Search

Oxygen reduction reaction (ORR) and oxygen evolutionc reaction (OER) are important chemical reactions for a rechargeable lithium–oxygen battery (LOB). Recently, high-entropy alloys and oxides have attracted much attention because they showed good electrocatalytic performance for oxygen evolution reaction (OER) and/or oxygen reduction reaction (ORR). In this study, we aimed to synthesize and characterize CoSn(OH)6 and two types of high-entropy perovskite hydroxides, that is, (Co0.2Cu0.2Fe0.2Mn0.2Mg0.2)Sn(OH)6 (CCFMMSOH) and (Co0.2Cu0.2Fe0.2Mn0.2Ni0.2)Sn(OH)6 (CCFMNSOH). TEM observation and XRD measurements revealed that the high-entropy hydroxides CCFMMSOH and CCFMNSOH had cubic crystals with sides of approximately 150–200 nm and crystal structures similar to those of perovskite-type CSOH. LSV measurement results showed that the high-entropy hydroxides CCFMMSOH and CCFMNSOH showed bifunctional catalytic functions for the ORR and OER. CCFMNSOH showed better catalytic performance than CCFMMSOH.

Lithium–air batteries (LABs) have a theoretically high energy density. However, LABs have some issues, such as low energy efficiency, short life cycle, and high overpotential in charge–discharge cycles. To solve these issues electrocatalytic materials were developed for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), which significantly affect battery performance. In this study, we aimed to synthesize electrocatalytic N-doped carbon-based composite materials with solution plasma (SP) using Co or Ni as electrodes from organic solvents containing cup-stacked carbon nanotubes (CSCNTs), iron (II) phthalocyanine (FePc), and N-nethyl-2-pyrrolidinone (NMP). The synthesized N-doped carbon-based composite materials were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). TEM observation and XPS measurements revealed that the synthesized carbon materials contained elemental N, Fe, and electrode-derived Co or Ni, leading to the successful synthesis of N-doped carbon-based composite materials. The electrocatalytic activity for ORR of the synthesized carbon-based composite materials was also evaluated using electrochemical measurements. The electrochemical measurements demonstrated that the electrocatalytic performance for ORR of N-doped carbon-based composite material including Fe and Co showed superiority to that of N-doped carbon-based composite material including Fe and Ni. The difference in the electrocatalytic performance for ORR is discussed regarding the difference in the specific surface area and the presence ratio of chemical bonding species.

Abstract Babesia parasite invades exclusively red blood cell (RBC) in mammalian host and induces alterations to host cell for survival. Despite the importance of Babesia in livestock industry and emerging cases in humans, their basic biology is hampered by lack of suitable biological tools. In this study, we aimed to develop a synchronization method for Babesia bovis which causes the most pathogenic form of bovine babesiosis. Initially, we used compound 2 (C2), a specific inhibitor of cyclic GMP-dependent protein kinase (PKG), and a derivative of C2, ML10. While both inhibitors were able to prevent B. bovis egress from RBC and increased percentage of binary forms, removal of inhibitors from culture did not result in a synchronized egress of parasites. Because using PKG inhibitors alone was not efficient to induce a synchronized culture, we isolated viable and invasive B. bovis merozoites and showed dynamics of merozoite invasion and development in RBCs. Using isolated merozoites we showed that BbVEAP, VESA1-export associated protein, is essential for parasite development in the RBC while has no significant role in invasion. Given the importance of invasion for the establishment of infection, this study paves the way for finding novel antigens to be used in control strategies against bovine babesiosis.

