Search

The stability and reproducibility issues related to metal halide Perovskite Solar Cells (PSCs) have prevented so far from exploiting this highly efficient photovoltaic technology under rainy or even moisture conditions and in combination with drop triboelectric nanogenerators (D-TENGs). Protecting the PSCs with a waterproof encapsulator could overcome such a disadvantage. Herein, we propose the implementation of fluorinated carbon (CFx) coatings produced by PECVD, enabling waterproof capability for the PSC and working as an energy harvesting surface for D-TENGs. These 100 nm - films present optimal optical transmittance, fully preserving the photovoltaic parameters of the cell. The improved long-term stability of the water-resistant PSCs prevents degradation under illumination in outdoor or simulated adverse environments with high humidity, high temperature, water immersion, or rain. As a remarkable result, the 50% Power Conversion Efficiency (PCE) has been retained after ten days of illumination under 100% relative humidity at 50 degrees Celsius. Also, the CFx coatings were successfully tested as a promoter agent to integrate commercial UV-curable sealants compatible with Spiro-OMeTAD, enhancing the performance stability of up to 80 % of PCE after 100 hours under illumination in a humid environment. This PSC was tested in a top-bottom electrode configuration for harvesting kinetic energy from droplets. Devices were compatible with simultaneously working as D-TENG and photovoltaic cells, yielding voltage outputs up to 12 V with maximum peak power density reaching 2.75 uW/cm2 defined by the D-TENG and PCE of 11.5 % and 8.46 mA/cm2 of short circuit current determined by the PSC under dripping and for an illumination angle of 45 degrees. The durability of the multisource device was tested under constant illumination and periodical drop impacting for more than 5 hours.

The ultimate step towards the exploitation of water as a clean and renewable energy source addresses the energies stored in the low frequencies of liquid flows, which demands flexible solutions to adapt to multiple scenarios, from raindrops to waves, including water moving in pipelines and microdevices. Thus, harvesting low-frequency flows is a young concept compared to solar and wind powers, where triboelectric nanogenerators have been revealed as the most promising relevant actors. However, despite widespread attempts by researchers, the drop energy harvesters' output power is still low, mainly because of the limitations in candidates endowed with ideal triboelectric and wetting properties and also the non-optimal and centimetre-scale device architecture that prevents the conversion of the complete kinetic energy of impinging drops. Herein, we disclose a microscale triboelectric nanogenerator that can harvest a high density of electrical power from drops through a single, submillisecond, long-lasting step. The mechanism relies on an instantaneous electrical capacitance variation owing to the high-speed contact of the drops with the electrodes' active area. We discuss the role of the precharged effect of the triboelectric surface in the time characteristic of the conversion event. The capacitive and microscale structure of the device is endowed with a small form factor that allows for the production of densely packed arrays. The proposed architecture can be adjusted to different liquids and scales and is compatible with a variety of triboelectric surfaces, including flexible, transparent, and thin-film approaches., Comment: 23 pages, 6 figures in main text, 9 figures in Supporting Information, videos available from the authors

Despite the youthfulness of hybrid halide perovskite solar cells, their efficiencies are currently comparable to commercial silicon and have surpassed quantum-dots solar cells. Yet, the scalability of these devices is a challenge due to their low reproducibility and stability under environmental conditions. However, the methods reported to date to tackle such issues recurrently involve the use of solvent methods that would further complicate their transfer to industry. Herein we present a reliable alternative relaying in the implementation of an ultrathin plasma polymer as passivation interface between the electron transport material and the hybrid perovskite layer. Such nanoengineering interface provides solar devices with increased long-term stability under ambient conditions. Thus, without consideringr any additional encapsulation step, the cells retain more than 80 % of their efficiency after being exposed to the ambient atmosphere for more than 1000 h. Moreover, this plasma polymer passivation strategy significantly improves the coverage of the mesoporous scaffold by the perovskite layer, providing the solar cells with enhanced performance as well as improved reproducibility.

It is shown that magnetic forces as the Lorentz force, exerted on electric currents, and the force {\mu}Div(B), exerted on electron spins at rest, account for both the transverse spin imbalance typical of spin Hall effect and the transverse charge imbalance associated with pure spin currents (inverse spin Hall effect). Considering that for stationary currents the laboratory reference frame and those for which the spin up and spin down carriers are at rest are inertial systems, one can easily find the forces exerted by the lattice on both spin sub-bands, as well as the force between sub-bands., Comment: 3 pages main body, 3 figures, 1 page supplementary information