Search

This study aimed to characterize biofilms from the paper industry and evaluate the effectiveness of enzymatic treatments in reducing them. The extracellular polymeric substances (EPS) extracted from six industrial biofilms were studied. EPS were mainly proteins, the protein to polysaccharide ratio ranging from 1.3 to 8.6 depending on where the sampling point was situated in the paper making process. Eight hydrolytic enzymes were screened on a 24-h multi-species biofilm. The enzymes were tested at various concentrations and contact durations. Glycosidases and lipases were inefficient or only slightly efficient for biofilm reduction, while proteases were more efficient: after treatment for 24 h with pepsin, Alcalase® or Savinase®, the removal exceeded 80%. Savinase® appeared to be the most adequate for industrial conditions and was tested on an industrial biofilm sample. This enzyme led to a significant release of proteins from the EPS matrix, indicating its potential efficiency on an industrial scale. [ABSTRACT FROM PUBLISHER]

The use of electrocoagulation (EC) and anodic oxidation (AO) processes was studied for improving a treatment system for landfill leachates based on a membrane bioreactor (MBR) and a nanofiltration step. The main limitation of the current full-scale system is related to the partial removal of organic compounds that leads to operation of the nanofiltration unit with a highly concentrated feed solution. Application of the EC before the MBR participated in partial removal of the organic load (40 %) with limited energy consumption (2.8 kWh m -3 ) but with additional production of iron hydroxide sludge. Only AO allowed for non-selective removal of organic compounds. As a standalone process, AO would require a sharp increase of the energy consumption (116 kWh for 81 % removal of total organic carbon). But using lower electric charge and combining AO with EC and MBR processes would allow for achieving high overall removal yields with limited energy consumption. For example, the overall removal yield of total organic carbon was 65 % by application of AO after EC, with an energy consumption of 21 kWh m -3 . Results also showed that such treatment strategy might allow for a significant increase of the biodegradability of the effluent before treatment by the MBR. The MBR might then be dedicated to the removal of the residual organic load as well as to the removal of the nitrogen load. The data obtained in this study also showed that the lower electric charge required for integrating AO in a coupled process would allow for strongly decreasing the formation of undesired by-products such as ClO 3 - and ClO 4 - ., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Volatilization of hazardous hydrophobic organic compounds is often observed in many water, wastewater and soil treatment (bio)processes. Several models have been developed to quantify and predict gas-liquid pollutant transfer, being the proportionality coefficient model (PCM) one of the most commonly used, particularly in wastewater treatment. The PCM is based on the use of oxygen as a reference compound, which has a low resistance to the transfer in the gas phase. However, this resistance might be important for (semi-)volatile organic compounds - or (semi-)VOCs, which may render the use of the PCM model inaccurate. This study proposes an experimental methodology and a modeling approach for the use of the two-reference compound model (2RCM) that considers both the liquid-side and the gas-side resistances, by using water and oxygen as references. Results showed that the 2RCM predicts more accurately the overall mass transfer coefficients than the PCM for a VOC and two semi-VOCs tested in this study. In addition, the 2RCM was found to be a more robust method to estimate mass transfer coefficient of any compound and its use can be extrapolated to all substances. Finally, the relevance and limitations of both models was established., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Sewage sludge digestate is a valuable organic waste which can be used as fertilizer in soil bioremediation. Sewage sludge digestate is not only a good source of nutrients but is also rich in bacteria carrying alkB genes, which are involved in aliphatic hydrocarbons metabolism. Increase of alkB genes ratio in polluted soils has been observed to improve bioremediation efficiency. In this study, for the first time, the genetic potential of indigenous microorganisms of digestate to degrade petroleum products was assessed. The objectives were to study petroleum hydrocarbons (PHCs) removal together with shifts in soil taxa and changes in the concentration of alkB genes after digestate application. Initial alkB genes concentration in contaminated soils and digestate was 1.5% and 4.5%, respectively. During soil incubation with digestate, alkB genes percentage increased up to 11.5% and after the addition of bacteria immobilized onto biochar this value increased up to 60%. Application of digestate positively affected soil respiration and bacterial density, which was concomitant with enhanced PHCs degradation. Incubation of soil amended with digestate resulted in 74% PHCs decrease in 2 months, while extra addition of bacteria immobilized onto biochar increased this value up to 95%. The use of digestate affected the microbial community profiles by increasing initial bacterial density and diversity, including taxa containing recognized PHCs degraders. This study reveals the great potential of digestate as a soil amendment which additionally improves the abundance of alkB genes in petroleum contaminated soils., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

