Search

High room temperature n-type mobility, exceeding 300 cm2/Vs, was demonstrated in Si-doped AlN. Dislocations and CN−1 were identified as the main compensators for AlN grown on sapphire and AlN single crystalline substrates, respectively, limiting the lower doping limit and mobility. Once the dislocation density was reduced by the growth on AlN wafers, C-related compensation could be reduced by controlling the process supersaturation and Fermi level during growth. While the growth on sapphire substrates supported only high doping ([Si] > 5 × 1018 cm−3) and low mobility (∼20 cm2/Vs), growth on AlN with proper compensation management enabled controlled doping at two orders of magnitude lower dopant concentrations. This work is of crucial technological importance because it enables the growth of drift layers for AlN-based power devices. [ABSTRACT FROM AUTHOR]

Reduction in compensation in Si-doped Al-rich AlGaN is demonstrated via chemical potential control (CPC). The chemical potentials and the resulting formation energies of carbon on the nitrogen site (CN) and cation vacancy complex with Si (VIII + nSiIII) were related to growth variables through a thermodynamic supersaturation model, which quantitatively predicted the incorporation of CN and the generation of the VIII + nSiIII complex. The compensation "knee" behavior, i.e., decreasing conductivity with increasing Si incorporation beyond a certain concentration, was successfully controlled. The maximum free carrier concentration was improved by impeding the formation of VIII + nSiIII complexes under III-richer conditions, while the impurity compensation by CN was reduced by making the growth environment N-richer. The results of Hall effect measurement and photoluminescence agreed well with quantitative theoretical predictions of the CPC model. Based on the developed model, the highest conductivity of 160 Ω−1 cm−1 with free carrier concentration of 3 × 1019 cm−3 in Al0.7Ga0.3N ever reported was achieved on single crystal AlN substrates. The demonstrated predictive power of the CPC model should greatly reduce the empirical analysis or iterative experimentation that would otherwise be necessary. [ABSTRACT FROM AUTHOR]

Highly conductive Ge-doped AlN with conductivity of 0.3 (Ω cm)−1 and electron concentration of 2 × 1018 cm−3 was realized via a non-equilibrium process comprising ion implantation and annealing at a moderate thermal budget. Similar to a previously demonstrated shallow donor state in Si-implanted AlN, Ge implantation also showed a shallow donor behavior in AlN with an ionization energy ∼80 meV. Ge showed a 3× higher conductivity than its Si counterpart for a similar doping level. Photoluminescence spectroscopy indicated that higher conductivity for Ge-doped AlN was achieved primarily due to lower compensation. This is the highest n-type conductivity reported for AlN doped with Ge to date and demonstration of technologically useful conductivity in Ge-doped AlN. [ABSTRACT FROM AUTHOR]

The influence of the polarization field on the emission properties of the AlGaN-based quantum structures grown on AlN substrates was investigated as a function of well width, barrier width, and barrier height. A thin AlGaN well and a thin AlN barrier design reduced the polarization field to ∼0.5 MV/cm, resulting in an ultralow laser threshold of 3 kW/cm2 in an optically pumped configuration. These experimental results were used to validate the simulation. In the next step, a structure with Al0.7Ga0.3N barriers was designed to support carrier injection with a minimal loss in optical performance. This structure showed a threshold of 7 kW/cm2 under optical pumping and an estimated threshold current of 8 kA/cm2 for the electric injection. [ABSTRACT FROM AUTHOR]

Heteroepitaxial crystallographic tilt has been investigated as a possible strain‐relief mechanism in Al‐rich (Al>50%) AlGaN heteroepitaxial layers grown on single‐crystal (0001) AlN substrates with varying miscuts from 0.05° to 4.30°. The magnitude of the elastic lattice deformation‐induced tilt increases monotonically with the miscut angle, tightly following the Nagai tilt model. Although tilt angles as high as 0.1° are recorded, reciprocal space mapping (RSM) broadening and wafer bow measurements do not show any significant changes as a function of the heteroepitaxial tilt angle. While crystallographic tilting has been shown to be effective in controlling strain in some other heteroepitaxial systems, it does not provide any appreciable strain relief of the compressive strain in AlGaN/AlN heteroepitaxy. [ABSTRACT FROM AUTHOR]

