Search

The purpose of the study was to compare measured air and surface concentrations after application of biocidal spray products with concentrations simulated with the ConsExpo Web spray simulation tool. Three different biocidal spray products were applied in a 20 m3 climate test chamber with well-controlled environmental conditions (22 ± 1 °C, 50 ± 2% relative humidity, and air exchange rate of 0.5 h−1). The products included an insect spray in a pressurized spray can, another insect spray product, and a disinfectant, the latter two applied separately with the same pumped spray device. The measurements included released particles, airborne organic compounds in both gas and particle phase, and surface concentrations of organic compounds on the wall and floor in front of the spraying position and on the most remote wall. Spraying time was a few seconds and the air concentrations were measured by sampling on adsorbent tubes at 9–13 times points during 4 hr after spraying. The full chamber experiment was repeated 2–3 times for each product. Due to sedimentation the concentrations of the particles in air decayed faster than explained by the air exchange rate. In spite of that, the non-volatile benzalkonium chlorides in the disinfectant could be measured in the air more than 30 min after spraying. ConsExpo Web simulated concentrations that were about half of the measured concentrations of the active substances when as many as possible of the default simulation parameters were replaced by the experimental values. ConsExpo Web was unable to simulate the observed faster decay of the airborne concentrations of the active substances, which might be due to underestimation of the gravitational particle deposition rates. There was a relatively good agreement between measured surface concentrations on the floor and calculated values based on the dislodgeable amount given in the selected ConsExpo Web scenarios. It is suggested to always supplement simulation tool results with practical measurements when assessing the exposure to a spray product. [ABSTRACT FROM AUTHOR]

Private consumers and professionals may experience acute inhalation toxicity after inhaling aerosolized impregnation products. The distinction between toxic and non-toxic products is difficult to make for producers and product users alike, as there is no clearly described relationship between the chemical composition of the products and induction of toxicity. The currently accepted method for determination of acute inhalation toxicity is based on experiments on animals; it is time-consuming, expensive and causes stress for the animals. Impregnation products are present on the market in large numbers and amounts and exhibit great variety. Therefore, an alternative method to screen for acute inhalation toxicity is needed. The aim of our study was to determine if inhibition of lung surfactant by impregnation products in vitro could accurately predict toxicity in vivo in mice. We tested 21 impregnation products using the constant flow through set-up of the constrained drop surfactometer to determine if the products inhibited surfactant function or not. The same products were tested in a mouse inhalation bioassay to determine their toxicity in vivo. The sensitivity was 100%, i.e., the in vitro method predicted all the products that were toxic for mice to inhale. The specificity of the in vitro test was 63%, i.e., the in vitro method found three false positives in the 21 tested products. Six of the products had been involved in accidental human inhalation where they caused acute inhalation toxicity. All of these six products inhibited lung surfactant function in vitro and were toxic to mice. [ABSTRACT FROM AUTHOR]

Background: In most reported cases of lung trauma with water proofing products, volatile organic compounds (VOC) have a prominent role. Here we report on a case involving ten workers exposed to a sprayed product containing nanoparticles in a water solution with only a few percent VOC. Case presentation: Ten workers suffered from respiratory symptoms following spray impregnation of hardwood furniture using a waterproofing product that contained positively charged fluorinated acrylate copolymer solid cores with a median diameter of 70 nm (1.3 w%) in aqueous suspension with 3.3 w% VOC and 0.3 w% quaternary ammonium. The worker who applied one liter of the product in a wood workshop, using an air mix spray gun, did not report any health complaints. Another worker, who entered the workshop 3 h later and had rolled and smoked two cigarettes, was hospitalized with severe chemical pneumonitis. A chest X-ray (CXR) showed bilateral infiltrative impairment in the lower lobe regions. On the next day a second CXR showed increased patchiness marking in all fields. A high-resolution Computer Tomography (CT)-scan demonstrated extensive bilateral areas of ground-glass opacities predominantly in the lower regions of the upper lobes, the right middle lobe and the apical regions of the lower lobes, compatible with severe chemical pneumonitis. On the following morning, nine workers in an adjacent workplace in the same building, experienced dry cough, chest tightness and substernal pain upon physical exercise. Reconstruction of the spray application in a climate chamber confirmed trimethyl silanol, glycol ethers and fluoroalkenes in the gas phase. Immediately after the spray application, aerosols were observed at a maximum concentration of 6.3 x 104 cm-3. Mass concentrations were 0.095 and 10 mg/m³ in the size ranges 5.6-560 nm and 0.22-30 μm, respectively, decreasing to less than 10 µg/m³ in both size ranges after 15 h. Conclusion: The hospitalized worker had smoked cigarettes contaminated with fluoropolymers which is a plausible explanation for the lung trauma. Respiratory symptoms in the nine workers may be caused by inhalation of particles that became airborne by resuspension from surfaces when workers entered the adjacent workplace the next day. A contribution from VOC appears less likely because measurements and modelling showed that concentrations in the mg/m³ range could have occurred only if the building was assumed to be completely airtight. [ABSTRACT FROM AUTHOR]