A lot of soil (particularly, former industrial and military sites) has been contaminated by various highly toxic contaminants such as petroleum hydrocarbons, polycyclic aromatic hydrocarbons (PAHs), polychlorobiphenyls (PCBs) or chlorinated solvents. Soil remediation is now required for their promotion into new industrial or real estate activities. Therefore, the soil washing (SW) process enhanced by the use of extracting agents (EAs) such as surfactants or cyclodextrins (CDs) has been developed for the removal of hydrophobic organic compounds (HOCs) from contaminated soils. The use of extracting agents allows improving the transfer of HOCs from the soil-sorbed fraction to the washing solution. However, using large amount of extracting agents is also a critical drawback for cost-effectiveness of the SW process. The aim of this review is to examine how extracting agents might be recovered from SW solutions for reuse. Various separation processes are able to recover large amounts of extracting agents according to the physicochemical characteristics of target pollutants and extracting agents. However, an additional treatment step is required for the degradation of recovered pollutants. SW solutions may also undergo degradation processes such as advanced oxidation processes (AOPs) with in situ production of oxidants. Partial recovery of extracting agents can be achieved according to operating conditions and reaction kinetics between organic compounds and oxidant species. The suitability of each process is discussed according to the various physicochemical characteristics of SW solutions. A particular attention is paid to the anodic oxidation process, which allows either a selective degradation of the target pollutants or a complete removal of the organic load depending on the operating conditions., (Copyright © 2020 Elsevier B.V. All rights reserved.)

The recovery of iron and other heavy metals by the formation of Fe(III) (hydr)oxides is an important application of microbially-driven processes. The mineral characterization of the precipitates formed during Fe(II)-mediated autotrophic denitrification with and without the addition of Cu, Ni, and Zn by four different microbial cultures was investigated by X-ray fluorescence (XRF), Raman spectroscopy, scanning electron microscopy equipped with energy dispersive X-Ray analyzer (SEM-EDX), Fourier transform infrared spectroscopy (FTIR) and X-ray Powder Diffraction (XRD) analyses. Fe(II)-mediated autotrophic denitrification resulted in the formation of a mixture of Fe(III) (hydr)oxides composed of amorphous phase, poorly crystalline (ferrihydrite) and crystalline phases (hematite, akaganeite and maghemite). The use of a Thiobacillus-dominated mixed culture enhanced the formation of akaganeite, while activated sludge enrichment and the two pure cultures of T. denitrificans and Pseudogulbenkiania strain 2002 mainly resulted in the formation of maghemite. The addition of Cu, Ni and Zn led to similar Fe(III) (hydr)oxides precipitates, probably due to the low metal concentrations. However, supplementing Ni and Zn slightly stimulated the formation of maghemite. A thermal post-treatment performed at 650 °C enhanced the crystallinity of the precipitates and favored the formation of hematite and some other crystalline forms of Fe associated with P, Na and Ca., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Digestate is an organic by-product of biogas production via anaerobic digestion processes and has a great potential as soil fertilizer due to concentrated nutrients. In this study, we examined digestate as a potential nutrient and microbial seeding for bioremediation of weathered (aged) petroleum hydrocarbon contaminated soils. We analysed 6 different treatments in microcosm using two industrial soils having different textures: a clay rich soil and a sandy soil. After 30 days of incubation, the highest total petroleum hydrocarbons (TPH) removal was observed in microcosms containing digestate together with bulking agent (17.8% and 12.7% higher than control in clay rich soil and sandy soil, respectively) or digestate together with immobilized bacteria (13.4% and 9% higher than control in clay rich soil and sandy soil, respectively). After digestate application microbial respiration was enhanced in sandy soil and inhibited in clay rich soil due to aggregates formation. After bulking agent addition to clay rich soil aggregates size was reduced and oxygen uptake was improved. Application of digestate to soil resulted in the development of distinct microbial groups in amended and non-amended soils. Genera containing species able to degrade TPH like Acinetobacter and Mycobacterium were abundant in digestate and in soil amended with digestate. Quantification of alkB genes, encoding alkane monoxygenase, revealed high concentration of these genes in digestate bacterial community. After application of digestate, the level of alkB genes significantly increased in soils and remained high until the end of the treatment. The study revealed great potential of digestate as a nutrient and bacteria source for soil bioremediation., (Copyright © 2019. Published by Elsevier B.V.)