Abstract Theileria equi, an intraerythrocytic protozoan parasite, causes equine piroplasmosis, a disease which negatively impacts the global horse industry. Genetic manipulation is one of the research tools under development as a control method for protozoan parasites, but this technique needs to be established for T. equi. Herein, we report on the first development of a stable transgenic T. equi line expressing enhanced green fluorescent protein/blasticidin S deaminase (eGFP/BSD). To express the exogenous fusion gene in T. equi, regulatory regions of the elongation factor-1 alpha (ef-1α) gene were identified in T. equi. An eGFP/BSD-expression cassette containing the ef-1α gene promoter and terminator regions was constructed and integrated into the T. equi genome. On day 9 post-transfection, blasticidin-resistant T. equi emerged. In the clonal line of T. equi obtained by limiting dilution, integration of the eGFP/BSD-expression cassette was confirmed in the designated B-locus of the ef-1α gene via PCR and Southern blot analyses. Parasitaemia dynamics between the transgenic and parental T. equi lines were comparable in vitro. The eGFP/BSD-expressing transgenic T. equi and the methodology used to generate it offer new opportunities for better understanding of T. equi biology, with the add-on possibility of discovering effective control methods against equine piroplasmosis.

Abstract Cathode materials are essential for enhancing electrocatalytic activity in energy-conversion devices. Carbon is one of the most suitable cathodic materials for Li–O2 batteries owing to its chemical and thermal stability. Carbon materials synthesized from tributyl borate (TBB) using a nonthermal solution plasma method were characterized using x‐ray diffraction, Raman, field emission scanning electron microscopy (FE-SEM), transmission electron microscopy, and x-ray photoelectron spectroscopy and were evaluated as additive materials for cathodes in a Li–O2 battery. Two separate carbon materials were formed at the same time, a carbon dispersed in solution and a carbon precipitate at the bottom of the reactor, which had amorphous and graphite-like structures, respectively. The amorphous carbon contained boron and tungsten carbide, and the graphite-like carbon had more defects and electronic conductivity. The crystallinity and density of defects in the graphite-like carbon could be tuned by changing the SP operating frequency. The Li–O2 battery with the amorphous carbon containing boron and tungsten carbide was found to have a high capacity, while the one with the graphite-like carbon showed an affinity for the formation of Li2O2, which is the desired discharge product, and exhibited high cycling performance.

Li-air batteries have attracted considerable attention as rechargeable secondary batteries with a high theoretical energy density of 11,400 kWh/g. However, the commercial application of Li-air batteries is hindered by issues such as low energy efficiency and a short lifetime (cycle numbers). To overcome these issues, it is important to select appropriate cathode materials that facilitate high battery performance. Carbon materials are expected to be ideal materials for cathodes due to their high electrical conductivity and porosity. The physicochemical properties of carbon materials are known to affect the performance of Li-air batteries because the redox reaction of oxygen, which is an important reaction for determining the performance of Li-air batteries, occurs on the carbon materials. In this study, we evaluated the effect of the surface modification of carbon cathode materials on the charge–discharge performance of Li-air batteries using commercial Ketjenblack (KB) and KB subjected to vacuum ultraviolet (VUV) irradiation as cathodes. The surface wettability of KB changed from hydrophobic to hydrophilic as a result of the VUV irradiation. The ratio of COOH and OH groups on the KB surface increased after VUV irradiation. Raman spectra demonstrated that no structural change in the KB before and after VUV irradiation was observed. The charge and discharge capacities of a Li-air battery using VUV-irradiated KB as the cathode decreased compared to original KB, whereas the cycling performance of the Li-air battery improved considerably. The sizes and shapes of the discharge products formed on the cathodes changed considerably due to the VUV irradiation. The difference in the cycling performance of the Li-air battery was discussed from the viewpoint of the chemical properties of KB and VUV-irradiated KB.

