Search

This study introduces a novel approach to synthesising a three-dimensional (3D) micro-nanostructured amorphous biosilica. The biosilica is coated with cerium oxide nanoparticles obtained from laboratory-grown unicellular photosynthetic algae (diatoms) doped metabolically with cerium. This unique method utilises the ability of diatom cells to absorb cerium metabolically and deposit it on their silica exoskeleton as cerium oxide nanoparticles. The resulting composite (Ce-DBioSiO2) combines the unique structural and photonic properties of diatom biosilica (DBioSiO2) with the functionality of immobilised CeO2 nanoparticles. The kinetics of the cerium metabolic insertion by diatom cells and the physicochemical properties of the obtained composites were thoroughly investigated. The resulting Ce-DBioSiO2 composite exhibits intense Stokes fluorescence in the violet–blue region under ultraviolet (UV) irradiation and anti-Stokes intense violet and faint green emissions under the 800 nm near-infrared excitation with a xenon lamp at room temperature in an ambient atmosphere. [ABSTRACT FROM AUTHOR]

Modern technology's development is also towards using microorganisms as micro-factories of biomaterials with unique properties and combining the original properties of biosilica extracted from diatoms (microalgae) together with immobilised silver and cerium in nanoparticle forms allowed to obtain a modern composite material with antibacterial activity. The synthesised composites containing heteroepitaxially growing Ag/AgCl/CeO2 complex nanoparticles were studied using different types of instrumental analysis. SEM-EDX and XRD analysis allowed the qualitative and quantitative determination of the elements present and their forms in the composites. TEM permitted analysis of information about the created nanoparticles shape, size and structure specificity. The possible mechanism of nanoparticle formation was suggested. Antibacterial properties of synthesised composites were characterised using a minimum inhibitory concentration test on six selected bacterial strains. Diatomaceous biosilica containing heteroepitaxially growing silver chloride, metallic silver, and cerium (IV) oxide nanoparticles have been prepared for the first time. The proposed method for synthesising composites did not use toxic reagents, making it environmentally friendly. [ABSTRACT FROM AUTHOR]

The 3D (three-dimensional) micro–nanostructured diatom biosilica obtained from cultivated diatoms was used as a support to immobilize epitaxially growing AgCl-Ag hybrid nanoparticles ((Ag-AgCl)NPs) for the synthesis of nanocomposites with antimicrobial properties. The prepared composites that contained epitaxially grown (Ag-AgCl)NPs were investigated in terms of their morphological and structural characteristics, elemental and mineral composition, crystalline forms, zeta potential, and photoluminescence properties using a variety of instrumental methods including SEM (scanning electron microscopy), TEM (transmission electron microscopy), EDX (energy-dispersive X-ray spectroscopy), XRD (X-ray powder diffraction), zeta-potential measurement, and photoluminescence spectroscopy. The content of (AgCl-Ag)NPs in the hybrid composites amounted to 4.6 mg/g and 8.4 mg/g with AgClNPs/AgNPs ratios as a percentage of 86/14 and 51/49, respectively. Hybrid nanoparticles were evenly dispersed with a dominant size of 5 to 25 nm in composite with an amount of 8.4 mg/g of silver. The average size of the nanoparticles was 7.5 nm; also, there were nanoparticles with a size of 1–2 nm and particles that were 20–40 nm. The synthesis of (Ag-AgCl)NPs and their potential mechanism were studied. The MIC (the minimum inhibitory concentration method) approach was used to investigate the antimicrobial activity against microorganisms Klebsiella pneumoniae, Escherichia coli, and Staphylococcus aureus. The nanocomposites containing (Ag-AgCl)NPs and natural diatom biosilica showed resistance to bacterial strains from the American Type Cultures Collection and clinical isolates (diabetic foot infection and wound isolates). [ABSTRACT FROM AUTHOR]