Herein, Al‐rich AlGaN‐based avalanche photodiodes (APDs) grown on single crystal AlN substrates high ultraviolet‐C sensitivity for λ < 200 nm are fabricated, while exhibiting blindness to λ > 250 nm. A maximum quantum efficiency of 68% and peak gain of 320 000 are estimated resulting in a figure of merit of ≈220 000 in devices with ϕ = 100 μm. As expected, a decrease in gain with increase in device size is observed and a gain of ≈20 000 is estimated in devices with ϕ = 400 μm. Overall, two orders of magnitude higher performance are observed in APDs on single crystal AlN substrates compared to those on sapphire. [ABSTRACT FROM AUTHOR]

We report on the absence of strain relaxation mechanism in Al0.6Ga0.4N epilayers grown on (0001) AlN substrates for thickness as large as 3.5 μm, three-orders of magnitude beyond the Matthews–Blakeslee critical thickness for the formation of misfit dislocations (MDs). A steady-state compressive stress of 3–4 GPa was observed throughout the AlGaN growth leading to a large lattice bow (a radius of curvature of 0.5 m−1) for the thickest sample. Despite the large lattice mismatch-induced strain energy, the epilayers exhibited a smooth and crack-free surface morphology. These results point to the presence of a large barrier for nucleation of MDs in Al-rich AlGaN epilayers. Compositionally graded AlGaN layers were investigated as potential strain relief layers by the intentional introduction of MDs. While the graded layers abetted MD formation, the inadequate length of these MDs correlated with insignificant strain relaxation. This study emphasizes the importance of developing strain management strategies for the implementation of the single-crystal AlN substrate platform for III-nitride deep-UV optoelectronics and power electronics. [ABSTRACT FROM AUTHOR]

We demonstrate controlled Si doping in the low doping range of 5 Ă— 1015â€"2.5 Ă— 1016 cmâˆ'3 with mobility >1000 cm2 Vâˆ'1 sâˆ'1 in GaN films grown by metalorganic chemical vapor deposition. The carbon-related compensation and mobility collapse were prevented by controlling the electrochemical potential near the growth surface via chemical potential control (CPC) and defect quasi-Fermi level (dQFL) point-defect management techniques. While the CPC was targeted to reduce the net CN concentration, the dQFL control was used to reduce the fraction of C atoms with the compensating configuration, i.e. C N âˆ' 1. The low compensating acceptor concentration was confirmed via temperature-dependent Hall effect analysis and capacitanceâ€"voltage measurements. [ABSTRACT FROM AUTHOR]

The interfaces of m- and c-plane AlN with metals of different work functions and electro-negativities were characterized and the Schottky barrier heights were measured. The Schottky barrier height was determined by measuring the valence band maximum (VBM) with respect to the Fermi level at the surface (interface) before (after) metallization. VBM determination included accurate modeling and curve fitting of density of states at the valence band edge with the XPS data. The experimental behavior of the barrier heights could not be explained by the Schottky-Mott model and was modeled using InterFace-Induced Gap States (IFIGS). A slope parameter (SX) was used to incorporate the density of surface states and is a measure of Fermi level pinning. The experimental barriers followed theoretical predictions with a barrier height at the surface Fermi level (Charge neutrality level (CNL)) of ∼2.1 eV (∼2.7 eV) on m-plane (c-plane) and SX∼0.36 eV/Miedema unit. Slope parameter much lower than 0.86 implied a surface/interface states dominated behavior with significant Fermi level pinning and the measured barrier heights were close to the CNL. Titanium and zirconium provided the lowest barriers (1.6 eV) with gold providing the highest (2.3 eV) among the metals analyzed on m-plane. It was consistently found that barrier heights decreased from metal polar to non-polar surfaces, in general, due to an increasing CNL. The data indicated that charged IFIGS compensate spontaneous polarization charge. These barrier height and slope parameter measurements provided essential information for designing Schottky diodes and other contact-based devices on AlN. [ABSTRACT FROM AUTHOR]

We demonstrate Si-implanted AlN with high conductivity (>1 Ω−1 cm−1) and high carrier concentration (5 × 1018 cm−3). This was enabled by Si implantation into AlN with a low threading dislocation density (TDD) (<103 cm−2), a non-equilibrium damage recovery and dopant activation annealing process, and in situ suppression of self-compensation during the annealing. Low TDD and active suppression of VAl-nSiAl complexes via defect quasi Fermi level control enabled low compensation, while low-temperature, non-equilibrium annealing maintained the desired shallow donor state with an ionization energy of ∼70 meV. The realized n-type conductivity and carrier concentration are over one order of magnitude higher than that reported thus far and present a major technological breakthrough in doping of AlN. [ABSTRACT FROM AUTHOR]