ABSTRACT Erythrocyte-binding-like (EBL) proteins are known to play an important role in malaria parasite invasion of red blood cells (RBCs); however, any roles of EBL proteins in regulating host immune responses remain unknown. Here, we show that Plasmodium yoelii EBL (PyEBL) can shape disease severity by modulating the surface structure of infected RBCs (iRBCs) and host immune responses. We identified an amino acid substitution (a change of C to Y at position 741 [C741Y]) in the protein trafficking domain of PyEBL between isogenic P. yoellii nigeriensis strain N67 and N67C parasites that produce different disease phenotypes in C57BL/6 mice. Exchanges of the C741Y alleles altered parasite growth and host survival accordingly. The C741Y substitution also changed protein processing and trafficking in merozoites and in the cytoplasm of iRBCs, reduced PyEBL binding to band 3, increased phosphatidylserine (PS) surface exposure, and elevated the osmotic fragility of iRBCs, but it did not affect invasion of RBCs in vitro. The modified iRBC surface triggered PS-CD36-mediated phagocytosis of iRBCs, host type I interferon (IFN-I) signaling, and T cell differentiation, leading to improved host survival. This study reveals a previously unknown role of PyEBL in regulating host-pathogen interaction and innate immune responses, which may be explored for developing disease control strategies. IMPORTANCE Malaria is a deadly parasitic disease that continues to afflict hundreds of millions of people every year. Infections with malaria parasites can be asymptomatic, with mild symptoms, or fatal, depending on a delicate balance of host immune responses. Malaria parasites enter host red blood cells (RBCs) through interactions between parasite ligands and host receptors, such as erythrocyte-binding-like (EBL) proteins and host Duffy antigen receptor for chemokines (DARC). Plasmodium yoelii EBL (PyEBL) is known to play a role in parasite invasion of RBCs. Here, we show that PyEBL also affects disease severity through modulation of host immune responses, particularly type I interferon (IFN-I) signaling. This discovery assigns a new function to PyEBL and provides a mechanism for developing disease control strategies.

Fuel cells are expected to serve as next-generation energy conversion devices owing to their high energy density, high power, and long life performance. The oxygen reduction reaction (ORR) is important for determining the performance of fuel cells; therefore, using catalysts to promote the ORR is essential for realizing the practical applications of fuel cells. Herein, we propose Nb-incorporated TiO2 as a suitable alternative to conventional Pt-based catalysts, because Nb doping has been reported to improve the conductivity and electron transfer number of TiO2. In addition, Nb-incorporated TiO2 can induce the electrocatalytic activity for the ORR. In this paper, we report the synthesis method for Nb-incorporated TiO2 through a hydrothermal process with and without additional load pressures. The electrocatalytic activity of the synthesized samples for the ORR was also demonstrated. In this process, the samples obtained under various load pressures exceeding the saturated vapor pressure featured a high content of Nb and crystalline TiNb2O7, resulting in an ellipsoidal morphology. X-ray diffraction results also revealed that, on increasing the Nb doping amounts, the diffraction peak of the anatase TiO2 shifted to a lower angle and the full width at half maximum decreased. This implies that the Ti atom is exchanged with the Nb atom during this process, resulting in a decrease in TiO2 crystallinity. At a doping level of 10%, Nb-incorporated TiO2 exhibited the best electrocatalytic activity in terms of the oxygen reduction current (iORR) and onset potential for the ORR (EORR); this suggests that 10% Nb-doped samples have the potential for enhancing electrocatalytic activity.

A mechanically alloyed austenitic stainless steel (MA304LZ) was produced from pre-alloyed SUS304L powder with a small amount of Zr addition. The yield stress of MA304LZ was more than 3 times larger than that of SUS304L or 316L, while total elongation was reduced to about one third of the conventional steels. Microstructure analysis revealed an average grain size of 0.42 µm in MA304LZ and about 34/30 µm in SUS304L/316 L. In MA304LZ, two types of precipitates were observed; inhomogeneously distributed fine precipitates with an average size of 6.0 nm and homogeneously distributed coarse precipitates (d > 20 nm) with an average size of 47 nm. The strengthening mechanism of MA304LZ was discussed on the bases of Hall-Petch and Orowan equations, and the strengthening of MA304LZ was attributed mostly to refined grains. The dislocation barrier strength factor, α, is estimated to be 0.277 for the Zr-rich precipitates in MA304LZ. Keywords: Powder metallurgy, Grain size effect, Precipitation hardening, Zr-oxides