In the pursuit of innovative solutions for modern technologies, particularly in the design and production of new micro/nanostructured materials, microorganisms acting as "natural microtechnologists" can serve as a valuable source of inspiration. This research focuses on harnessing the capabilities of unicellular algae (diatoms) to synthesize hybrid composites composed of AgNPs/TiO2NPs/pyrolyzed diatomaceous biomass (AgNPs/TiO2NPs/DBP). The composites were consistently fabricated through metabolic (biosynthesis) doping of diatom cells with titanium, pyrolysis of the doped diatomaceous biomass, and chemical doping of the pyrolyzed biomass with silver. To characterize the synthesized composites, their elemental and mineral composition, structure, morphology, and photoluminescent properties were analysed using techniques such as X-ray diffraction, scanning and transmission electron microscopy, and fluorescence spectroscopy. The study revealed the epitaxial growth of Ag/TiO2 nanoparticles on the surface of pyrolyzed diatom cells. The antimicrobial potential of the synthesized composites was evaluated using the minimum inhibitory concentration (MIC) method against prevalent drug-resistant microorganisms, including Staphylococcus aureus, Klebsiella pneumonia, and Escherichia coli, both from laboratory cultures and clinical isolates. [ABSTRACT FROM AUTHOR]

Hydroxyapatite (HA) layers are appropriate biomaterials for use in the modification of the surface of implants produced inter alia from a Ti6Al4V alloy. The issue that must be solved is to provide implants with appropriate biointegration properties, enabling the permanent link between them and bone tissues, which is not so easy with the HA layer. Our proposition is the use of the intermediate layer ((IL) = TiO2, and titanate layers) to successfully link the HA coating to a metal substrate (Ti6Al4V). The morphology, structure, and chemical composition of Ti6Al4V/IL/HA systems were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy-dispersive X-ray spectrometry (EDS). We evaluated the apatite-forming ability on the surface of the layer in simulated body fluid. We investigated the effects of the obtained systems on the viability and growth of human MG-63 osteoblast-like cells, mouse L929 fibroblasts, and adipose-derived human mesenchymal stem cells (ADSCs) in vitro, as well as on their osteogenic properties. Based on the obtained results, we can conclude that both investigated systems reflect the physiological environment of bone tissue and create a biocompatible surface supporting cell growth. However, the nanoporous TiO2 intermediate layer with osteogenesis-supportive activity seems most promising for the practical application of Ti6Al4V/TiO2/HA as a system of bone tissue regeneration. [ABSTRACT FROM AUTHOR]

Functionalized carbon nanotubes are interesting, promising and unique delivery systems for anticancer drugs, which are now in the spotlight of nanomedicine. Connecting nanotubes with anticancer drugs or new compounds with anticancer properties aims at improving their stability, efficiency and reduces the toxic side effects of cancer treatment. In our research, we are interested in connecting functionalized MWCNTs-NH2 with [InH][trans-RuCl4(In)2], (KP1019) which is one of the most promising anticancer ruthenium(III) drug candidates, known mainly as a cytotoxic agent for the treatment of platinum-resistant colorectal cancers. As a result of the amidation of MWCNTs (1), MWCNTs-NH2 (2) were obtained. Then, they were modified with [InH][RuCl4(In)2] (4) and the nanosystem [MWCNT-NH3+][RuCl4(In)2−] (3) was obtained. The characterization of the resulting products was performed using IR, Raman spectroscopy, thermal gravimetric, XRD, STEM-EDX, ESI-MS, ICP-MS, and XPS analyses. The cytotoxic activity has been tested on human lung carcinoma (A549), chronic myelogenous leukemia (K562) and human cervix carcinoma (HeLa) cells which showed the higher toxicity of the nanosystem than the ruthenium complex. [ABSTRACT FROM AUTHOR]

