represented by probes in groups of two to three species, which enables a delimitation of the species present. For four species, no identification was possible applying the probes created. The findings indicate the potential of time and cost savings compared to currently established methods in species control in the timber trade. [ABSTRACT FROM AUTHOR]

Phoebe and Machilus trees, whose wood is known as Nanmu in China, face endangerment owing to long-term manmade destruction and climate change. Therefore, effective and accurate forensic tools to identify Nanmu species are required. This study developed a method for DNA identification of woods from six commonly traded Phoebe and Machilus species. DNA was efficiently extracted from oil cell-rich wood tissues, DNA barcodes were screened, species were compared, and a Nanmu DNA database was constructed. Comparison and analysis involved 26 sets of plastid genomes of Phoebe and Machilus. The five highest variable regions (Pi>0.009; psbA-trnH, psbJ, psbJ-petA, rpl32-trnL, and ycf1) were identified, and three nuclear regions (ITS, LEAFY, and RPB2) were compared. Among single DNA fragments, the nuclear DNA region LEAFY proved optimal for identifying Nanmu species, while psbA-trnH+psbJ+ycf1 was the optimal plastid combination locus. Compared with distance-based (TaxonDNA) and machine-learning analyses, the tree-based method had a lower success rate for species identification. Four labelled Nanmu samples were selected to validate the method and clustered with P. zhennan and P. sheareri data based on the LEAFY region and plastid combination locus. These findings will contribute to the conservation, classification, architecture maintenance, and trade monitoring of Nanmu natural resources. [ABSTRACT FROM AUTHOR]

A three-year pot experiment was designed to investigate cadmium (Cd) accumulation in the various parts of poplar (Populus deltoides Bartr. cv. ‘Lux’ I-69/55) by setting up 5 Cd application treatments (0, 5, 20, 50, and 100 mg/kg dry soil). The results showed that poplar exhibited a high tolerance to Cd stress, with Cd uptake significantly increasing across all plant parts as soil Cd levels rose. In general, leaves exhibited the highest Cd concentration while stems had the lowest. An upward increase trend of the accumulation of Cd in the aboveground parts from the base wood, along the stem to the branch, until the leaves, as well as a radially outward increase of Cd from the wood near the pith, to the wood near the bark, and finally to the bark, were observed. Over the three successive years, poplar trees exhibited a generally increasing extraction ability in terms of Cd concentration and the bioconcentration factor (BCF) in their aboveground parts, attributed to the enhanced leaf transpiration and conducting tissue development. The BCFs of various parts of poplar ranged from 0.09 to 6.30, following the trend of leaf > bark > branch > root > stem. [ABSTRACT FROM AUTHOR]

Beech wood, renowned for its diverse applications spanning construction, flooring, furniture, veneer, and plywood, holds a paramount position among industrial wood species. Nevertheless, the myriad of beech species worldwide, coupled with the dynamic impact of climate change, have produced structural variations within beech trees. Extensive research has scrutinized the physical and mechanical attributes of beech wood species across the globe. Findings reveal distinguishable mechanical strength, yet increased density leads to notable rates of shrinkage and swelling, somewhat constraining its utility in select domains. Identifying research gaps can create new efforts aimed at exploiting the potential of these wood resources. This paper outperforms a mere exploration of beech wood properties over the past two decades; it delves into the ramifications of climatic fluctuations, temperature shifts, wind dynamics, and soil composition. Given the lack of a comprehensive compendium documenting the full range of physical, mechanical, and microscopic attributes of the Fagus genus, this paper aims to compile information that integrates this multifaceted information. [ABSTRACT FROM AUTHOR]

This study aimed to investigate the elastic deformation of rotational wood-dowel welding joints by using the variational method, as there was no efficient tool to access the deformation behavior of welding joints perpendicular to axis orientation so far. Based on the variational method, the displacement control equation of axially-loaded dowel-welded wood joints was derived. By incorporating the boundary conditions and using an iterative approach, the parameters required in the control equation were determined. The analytical expression ϕ(r) for the deformation function of the wood substrate under elastic conditions was proposed, thereby determining the displacement and axial force of the single wood-dowel. The elasticity modulus was the primary influence parameter on the function ϕ(r). However, the welding depth had a more critical impact, and reasonable combination of parameters could lead to a better interaction between the wood dowel and substrate. The comparison between calculated results and test trials collected from the previous studies indicated that the elastic solution method could accurately estimate the pull-out ultimate bearing capacity and deformation characteristics of the welding joints. This work can provide unique perspective to understand the technology of rotational wood-dowel welding joints, and a good reference suggestion for the manufacture of multi-dowel welding joints. [ABSTRACT FROM AUTHOR]

Using pyrolysis–gas chromatography–mass spectrometry, the lignin composition was analysed in normal and reaction wood samples grown at three stem inclination angles in Gardenia jasminoides, which forms compression wood-like reaction wood. Lignin content among the samples was not significantly different. However, the reaction wood samples with larger stem inclination angles showed a lower syringyl/guaiacyl ratio. In conclusion, the degree of inclination affected the lignin composition in G. jasminoides reaction wood, and qualitative changes in lignin might be necessary to mechanically support the stems in this species. [ABSTRACT FROM AUTHOR]

The magnitudes of the color changes in heat-treated wood are closely related to the chemical composition of the wood, and changes in the chemical composition are the essential reasons for changes in the mechanical properties of heat-treated wood. The response relationships among the color parameters of heat-treated wood and the chemical composition were constructed to provide a scientific basis for regulating the mechanical properties with the color. The effects and linear correlations of the lightness indicators (L*) for poplar (Populus tomentosa Carr.) and spruce (Picea asperata Mast.) after heat treatment were related to the chemical compositions of the heat-treated woods by constructing relationships between the L* values. The relative content of cellulose in the heat-treated poplar downward trend and was significantly positively correlated with the L* value; however, the correlation with the L* value for the heat-treated spruce was insignificant. The L* value of the heat-treated wood was significantly positively correlated with the relative contents of hemicellulose, and was significantly negatively correlated with lignin. The L* value of the heat-treated wood had a superior response relationship with the crystallite sizes. Therefore, the constructed response relationship provides a theoretical basis for accurate and nondestructive testing of the mechanical properties of heat-treated wood by using the color parameters as rapid detection indicators. [ABSTRACT FROM AUTHOR]