Inhalation of indoor air pollutants may cause airway irritation and inflammation and is suspected to worsen allergic reactions. Inflammation may be due to mucosal damage, upper (sensory) and lower (pulmonary) airway irritation due to activation of the trigeminal and vagal nerves, respectively, and to neurogenic inflammation. The terpene,d-limonene, is used as a fragrance in numerous consumer products. When limonene reacts with the pulmonary irritant ozone, a complex mixture of gas and particle phase products is formed, which causes sensory irritation. This study investigated whether limonene, ozone or the reaction mixture can exacerbate allergic lung inflammation and whether airway irritation is enhanced in allergic BALB/cJ mice. Naïve and allergic (ovalbumin sensitized) mice were exposed via inhalation for three consecutive days to clean air, ozone, limonene or an ozone–limonene reaction mixture. Sensory and pulmonary irritation was investigated in addition to ovalbumin-specific antibodies, inflammatory cells, total protein and surfactant protein D in bronchoalveolar lavage fluid and hemeoxygenase-1 and cytokines in lung tissue. Overall, airway allergy was not exacerbated by any of the exposures. In contrast, it was found that limonene and the ozone–limonene reaction mixture reduced allergic inflammation possibly due to antioxidant properties. Ozone induced sensory irritation in both naïve and allergic mice. However, allergic but not naïve mice were protected from pulmonary irritation induced by ozone. This study showed that irritation responses might be modulated by airway allergy. However, aggravation of allergic symptoms was observed by neither exposure to ozone nor exposure to ozone-initiated limonene reaction products. In contrast, anti-inflammatory properties of the tested limonene-containing pollutants might attenuate airway allergy. [ABSTRACT FROM PUBLISHER]

RATIONALE: Inhaled nanoparticles may cause adverse effects due to inactivation of lung surfactants. We have studied how three different nanoparticles interact with dipalmitoyl-phosphatidylcholine (DPPC), the main component in lung surfactant. METHODS: DPPC in solution was mixed with a suspension of nanoparticles, both in organic solvent, and allowed to interact for 40 min under conditions partly resembling the alveolar lining. Nanoparticles were isolated by centrifugation, washed, and re-suspended in ethanol/water 1:1 (v/v). The resulting solution was analyzed by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS) using dihydroxybenzoic acid as matrix. RESULTS: The developed methodology was successfully applied for quantitative detection of phospholipid lung surfactant bound to three different types of nanoparticles. Titanium dioxide nanoparticles had a strong affinity for binding of lipid lung surfactant in contrast to pristine and methylated silica nanoparticles. When the concentration of lipid surfactant was raised in the reaction mixture, the titanium dioxide nanoparticles showed an apparently nonlinear binding process. CONCLUSIONS: This work demonstrates that MALDI-TOFMS can be used for direct determination of the binding of surfactant lipids to nanoparticles and represents an important initial step towards a simple and quantitative in vitro method for assessment of interactions of nanoparticles with lung surfactants. [ABSTRACT FROM AUTHOR]

Impregnation spray products are used for making surfaces water and dirt repellent. The products are composed of one or more active film-forming components dissolved or suspended in an appropriate solvent mixture. Exposure to impregnation spray products may cause respiratory distress and new cases are reported frequently. The toxicity appears to be driven by a disruption of the pulmonary surfactant film, which coats the inside of the lungs. Due to the complex chemistry of impregnation spray products, it is impossible to predict if inhalation of an aerosolized product is toxic in vivo. The aim of this study was to evaluate whether disruption of the pulmonary surfactant film can be used as a predictor of the toxic effects in vivo. Nine impregnation products with various chemical compositions were selected for testing and the main constituents of each product, e.g., solvents, co-solvents and film-forming compounds, were identified by mass spectrometry. We used a capillary surfactometry method to assess disruption of pulmonary surfactant function in vitro and a mouse model to evaluate acute respiratory toxicity during inhalation. Concentration-response relationships were successfully determined both in vitro and in vivo. The true positive rate of the in vitro method was 100%, i.e., the test could correctly identify all products with toxic effects in vivo, the true negative rate was 40%. Investigation of inhibition of the pulmonary surfactant system, e.g., by capillary surfactometry, was found useful for evaluation of the inhalation toxicity of impregnation spray products and thus may reduce the need for animal testing. [ABSTRACT FROM AUTHOR]