Novel visible light responsive materials for water splitting are essential for the efficient conversion of solar energy into hydrogen bond energy. Among other semiconductors, gadolinium orthovanadate has appropriate conduction and valence band edges positioned to split water molecules and a narrow band gap that allows the use of visible light for hydrogen generation. Thus, we present here that hydrogen evolution under visible light (λ ＞ 420 nm) could be accomplished using hierarchical 3D GdVO4 particles, obtained by a simple, one pot hydrothermal synthesis. We found that applying various reaction components, such as EDTA-Na2 and EDTA, and adjusting the pH of the solution allow one to tune the shape of GdVO4 (such as short nanowires, long nanowires, short nanorods, long nanorods, nanoparticles and spheres – all having a tetragonal crystal structure) as well as optical and photocatalytic properties. The highest ability to photocatalytically split methanol solution into hydrogen under UV-Vis irradiation was detected for the long nanowire sample (42 μmol h−1), having almost 11 times higher efficiency in comparison with the weakest sample – short nanowires. In addition, GdVO4 spheres generated H2 more than 2 times (5.75 μmol h−1) in comparison with the short nanorod sample (2.5 μmol h−1) under visible light excitation. Photostable in three-hour work cycles, long nanowires and spheres were even able to generate hydrogen from pure water, reaching values of 17 and 3 μmol under UV-Vis and Vis light, respectively. [ABSTRACT FROM AUTHOR]

V2O5-TiO2 mixed oxide nanotube (NT) layers were successfully prepared via the one-step anodization of Ti-V alloys. The obtained samples were characterized by scanning electron microscopy (SEM), UV-Vis absorption, photoluminescence spectroscopy, energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (DRX), and micro-Raman spectroscopy. The effect of the applied voltage (30-50 V), vanadium content (5-15 wt %) in the alloy, and water content (2-10 vol %) in an ethylene glycol-based electrolyte was studied systematically to determine their influence on the morphology, and for the first-time, on the photocatalytic properties of these nanomaterials. The morphology of the samples varied from sponge-like to highly-organized nanotubular structures. The vanadium content in the alloy was found to have the highest influence on the morphology and the sample with the lowest vanadium content (5 wt %) exhibited the best auto-alignment and self-organization (length = 1 _m, diameter = 86 nm and wall thickness = 11 nm). Additionally, a probable growth mechanism of V2O5-TiO2 nanotubes (NTs) over the Ti-V alloys was presented. Toluene, in the gas phase, was effectively removed through photodegradation under visible light (LEDs, λmax = 465 nm) in the presence of the modified TiO2 nanostructures. The highest degradation value was 35% after 60 min of irradiation. V2O5 species were ascribed as the main structures responsible for the generation of photoactive e- and h+ under Vis light and a possible excitation mechanism was proposed. [ABSTRACT FROM AUTHOR]

Vertically oriented, self-organized TiO2-MnO2 nanotube arrays were successfully obtained by one-step anodic oxidation of Ti-Mn alloys in an ethylene glycol-based electrolyte. The as-prepared samples were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), UV-Vis absorption, photoluminescence spectroscopy, X-ray diffraction (XRD), and micro-Raman spectroscopy. The effect of the applied potential (30-50 V), manganese content in the alloy (5-15 wt. %) and water content in the electrolyte (2-10 vol. %) on the morphology and photocatalytic properties was investigated for the first time. The photoactivity was assessed in the toluene removal reaction under visible lighţ using low-powered LEDs as an irradiation source (λmax = 465 nm). Morphology analysis showed that samples consisted of auto-aligned nanotubes over the surface of the alloy, their dimensions were: diameter = 76-118 nm, length = 1.0-3.4 μm and wall thickness = 8-11 nm. It was found that the increase in the applied potential led to increase the dimensions while the increase in the content of manganese in the alloy brought to shorter nanotubes. Notably, all samples were photoactive under the influence of visible light and the highest degradation achieved after 60 min of irradiation was 43%. The excitation mechanism of TiO2-MnO2 NTs under visible light was presented, pointing out the importance of MnO2 species for the generation of e- and h+. [ABSTRACT FROM AUTHOR]