Terahertz waves hold significant potential for applications in wood identification, owing to their good penetration and distinctive fingerprints in wood. This study focuses on wood samples from five different Guibourtia species as the research objects. The terahertz time-domain spectroscopy (THz-TDS) is employed to acquire the spectroscopic signals of the wood samples and to extract their optical parameter data. The THz refractive indices are dimensionally reduced through principal component analysis (PCA), and three machine learning models, namely partial least squares-discriminant analysis (PLS-DA), random forest (RF), and support vector machine (SVM), are employed to classify the wood of five different Guibourtia species. Time delays of the wood samples from five different Guibourtia species are concentrated in the range of 60–62 ps and exhibit different amplitudes in the frequency domain. Refractive indices showed significant variations within the THz band. PCA for dimensionality reduction of terahertz time-domain spectral data significantly improves the recognition rate of machine learning models. Applying PCA to the refractive index data, the RF model achieves a highest recognition rate of 96.9 % and an overall classification accuracy of 98 %. Current results demonstrate that THz-TDS enables rapid, accurate, and non-destructive classification and identification of wood from the Guibourtia species. [ABSTRACT FROM AUTHOR]

The porosity of cell walls, as indicated by diffusion of rhodamine B dye, in the wood of Douglas fir, radiata pine, New Zealand red beech and Shining gum was compared under dynamic conditions using fluorescence recovery after photobleaching. The comparative diffusion rate was estimated using the half-life of fluorescence recovery under water-saturated conditions performed on transverse sections. All four wood species showed similar diffusion behaviour in tracheid or fibre cell walls with slower diffusion in the middle lamella layer compared to the secondary cell wall. Within the S2 layer of the secondary wall two regions were observed, an outer region with a slow diffusion rate and an inner region with a higher diffusion rate. Vessel cell walls showed slightly slower diffusion rates. Diffusion of rhodamine B dye appears to occur primarily along the fibre axis and is probably somewhat different to water in its behaviour. This suggests that pores are aligned with cellulose microfibrils. The dye diffusion rate was estimated to be in the range of 50–100 nm2 s−1. This has implications for understanding wood drying behaviour and chemical modification of wood by infiltration with small molecules as well as water storage in living trees. [ABSTRACT FROM AUTHOR]

Pretreatment serves as an important step in maximizing the efficient utilization of woody biomass feedstock. This study focused on enhancing the component and structural properties of apple wood to optimize the utilization of apple wood resources effectively. This study presents the optimization of, the apple wood pretreatment system, combining bioenzyme and hydrothermal treatments. This study aimed to investigate the effect of different bioenzyme pretreatment conditions on the components and structural properties of apple wood extract and to analyze the feasibility of enzyme solution reuse. Fourier transform infrared spectroscopy analysis revealed an increase in cellulose content in the wood flour following enzyme treatment. Concurrently, changes in characteristic peaks indicated an increased hemicellulose content and a reduction in lignin content after the pretreatment, correlating with fraction analysis results. Scanning electron microscopy illustrated that the dense structure of the fiber surface was disrupted after treatment. Notably, the results indicated that the recovered biocomposite enzymes exhibited excellent activity, suggesting their potential for reuse. [ABSTRACT FROM AUTHOR]

Humins are heterogeneous and polydisperse furanic macromolecules derived from sugar biorefinery. Improving wood properties by humination has become of interest recently. This study examined the photodegradation stability of European pine sapwood microveneers modified with humins at different concentrations of citric acid (CA) and succinic acid (SA) as reaction catalysts, e.g., 1.5 %, 3 %, and 4.5 % wt.%. The photostability of huminated wood was assessed after 48 h, 96 h, and 144 h of exposure to the accelerated weathering test by means of mass loss and finite-span tensile strength. The results were compared with unmodified and also unweathered samples. The FT-IR spectroscopy showed apparent changes in the chemical structure of wood by humination modifications. The weight percentage gains of the samples increased with increasing the concentration of the catalyst. While no differences were observed between the samples after two weeks of the water leaching. The strength losses of weathered microveneers were, however, mostly reduced by humin-based formulas containing catalysts, where the microveneers modified with 1.5 % and 3 % CA showed respectively 32 % and 41 % lower strength loss values than the unmodified samples after 144 h of weathering. Overall, the results showed a high potential for humins to protect wood against photodegradation. [ABSTRACT FROM AUTHOR]

This study investigated the inhibition effect of nanoscale silver–copper particle (20 nm) against Coriolus versicolor and Gloeophyllumtrabeum. Poplar wood samples (Populus L.) were vacuum-impregnated using aqueous nano-AgCu solutions at concentrations of 0.01 %, 0.02 %, 0.03 %, 0.05 %, 0.075 %, and 0.1 %. Alkaline copper quaternary (ACQ, 0.1 %), boric acid (0.2 %) and untreated control group (CK) were employed for comparisons. Decay resistance and leachability were studied. The anti-fungi effects were compared between nano-AgCu, nano-Ag, Ag+ (silver nitrate), Cu2+ (copper nitrate), and a composite of Ag+–Cu2+. Nano-AgCu particle exhibited effective resistance to fungi after 12 weeks of exposure. The threshold retention of the nano-AgCu against C. versicolor and G. trabeum on poplar wood was 0.19 kg m−3 and 0.62 kg m−3, respectively. The silver–copper nanoparticles demonstrated excellent leach resistance, and the inhibition effect was retained after leaching. The nano-AgCu particle provided better antifungal effects than single ions or metal nanoparticles. This study illustrates the potential of using nano-AgCu particle as an efficient wood preservative compared to commercial water-soluble preservatives. [ABSTRACT FROM AUTHOR]

