Search

We report on the first deployment of a ytterbium (Yb) transportable optical lattice clock (TOLC), commercially shipping the clock 3,000 km from Boulder, Colorado to Washington DC. The system, composed of a rigidly mounted optical reference cavity, atomic physics package, and an optical frequency comb, fully realizes an independent frequency standard for comparisons in the optical and microwave domains. The shipped Yb TOLC was fully operational within 2 days of arrival, enabling frequency comparisons with rubidium (Rb) fountains at the United States Naval Observatory (USNO). To the best of our knowledge, this represents the first deployment of a fully independent TOLC, including the frequency comb, coherently uniting the optical stability of the Yb TOLC to the microwave output of the Rb fountain., Comment: 5 pages, 4 figures

Coherent frequency division of high-stability optical sources permits the extraction of microwave signals with ultra-low phase noise, enabling their application to systems with stringent timing precision. To date, the highest performance systems have required tight phase stabilization of laboratory grade optical frequency combs to Fabry-Perot optical reference cavities for faithful optical-to-microwave frequency division. This requirement limits the technology to highly-controlled laboratory environments. Here, we employ a transfer oscillator technique, which employs digital and RF analog electronics to coherently suppress additive optical frequency comb noise. This relaxes the stabilization requirements and allows for the extraction of multiple independent microwave outputs from a single comb, while at the same time, permitting low-noise microwave generation from combs with higher noise profiles. Using this method we transferred the phase stability of two high-Finesse optical sources at 1157 nm and 1070 nm to two independent 10 GHz signals using a single frequency comb. We demonstrated absolute phase noise below -106 dBc/Hz at 1-Hz from carrier with corresponding 1 second fractional frequency instability below $2\times10^{-15}$. Finally, the latter phase noise levels were attainable for comb linewidths broadened up to 2 MHz, demonstrating the potential for out-of lab use with low SWaP lasers.

We report an accurate measurement of the phase noise of a thermally limited electronic oscillator at 300 K. By thermally limited we mean that the white signal-to-noise ratio of the oscillator is at or near the level generated by the thermal noise of the 50 ohm source resistor. The measurement is devoid of the anti-correlation effect that originates from the common mode power splitter in a cross-spectrum technique. The anti-correlation effect is mitigated by cooling the power splitter to a liquid helium temperature (4 K). The measurements in this paper are the first proof of theoretical claims that additive thermal noise from the splitter can be reduced significantly with cryogenic cooling and this can eliminate any anti-correlated noise introduced by use of the two-channel cross-spectrum technique. We also confirm measurements of partial anti-correlation error of (-1.3 +/- 0.6) dB that agree with theory when the splitter is at liquid nitrogen temperature of 77 K., Comment: 8 pages, 6 figures

Cross-spectrum analysis is a commonly-used technique for the detection of phase and amplitude noise of a signal in the presence of interfering noise. It extracts the desired correlated noise from two time series in the presence of uncorrelated interfering noise. Recently, we demonstrated that the phase-inversion (anti-correlation) effect due to AM noise leakage can cause complete or partial collapse of the cross-spectral function. In this paper, we discuss the newly discovered effect of anti-correlated thermal noise that originates from the common-mode power divider (splitter), an essential component in a cross-spectrum noise measurement system. We studied this effect for different power splitters and discuss its influence on the measurement of thermal-noise limited oscillators. An oscillator whose thermal noise is primarily set by the 50 ohm source resistance is referred to as a thermally-limited oscillator. We provide theory, simulation and experimental results. In addition, we expand this study to reveal how the presence of ferrite-isolators and amplifiers at the output ports of the power splitters can affect the oscillator noise measurements. Finally, we discuss a possible solution to overcome this problem.

We describe the design of a low-phase-modulated (PM) noise, 40 GHz oscillator that uses a conventional air-dielectric cavity resonator as a frequency discriminator to improve the PM noise of a commercial 10 GHz dielectric resonator oscillator (DRO) frequency multiplied by four. The main features of this design incorporate (1) unloaded cavity quality factor (Q) of 30,000, (2) high coupling coefficient, (3) large carrier suppression by use of interferometric signal processing, (4) large operating signal power of approximately 1 watt (W), and (5) relatively small size. In addition, we report the PM noise of several Ka-band components.

Cross-spectral analysis is a mathematical tool for extracting the power spectral density of a correlated signal from two time series in the presence of uncorrelated interfering signals. We demonstrate and explain a set of conditions where the detection of the desired signal using cross-spectral fails partially or entirely in the presence of a second uncorrelated signal. Not understanding when and how this effect occurs can lead to dramatic underreporting of the desired signal. Theoretical, simulated and experimental demonstrations of this effect as well as mitigating methods are presented.

We utilize and characterize high-power, high-linearity modified uni-traveling carrier (MUTC) photodiodes for low-phase-noise photonic microwave generation based on optical frequency division. When illuminated with picosecond pulses from a repetition-rate-multiplied gigahertz Ti:sapphire modelocked laser, the photodiodes can achieve 10 GHz signal power of +14 dBm. Using these diodes, a 10 GHz microwave tone is generated with less than 500 attoseconds absolute integrated timing jitter (1 Hz-10 MHz) and a phase noise floor of -177 dBc/Hz. We also characterize the electrical response, amplitude-to-phase conversion, saturation and residual noise of the MUTC photodiodes., Comment: 3 pages, 3 figures

Asserts that traditional teaching methods are unintentionally biased towards the elite and against many non-traditional students. Outlines several easily accessible changes in teaching methods that have fostered dramatic changes in student performance with no change in standards. These approaches have proven effective even in the fields of mathematics and science. (MJP)

The relationship between collaborative learning and some major theoretical and empirical approaches to fostering critical thinking are examined. Three frameworks for combining collaborative learning and critical thinking are suggested: use of mental models, creation of discourse communities, and creation of disciplinary discourse communities. (MSE)