Filtration properties of membranes obtained by deposition of a few layer graphene oxide onto a polyamide support, with and without borate treatment, were examined. Filtrations of water, dilute solutions of electrolytes (Na2 SO4, NaCl, MgSO4, MgCl2 ), and dyes (bromophenol blue, eriochrome black T) were performed. It was found that the observed electrolyte retention series (Na2 SO4 > NaCl > MgSO4 > MgCl2 ) was in accordance with the Donnan exclusion theory. The membrane treated with borate and of higher graphene oxide load showed higher retention of sulfates than the untreated one. Despite of lower molecular weight, eriochrome black T was practically completely rejected by both types of membranes, contrary to bromophenol blue, irrespectively of its form (undissociated – retention 68%, dissociated – 85%). [ABSTRACT FROM AUTHOR]

We investigated Fe-phases of iron complexes embedded in nonfunctionalized (as-prepared) and functionalized multi-wall carbon nanotubes (MWCNTs). Mössbauer spectroscopy is a very sensitive tool to study chemical states of iron compounds embedded in MWCNTs. It showed that the chemical treatment of the as-prepared MWCNTs caused release of about 84% of iron and modification of the remaining iron compounds. In as-prepared and carboxylated MWCNTs almost 80 and 75% of iron complexes in a form of Fe3C exhibited magnetic ordering even at room temperature, respectively. In MWCNT-COONH4 only 50% of such iron compounds showed local magnetic ordering. In all cases about 2% of magnetic α-Fe fraction was detected. Through the dc magnetization and transmission electron microscopy (TEM) measurements it was proved that cementite nanoparticles formed agglomerates and their sizes were larger than 10 nm. STM measurements indicated increased homogeneity of the surface electric properties in the case of chemically treated carbon nanotubes. [ABSTRACT FROM AUTHOR]

The results of treating commercial granulated activated carbons with ozone, both gaseous and dissolved in water, were analyzed. The original carbons (Filtrasorb-300 and Carbsorb-38) were carefully flushed with distilled water to remove any water-soluble impurities. For comparison, each of the washed activated carbons was treated separately with aqueous hydrogen peroxide. The following procedures were applied to assess the effects of contact between each carbon and the oxidizing agents: thermogravimetry, alkalimetry, voltammetry, EDX and FT-IR methods to illustrate changes in the surface chemistry, and nitrogen low-temperature adsorption to show up any possible changes in the porous structure. Ozone dissolved in water exhibited the lowest oxidative strength - EDX and FT-IR spectroscopy revealed only a slight oxidation of the Filtrasorb-300 surface layer. Despite its smaller specific area, this carbon surface exhibited greater roughness and was more susceptible to oxidation. The liquid-phase adsorption isotherms of p-chlorophenol from aqueous solution onto this carbon showed that surface oxygen reduced the extent of adsorption. The experimental data were best fitted by the Langmuir isotherm model. [ABSTRACT FROM AUTHOR]

Reduced graphene oxide (rGO) was prepared by chemical reduction of graphene oxide (GO) (with a modified Hummers method) in aqueous solutions of hydrazine (N2H4), formaldehyde (CH2O), formic acid (HCO2H) accompanied by a microwave treatment at 250 °C (MWT) by a high pressure microwave reactor (HPMWR) at 55 bar. The substrates and received products were investigated by TEM, XRD, Raman and IR spectroscopies, XPS, XAES and REELS. MWT assisted reduction using different agents resulted in rGOs of a large number of vacancy defects, smaller than at GO surface C sp3 defects, oxygen groups and interstitial water, interlayer distance and diameter of stacking nanostructures (flakes). The average number of flake layers obtained from XRD and REELS was consistent, being the smallest for CH2O and then increasing for HCO2H and N2H4. The number of layers in rGOs increases with decreasing content of vacancy, C sp3 defects, oxygen groups, water and flake diameter. MWT conditions facilitate formation of vacancies and additional hydroxyl, carbonyl and carboxyl groups at these vacancies, provide no remarkable modification of flake diameter, what results in more competitive penetration of reducing agent between the interstitial sites than via vacancies. MWT reduction of GO using a weak reducing agent (CH2O) provided rGO of 8 layers thickness. [ABSTRACT FROM AUTHOR]

