Search

The results of X-ray photoemission (XPS) and valence bands spectroscopy, optically stimulated electron emission (OSEE) measurements and density functional theory based modeling of graphene oxide (GO) placed on Cu via an electrophoretic deposition (EPD) are reported. The comparison of XPS spectra of EPD prepared GO/Cu composites with those of as prepared GO, strongly reduced GO, pure and oxidized copper demonstrate the partial (until C/O ratio about two) removal of oxygen-containing functional groups from GO simultaneously with the formation of copper oxide-like layers over the metallic substrate. OSEE measurements evidence the presence of copper oxide phase in the systems simultaneously with the absence of contributions from GO with corresponding energy gap. All measurements demonstrate the similarity of the results for different thickness of GO cover of the copper surface. Theoretical modeling demonstrates favorability of migration of oxygen-containing functional groups from GO to the copper substrate only for the case of C/O ratio below two and formation of Cu-O-C bonds between substrate and GO simultaneously with the vanishing of the energy gap in GO layer. Basing on results of experimental measurements and theoretical calculations we suggest the model of atomic structure for Cu/GO interface as Cu/CuO/GO with C/O ratio in gapless GO about two. © 2018 Elsevier B.V.

Anodization of electropolished tantalum improves the bioactive properties of the surface by increasing the thickness of the oxide layer. The results allow to select optimal conditions for treatment of metal implants. Anodizing at 20 V already sufficient to generate a sample on the surface of the oxide layer Ta2O5.

This paper presents research on modifying the surface of Ti-15Mo alloy using electropolishing and anodic passivation. The electropolishing process was carried out in solutions containing sulfuric acid, ethylene glycol, ammonium fluoride and oxalic acid. Whereas a voltage range from 20 to 100 V and a 1 M orthophosphoric acid solution were used during the anodic passivation. The influence of above mentioned processes parameters on the quality of the obtained oxide layer on Ti-15Mo alloy was investigated. The analysis of Ti-15Mo surface after modification was performed using scanning electron microscopy (SEM), atomic force microscopy (AFM), energy-dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), ellipsometry, and mechanical tests. Moreover, the corrosion resistance was investigated using a potentiostatic method in Ringer's solution. It was found that electropolishing leads to an increase in the surface homogeneity and to the form of an oxide layer, which consisted of TiO2 and MoO3. Whereas the oxide layers obtained during anodic passivation were characterized by different properties depending on the applied voltage. The anodic passivation at various voltages (20-100 V) increased the surface wettability (94.5°-87.6°) in comparison to the electropolished sample (97.5°). Moreover, the obtained oxide layer after anodization exhibited a high hardness. The electrolytic polishing and anodic passivation of Ti-15Mo also improved corrosion resistance of the alloy in contact with Ringer's solution. The sample anodized at 80 V presented the highest corrosion resistance by the smallest corrosion current density (1.4 nA cm-2) and the highest polarization resistance (37.4 MΩ cm2). © 2016 Elsevier Ltd. All rights reserved.

Investigations into the surface modification of a Ti-15Mo alloy via plasma electrolytic oxidation are reported. The oxidation process was conducted in a solution containing Ca(H2PO2)2, H 3PO4, or (HCOO)2Ca. Anodisation was performed at voltages in the range of 100-400 V. The morphology of the sample surface did not change during alloy oxidation at lower voltages. Higher voltages led to the incorporation of calcium and phosphorus or of calcium only into the formed oxide layer and to significant modification of the surface morphology. Based on the SEM and EDX analysis results, a set of samples was selected for further investigations. To study the surface of the Ti-Mo alloy after anodic oxidation, we used scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), thin-layer X-ray diffraction (TL-XRD), and X-ray photoelectron spectroscopy (XPS). The electrochemical characteristics of the modified alloy in Ringer's solution were determined. Anodisation results in a considerable increase in the corrosion resistance of the Ti-15Mo alloy. © 2013 Elsevier Ltd.