Wood is a natural composite widely employed as a residential building interior finishing. Although wood is readily available and offers benefits to the occupants, such as enhanced well-being, it is rarely employed in commercial construction due, amongst others, to the potential hazard of fire propagation. The application of flame retardant (FR) treatments leads to a reduction of wood flammability and supports wood as interior finishing. Polyelectrolyte complexes (PECs) deposition is an innovative surface treatment that has already proven its efficiency for fabrics. For wood, recent studies have highlighted that the weight gain impacted the fire-retardancy, and a minimum of 2 wt.-% was set to obtain fire protection. This study explored the potential of surface delignification to activate the wood surface and facilitate the PEC impregnation. Yellow birch (Betula alleghaniensis, Britt.) was surface delignified (0.3 mm) using sodium chlorite. The treatment impact on wood was evaluated by spectroscopy analysis (FTIR, Raman), and the increase in wood wettability was demonstrated (contact angle decreases from 50° to 35° after the surface delignification). Then, PECs consisting of polyethyleneimine and sodium phytate were surface impregnated in wood and delignified wood. The flame retardancy was evaluated using a cone calorimeter. Despite the increase in weight gain (1.5 wt.-% ± 0.3 wt.-% to 4.3 wt.-% ± 2.5 wt.-%), fire performance was not improved. This study demonstrates that lignin strongly affects char formation, even in the presence of PECs. [ABSTRACT FROM AUTHOR]

Chemical modification is an efficient strategy for improving wood quality; however, for some fast-grown wood species unwanted shrinkage occur upon treatment with alkaline solution. This study was devised to reveal the shrinkage behavior of poplar and radiata pine woods treated with 5, 10, 15 and 20 % alkaline sodium silicate (SS) solutions. Wood treated with sodium hydroxide (SH) solution adjusting to the same pH as the specific SS solution was used as a reference sample. The weight loss, chemical components analysis, and confocal microscopy revealed that treatments with SS caused considerable reductions in hemicellulose and acid-insoluble lignin (AIL) of poplar wood up to 51 % and 21 %, respectively. In contrast, such reductions of the SS-treated radiata pine wood were only 13 % and 2 %, respectively. Consequently, shrinkage of poplar wood in the tangential- and radial-directions reached up to 22 % and 11 % respectively. However, such shrinkage for radiata pine was less than 2 % in either direction. The crystallinity index of poplar and radiata pine woods after treatment increased up to 35.3 % and 4.8 %, respectively, attributable to removal of the amorphous fraction. The scanning electron microscopy displayed that treatments had minor effect on the cell structure of radiata pine, but brought about significant collapse of poplar cells. The above results show that radiata pine is more chemically stable to alkaline treatment than poplar. [ABSTRACT FROM AUTHOR]

The glass transition temperatures (Tg) of native, residual, and technical lignins are important to lignocellulose pulping, pulp processing and side stream utilization; however, how the structural changes from native to residual and technical lignin influences Tg has proven difficult to elucidate. Since the Tg of macromolecules is greatly influenced by the molecular weight, low-molecular-weight fractions, such as milled wood lignin (MWL), are poor representatives of lignin in the cell wall. To circumvent this problem, lignins of both high yield and purity were isolated from Norway spruce and softwood kraft pulp using the enzymatic mild acidolysis lignin (EMAL) protocol. Technical softwood kraft lignin was also fractionated into groups of different molecular weights, to acquire lignin that spanned over a wide molecular-weight range. A powder sample holder for dynamic mechanical analysis (DMA), was used to determine the Tg of lignins, for which calorimetric methods were not sensitive enough. The Tgs of EMAL were found to be closer to their in situ counterparts than MWL. [ABSTRACT FROM AUTHOR]

Phenol-formaldehyde (PF) resins can be impregnated and cured in situ to improve the woods dimensional stability and decay resistance. In search of renewable alternatives, the substitution of phenol by lignin cleavage products (LCP) has been discussed. However, the different chemical nature may affect the performance of the resin against fungal decay, formaldehyde emission, and equilibrium moisture content. In this study, 30 % (w/w) of the phenol in PF resins were substituted by LCP obtained from microwave-assisted pyrolysis. Scots pine sapwood was modified with the resin. The decay resistance against Rhodonia placenta, Gloeophyllum trabeum, and Trametes versicolor was determined. Additionally, effects of specimen organisation within the Petri dish, different substrates, length of leaching, and type of inoculum were studied. Further, the materials water vapor sorption properties and formaldehyde emission were determined. All modifications effectively reduced fungal decay. With 10 % weight percent gain (WPG), initial decay was detected, while 20 % WPG and 30 % WPG provided efficient protection. The substitution of phenol increases the formaldehyde emission. While further reduction in formaldehyde in the resin admixture or formaldehyde scavengers may be required, the method described herein can be used to partly replace fossil-based phenol, while maintaining good fungal resistance. [ABSTRACT FROM AUTHOR]

Carbon fraction (CF) of trees is essential for quantifying forest carbon (C) stocks. Considerable attention has been paid to CF variations at various levels with the exception of inter- and intra-growth rings. Herein, the inter- and intra-growth ring variation of CF in Pinus tabuliformis was investigated. Elemental analysis was performed to obtain CF values of the earlywood and latewood in each growth ring of the xylem. Patterns of CF variation at the growth ring level were evaluated using mixed-effect models. The results showed that latewood CF, 50.6 %, was significantly higher than earlywood CF, 49.9 % (p < 0.01). In particular, inter-growth ring variations of CF differed between heartwood and sapwood, as well as between juvenile wood and mature wood. CF values decreased nonlinearly with cambium age toward the heartwood or juvenile wood, with estimated least-squares means of 50.4 % and 51.8 %, respectively. While CF values were almost unaltered in sapwood, and slightly decreased in mature wood, with estimated least-squares means of 50.0 % and 50.2 %, respectively. It indicates that patterns of CF variation between juvenile wood and mature wood are important to estimate the C stock of P. tabuliformis. This research provides insights into C uptake dynamics to support forest management and wood utilization. [ABSTRACT FROM AUTHOR]

In this study, the influence of "bear claw" or indented growth ring anatomical patterns on the vibro-mechanical behavior of spruce wood have been investigated, particularly in the context of utilizing these singularities/specific features for the construction of violins. By employing vibrometry and modal analysis followed by finite element model updating, the vibro-mechanical properties (specific stiffness in longitudinal (L) and radial (R) directions and shear LR plane, and associated damping) of the indented growth rings spruce were identified and implemented in a numerical model of a violin. Results have revealed a significant increase in specific moduli in R direction and LR plane and decrease in L direction of spruce wood in the presence of indented growth rings, therefore accompanied by a reduction in anisotropic elastic properties, in comparison to spruce without these patterns. These properties led to changes in violin dynamics, globally increasing resonance frequencies and changing the shape of the vibration modes. The simulated frequency response function of the violin at the bridge suggested a global shift of the admittance of the bridge toward higher frequencies. These results suggest a potential impact of indented growth rings of spruce on the acoustic properties of instruments. [ABSTRACT FROM AUTHOR]