The influence of the grinding process on the magnetic properties of as prepared and functionalized multiwall carbon nanotubes (MWCNTs) is presented. We have observed that 3 h mechanical grinding at 400 rpm in contrast to functionalization does not remove the iron contamination from MWCNTs. However, it changes the Fe chemical states. The magnetic properties of iron nanoparticles (Fe-NPs) embedded in the carbon matrix of MWCNTs have been analyzed in detail. We have proven that single-domain non-interacting Fe(C,O)-NPs enriched in the Fe3C phase (~10 nm) enclosed inside these nanotubes are responsible for their magnetic properties. Mechanical grinding revealed a unique impact of -COOH groups (compared to -COONH4 groups) on the magnetism of functionalized MWCNTs. In MWCNT-COOH ground in a steel mill, the contribution of the Fe2O3 and α-Fe phases increased while the content of the magnetically harder Fe3C phase decreased. This resulted in a 2-fold coercivity (Hc) decrease and saturation magnetization (MS) increase. A 2-fold remanence (Mr) decrease in MWCNT-COOH ground in an agate mill is related to the modified Fe(C,O)-NP magnetization dynamics. Comparison of the magnetostatic exchange and effective anisotropy length estimated for Fe(C,O)-NPs allows concluding that the anisotropy energy barrier is higher than the magnetostatic energy barrier. The enhanced contribution of surface anisotropy to the effective anisotropy constant and the unique effect of the -COOH groups on the magnetic properties of MWCNTs are discussed. The procedure for grinding carboxylated MWCNTs with embedded iron nanoparticles using a steel mill has a potential application for producing Fe-C nanocomposites with desired magnetic properties. [ABSTRACT FROM AUTHOR]

In search a hydrogen source, we synthesized TiO2-Cu-graphene composite photocatalyst for hydrogen evolution. The catalyst is a new and unique material as it consists of copper-decorated TiO2 particles covered tightly in graphene and obtained in a fluidized bed reactor. Both, reduction of copper from Cu(CH3COO) at the surface of TiO2 particles and covering of TiO2-Cu in graphene thin layer by Chemical Vapour Deposition (CVD) were performed subsequently in the flow reactor by manipulating the gas composition. Obtained photocatalysts were tested in regard to hydrogen generation from photo-induced water conversion with methanol as sacrificial agent. The hydrogen generation rate for the most active sample reached 2296.27 µmol H2 h−1 gcat−1. Combining experimental and computational approaches enabled to define the optimum combination of the synthesis parameters resulting in the highest photocatalytic activity for water splitting for green hydrogen production. The results indicate that the major factor affecting hydrogen production is temperature of the TiO2-Cu-graphene composite synthesis which in turn is inversely correlated to photoactivity. [ABSTRACT FROM AUTHOR]

Herein we present a study on polymer-derived silicon oxycarbide (SiOC)/graphite composites for a potential application as an electrode in high power energy storage devices, such as Lithium-Ion Capacitor (LIC). The composites were processed using high power ultrasound-assisted sol-gel synthesis followed by pyrolysis. The intensive sonication enhances gelation and drying process, improving the homogenous distribution of the graphitic flakes in the preceramic blends. The physicochemical investigation of SiOC/graphite composites using X-ray diffraction, 29Si solid state NMR and Raman spectroscopy indicated no reaction occurring between the components. The electrochemical measurements revealed enhanced capacity (by up to 63%) at high current rates (1.86 A g−1) recorded for SiOC/graphite composite compared to the pure components. Moreover, the addition of graphite to the SiOC matrix decreased the value of delithiation potential, which is a desirable feature for anodes in LIC. [ABSTRACT FROM AUTHOR]