ABSTRACT Babesia bovis, the most virulent causative agent of bovine babesiosis, is prevalent in tropical and subtropical regions of the world. Although the whole-genome sequence was released more than a decade ago, functional analysis of the genomics of this parasite is hampered by the limited breadth of genetic engineering tools. In this study, we implemented the clustered regularly interspaced short palindromic repeat (CRISPR)/Cas9 system for B. bovis and demonstrated its potential for genome editing. Cas9 and human dihydrofolate reductase (hDHFR) were simultaneously expressed by the B. bovis elongation factor-1α bidirectional promoter, and a single guide RNA was expressed via the B. bovis U6 spliceosomal RNA promoter. Using a single plasmid construct, we were able to add an epitope tag to spherical body protein 3 (SBP3), introduce a point mutation into thioredoxin peroxidase 1 (tpx-1) to impair the function of the product, and replace the tpx-1 open reading frame with the other protein. Epitope tagging of SBP3 was efficient using this system, with a negligible number of remaining wild-type parasites and a pure transgenic population produced by allelic replacement of tpx-1. This advancement in genetic engineering tools for B. bovis will aid functional analysis of the genome and underpin characterization of candidate drug and vaccine targets. IMPORTANCE Babesia bovis is the most virulent cause of bovine babesiosis worldwide. The disease consequences are death, abortion, and economical loss due to reduced milk and meat production. Available vaccines are not effective, treatment options are limited, and emergence of drug and acaricide resistance has been reported from different regions. There is an urgent need to identify new drug and vaccine targets. Greater than half of the genes in B. bovis genome, including several expanded gene families which are unique for Babesia spp., have no predicted function. The available genetic engineering tools are based on conventional homologous recombination, which is time-consuming and inefficient. In this study, we adapted the CRISPR/Cas9 system as a robust genetic engineering tool for B. bovis. This advancement will aid future functional studies of uncharacterized genes.

Metal-air batteries are attracting increasing attention as a superior renewable energy conversion device due to their high performance and strong potential. However, the high cost and low stability of the current Pt catalyst is the main obstacle preventing wide industrial application. In this work, we applied a plasma process to fabricate aniline and a transition metals electrode (Fe, Co, Ni) as the carbon-nitrogen and the metal nanoparticle (NP) precursors, respectively, for selective metal/amino-N-doped carbon catalysts. All three as-synthesized catalysts exhibited dominant amino-N as the major C–N bonding state. In electrochemical testing, Co/amino-N-doped carbon showed positive E1/2 potential (0.83 V vs. Reversible Hydrogen Electrode (RHE)). In addition, the calculated electron transfer number (n) of Co/amino-N-doped carbon at 0.5 V vs. RHE was 3.81, which was only slightly less than that of commercial Pt/C (3.97). This superior performance of transition metal/amino-N-doped carbon promotes it as an economical oxygen reduction reaction (ORR) electrocatalyst to replace expensive Pt/C in metal-air batteries.

Mg alloys are expected to be used in fields of the transportation industry because of their lightweight property, however, they show low corrosion resistance. To improve the corrosion resistance, preparation of the protective film on Mg alloys is essential. In this study, composite hydroxide films were prepared on three types of Mg alloys with different aluminum contents—that is, AZ31, AZ61, and AZ91D—by steam coating to investigate the relationship between the Mg-Al layered double hydroxide (LDH) content in the film and the Al content in the Mg alloys. Scanning electron microscopy (SEM) observation demonstrated that films were formed densely on all Mg alloy surfaces. X-ray diffraction (XRD) analyses revealed that all films prepared on AZ61 and AZ91D were composed of Mg(OH)2, AlOOH, and Mg-Al LDH, while the film containing Mg(OH)2 and Mg-Al LDH were formed only on AZ31. The Mg-Al LDH content in the film prepared on AZ61 was relatively higher than those prepared on AZ31 and AZ91D. The content of AlOOH in the film increased with an increase in the Al content in the Mg alloys. The film thickness changed depending on the treatment time and type of Mg alloy. Polarization curve measurements in 5 mass% NaCl solution demonstrated that the film prepared on the AZ61 showed complete passive behavior within the potential range of −1.0 to −0.64 V. In addition, immersion tests in 5 mass% NaCl aqueous solution for 480 h demonstrated that the film on the AZ61 had superior durability against 5 mass% NaCl aqueous solution. These results indicated that the film on the AZ61 had the most superior corrosion resistance among all samples. The results obtained in this study suggest that the LDH content in the film could be related to the corrosion resistance of the film.

