Search

High dielectric constant ceramics fillers are widely used as fillers in polymer matrix to prepare high performance dielectric composites. Homogeneous filler distribution in these composites films is found to be quite difficult to achieve balance between high dielectric constant and high breakdown strength. Herein, multilayer structured composites films containing nickelous hydroxide (Ni(OH)2) as fillers, with different multilayered structures were designed and prepared, including 2–5 layers structure with various filler distribution. The effects of multilayer structure on the dielectric performance are explored by keeping the overall filler content constant. Combined with computer simulation, it is suggested that the variation in filler distribution in these films can effectively redistribute electric field intensity. Meanwhile, the dielectric constant and breakdown strength of the overall composites can be adjusted by changing the volume ratio between high filler content layer and low filler content layer. It is noted that at least 1/3 of the overall film volume should be occupied by a high breakdown strength layer to keep rather high overall breakdown strength. Moreover, high dielectric constant layer should be the outer layers to achieve overall high dielectric constant. Among all the layered structures investigated, the maximum energy density of 6.03 J/cm3 is obtained for film with a 3-layer nonsequential arrangement structure, which is 68% higher than single layer film with identical composition. This study provides some reference value for the preparation of multilayered dielectric polymer composites films for energy storage applications.

In this study, highly oriented shish-kebab structure was achieved via imposing oscillatory shear on the melts of linear low density polyethylene (LLDPE)/high density polyethylene (HDPE) blends during the packing stage of injection molding. To investigate the effect of molecular weight of HDPE on the formation of shish-kebab structure, two kinds HDPE with large melt flow index (low molecular weight) and small melt flow index (high molecular weight) were added into LLDPE matrix. The structural characteristics of LLDPE/HDPE blends were systematically elucidated through two-dimensional wide-angle x-ray scattering, scanning electron microscopy, and differential scanning calorimetry. Interestingly, an unexpected molecular weight dependence of shish-kebab structure of the prepared samples was found that the addition of HDPE with low molecular weight resulted in an higher degree of orientation, better regularity of lamellar arrangement, thicker lamellar size, and higher crystal melting temperature than that adding HDPE with high molecular weight. Correspondingly, the blend containing low molecular weight HDPE had better tensile strength. A possible mechanism was suggested to elucidate the role of HDPE molecular weight on the formation of shish-kebab structure in the oriented blends, considering the change of chain mobility and entanglement density with change of molecular weight. [ABSTRACT FROM AUTHOR]

In this article, the phase morphology and mechanical properties of polypropylene (PP)/ethylene–octane copolymer (POE) blends with fixed ratio (60/40) obtained via different processing conditions, including barrel temperature, injection speed, and mold temperature, have been investigated. SEM was carried out for detailed characterization of phase morphology from the skin to the core, layer by layer. It was interesting that for all the processing conditions no dispersed POE elastomer was observed in the skin layer but elongated POE particles with large size were observed in the subskin layer. From the transition zone to the core layer, an increased phase separation was observed, which could lead to a formation of cocontinuous morphology, depending on the processing condition used. Higher barrel temperature, lower mold temperature, and higher injection speed could result in a smaller size of POE phase. The tensile strength and impact strength were found not sensitive to barrel temperature and mold temperature but to the low injection speed, both tensile strength and impact strength had a higher value for specimen obtained via low injection speed. The formation of the skin‐core morphology and the effect of processing conditions on the phase morphology were discussed based on crystallization kinetics of PP matrix, rheology, and shear induced phase mixing. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007 [ABSTRACT FROM AUTHOR]

In this article, polypropylene (PP)/multiwall carbon nanotubes (MWNTs) composites were prepared through dynamic packing injection molding, in which the oscillatory shear was exerted on the molten composite during packing and solidification stage of injection‐molding. A simultaneous increase of tensile strength and impact strength has been achieved for PP/MWNTs composites containing only 0.6 wt % MWNTs. Particularly, the impact strength was found increased by almost 50% at such low MWNTs content. These improvements in properties were attributed to uniform dispersion and possible orientation of nanotube induced by shear stress. It was suggested that the dynamic packing injection molding could provide much strong shear force for better dispersion of MWNTs in PP matrix, on one hand, but breakdown the aspect ratio of MWNTs, on the other. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1880–1886, 2007 [ABSTRACT FROM AUTHOR]