We demonstrate high p-type conductivity and hole concentrations >1018 cm−3 in Mg-implanted GaN. The implantation was performed at room temperature and by post-implantation annealing at 1 GPa of N2 and in a temperature range of 1200–1400 °C. The high pressure thermodynamically stabilized the GaN surface without the need of a capping layer. We introduce a "diffusion budget," related to the diffusion length, as a convenient engineering parameter for comparing samples annealed at different temperatures and for different times. Although damage recovery, as measured by XRD, was achieved at relatively low diffusion budgets, these samples did not show p-type conductivity. Further analyses showed heavy compensation by the implantation-induced defects. Higher diffusion budgets resulted in a low Mg ionization energy (∼115 meV) and almost complete Mg activation. For even higher diffusion budgets, we observed significant loss of Mg to the surface and a commensurate reduction in the hole conductivity. High compensation at low diffusion budgets and loss of Mg at high diffusion budgets present a unique challenge for shallow implants. A direct control of the formation of compensating defects arising from the implantation damage may be necessary to achieve both hole conductivity and low Mg diffusion. [ABSTRACT FROM AUTHOR]

The effective refractive index in optically-pumped 265 nm AlGaN-based lasers is assessed from the spacing of the longitudinal cavity modes in short laser cavities. It is found that the effective refractive index is significantly higher than the value estimated from the Sellmeier equation (n = 2.5) and reaches values of 2.9 and 3.2 for structures with 3 and 15 quantum wells, respectively. These results indicate that the Sellmeier equation underestimates the effective refractive index in AlGaN-based laser structures and that a different approach is needed for successful mid-UV laser modeling and design. [ABSTRACT FROM AUTHOR]

We demonstrate Si as a shallow donor in aluminum nitride (AlN) with an ionization energy of ∼70 meV. The shallow state was achieved by ion implantation of Si into homoepitaxial AlN and a low thermal budget damage recovery and activation process. These results demonstrate that the DX formation may be a kinetically limited process, though being a non-equilibrium process, preventing the Si donor from relaxing to the deep donor state. The room temperature conductivity was measured to be ∼0.05 Ω−1 cm−1, which is one order of magnitude higher than what has been reported for the epitaxially doped or implanted AlN. [ABSTRACT FROM AUTHOR]

The evolution of defects due to high‐pressure annealing of magnesium ion‐implanted epitaxial GaN grown on high‐quality GaN substrates is investigated. Changes in the implant‐induced strain are quantified as a function of annealing temperature and time. After annealing at 1300 °C for 10 min, the implant‐induced strain is fully relieved and accompanied by the presence of extended defects such as basal plane stacking faults and prismatic loops. Approximately one‐third of the original implant‐induced strain remains after annealing at 700 °C, and 5% of the original strain remains at 1000 °C for 100 min. In all cases, nearly all of the recovered strain occurs within first few minutes of annealing. A prominent increase in the asymmetric (101¯4) triple axis X‐ray rocking curve full width at 0.01 maximum (FW0.01M) is observed after annealing at 1300 °C for 10 min. After annealing at 1300 °C for 100 min, a subsequent decrease in FW0.01M is correlated with a reduction of the extended defect density from 4 × 108 to 3 × 107 cm−2, determined through transmission electron microscope (TEM) measurements. Further reduction in the density of the extended defects by optimizing annealing temperature and time is expected to improve the performance of GaN‐based vertical power devices. [ABSTRACT FROM AUTHOR]

We demonstrate large area (25 000 μm2) Al-rich AlGaN-based avalanche photodiodes (APDs) grown on single crystal AlN substrates operating with differential (the difference in photocurrent and dark current) signal gain of 100 000 at 90 pW (<1 μW cm−2) illumination with very low dark currents <0.1 pA at room temperature under ambient light. The high gain in large area AlGaN APDs is attributed to a high breakdown voltage at 340 V, corresponding to very high breakdown fields ∼9 MV cm−1 as a consequence of low threading and screw dislocation densities < 103 cm−2. The maximum charge collection efficiency of 30% was determined at 255 nm, corresponding to the bandgap of Al0.65Ga0.35N, with a response of 0.06 A/W. No response was detected for λ > 280 nm, establishing solar blindness of the device. [ABSTRACT FROM AUTHOR]