A low temperature plasma (LTP) ionization interface between a gas chromatograph (GC) and an atmospheric pressure inlet mass spectrometer, was constructed. This enabled time-of-flight mass spectrometric detection of GC-eluting compounds. The performance of the setup was evaluated by injection of mixtures of common volatile organic compounds. Amounts down to ca. 0.5 ng (on column) could be detected for most compounds and with a chromatographic performance comparable to that of GC/EIMS. In the positive mode, LTP ionization resulted in a compound specific formation of molecular ions M+•, protonated molecules [M + H]+, and adduct ions such as [(M + O) + H]+ and [M + NO]+. The ion patterns seemed unique for each of the analyzed compound classes and can therefore be useful for identification of functional groups. A total of 20 different compounds within 8 functional groups were analyzed. [ABSTRACT FROM AUTHOR]

Here, we present emission data on VOCs and particles emitted during simulated use of four commercial nanofilm spray products (NFPs) used for making easy-to-clean or self-cleaning surfaces on floors, ceramic tiles, and windows. The aim was to characterize the emitted VOCs and to provide specific source strength data for VOCs and particles released to the air during use of the products. Containers with NFP were mounted on a spray-stand inside a closed stainless steel chamber with no air exchange. NFPs were sprayed in amounts corresponding to 1 m2 surface toward a target plate at a distance of 35 cm. Released VOCs were measured by a combination of air sampling on Tenax TA adsorbent followed by thermal desorption GC/MS and GC/FID analysis and real time measurements using a miniature membrane inlet mass spectrometer. Particles were measured using a fast mobility particle sizer and an aerosol particle sizer. A number of VOCs were identified, including small alcohols, ketones and ethers, chlorinated acetones, a perfluorinated silane, limonene, and cyclic siloxanes. The number of generated particles was on the - order of 3 x 108 to 2 x 1010 particles/m3 per g sprayed NFP and were dominated by nanosize particles. [ABSTRACT FROM AUTHOR]

Manufactured nanomaterials (MNMs) often have a surface-chemical modification in order to tailor their physicochemical properties, including also powder properties and miscibility. Surface-chemical modifications may influence the toxicological properties of the MNM, but the specific chemistry and extent are rarely described in detail in suppliers' technical data sheets. Chemical and quantitative information on any surface-chemical treatment, coating and functionalization are required for chemicals registration in Europe. Currently there is no globally accepted and documented approach to generate such data. Consequently, there is a continued research need to establish a structured approach to identify and quantify surface-chemical modifications. Here we present a tiered approach starting with screening for mass-loss during heating in a furnace or thermogravimetric analysis (TGA) followed by solvent extraction, and analysis by several mass spectrometry (MS) techniques depending on the target analytes. Thermal treatment was assumed to be able to quantify the amount of organic coating and MS was used to identify the extractable organic coatings after pressurized liquid extraction (PLE) using methanol at 200 °C. Volatile organic compounds in extracts were identified with gas chromatography and MS (GC-MS), non-volatile organic compounds with liquid chromatography MS (LC-MS), and polymeric compounds with matrix-assisted laser desorption ionization time-of-flight MS (MALDI-TOF-MS). The approach was demonstrated by analysis of 24 MNM, comprising titanium dioxide, synthetic amorphous silica, graphite, zinc oxide, silver, calcium carbonate, iron oxide, nickel-zinc-iron oxide, and organoclay. In extracts of 14 MNMs a range of organic compounds were identified and the main groups were silanes/siloxanes, fatty acids, fatty acid esters, quaternary ammonium compounds and polymeric compounds. In the remaining 10 MNMs no organic compounds were detected by MS, despite the fact an organic coating was indicated by TGA. [ABSTRACT FROM AUTHOR]