Resin production in wood tissues is a regular feature of pine wood species, including southern pine. High resin contents of southern pine wood may increase wood resistance against decay fungi. The current study investigated the effect of resin contents in southern pine wood on decay resistance by exposing non-extracted heartwood, mixed wood (sapwood + heartwood), and sapwood blocks with varying resin content to brown rot, Fomitopsis ostreiformis in a laboratory decay test. Matching blocks of each wood type were successively extracted in a Soxhlet using three solvents to determine resin content and were exposed to decay fungus in parallel. Results showed that mass losses in non-extracted heartwood and mixed wood depended on resin content levels, and very shallow or no mass losses were observed in blocks containing more than 31 % resin content. Sapwood experienced high mass losses, but the presence of resinous extractives significantly increased the decay resistance. All solvent-extracted blocks experienced high mass loss (53–55 %). Scanning electron microscopy showed that penetration of brown rot hyphae and cell damage depended on the resin contents of blocks. Most of the identified compounds through GC-MS belonged to oleoresins, among which monoterpene hydrocarbons, oxygenated monoterpenoids, and sesquiterpenes were more abundant in heartwood than sapwood. [ABSTRACT FROM AUTHOR]

The hygroscopic and moisture-dependent mechanical characteristics of small-leaved lime wood (Tilia cordata) were investigated experimentally. This study includes sorption, swelling and shrinkage experiments, as well as tension and compression tests in the three principal anatomical directions at four relative humidity levels. Four sample groups from trees of three different locations in Germany were used. The findings are comparable to those of earlier studies. The hygro-expansion anisotropy is relatively small. Young's moduli at tension/compression decreased by about 52 %/64 % in radial, 19 %/48 % in tangential and 16 %/58 % in longitudinal direction for an increase of moisture content from 10 % (65 % RH) to 20 % (95 % RH). Tension strengths/compression yield stresses decreased by about 25 %/45 % in radial, 9 %/42 % in tangential, and 32 % (compression) in longitudinal direction, respectively. These parameters increased with an increasing density. Based on the mechanical tests, Young's modulus, tension strength and compression yield stress were derived as density- and moisture-dependent material model parameters. Shear modulus and shear strength were estimated by a theoretical approach. The experimental and modelling study was accompanied by a literature survey on characteristics of lime wood relevant for hygro-mechanical material modelling. [ABSTRACT FROM AUTHOR]

The time domain nuclear magnetic resonance (TD-NMR) technique was employed to distinguish various water states, and the moisture migration during Elm wood (Ulmus rubra) heartwood vacuum drying was quantitatively analyzed. The transverse relaxation time (T2) was employed to establish the correlation between drying time and moisture migration. Additionally, the longitudinal relaxation time (T1) was utilized to identify two types of water states within the cell wall: OH bound water (B-water) and more freely bound water (C-water). Meanwhile, the changes in these two types of bound water during the drying were investigated. The results demonstrated an exponential decrease in the content of OH bound water and more freely bound water with drying time. OH bound water within the cell wall predominated, with only a small portion of more freely bound water experiencing migration loss when the moisture content (MC) dropped below 20 %. Furthermore, OH bound water exhibited higher migration rate compared to more freely bound water at 10–20 % MC, while the motion of OH bound water molecules became highly restricted and stronger binding to cell walls than more freely bound water at a MC level of below 10 %. These findings yield a theoretical foundation and empirical support for optimizing drying methods. [ABSTRACT FROM AUTHOR]

Wood wettability, the process of liquid interaction with wood surfaces, is influenced by wood surface chemistry, structure, ambient conditions, and temperature. Understanding how temperature impacts wood wettability is crucial for high-temperature manufacturing processes. In this study, the sessile drop method was employed to explore the dynamic wettability of Chinese fir wood using three different liquids (water, glycerol and polyvinyl acetate (PVAc)) across a range of temperatures (25, 40, 60 and 80 °C). By considering spreading, penetration and evaporation, we revealed that the dynamic wettability of Chinese fir was strongly dependent on temperature and the type of liquid. Temperature elevation enhances wettability, leading to reduced contact angles and increased penetration ratios. Water exhibited the highest wettability, followed by glycerol, with PVAc being the least wetting agent. Notably, after 180 s of wetting at 80 °C, the measured contact angles were 0° for water, 45° for glycerol, and 120° for PVAc. When accounting for evaporation, the penetration of water decreased from 57 % to 47 % (25 °C) and 100 % to 62 % (80 °C). The activation energies for the penetration of water and PVAc into Chinese fir exhibited variations, with values of 35.3 and 158.3 kJ/mol, respectively. These comprehensive wetting results, covering spreading, penetration and evaporation, provide valuable insights into wood–water and wood–adhesive interactions, particularly when exposed to high-temperature conditions. [ABSTRACT FROM AUTHOR]

Thermal treatment is an effective method for improving the dimensional stability of wood; however, it typically requires high temperatures. To achieve low-temperature heat treatment, this study employed wood samples impregnated with 10 % tannin acid (TA) and examined their changes in dimensional stability and chemical components after heat treatment at various initial moisture content levels. The results revealed that the TA-10 %-HT group exhibited enhanced dimensional stability. Specifically, both the tangential and radial moisture swelling decreased by 21.7 % and 11.8 %, respectively. FTIR and XRD analysis indicated that the presence of tannin acid catalytically facilitated the degradation of hemicellulose. Moreover, an increase in moisture content resulted in the ionization of TA, amplifying acidity and further affecting cellulose degradation. TGA demonstrated that TA impacted the thermal stability of heat-treated materials by lowering the initial decomposition temperature of wood components and increasing the residual weight of wood. Overall, pretreatment with TA impregnation and moisture content significantly improved the dimensional stability of Chinese fir wood and altered its chemical composition. This approach holds considerable potential for enhancing wood properties through a low-energy consumption method during the heat treatment process, expanding the practical application of wood. [ABSTRACT FROM AUTHOR]