In this work, we determine the dependence of the defect transition energies, electronic bands, and surface charge neutrality levels in AlGaN. With Vacuum level as reference, we show that energy transitions of localized defects and the surface Fermi level are independent of the alloy composition as electronic bands diverge with the increase in the bandgap as a function of alloy composition. The invariance of localized states on the alloy composition creates a convenient internal reference energy with respect to which other energy states may be measured. We demonstrate a higher generality to the universality rule with the independence of deep transition states of otherwise shallow donor type defects [(+1/+3) transition for VN] and defect complexes (CN+SiIII) in addition to the earlier predicted independent nature of mid-gap states when they are either the antibonding state between cationic impurities and host anion or acceptors at anion sites. [ABSTRACT FROM AUTHOR]

We report on fundamental structural and optical properties of lateral polarity junctions in GaN. GaN with Ga- to N-polar junctions was grown on sapphire using an AlN buffer layer. Results from scanning electron microscopy and Raman spectroscopy measurements indicate a superior quality of the Ga-polar GaN. An extremely strong luminescence signal is observed at the inversion domain boundary (IDB). Temperature dependent micro photoluminescence measurements are used to reveal the recombination processes underlying this strong emission. At 5 K the emission mainly arises from a stripe along the inversion domain boundary with a thickness of 4-5 μm. An increase of the temperature initially leads to a narrowing to below 2 μm emission area width followed by a broadening at temperatures above 70 K. The relatively broad emission area at low temperatures is explained by a diagonal IDB. It is shown that all further changes in the emission area width are related to thermalization effects of carriers and defects attracted to the IDB. The results are successfully used to confirm a theoretical model for GaN based lateral polarity junctions. Due to the strong and pronounced emission of IDBs even at elevated temperatures, it is demonstrated that lateral polarity junctions exhibit a strong potential for future high efficiency devices. [ABSTRACT FROM AUTHOR]

A characterization procedure was developed to determine the alloy composition and strain state of AlxGa1-xN/GaN(0

The article presents a new technique, which can be employed for the characterization of the composition, as well as the relaxation of the different [Al.sub.x][Ga.sub.1-x]N(0 < x < 1) layers grown on GaN/sapphire templates. The bimodal nature of the relaxation distribution of the layers is also analyzed.

Compensating point defect reduction in wide bandgap semiconductors is possible by above bandgap illumination based defect quasi Fermi level (dQFL) control. The point defect control technique employs excess minority carriers that influence the dQFL of the compensator, increase the corresponding defect formation energy, and consequently are responsible for point defect reduction. Previous studies on various defects in GaN and AlGaN have shown good agreement with the theoretical model, but no direct evidence for the role of minority carriers was provided. In this work, we provide direct evidence for the role of minority carriers in reducing point defects by studying the predicted increase in work done against defect (CN-1) formation with the decrease in the Fermi level (free carrier concentration) in Si doped GaN at a constant illumination intensity. Comparative defect photoluminescence measurements on illuminated and dark regions of GaN show an excellent quantitative agreement with the theory by exhibiting a greater reduction in yellow luminescence attributed to CN-1 at lower doping, thereby providing conclusive evidence for the role of the minority carriers in Fermi level control-based point defect reduction. [ABSTRACT FROM AUTHOR]

A high free hole concentration in III-nitrides is important for next generation optoelectronic and high power electronic devices. The free hole concentration exceeding 1018 cm-3 and resistivity as low as 0.7 Ωcm are reported for p-GaN layers grown by metalorganic vapor phase epitaxy on single crystal AlN substrates. Temperature dependent Hall measurements confirmed a much lower activation energy, 60–80mV, for p-GaN grown on AlN as compared to sapphire substrates; the lowering of the activation energy was due to screening of Coulomb potential by free carriers. It is also shown that a higher doping density (more than 5×1019 cm-3) can be achieved in p-GaN/AlN without the onset of self-compensation. [ABSTRACT FROM AUTHOR]

In this work, the Fermi level and band alignment at c-plane surfaces and interfaces of AlGaN thin films grown on sapphire and native single crystalline AlN substrates were analyzed via x-ray photoelectron spectroscopy. The dependence of charge neutrality level (CNL) on Al composition is found to be linear with n-type Schottky barrier heights (Φbn) exhibiting an overall quadratic behavior due to bandgap bowing. A general theoretical expression for Schottky barrier height on AlGaN is determined as a function of Al composition and metal electronegativity utilizing the interface induced gap states (IFIGS) model and is corroborated with current-voltage (I-V) characterization on Ni-based Schottky diodes. The measured CNLs were used to determine the conduction and valence band offsets in AlGaN hetero-junctions according to the IFIGS and were found to be split approximately 2/3 and 1/3 of the bandgap, respectively, at interfaces with AlGaN having comparable Al and Ga concentrations. Nonlinearities in Φbn result in an increase (>2/3) and decrease (<2/3) of the conduction band split at AlN/AlGaN and GaN/AlGaN interfaces, respectively. Characterization of core level binding energies revealed a composition-independent surface work function. Consequently, electron affinity is found to be a linear function of the barrier height at the CNL and band offsets determined via IFIGS and Anderson's rule were found to be identical. The origin of the bandgap bowing arising in the conduction band is proposed. [ABSTRACT FROM AUTHOR]