Corrosion resistant films with almost the same film thickness were prepared on the magnesium alloy AZ61 by steam coating at different vapor pressure and treatment times. The effect of the vapor pressure on the structures and the corrosion resistance of the films was investigated by using FE-SEM, SEM-EDX, GAXRD, and potentiodynamic polarization curve measurements in a 3.5 mass percentage NaCl aqueous solution. These studies clarified that the interlayers of Mg-Al Layered Double Hydroxide (LDHs) increased and its structure became non-uniform with an increase in the vapor pressure. The corrosion current density slightly increased with an increase in the vapor pressure during the treatment, but pitting corrosion occurred at both low and high vapor pressures. These results indicate that water molecules were pushed into an interlayer of Mg-Al LDHs by high vapor pressure. Consequently, the interlayer distance of Mg-Al LDH was widened and the cracks were generated in the anti-corrosive film. On the other hand, the Mg-Al LDH with an insufficiently large interlayer distance could not fill the cracks in the Mg(OH)2 crystallites and caused pitting corrosion when the vapor pressure was low.

The ~30 Mb genomes of the Plasmodium parasites that cause malaria each encode ~5000 genes, but the functions of the majority remain unknown. This is due to a paucity of functional annotation from sequence homology, which is compounded by low genetic tractability compared with many model organisms. In recent years technical breakthroughs have made forward and reverse genome-scale screens in Plasmodium possible. Furthermore, the adaptation of Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR) and CRISPR-Associated protein 9 (CRISPR/Cas9) technology has dramatically improved gene editing efficiency at the single gene level. Here, we review the arrival of genetic screens in malaria parasites to analyse parasite gene function at a genome-scale and their impact on understanding parasite biology. CRISPR/Cas9 screens, which have revolutionised human and model organism research, have not yet been implemented in malaria parasites due to the need for more complex CRISPR/Cas9 gene targeting vector libraries. We therefore introduce the reader to CRISPR-based screens in the related apicomplexan Toxoplasma gondii and discuss how these approaches could be adapted to develop CRISPR/Cas9 based genome-scale genetic screens in malaria parasites. Moreover, since more than half of Plasmodium genes are required for normal asexual blood-stage reproduction, and cannot be targeted using knockout methods, we discuss how CRISPR/Cas9 could be used to scale up conditional gene knockdown approaches to systematically assign function to essential genes. [ABSTRACT FROM AUTHOR]

The surface potential reversibility originating from a reversible chemical reaction between amino and nitroso groups is reported. The surface potential memory, which is the nanoprobe electrochemical technique that is based on this chemical reversibility, is demonstrated.

High quality upconverting NaYF4:Ln (Ln = Yb, Er, Tm) crystal layers were successfully fabricated directly onto glass substrates at a relatively low temperature of 350 °C by a novel two-step flux coating method. First, mixed pastes of solute (NaF and YF3) and dopants (LnF3) were coated on glass substrates by simple bar-coating, and then flux pastes (NaNO3or NaNO3–NaF) were coated onto the dopant-containing solute layer. After the two-step coating, raw material-coated substrates were heated at 350 or 400 °C in an electric furnace. To remove the remaining flux, the crystal layers were washed with warm water. Finally, high quality, nanotextured NaYF4:Ln crystal layers with good adhesion were directly grown onto the glass substrates. These crystal layers consisted of densely packed idiomorphic NaYF4:Ln crystals. In particular, individual NaYF4:Ln crystals were typically shaped as hexagonal prisms. The NaYF4:Ln crystal phases depended strongly on the heating conditions, i.e., temperature and time. The NaNO3and NaNO3–NaF fluxes were effective for the growth of high-quality idiomorphic NaYF4:Ln crystals. Additionally, the upconversion fluorescence properties of NaYF4:Ln crystal layers were controlled by changing dopant types and ratios. The NaYF4:10%Yb,1%Er, NaYF4:50%Yb,1%Er, NaYF4:20%Yb,1%Tm and NaYbF4:1%Er crystal layers emitted green, orange, blue and red fluorescences, respectively, under 980 nm laser irradiation. [ABSTRACT FROM AUTHOR]