Lignin is an abundant polymer found in wood and grasses, but due to its heterogeneity and complex macromolecular structure it has been less utilized than cellulose. While the building blocks are known, the way they are linked is less understood. Here, Molecular Dynamics simulations were used to systematically characterize seven linkages found in native lignin. Their influence on lignin and water structure, and their interactions were analyzed. The study is limited to guaiacyl (G-G) dimers connected by the following common softwood linkages; 5-5′, 4-O-5′, α-O-4′, β-1′, β-5′, β-O-4′ and β-β′. The simulations show that the linkage has a significant effect on conformational preference and lignin-water interaction. Especially, the behavior of the β-O-4′ shows unique properties, both in terms of conformational freedom and interaction with water. Within the β-O-4′ dimer, π–π stacking between the aromatic rings is possible. The molecule has two distinct common conformations, one compressed and one extended. These preferences also lead to a different effect of β-O-4′ dimer on the surrounding water, where water is found close to the linkage itself but expelled from the aromatic rings to a larger extent than the other linkages. These findings are important for lignin solubility as well as its depolymerization mechanisms. [ABSTRACT FROM AUTHOR]

This study aims to reveal the diversity of thermal-softening temperatures and identify the factors that determine this temperature. To achieve this, the thermal-softening properties of the radial direction of wood were measured under water-saturated conditions for 15 softwood and 72 hardwood specimens. Wood samples were obtained from the xylarium of the Forestry and Forest Products Research Institute, Japan. A dynamic viscoelastic measurement was performed on samples with uniform heating and cooling history because the difference in cooling rate can alter in the mechanical properties of wood. The storage and loss elastic moduli increased linearly as wood density increased, regardless of the wood species. However, the thermal-softening temperature (defined in this study as the peak temperature of loss tangent) was unrelated to the density, anatomical features, species, latitude, and annual rainfall in the habitat. When the relationship between thermal-softening temperature and lignin structure was investigated, a negative correlation was observed between the thermal-softening temperature and the syringyl ratio (syringyl/(syringyl+guaiacyl)) of lignin aromatics. This indicates that the thermal-softening temperature is higher for wood species with denser lignin structures, supporting the prior research showed correlation between thermal-softening temperature and methoxyl group content of wood. [ABSTRACT FROM AUTHOR]

The establishment of fast-growing teak plantations in Indonesia provides opportunities for shorter harvesting periods. However, it also poses challenges on wood utilization due to juvenility and growth stress-related defects. This study investigated growth stress levels and some wood properties of 10-year-old fast-growing teak grown in Gunungkidul Regency, Yogyakarta. The strain gauge method was used to measure longitudinal surface released-strains (LRS), tangential surface released-strains (TRS), and longitudinal internal residual strains (IRS). Wood specimens were also collected near each strain measurement point for the analysis of wood properties. The results showed LRS values ranging from −1243 to 320 με, TRS values ranging from −779 to 382 με, and IRS values ranging from −589 to 786 με. Meanwhile, radial variations in fiber length, modulus of elasticity, and lignin content were observed. Significant correlations were found between IRS values and microfibril angle, fiber length, modulus of elasticity, lignin content, and hemicellulose content, while no significant correlations were observed between LRS and TRS values and wood properties. These findings suggest a moderate level of growth stress. Additionally, the results also indicate that this 10-year-old fast-growing teak is still in the juvenile stage. Therefore, its utilization should be performed with caution. [ABSTRACT FROM AUTHOR]

This research focuses on increasing wood resistance against UV degradation using trimethoxyphenylsilane as modifying agent and supercritical CO2 as a green solvent and reaction medium. Trimethoxyphenylsilane was successfully grafted on European spruce (Picea abies, H. Karst) and was characterized by SEM-EDX and UV–vis reflectance. SEM-EDX showed the presence of silicium inside the wood cell wall. Increased wood moisture content showed positive effect on weight gain of trimethoxyphenylsilane after treatment. UV resistance of treated wood was evaluated by following the color change during artificial weathering. Modified samples showed improved weathering resistance compared to unmodified wood with a ΔE value around 5 after 260 h. Processing and modifying wood using supercritical CO2 is a promising route to increase wood performances and increase its use as a building material. [ABSTRACT FROM AUTHOR]

The dimensional stabilisation of wood using thermosetting resins relies on the resin uptake into the cell walls. This study tested if a conditioning step after the impregnation and before the final heat-curing enhances the cell wall uptake to improve dimensional stabilisation without increasing the chemical consumption. Small blocks of Scots pine sapwood were vacuum-impregnated with an aqueous melamine formaldehyde solution and conditioned at 33, 70, or 95 % RH for up to 1 week before drying and curing the blocks at 103 °C. However, the conditioning step decreased the cell wall bulking and the moisture exclusion effect compared to the immediate heat curing of the impregnated samples. Analyses of the resin-treated samples by scanning electron microscopy, IR spectroscopy and confocal Raman microspectroscopy provided evidence of wood hydrolysis and polycondensation of the resin within the cell lumen during the conditioning step. Hydrolysis and removal of wood constituents may have counterbalanced the cell wall bulking of the resin. Polycondensation of the resin in the lumen increased its molecule size, which could have hindered the cell wall diffusion of the resin. [ABSTRACT FROM AUTHOR]

South Africa is a water scarce country with minimal natural forests. Plantation forest species such as the Mexican tropical hard pine, Pinus patula Schiede & Deppe ex Schltdl. & Cham., was introduced into the country to satisfy local fibre demand. Today, the majority of pine plantations in South Africa are found in the Mpumalanga province. The province has diverse growing conditions in relation to climate and soil properties. Sample plots were established in even-aged P. patula plantations and stratified according to soil parent material and altitude. Growing conditions of each sample plot were characterised according to climate and soil properties. A total of 540 sample trees were measured for height, diameter, density, and latewood content. The sample trees were harvested to produce 2690 logs. The logs were milled, and the resultant lumber was graded according to density, dynamic modulus of elasticity, and modulus of rupture. Annual maximum temperature had the most significant impact on tree growth, while rainfall correlated with wood density and latewood content of standing trees. However, annual maximum temperature and tree height had a negative relationship with the recovered lumber properties and dimensional stability. Spring rainfall appeared to be the most important factor influencing lumber twist and this was possibly due to the associated larger juvenile core present in the trees. [ABSTRACT FROM AUTHOR]