Since the band ordering in AlGaN has a profound effect on the performance of UVC light emitting diodes (LEDs) and even determines the feasibility of surface emitting lasers, the polarization properties of emitted light from c-oriented AlGaN and AlGaN-based laser structures were studied over the whole composition range, as well as various strain states, quantum confinements, and carrier densities. A quantitative relationship between the theoretical valence band separation, determined using k•p theory, and the experimentally measured degree of polarization is presented. Next to composition, strain was found to have the largest influence on the degree of polarization while all other factors were practically insignificant. The lowest crossover point from the transverse electric to transverse magnetic polarized emission of 245nm was found for structures pseudomorphically grown on AlN substrates. This finding has significant implications toward the efficiency and feasibility of surface emitting devices below this wavelength. [ABSTRACT FROM AUTHOR]

AlGaN lateral polarity structures (LPS) with varying Al composition, have been fabricated by metalorganic chemical vapour deposition on LPS templates containing µm size domains. III-metal and N-polar AlGaN domains have been grown on LT-AlN and c-sapphire domains, respectively. LPS characterization by SEM and AFM reveals two major effects when the Al composition has been varied: (a) A high Al content leads to columnar growth within N-polar domains and (b) a height difference between the polar domains can be observed for low Al compositions towards III-polarity. The surface quality of the III-polar domains is not effected by the Al composition. The surface roughness of N-polar domains decreases for lower Al compositions. The high periodicity of the polar domains and the high quality of the boundary between domains suggest a high potential of AlGaN LPS to be used as lateral wave guides for quasi phase matching. [ABSTRACT FROM AUTHOR]

A Fermi-level control scheme for point defect management using above-bandgap UV illumination during growth is presented. We propose an extension to the analogy between the Fermi level and the electrochemical potential such that the electrochemical potential of a charged defect in a material with steady-state populations of free charge carriers may be expressed in terms of the quasi-Fermi levels. A series of highly Si-doped Al065Ga035N films grown by metalorganic chemical vapor deposition with and without UV illumination showed that samples grown under UV illumination had increased free carrier concentration, free carrier mobility, and reduced midgap photoluminescence all indicating a reduction in compensating point defects. [ABSTRACT FROM AUTHOR]

A surface preparation technique has been developed for non-polar m-plane aluminum nitride (AlN) single crystalline substrates. Chemical surface treatments were conducted on chemomechanically polished m-plane oriented AlN substrate surfaces. X-ray photoelectron spectroscopy was used to characterize the surface chemistry after each processing step. A layer of mixed aluminum oxide-hydroxide was identified on ambient air-exposed surfaces. Analysis of the oxygen core level spectra showed oxygen in three bonding states, identified by the binding energies and relative separation of the fitted peaks as O2−, OH− and H2O. Molar ratios of different components showed the oxide to be dominantly bonded in the OH− state. Wet etching reduced the amount of surface oxides. Ammonia annealing at 1100 °C converted the aluminum oxide-hydroxide layer to AlN. Although the overall amount of the oxide on the surface was reduced by surface treatments, the nature of the oxide remained predominantly of the OH−character. (© 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [ABSTRACT FROM AUTHOR]

Growth and characterization of AlN based lateral polarity structures (LPS) are presented. The LPS were grown by MOCVD using patterned low temperature AlN/sapphire substrates: the Al-polar and N-polar AlN grew on AlN buffer layer and nitrided sapphire, respectively. AFM images showed a height difference between the two adjacent domains of different polarity on the order of 30 nm, which was equivalent to the low temperature AlN buffer layer thickness. SEM images provided an insight in the growth mode of the two polarities. It was shown that Al-polar AlN grew two-dimensionally, leading to a smooth well coalesced layer, while N-polar AlN grew primarily three-dimensionally, leading to a columnar structure. This difference in the growth mode led to different properties of domains with opposite polarity, including strain and defect incorporation, as observed by X-ray diffraction, photoluminescence, and Raman spectroscopy measurements. Finally, an outlook on the applicability and future development of AlN-based LPS is given. (© 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim) [ABSTRACT FROM AUTHOR]