Alkanoic and phosphonic acid derived self-assembled monolayers (SAMs) were formed on magnesium alloy by the vapor phase method. AFM and XPS studies showed that SAMs were formed on Mg alloy. The chemical and anticorrosive properties of the SAMs prepared on magnesium alloys were characterized using contact angle measurements, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. Water contact angle measurements revealed that, although SA and ISA have the same headgroup to anchor to the magnesium alloy surface, the packing density on the magnesium alloy surface could be considerably different. The contact angle hysteresis of SAMs with a carboxylate headgroup is much larger than that of SAMs with a phosphonic acid group. The XPS O 1s peaks indicated more likely a mix of mono-, bi-, or tridentate binding of phosphonic acid SAM to the oxide or hydroxide surface of the Mg alloy. The electrochemical measurements showed that the phosphonic acid derived SAM had better corrosion resistance compared to alkanoic acid derived SAM. The chemical stability of SAMs modified magnesium alloy was investigated using water contact angle and XPS measurements. The water contact angle and XPS measurements revealed that the molecular density of OP and PFEP on magnesium alloy would be higher than those of SA and ISA on magnesium alloy. [ABSTRACT FROM AUTHOR]

The design of color-tuned magnesium alloy with anticorrosive properties and damping capacity was created by means of a simple and inexpensive method. The vertically self-aligned nano- and microsheets were formed on magnesium alloy AZ31 by a chemical-free immersion process in ultrapure water at a temperature of 120 °C, resulting in the color expression. The color changed from silver with metallic luster to some specific colors such as orange, green, and orchid, depending on the immersion time. The color-tuned magnesium alloy showed anticorrosive performance and damping capacity. In addition, the colored surface with minute surface textures was modified with n-octadecyltrimethoxysilane (ODS), leading to the formation of color-tuned superhydrophobic surfaces. The corrosion resistance of the color-tuned superhydrophobic magnesium alloy was also investigated using electrochemical potentiodynamic measurements. Moreover, the color-tuned superhydrophobic magnesium alloy showed high hydrophobicity not just for pure water but also for corrosive liquids, such as acidic, basic, and some aqueous salt solutions. In addition, the American Society for Testing and Materials (ASTM) standard D 3359-02 cross cut tape test was performed to investigate the adhesion of the color-tuned superhydrophobic film to the magnesium alloy surface. [ABSTRACT FROM AUTHOR]

Highly crystalline, well-developed potassium titanoniobate (KTiNbO5and KTi3NbO9) crystals were successfully grown at temperatures ranging from 700 to 1000 °C by a KCl flux cooling method. Colourless and transparent KTiNbO5crystals with a smallest average size of 750 nm were grown at a relatively low temperature of 700 °C. The sizes of grown crystals were observed to greatly dependent on the holding temperature and solute concentration. HRTEM observations indicated that the flux-grown KTiNbO5crystals were of high quality. The band gap energies of the fabricated KTiNbO5and KTi3NbO9crystals, as estimated from their absorption edges in UV-vis diffuse reflectance spectra, were approximately 3.54 and 3.35 eV, respectively. Furthermore, these crystals exhibited good photocatalytic activities under UV light irradiation. The photodecomposition of TCE gas occurred viaa photocatalytic process under UV light irradiation. This study demonstrates that KCl flux cooling is an environmentally friendly and nature-mimetic process for growing high-quality, well-developed, and photocatalytic KTiNbO5and KTi3NbO9crystals. [ABSTRACT FROM AUTHOR]