This study evaluated the mechanical properties of the scrimber wood produced from date palm fronds and compared it to other wood-based materials. The raw materials for the production of the scrimber wood were date palm fronds. The scrimber wood was produced using a fabrication process that included the following stages: washing, cutting, burning, and gluing the pieces. The results showed that the mechanical properties of the scrimber wood produced using date palm fronds were very similar to those of other woods used for the same purpose. It was found that the wood produced was strong enough to hold several heavy objects without deforming or breaking. In addition, no defects, such as cracks or holes, were observed on the surface of the wood after processing. The results revealed that frond-scrimber trees recorded the largest deflection before fracture due to their fibrous features. The fibrous structure of the frond scrim may explain its strength and durability, as it successfully supplied samples with high fracture points, similar to hardwood, and prolonged maximum displacement, similar to certain softwoods. The dynamic characterization of the scrimber wood specimens reveals their inherent frequencies, mode forms, damping ratios, and other dynamic properties; such insights may help forecast their performance under different loads. [ABSTRACT FROM AUTHOR]

This study investigated the characteristics of radial cracks in Castanopsis hystrix wood and evaluated its dimensional stability after impregnation with low-molecular-weight polyacrylate (PA), melamine-urea-glyoxal (MUG), and melamine-urea-formaldehyde (MUF) resins. The physical properties were examined by dimensional stability measurements, dynamic vapor sorption (DVS) analysis, and scanning electron microscopy (SEM). The results showed that radial cracks were easily produced in the transverse section of untreated wood during drying. The surfaces of the radial cracks exhibited an even and clean structure without fluffs on the pair of surfaces, and cracks spanned 4–5 annual rings. The resin-impregnated wood showed no radial cracks on its transverse surface. C. hystrix wood modified with MUG and MUF exhibited a higher weight percentage gain (WPG) than wood modified with the same concentration of PA resin. The resin-impregnated C. hystrix wood also showed reduced anisotropy and improved dimensional stability. The SEM images of the modified wood showed that the wood pits and cells were filled with resin, while the cell wall surfaces were covered with a layer of resin. [ABSTRACT FROM AUTHOR]

This study involved analysing the carbon-13 isotope ratio (δ13C) of cellulose, lignin, and whole wood powder of Balanites aegyptiaca to determine the optimal substrate for future ecophysiological studies. From seven different trees (i.e., three from the Sudanian zone and four from the Chadian Sahelian zone), 21 samples were taken for this study. Identical variation trends were observed with cellulose, lignin, and whole wood powder, with δ13C values for cellulose always higher than for the other substrates, although the trees were located under different climatic conditions. The means obtained were −26.0 ‰, −28.7 ‰, and −27.1 ‰, for cellulose, lignin, and whole wood powder, respectively. Spearman's correlation test, which was used to analyse relationships between the results, revealed a strong correlation (r2 = 0.93) between the δ13C cellulose values and those of whole wood powder from B. aegyptiaca, as well as between the δ13C cellulose values and those of lignin (r2 = 0.73). This strong correlation between cellulose and wood powder results, and between cellulose and lignin, suggests that the isolation of cellulose is not necessary for δ13C analysis of B. aegyptiaca wood. [ABSTRACT FROM AUTHOR]

Accurate and rapid wood species identification is vital for wood utilization and trade. This goal is achievable with the fast development of deep learning (DL). Several studies have been published related to this topic; however, they were limited by their generalization performance in practical applications. Therefore, this study proposed a DL multimodal fusion framework to bridge this gap. The study utilized a state-of-the-art convolutional neural network (CNN) to simultaneously extract both short-wavelength near-infrared (NIR) spectra and RGB image feature, fully leveraging the advantages of both data types. Using portable devices for collecting spectra and image data enhances the feasibility of onsite rapid identification. In particular, a two-branch CNN framework was developed to extract spectra and image features. For NIR spectra feature extraction, 1 dimensional NIR (1D NIR) spectra were innovatively encoded as 2 dimensional (2D) images using the Gramian angular difference field (GADF) method. This representation enhances better data alignment with CNN operations, facilitating more robust discriminative feature extraction. Moreover, wood's spectral and image features were fused at the full connection layer for species identification. In the experimental phase conducted on 16 difficult-to-distinguish wood samples from the Lauraceae family, all achieved identification metrics results exceed 99 %. The findings illustrate that the proposed multimodal fusion framework effectively extracts and fully integrates the wood's features, thereby, improving wood species identification. [ABSTRACT FROM AUTHOR]

Microscopic lab-based X-ray computed tomography (XµCT) aided finite element (FE) modelling is a popular method with increasing nature within material science to predict local material properties of heterogeneous materials, e.g. elastic, hygroexpansion and diffusion. This method is relatively new to wood and lacks a clear methodology. Research intended to optimise the XµCT aided FE process often focuses on specific aspects within this process such as the XµCT scanning, segmentation or meshing, but not the entirety of the process. The compatibility and data transfer between aspects have not been investigated to the same extent, which creates errors that propagate and negatively impact the end results. In the current study, a methodology for the XµCT aided FE process of wood is suggested and its bottlenecks are identified based on a thorough literature review. Although the complexity of wood as a material makes it difficult to automate the XµCT aided FE process, the proposed methodology can assist in a more considered design and execution of this process. The main challenges that were identified include an automatic procedure to reconstruct the fibre orientation and to perform segmentation and meshing. A combined deep-learning segmentation method with geometry-based meshing can be suggested. [ABSTRACT FROM AUTHOR]

Understanding the durability of emerging plantation hardwood resources is important for optimising their production and use. This study compared timber density, extractives content and decay resistance in 12–13-year-old plantation and native forest regrowth Gympie messmate (Eucalyptus cloeziana) trees. Density increased from pith to bark for both plantation and native forest trees. Inner heartwood density of the plantation timber was significantly lower than that of the native forest regrowth timber. While the total extractives content of the outer heartwood was comparable in the plantation and native forest regrowth trees, the inner heartwood of the latter contained significantly greater extractives levels. Laboratory decay tests showed that all heartwood zones of plantation and native forest regrowth Gympie messmate were resistant to decay by the white rot Pycnoporus coccineus. The inner heartwood of the plantation timber was, however, susceptible to decay by the brown rot Fomitopsis ostreiformis. The results illustrate the potential variations in wood quality parameters to be considered when moving from native forest to plantation resources that are harvested at a younger age and managed for more rapid wood production. [ABSTRACT FROM AUTHOR]