In this work, we report the synthesis of hydrated and non-crystalline WO3 flakes (WO3−x) via an environmentally friendly and facile water-based strategy. This method is described, in the literature, as exfoliation, however, based on the results obtained, we cannot say unequivocally that we have obtained an exfoliated material. Nevertheless, the proposed modification procedure clearly affects the morphology of WO3 and leads to loss of crystallinity of the material. TEM techniques confirmed that the process leads to the formation of WO3 flakes of a few nanometers in thickness. X-ray diffractograms affirmed the poor crystallinity of the flakes, while spectroscopic methods showed that the materials after exfoliation were abundant with the surface groups. The thin film of hydrated and non-crystalline WO3 exhibits a seven times higher specific capacitance (Cs) in an aqueous electrolyte than bulk WO3 and shows an outstanding long-term cycling stability with a capacitance retention of 92% after 1000 chronopotentiometric cycles in the three-electrode system. In the two-electrode system, hydrated WO3−x shows a Cs of 122 F g−1 at a current density of 0.5 A g−1. The developed supercapacitor shows an energy density of 60 Whkg−1 and power density of 803 Wkg−1 with a decrease of 16% in Csp after 10,000 cycles. On the other hand, WO3−x is characterized by inferior properties as an anode material in lithium-ion batteries compared to bulk WO3. Lithium ions intercalate into a WO3 crystal framework and occupy trigonal cavity sites during the electrochemical polarization. If there is no regular layer structure, as in the case of the hydrated and non-crystalline WO3, the insertion of lithium ions between WO3 layers is not possible. Thus, in the case of a non-aqueous electrolyte, the specific capacity of the hydrated and non-crystalline WO3 electrode material is much lower in comparison with the specific capacity of the bulk WO3-based anode material. [ABSTRACT FROM AUTHOR]

The effect of type (AgInS2, SnS, CuS2, Bi2S3) and amount (5, 10, 15 wt%) of quantum dots (QDs) on the surface properties and photocatalytic activity of QDs-sensitized TiO2 composite, was investigated. AgInS2, SnS, CuS2, Bi2S3 QDs were obtained by hot-injection, sonochemical, microwave, and hot-injection method, respectively. To characterize of as-prepared samples high-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), UV-Vis spectroscopy and photoluminescence (PL) emission spectroscopy were applied. The size of AgInS2, SnS, CuS2, Bi2S3 QDs were 12; 2–6; 2–3, and 1–2 nm, respectively. The QDs and QDs-sensitized TiO2 composites obtained have been tested in toluene degradation under LEDs light irradiation (λmax = 415 nm and λmax = 375 nm). For pristine QDs the efficiency of toluene degradation increased in the order of AgInS2 < Bi2S3 < CuS < SnS under 375 nm and AgInS2 < CuS < Bi2S3 < SnS under 415 nm. In the presence of TiO2/SnS QDs_15% composite, 91% of toluene was degraded after 1 h of irradiation, and this efficiency was about 12 higher than that for pristine QDs under 375 nm. Generally, building the TiO2/AgInS2 and TiO2/SnS exhibited higher photoactivity under 375 nm than the pristine TiO2 and QDs which suggests a synergistic effect between QDs and TiO2 matrix. [ABSTRACT FROM AUTHOR]