We have developed a facile, simple, time-saving method of creating a superhydrophobic surface on a magnesium alloy by a simple immersion process at room temperature. First, a crystalline CeO2film was vertically formed on the magnesium alloy by immersion in a cerium nitrate aqueous solution for 20 min. The density of the crystals vertically with respect to the magnesium alloy increased with increasing immersion time. Next, the film were covered with fluoroalkylsilane (FAS: CF3(CF2)7CH2CH2Si(OCH3)3) molecules within 30 min by immersion in a toluene solution containing FAS and tetrakis(trimethylsiloxy)titanium (TTST: (CH3)3SiO)4Ti). TTST was used as a catalyst to promote the hydrolysis and/or polymerization of FAS molecules. The FAS-coated CeO2film had a static contact angle of more than 150°, that is, a superhydrophobic property. The shortest processing time for the fabrication of the superhydrophobic surface was 40 min. The contact angle hysteresis decreased with an increase in the immersion time in the cerium nitrate aqueous solution. The chemical stability of the superhydrophobic surface on magnesium alloy AZ31 was investigated. The average static water contact angles of the superhydrophobic surfaces after immersion in the solutions at pH 4, 7, and 10 for 24 h were found to be 139.7 ± 2, 140.0 ± 2, and 145.7 ± 2°, respectively. In addition, the chemical stability of the superhydrophobic surface in the solutions at pH ranging from 1 to 14 was also examined. The superhydrophobic surfaces had static contact angles of more than 142° in the solutions at pH ranging from 1 to 14, showing that our superhydrophobic surface had a high chemical stability. Moreover, the corrosion resistance of the superhydrophobic surface on the magnesium alloy was investigated using electrochemical measurements. [ABSTRACT FROM AUTHOR]

A micropatterned superhydrophobic/superhydrophilic surface was successfully fabricated by plasma CVD and VUV irradiation. Physicochemical properties of the superhydrophobic, superhydrophilic, and superhydrophobic/superhydrophilic surfaces were investigated. The roughness structures on the superhydrophilic surface remained intact compared to those of the superhydrophobic surface. The micropatterned superhydrophobic/superhydrophilic surface was used as a scaffold of cell culture. On the micropatterned surface, the cells attached to the superhydrophilic regions in a highly selective manner, forming circular microarrays of the cells corresponding to the pattern. On the micropatterned surface with pattern distances of 200 μm between superhydrophilic regions, the cells adhered on the superhydrophilic regions and partly extended to the neighboring cells. In contrast, when the pattern distances between the superhydrophilic regions were more than 400 μm, the cells did not extend to the neighboring cells. Cell adhesion behaviors on superhydrophobic and superhydrophilic surfaces were also examined. The cells adhered and proliferated on both superhydrophobic and superhydrophilic surfaces. However, on the superhydrophobic surface, constant contact to facilitate cell division and proliferation was required. On the other hand, the cells easily adhered and proliferated on the superhydrophilic surface immediately after seeding. These differences in cell adhesion behavior induced site-selective cell adhesion on the superhydrophilic regions. Furthermore, protein adsorption behavior that plays an important role in cell adhesion on flat hydrophobic and hydrophilic surface was also examined. The amounts of the protein adsorption on the flat hydrophilic surface were much greater than those on the flat hydrophobic surface. [ABSTRACT FROM AUTHOR]

Crystalline nanosheets were successfully formed on magnesium alloy AZ31 by a facile surfactant-free hydrothermal treatment using aqueous solution. The crystal structures and shapes of the nanosheets changed with the treatment temperature. On treatment at 120 °C, rosette-like structures made from curved nanosheets of crystalline Mg1−xAlx(OH)2(NO3)x·nH2O were formed. At 150 °C, plate-like nanosheets of crystalline Mg1−xAlx(OH)2(NO3)x·nH2O and Mg(OH)2were formed. Further increase in the treatment temperature to 180 °C yielded larger crystals with sharp edges. The crystallites were crystalline Mg(OH)2with a distinct plate-like shape with the edges preferentially directed out of the magnesium alloy. The formation mechanism of this morphology is also discussed. [ABSTRACT FROM AUTHOR]