The article offers a perspective on how thermal-modification affects the impact bending strength of five different wood species, an aspect that has not received as much attention as the well-studied static load behavior of thermally-modified timber (TMT). Since the TMTs are mainly employed as outdoor materials, where they may encounter impact forces, a comparative investigation into the flexibility and strength of these materials under impact is useful. This article evaluates different aspects of the TMT, such as deflection, strain in the impact region, the maximum force needed to initiate cracks, and the energy required for rupture. Wood planks from ash, beech, larch, oak, and spruce were thermally modified at 180 and 220 °C. They were cut into test specimens, while a separate set of unmodified specimens from each wood species served as the reference group. The specimens were subjected to an impact 3-point bending test, and an ultra-high-speed camera meticulously recorded the results. The images were processed by the digital image correlation (DIC) method to determine the deflection and strain distribution of the beams during the impact test. The deflection, maximum force, maximum longitudinal strain, and required work for rupture of each group were determined. The results showed that thermal-modification decreases the wood deflection and maximum longitudinal strain by approximately 50 %. In addition, the impact bending strength decreased by nearly 60 %. However, the impact bending strength did not exhibit a statistically significant decrease at 180 °C; in some cases, it even increased. [ABSTRACT FROM AUTHOR]

The European Deforestation Regulation 2023/1115 (EUDR) prohibits trading of wood and wood products obtained from illegal logging on the EU market. While the identification of solid wood via anatomy, chemistry and genetics has already been established, there is a lack of identification methods for pulp and paper that complement anatomy. This publication presents a newly developed chemotaxonomic method for identifying mixed tropical hardwood (MTH) species in pulp and paper products based on their extractives analyzed with thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS). The measured data was processed and compared to identify marker substances and was then merged into a fingerprint database for identifying MTH species in paper of unknown composition. As database references, fully bleached kraft pulps were produced from 38 anatomically identified wood samples and then cryo-ball milled and extracted successively with n-hexane and acetone. The results show that the remaining wood extractives generated from bleached pulps are specific enough to find chemical relevant marker substances to detect MTH species. As chemical composition and anatomy are independent characteristics of wood, this paper makes a completely independent method available, which potentially improves the screening for Convention on International Trade in Endangered Species of Wild Fauna and Flora (CITES) protected species. [ABSTRACT FROM AUTHOR]

Natural durability is one of the most rated features in wood end-use applications. In fact, several precious native tropical wood species produce timber of high natural durability, which is also related to long service life even for the highest hazard classes. However, selective logging is driving the existing volume of this group of species to near extinction. The remainder of the alternative species produces perishable timbers, which require synthetic chemical protection to prolong their service life but with detrimental effects on humans and the environment. Therefore, transferable durability has emerged as an alternative to gradually substitute traditional wood preservatives. From this approach, extractives from naturally durable wood species are removed and transferred to the non-durable wood species as an alternative environmental-friendly option for wood protection. Indeed, extractives from durable wood species have proven to have a deterrent effect on fungi, bacteria and termites and could be used to protect perishable wood species. Thus, this review aims to assess the prospects of developing environmentally friendly wood preservatives based on extractives sourced from highly natural, durable wood species to treat and add value to the group of perishable timbers. A step-wise analysis offers insights and challenges on (i) potential sources of extractives; (ii) effective extraction methods; (iii) extractive-based preservative formulation; and (iv) effective treatment methods for better preservative fixation for better wood protection. Accounts about the way forward for the development of extractive-based wood preservatives are also presented. [ABSTRACT FROM AUTHOR]

Flame-retardant impregnation and densification are two major modification techniques to improve the fire safety of wood. Here, these two techniques were combined to prepare flame-retarded wood, aiming at further fire hazard reduction. The delignated Pinus sylvestris L. was impregnated with boric acid (BA) and graphene oxide (GO) solutions, then densified to prepare densified flame-retarded wood named BGO-DW sample. The results revealed that the BGO-DW sample obtained a limiting oxygen index (LOI) value of 47.4 %. Its backside temperature after 1200 s heating was 49 % lower than that of unmodified wood. Besides, the peak heat release rate (PHRR) and total heat release (THR) values of BGO-DW sample were 72 and 62 % lower than those of unmodified wood due to its shorter pyrolysis interval and lower peak mass loss rate (PMLR), as supported by thermogravimetric (TG) analysis. The flame retardancy of BGO-DW sample could be attributed to the formation of compatible char containing C=C aromatic structure, C–O–C cross-linked structure, and boron trioxide (B2O3) structure. These features of BGO-DW sample offer a new method to improve thermal stability, heat insulation, and flame retardancy for wood and wood-based products. [ABSTRACT FROM AUTHOR]

Wood and bamboo are the greenest renewable materials used for construction, furniture, and decor from the ancient ages. However, wood and bamboo have intrinsic faults like durability, ductility, physical and mechanical strength, and stability, limiting their applications in the industry. On the other hand, nanotechnology is a popular technology having numerous applications in different fields, resulting in a significant increase in expectations among academics, investors, the government, and industries. In contrast, nanotechnology can protect wood and bamboo from extreme conditions (bacteria, climate, etc.) by improving physicochemical characteristics because of its unique features. Nowadays, the trend of merging nanotechnology and forest industries to overcome the limitations mentioned above and get economically sustainable materials for construction, furniture manufacturing, flexible sensors developments, energy storage, battery manufacturing, and many more is increasing. Presently, several reviews on wood and bamboo modification by nanoparticles and nanomaterials have already been published. But, at this time, this study is essential because it aims to provide a brief guide about the recently developed eco-friendly sustainable materials from wood and bamboo, their uses, and how they can affect people’s daily life and helps to point out the gap of the current knowledge. In addition, we briefly describe the conventional and modern modification methods, including the influence of nanomaterials on wood and bamboo structures. This article is outlined as follows: The first phase of the review deals with wood and bamboo modification methods. The second phase explains how the modification method improves the properties of wood and bamboo materials, and the last step will describe the recent innovation of wood and bamboo materials.

