Search

Modern industrial applications involve rigorous operating conditions due to which lubricant either slips out of the contact or its thin layer resides between the interacting surfaces. Deposition of diamond-like carbon coatings and using lubricants capable of physically adsorbing on the interacting surfaces can significantly improve tribological performance. In this study, tribological compatibility of glycerol mono-oleate, molybdenum dithiocarbamate and zinc dialkyldithiophosphate with palm trimethylolpropane ester and tetrahedral amorphous diamond-like carbon coating has been investigated using universal wear testing machine. For comparison, additive-free and formulated versions of polyalphaolefin were used. Moreover, spectroscopic techniques were used to investigate mechanisms responsible for a particular tribological behavior. Among base oils, trimethylolpropane ester proved to be more effective in enhancing friction performance and mitigating wear of contacts when one of the interacting surfaces was ferrous-based. Self-mated tetrahedral amorphous diamond-like carbon coating surfaces resulted in lowest values of friction and wear coefficient of balls. [ABSTRACT FROM AUTHOR]

The constant utilization of petroleum-based products has prompted concerns about the environment, hence a replacement for these products must be explored. Biolubricants are a suitable replacement for petroleum-based lubricants as they provide better lubricity. Biolubricant performance can be improved by the addition of graphene. However, there are reports that graphene is unable to form a stable suspension for a long period. This study used a graphene-ionic liquid additive combination to stabilize the dispersion in a biolubricant. Graphene and ionic liquid were dispersed into the biolubricant via a magnetic stirrer. The samples were tested using a high frequency reciprocating rig. The cast iron sample was then further observed using various techniques to determine the lubricating mechanism of the lubricant. Different dispersion stability of graphene was observed for different biolubricants, which can be improved with ionic liquids. All ionic liquid samples maintained an absorbance value of three for one month. The utilization of ionic liquid was also able to decrease the frictional performance by 33%. Further study showed that by using the ionic liquid alone, the frictional could only reduce the friction coefficient by 13% and graphene could only reduce the friction by 7%. A smooth worn surface scar can be seen on the graphene-IL sample compared to the prominent corrosive spot on the IL samples and abrasive scars on graphene samples. This indicates synergistic behavior between the two additives. It was found that the ionic liquid does not only improve the dispersion stability, but also plays a role in forming the tribolayer. [ABSTRACT FROM AUTHOR]

This research was aimed to examine the diesel engine's performance and emission of secondary fuels (SFs), comprising waste plastic oil (WPO) and palm oil biodiesel (POB), and to analyze their tribological properties. Their compositions were analyzed by gas chromatography-mass spectrometry (GC-MS). Five SFs (10-50% POB in WPO) were prepared by mechanical stirring. The results were compared to blank WPO (WPO100) and Malaysian commercial diesel (B10). WPO90 showed the maximum brake power (BP) and brake torque (BT) among the SFs, and their values were 0.52 and 0.59% higher compared to B10, respectively. The increase in POB ratio (20-50%) showed a negligible difference in BP and BT. WPO70 showed the lowest brake-specific fuel consumption among the SFs. The brake thermal efficiency (BTE) increased with POB composition. The maximum reductions in emission of hydrocarbon (HC, 37.21%) and carbon monoxide (CO, 27.10%) were achieved by WPO50 among the SFs. WPO90 showed the maximum reduction in CO 2 emission (6.78%). Increasing the POB composition reduced the CO emissions and increased the CO 2 emissions. All SFs showed a higher coefficient of friction (COF) than WPO100. WPO50 showed the minimal increase in COF of 2.45%. WPO90 showed the maximum reduction in wear scar diameter (WSD), by 10.34%, compared to B10. Among the secondary contaminated samples, SAE40-WPO90 showed the lowest COF, with 5.98% reduction compared to SAE40-WPO100. However, with increasing POB content in the secondary contaminated samples, the COF increased. The same trend was also observed in their WSD. Overall, WPO90 is the optimal SF with excellent potential for diesel engines., Competing Interests: The authors declare no competing financial interest., (© 2021 The Authors. Published by American Chemical Society.)