Ultra-water-repellent (UWR) films were prepared by microwave plasma-enhanced chemical vapour deposition using trimethylmethoxysilane and aluminium (III) diisopropoxide ethylacetoacetate (ADE) as raw materials. The film was mainly composed of silica and alumina and was apparently transparent. The film thickness was approximately 500?nm. The sample surface was treated with an organosilane in order to introduce hydrophobic groups. The hydrophobic modification led to a water contact angle of more than 150°, whose value corresponds to the UWR surface. The hardness of film with an optimized Al content was significantly improved compared with that without Al. The maximum hardness was 1.71?GPa. In consequence, we successfully prepared an UWR film in the silica-alumina system. [ABSTRACT FROM AUTHOR]

Idiomorphic and one-dimensional (1-D) Ca5F(PO4)3(fluorapatite, FAp) crystals were successfully, directly, and densely grown on silicon and poly(ethylene terephthalate) (PET) substrates viaan atmospheric pressure plasma-assisted flux coating (APP-FC) method. To achieve a low-temperature crystal growth, a KNO3–LiNO3mixture was chosen as the flux. [ABSTRACT FROM AUTHOR]

Carbon-based materials have been widely utilized as the electrode materials in energy conversion and storage technologies, such as fuel cells and metal–air batteries. In these systems, the oxygen reduction reaction is an important step that determines the overall performance. A novel synthesis route, named the solution plasma process, has been recently utilized to synthesize various types of metal-based and heteroatom-doped carbon catalysts. In this review, we summarize cutting-edge technologies involving the synthesis and modeling of carbon-supported catalysts synthesized via solution plasma process, followed by current progress on the electrocatalytic performance of these catalysts. This review provides the fundamental and state-of-the-art performance of solution-plasma-synthesized electrode materials, as well as the remaining scientific and technological challenges for this process. [ABSTRACT FROM AUTHOR]

For several decades, the development of synthesis processes and designs for carbon materials such as graphites, carbon nanotubes, and graphenes has been continuous because of their superior physicochemical properties. The liquid-phase electric discharge process, known as the solution plasma process (SPP), has emerged as a potential synthesis process for carbon materials; however, liquid discharge in organic solutions has not yet been thoroughly investigated. In this study, plasma discharges in benzene (C6H6) and pyridine (C5H5N) were conducted. During the discharge, two types of nanocarbons with different crystallinities were synthesized simultaneously in different reaction fields: between electrodes and in a liquid phase. The nanocarbons grown between electrodes were collected and then compared with the nanocarbons produced in the liquid phase after discharge. All carbon samples were measured using various techniques such as transmission electron microscopy (TEM), the nitrogen absorption–desorption method, X-ray diffraction (XRD), Raman spectroscopy, CHN elemental analysis, and X-ray photoelectron spectroscopy (XPS). Nanocarbons grown between electrodes in benzene or pyridine were found to be graphite structures, while the nanocarbons produced in the liquid phase were amorphous carbons. On the basis of the results obtained, the formation and growth of the two types of nanocarbon materials synthesized by SPP and their dependence on the position of the reaction field in plasma in the liquid phase are discussed. [ABSTRACT FROM AUTHOR]

Nanocarbons were synthesized by a solution plasma method using benzene (C6H6) and benzotrifluoride (C5H5CF3) as precursors. The effects of the substituted CF3 group on the overall properties of synthesized nanocarbons were investigated and discussed. As determined from the characterization results, the nanocarbons obtained from both benzene and benzotrifluoride mainly exhibited an amorphous structure and their diameter was about 20–40 nm. There were no notable differences in morphology, surface area, and crystalline structure observed between them. Interestingly, the synthesis rate of nanocarbons from benzotrifluoride (20.3 mg/min) was almost three fold higher than that from benzene (7.6 mg/min). Moreover, a lower H/C ratio was observed in the case of nanocarbons from benzotrifluoride, indicating its more efficient H abstraction. The higher synthesis rate and lower H/C ratio of nanocarbons from benzotrifluoride were possibly attributed to the CF3 radicals generated in the reaction fields of solution plasma during synthesis. [ABSTRACT FROM AUTHOR]