The main objectives of this work are to investigate the consequences of different chemical treatments (i.e. potassium hydroxide (KOH) and hydrogen peroxide (H 2 O 2 )) and the effect of biochar washing on the Pb sorption capacity. Biochars derived from sewage sludge digestate and the organic fraction of municipal solid waste digestate were separately modified with 2 M KOH or 10% H 2 O 2 followed by semi-continuous or continuous washing with ultrapure water using batch or a column reactor, respectively. The results showed that the Pb adsorption capacity could be enhanced by chemical treatment of sludge-based biochar. Indeed, for municipal solid waste biochar, the Pb maximum sorption capacity was improved from 73 mg g -1 for unmodified biochar to 90 mg g -1 and 106 mg g -1 after H 2 O 2 and KOH treatment, respectively. In the case of sewage sludge biochar, it increased from 6.5 mg g -1 (unmodified biochar) to 25 mg g -1 for H 2 O 2 treatment. The sorption capacity was not determined after KOH treatment, since the Langmuir model did not fit the experimental data. The study also highlights that insufficient washing after KOH treatment can strongly hinder Pb sorption due to the release of organic matter from the modified biochar. This organic matter may interact in solution with Pb, resulting in an inhibition of its sorption onto the biochar surface. Continuous column-washing of modified biochars was able to correct this issue, highlighting the importance of implementing a proper treated biochar washing procedure., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

An electro-Fenton (EF) based technology using activated carbon (AC) fiber as cathode and BDD as anode has been investigated for both regeneration of AC and mineralization of organic pollutants. The large specific surface area and low intraparticle diffusion resistance of AC tissue resulted in high maximum adsorption capacity of phenol (PH) (3.7 mmol g -1 ) and fast adsorption kinetics. Spent AC tissue was subsequently used as the cathode during the EF process. After 6 h of treatment at 300 mA, 70% of PH was removed from the AC surface. The effectiveness of the process is ascribed to (i) direct oxidation of adsorbed PH by generated hydroxyl radicals, (ii) continuous shift of adsorption equilibrium due to oxidation of organic compounds in the bulk, and (iii) local pH change leading to electrostatic repulsive interactions. Moreover, 91% of PH removed from AC was completely mineralized, thus avoiding adsorption of degradation byproducts and accumulation of toxic compounds such as benzoquinone. Morphological and chemical characteristics of AC were not affected due to the effect of cathodic polarization protection. AC tissue was successfully reused during 10 cycles of adsorption/regeneration with regeneration efficiency ranging from 65 to 78%, in accordance with the amount of PH removed from the AC surface.

Hydrophobic organic compound (HOC)-contaminated soils are a great environmental and public health concern nowadays. Further research is necessary to develop environmental friendly biotechnologies that allows public and private sectors to implement efficient and adaptable treatment approaches. Aerobic soil-slurry bioreactor technology has emerged as an effective and feasible technique with a high remediation potential, especially for silt and clay soil fractions, which often contain the highest pollutant concentration levels and are usually difficult to remove by implementing conventional methods. However, the mechanisms involved in the HOC removal in bioslurry reactor are still not completely understood. Gas-liquid and solid-liquid mass transfer, mass transport and biodegradation phenomena are the main known processes taking place in slurry bioreactors. This review compiles the most up-to-date information available about these phenomena and tries to link them, enlightening the possible interactions between parameters. It gathers the basic information needed to understand the complex bioremediation technology and raises awareness of some considerations that should be made., (Copyright © 2017. Published by Elsevier B.V.)

Formation of micelles at high surfactant concentration strongly modifies organic pollutant oxidation mechanisms and kinetics during anodic oxidation (AO) using boron doped diamond (BDD) anode. Results presented and discussed in this study emphasized the following mechanisms: (i) micelles act as a protective environment and reduce the availability of target molecules towards BDD( • OH); (ii) the use of low current density strongly reduces micelle degradation kinetics due to both steric hindrance phenomenon for oxidation of micelles at the BDD surface and decrease of mediated oxidation in the bulk; (iii) compounds solubilized in surfactant-containing solutions can be either oxidized after degradation of the protective environment formed by micelles or if they are present as free extra-micellar compounds. Therefore, selective degradation of organic compounds entrapped in micelles can be achieved by using low current density and high surfactant concentration. In fact, these operating conditions strongly hinder micelle oxidation, while free (extra-micellar) compounds can still be oxidized. Then, the remaining entrapped compounds can also be continuously released in the aqueous phase, according to the micellar/aqueous phase partitioning coefficient (K m ). These results have been applied for the treatment of a real polycyclic aromatic hydrocarbon-containing soil washing (SW) solution. After 23 h of treatment at 2.1 mA cm -2 , 83% of phenanthrene, 90% of anthracene, 77% of pyrene and 75% of fluoranthene were degraded and the treated SW solution was reused for an additional SW step with only 5% lower extraction capacity than a fresh TW80 solution. A comparative study highlighted the superiority of this treatment strategy, compared to the use of activated carbon for selective adsorption of polycyclic aromatic hydrocarbons and SW solution reuse., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