Novel Ln-MOF with microrods shape were successfully combined with ZnIn 2 S 4 (ZIS) microsphere and used for photocatalytic hydrogen generation under UV–Vis and visible light. The Ln-MOFs/ZIS system comprises lanthanide-carboxylate coordination networks (Tm and Gd as metal ions, and 1,3,5-benzenetricarboxylic acid (BTC) as the organic linker) deposited on ZnIn 2 S 4 microspheres. Effect of the amount of ((Tm,Gd)-BTC) (1, 5, 10 wt%) on the optical properties and photocatalytic hydrogen evolution performance was investigated. ZIS microsphere shows the marigold flower-like morphology and hexagonal polytopic crystal form. Our results proved that the combination of ZIS microsphere, Ln-MOF and Pt nanoparticles (NPs) caused significant enhancement in hydrogen generation. Amount of formed hydrogen was raised from 196.3 to 7782.1 μmol g−1 for pristine ZIS and ZIS decorated with 1% (Tm, Gd)-BTC/Pt under UV–Vis light, respectively. [Display omitted] • Novel composite of (Tm,Gd)-BTC with ZnIn 2 S 4 microsphere. • Highly efficient photocatalytic performance compared to ZnIn 2 S 4. • Amount of H 2 formed over ZIS/1%Ln-MOF/Pt was 11,866,57 μmol g−1 under UV–Vis. • 40 times greater photocatalytic H 2 evolution for ZIS/1%Ln-MOF/Pt than for ZIS/Pt. [ABSTRACT FROM AUTHOR]

One of the most important challenges in the fabrication of ordered tantalum pentaoxide (Ta2O5) nanotube arrays (NTs) via the electrochemical method is the formation of nanotubes that adhere well to the Ta substrate. In this paper, we propose a new protocol that allows tight-fitting Ta2O5 nanotubes to be obtained through the anodic oxidation of tantalum foil. Moreover, to enhance their activity in the photocatalytic reaction, in this study, they have been decorated by nontoxic bismuth sulfide (Bi2S3) quantum dots (QDs) via a simple successive ionic layer adsorption and reaction (SILAR) method. Transmission electron microscopy (TEM) analysis revealed that quantum dots with a size in the range of 6–11 nm were located both inside and on the external surfaces of the Ta2O5 NTs. The effect of the anodization time and annealing conditions, as well as the effect of cycle numbers in the SILAR method, on the surface properties and photoactivity of Ta2O5 nanotubes and Bi2S3/Ta2O5 composites have been investigated. The Ta2O5 nanotubes decorated with Bi2S3 QDs exhibit high photocatalytic activity in the toluene degradation reaction, i.e., 99% of toluene (C0 = 200 ppm) was degraded after 5 min of UV-Vis irradiation. Therefore, the proposed anodic oxidation of tantalum (Ta) foil followed by SILAR decorating allows a photocatalytic surface, ready to use for pollutant degradation in the gas phase, to be obtained. [ABSTRACT FROM AUTHOR]

TiO2/CuxOy nanotube (NT) arrays were synthesized using the anodization method in the presence of ethylene glycol and different parameters applied. The presence, morphology, and chemical character of the obtained structures was characterized using a variety of methods—SEM (scanning electron microscopy), XPS (X-ray photoelectron spectroscopy), XRD (X-ray crystallography), PL (photoluminescence), and EDX (energy-dispersive X-ray spectroscopy). A p-n mixed oxide heterojunction of Ti-Cu was created with a proved response to the visible light range and the stable form that were in contact with Ti. TiO2/CuxOy NTs presented the appearance of both Cu2O (mainly) and CuO components influencing the dimensions of the NTs (1.1–1.3 µm). Additionally, changes in voltage have been proven to affect the NTs’ length, which reached a value of 3.5 µm for Ti90Cu10_50V. Degradation of phenol in the aqueous phase was observed in 16% of Ti85Cu15_30V after 1 h of visible light irradiation (λ > 420 nm). Scavenger tests for phenol degradation process in presence of NT samples exposed the responsibility of superoxide radicals for degradation of organic compounds in Vis light region. Inactivation of bacteria strains Escherichia coli (E. coli), Bacillus subtilis (B. subtilis), and Clostridium sp. in presence of obtained TiO2/CuxOy NT photocatalysts, and Vis light has been studied showing a great improvement in inactivation efficiency with a response rate of 97% inactivation for E. coli and 98% for Clostridium sp. in 60 min. Evidently, TEM (transmission electron microscopy) images confirmed the bacteria cells’ damage. [ABSTRACT FROM AUTHOR]