The control of the polarity of metalorganic chemical vapor deposition grown AlN on sapphire is demonstrated. Al-polar and N-polar AlN is grown side-by-side yielding a lateral polarity structure. Scanning electron microscopy measurements reveal a smooth surface for the Al-polar and a relatively rough surface for the N-polar AlN domains. Transmission electron microscopy shows mixed edge-screw type dislocations with polarity-dependent dislocation bending. Raman spectroscopy reveals compressively strained Al-polar and relaxed N-polar domains. The near band edge luminescence consists of free and bound excitons which are broadened for the Al-polar AlN. Relaxation, better optical quality, and dislocation bending in the N-polar domains are explained by the columnar growth mode. [ABSTRACT FROM AUTHOR]

Using contemporary Chinese and Hong Kong cinema, the large body of writing on media emanating from Koolhaas and his atelier, and the headquarters for China Central Television as its primary touchstones, this essay examines the relationship between the current media environment in East Asia and the architectural practice and theory produced by Koolhaas. The paper argues that his virtuoso designs and enormously productive critical work reach an impasse at precisely the moment when his conception of cinema is exhausted and he embraces the increasingly influential theoretical model drawn from digital media. While his notion of the generic city is modeled on the film studio set, with its utterly flexible and ephemeral structures expanded to the scale of the city, and his more recent structures embody the promises of a network society, Koolhaas fails to consider other image-making practices that remain vibrant and rely on diametrically opposed conceptions of the moving image, most notably the documentary-derived cinema of film-makers like Jia Zhangke. [ABSTRACT FROM AUTHOR]

In the mid 1980s Michelangelo Merisi da Caravaggio's work experienced a renaissance, as a major exhibition in New York in 1985 and a series of critical studies returned the artist to the centre of European and American art historical discourse. A new generation of artists and critics was forced to reconsider the painter's relevance, after an era dominated by minimalism and abstract expressionism, to the broader social project of discovering alternative histories of the early modern world. Debates amongst artists and critics surrounding the Metropolitan exhibition asked whether Caravaggio is a tutor figure for the successors of abstract expressionism, or a poor draughts man with a worse disposition, whose revival merely confirms that "375 years have not dimmed [his work's] power to be showy, pushy, and hollow," or one of the last exponents of a tradition of artistic craftsmanship, which, far from contemporary, "sadly is now past beyond recall." Despite the vast separation in time between Caravaggio's late 16th-century and early 17th-century Italy and the moment of his revival, his artwork and biography were conscripted into a variety of contemporary struggles.

Compensation effects in metal organic chemical vapour deposition grown GaN doped with magnesium are investigated with Raman spectroscopy and photoluminescence measurements. Examining the strain sensitive E2(high) mode, an increasing compressive strain is revealed for samples with Mg-concentrations lower than 7 × 1018 cm-3. For higher Mg-concentrations, this strain is monotonically reduced. This relaxation is accompanied by a sudden decrease in crystal quality. Luminescence measurements reveal a well defined near band edge luminescence with free, donor bound, and acceptor bound excitons as well as a characteristic donor acceptor pair (DAP) luminescence. Following recent results, three acceptor bound excitons and donor acceptor pairs are identified. Along with the change of the strain, a strong modification in the luminescence of the dominating acceptor bound exciton and DAP luminescence is observed. The results from Raman spectroscopy and luminescence measurements are interpreted as fingerprints of compensation effects in GaN:Mg leading to the conclusion that compensation due to defect incorporation triggered by Mg-doping already affects the crystal properties at doping levels of around 7 × 1018 cm-3. Thereby, the generation of nitrogen vacancies is introduced as the driving force for the change of the strain state and the near band edge luminescence. [ABSTRACT FROM AUTHOR]

It was demonstrated that Ge has the same effect as Si on the strain evolution in n-type GaN as measured by x-ray diffraction. Dislocation inclination, which causes tensile strain in n-type GaN, was clearly observed by transmission electron microscopy where Ge doping was introduced during epitaxial growth. This result is explained by the Fermi level effect model that indicates dislocation inclination due to the climbing process through Ga vacancies. Therefore, there is no dependence of dislocation inclination on dopant species. [ABSTRACT FROM AUTHOR]