The hydrophobic fractionation of extracellular polymeric substances (EPS) extracted from anaerobic granular sludge was performed on the DAX-8 resin (two elution pH conditions, i.e., pH 2 and pH 5 were tested). The impact of seven different EPS extraction methods on EPS hydrophobicity features was assessed. The results showed that the extraction methods and bulk solution pH influenced dramatically the biochemical composition of the EPS, and in turn, the hydrophobicity determined. Besides, EPS extracting reagents i.e., formaldehyde, ethanol, sodium dodecyl sulfate (SDS), and Tween 20 not only introduced extra carbon content in the total organic carbon (TOC) measurement but also interacted with the DAX-8 resin. By comparing the apparent molecular weight (aMW) distribution of untreated and pH-adjusted EPS samples, more complete EPS aMW information was preserved at pH 5. Thus, elution at pH 5 was preferred in this study for the qualitative analysis of EPS hydrophobic features. The hydrophobic fraction of EPS retained by the resin at pH 5 was ascribed to a wide aMW range, ranging from >440 to 0.3 kDa. Within this range, EPS molecules ranging from 175 to 31 kDa were mostly retained by the DAX-8 resin, which indicates that these EPS molecules are highly hydrophobic.

The temporal and spatial effects of selenite (SeO3(2-)) on the physical properties and respiratory activity of Phanerochaete chrysosporium biofilms, grown in flow-cell reactors, were investigated using oxygen microsensors and confocal laser scanning microscopy (CLSM) imaging. Exposure of the biofilm to a SeO3(2-) load of 1.67mgSeL(-1)h(-1) (10mgSeL(-1) influent concentration), for 24h, resulted in a 20% reduction of the O2 flux, followed by a ∼10% decrease in the glucose consumption rate. Long-term exposure (4days) to SeO3(2-) influenced the architecture of the biofilm by creating a more compact and dense hyphal arrangement resulting in a decrease of biofilm thickness compared to fungal biofilms grown without SeO3(2-). To the best of our knowledge, this is the first time that the effect of SeO3(2-) on the aerobic respiratory activity on fungal biofilms is described., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

The release of hydrophobic organoxenobiotics such as polycyclic aromatic hydrocarbons, petroleum hydrocarbons or polychlorobiphenyls results in long-term contamination of soils and groundwaters. This constitutes a common concern as these compounds have high potential toxicological impact. Therefore, the development of cost-effective processes with high pollutant removal efficiency is a major challenge for researchers and soil remediation companies. Soil washing (SW) and soil flushing (SF) processes enhanced by the use of extracting agents (surfactants, biosurfactants, cyclodextrins etc.) are conceivable and efficient approaches. However, this generates high strength effluents containing large amount of extracting agent. For the treatment of these SW/SF solutions, the goal is to remove target pollutants and to recover extracting agents for further SW/SF steps. Heterogeneous photocatalysis, technologies based on Fenton reaction chemistry (including homogeneous photocatalysis such as photo-Fenton), ozonation, electrochemical processes and biological treatments have been investigated. Main advantages and drawbacks as well as target pollutant removal mechanisms are reviewed and compared. Promising integrated treatments, particularly the use of a selective adsorption step of target pollutants and the combination of advanced oxidation processes with biological treatments, are also discussed., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Detachment is one of the major processes determining the physical structure and microbial functionalities of biofilms. To predict detachment, it is necessary to take the mechanical properties of the biofilm and the effect of both hydrodynamic and growth conditions into account. In this work, experiments were conducted with biofilms developed under various shear stresses and with various substrate natures. In addition, two cases were considered in order to differentiate between the effect of hydrodynamic factors and growth factors: the biofilms were directly grown under the targeted shear stress (τ) condition or they were precultivated under very low shear stress (0.01 Pa) and then exposed to high shear stress in the range of 0.1-13 Pa. An exponential and asymptotic decrease of the biofilm thickness and mass with increasing τ was observed in both cases. On contrary density, expressed as the biofilm dry mass on a known substratum divided by the average thickness increased with τ. Denitrifying biofilms always showed greater thickness and density than oxic biofilms. These results showed the presence of a compact basal layer that resisted shear stresses as high as 13 Pa whatever the culture conditions. Above this basal layer, the cohesion was lower and depended on the shear stress applied during biofilm development. The application of shear stress to the biofilms resulted in both detachment and compression, but detachment prevailed for the upper part of the biofilms and compression prevailed for the basal layers. A model of biofilm structure underlying the stratified character of this aggregate is given in terms of density and cohesion., (Copyright © 2012 Elsevier Ltd. All rights reserved.)