The objective of the study was to improve the stiffness and bending strength of laminated bamboo through confinement with softwood. A total of 144 beams were tested, divided into 6 groups of 24 specimens each. The tests were conducted on specimens of laminated bamboo, wood, and composite sections with different levels of confined bamboo laminate (20, 40, 60, and 80%). The results indicated that the composite exhibited optimal behavior when the ratio of bamboo to wood was between 46 and 54%. Furthermore, the composite demonstrated a bending modulus of elasticity that was 16.6% higher and a modulus of rupture that was 18.3% higher than the values predicted by the mixing rule. A mathematical model was developed to predict the design mechanical properties based on composite thickness. This model was validated through 18 additional bending tests. This new material is an environmentally sustainable alternative that has the potential to be used as beams in buildings, providing improved mechanical performance, reduced weight, and lower manufacturing cost compared to bamboo laminates.

Wood surface charring is a treatment method commonly employed to enhance weather protection and aesthetic appearance of building exteriors. This study aims to investigate the differences between two wood surface charring processes: the traditional Japanese method known as Yakisugi and an alternative charring technique industrially manufactured with a gas burner. The objective of the study was to assess whether a thicker layer after Yakisugi treatment has any advantages over a thinner layer after the alternative process. Vibrational spectroscopy techniques including UV resonance Raman (UVRR) and Fourier transform infrared (FTIR) spectroscopy, were utilized in conjunction with X-ray-micro-CT analysis. The findings revealed that ATR-FTIR spectroscopy detected the degradation of carbohydrates and changes in lignin within the charred surface, although both processes exhibited similar vibrational contributions. In contrast, UVRR spectroscopy provided insights into the carbonized layers, revealing spectral differences indicating variations in temperature during the charring processes. X-ray micro-CT analysis visually highlighted significant differences in the coal layers, suggesting distinct combustion profiles. Remarkably, the macrostructure of wood treated with Yakisugi remained intact despite a thicker charred layer compared to the alternative charring techniques. However, further investigations are required to assess the weather stability of the alternative charring method for a comprehensive understanding. [ABSTRACT FROM AUTHOR]

Thermally modified timber (TMT) reduces hygroscopicity, increases dimensional stability, and decay resistance. Although there is a substantial amount of research on heat-treated wood, investigations on the sensitivity of cell wall swelling behavior to water variation are limited. Therefore, this study focused on the swelling behavior of TMT from cellular and chemical perspectives. The effects of heat treatment on the hygroscopicity and swelling behavior of the wood cell walls were studied using dynamic vapor sorption and confocal laser scanning microscopy. Changes in the chemical composition and cellulose crystallinity were studied using attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray diffraction. The results revealed that the hygroscopic swelling of latewood significantly decreased with increasing treatment temperature, reducing the anisotropy of the wood cell swelling. The hygroscopicity of wood was reduced by heat treatment, and a clear decrease in hysteresis was observed at elevated treatment temperatures. The FTIR spectra indicated that both hemicellulose and lignin were degraded. The crystallinity and lateral size of the cellulose increased after heat treatment. Similar changes in the chemical composition and crystallinity of cellulose were observed in the latewood and earlywood. [ABSTRACT FROM AUTHOR]

Conventional fluorescence spectroscopy has been suggested as a valuable tool for classifying wood species rapidly and non-destructively. However, because it is challenging to conduct absolute emission intensity measurements, fluorescence analysis statistics are difficult to obtain. In this study, another dimension of fluorescence, that is, fluorescence lifetime, was further evaluated to address this issue. A time-resolved fluorescence spectroscopic measurement system was first designed, mainly using a streak camera, picosecond pulsed laser at 403 nm, and a spectroscope, to collect the fluorescence time-delay (FTD) profiles and steady-state fluorescence intensity (FI) spectra simultaneously from 15 wood species. For data analysis, principal component analysis was used to "compress" the mean-centered FTD and FI spectra. Then, support vector machine classification analysis was utilized to train the wood species classification model based on their principal component scores. To avoid overfitting, ten-fold cross-validation was used to train the calibration model using 70 % of the total samples, and the remaining 30 % hold-out validation was used to test its reproducibility. The cross-validation accuracies were 100 % (5 softwoods) and 96 % (10 hardwoods), with test-validation accuracies of 96 % and 89 %. [ABSTRACT FROM AUTHOR]

Planting spacing plays an important role in tree growth and wood formation. Thus, the aim of this study was to determinate how planting spacing and genetic material affect the radial variation of basic density and chemical composition of wood. The sampling of this study was based on 4 clones of Eucalyptus urophylla × Eucalyptus grandis at 5 years of age planted in four spacings (3 × 1, 3 × 2, 3 × 3 and 3 × 4 m). To determine the basic density (BD), extractive (EXT) and lignin (LT) content, wood discs were removed at breast height, which were sectioned in three radial positions (pith, intermediate and sapwood). The results showed that genetic material, planting spacing and radial position affected the values of BD, EXT and LT content. The BD and EXT content tended to increase with increased planting spacing, while the LT content tended to decrease. In relation to the radial variation, the basic density showed an increase in the pith-bark direction, while the EXT content showed a decrease in this direction. For LT, no significant difference was observed in the pith-bark direction. In general, the largest planting spacings promoted the highest rates of variation of the properties studied. [ABSTRACT FROM AUTHOR]

Plantation forest species were introduced into South Africa due to limited availability of native forests for wood-derived products. Currently, the Mexican pine species, Pinus patula, is the most widely planted softwood species in the country. To study the effect of growth environment on wood and processing properties for the species, sample plots were established in a 20-year rotation covering a wide range of soil geologies and altitudes in Mpumalanga, South Africa. Temperature and seasonal rainfall were also determined for the sample plots. Randomly selected sample trees were harvested from the plots and processed at a plywood plant to determine veneer recovery and quality. Trees grown on sites composed of granite soils, with higher annual maximum temperatures and less rainfall, found in the Highveld region, displayed superior tree size, slenderness, and volume growth, compared to trees grown on dolomite and shale soils common to the Lowveld region. Veneer derived from Lowveld trees had more splits which were largely related to defects. Larger trees also had a greater percentage volumetric heartwood and a smaller live crown, compared to smaller trees. Highveld trees had greater net veneer recovery and produced better quality veneer than trees grown on the Lowveld. In the Mpumalanga forestry region, strong co-relatedness exists between soil geology, altitude, and climate. Although tree form and wood properties were found to differ with varying soil geology and altitude, these differences were primarily related to climate rather than soil properties. These findings highlight the pitfalls associated with neglecting either climate or soil properties when analysing site-specific growing conditions on tree growth and form. [ABSTRACT FROM AUTHOR]