Search

Mesoscale-to-microscale coupling is an important tool for conducting turbulence-resolving multiscale simulations of realistic atmospheric flows, which are crucial for applications ranging from wind energy to wildfire spread studies. Different techniques are used to facilitate the development of realistic turbulence in the large-eddy simulation (LES) domain while minimizing computational cost. Here, we explore the impact of a simple and computationally efficient Stochastic Cell Perturbation method using momentum perturbation (SCPM-M) to accelerate turbulence generation in boundary-coupled LES simulations using the Weather Research and Forecasting model. We simulate a convective boundary layer (CBL) to characterize the production and dissipation of turbulent kinetic energy (TKE) and the variation of TKE budget terms. Furthermore, we evaluate the impact of applying momentum perturbations of three magnitudes below, up to, and above the CBL on the TKE budget terms. Momentum perturbations greatly reduce the fetch associated with turbulence generation. When applied to half the vertical extent of the boundary layer, momentum perturbations produce an adequate amount of turbulence. However, when applied above the CBL, additional structures are generated at the top of the CBL, near the inversion layer. The magnitudes of the TKE budgets produced by SCPM-M when applied at varying heights and with different perturbation amplitudes are always higher near the surface and inversion layer than those produced by No-SCPM, as are their contributions to the TKE. This study provides a better understanding of how SCPM-M reduces computational costs and how different budget terms contribute to TKE in a boundary-coupled LES simulation.

Large‐eddy simulation (LES) has been adopted to study wind turbine wakes because it can capture fine‐scale details of turbulent wind flows and interactions with wind turbines. Here, we use the LES version of the Weather Research and Forecasting (WRF) model with an actuator disk model to gain insights on several wake effects that have been traditionally difficult to measure. The first finding is that the wake has a "dual nature," meaning that the wind speed deficit behaves differently from the added turbulent kinetic energy (TKE) and the two are not co‐located in space. For example, the wind speed deficit peaks at hub height and reaches the ground within 8D (D is the rotor diameter), but added TKE peaks near the rotor tip and generally remains aloft. Second, temperature changes near the ground are driven by the added TKE in the rotor area and by atmospheric stability. The combination of these two factors determines the sign and intensity of the vertical heat flux divergence below the rotor, with convergence and warming associated with stable conditions and weak divergence and modest cooling with unstable conditions. Third, wakes do not expand indefinitely, as suggested by similarity theory applied to the wind speed deficit, but eventually stop expanding and actually contract, at different rates depending on atmospheric stability. The implication of these findings is that, in order to study wakes, it is not sufficient to focus on wind speed deficit alone, because TKE is also important and yet behaves differently from the wind speed deficit. [ABSTRACT FROM AUTHOR]

The influence of the large-scale subsidence rate, S, on the stably stratified atmospheric boundary layer (ABL) over the Arctic Ocean snow/ice pack during clear-sky, winter conditions is investigated using a large-eddy simulation model. Simulations of two 24-h periods are conducted while varying S between 0, 0.001 and 0.002 ms−1, and the resulting quasi-equilibrium ABL structures and evolutions are examined. Simulations conducted with S = 0 yield a boundary layer that is deeper, more strongly mixed and cools more rapidly than the observations. Simulations conducted with S > 0 yield improved agreement with the observations in the ABL height, potential temperature gradients and bulk heating rates. We also demonstrate that S > 0 limits the continuous growth of the ABL observed during quasi-steady conditions, leading to the formation of a nearly steady ABL of approximately uniform depth and temperature. Subsidence reduces the magnitudes of the stresses, as well as the implied eddy-diffusivity coefficients for momentum and heat, while increasing the vertical heat fluxes considerably. Subsidence is also observed to increases the Richardson number to values in excess of unity well below the ABL top.

Wind plants slow down the approaching wind, a phenomenon known as blockage. Wind plant blockage undermines turbine performance for front-row turbines and potentially for turbines deeper into the array. We use large-eddy simulations to characterize blockage upstream of a finite-size wind plant in flat terrain for different atmospheric stability conditions and investigate the physical mechanisms modifying the flow upstream of the turbines. To examine the influence of atmospheric stability, we compare simulations of two stably stratified boundary layers using the Weather Research and Forecasting model in large-eddy simulation mode, representing wind turbines using the generalized actuator disk approach. For a wind plant, a faster cooling rate at the surface, which produces stronger stably stratified flow in the boundary layer, amplifies blockage. As a novelty, we investigate the physical mechanisms amplifying blockage by evaluating the different terms in the momentum conservation equation within the turbine rotor layer. The velocity deceleration upstream of a wind plant is caused by an adverse pressure gradient and momentum advection out of the turbine rotor layer. The cumulative deceleration of the flow upstream of the front-row turbines instigates vertical motions. The horizontal flow is diverted vertically, reducing momentum availability in the turbine rotor layer. Although the adverse pressure gradient upstream of the wind plant remains unchanged with atmospheric stability, vertical advection of horizontal momentum is amplified in the more strongly stable boundary layer, mainly by larger shear of the horizontal velocity, thus increasing the blockage effect. [ABSTRACT FROM AUTHOR]

While numerous modeling studies have focused on the interaction of ocean surface waves with the atmospheric boundary layer, most employ idealized waves that are either monochromatic or synthetically generated from a theoretical wave spectrum, and the atmospheric solvers are typically incompressible. To study wind–wave coupling in real-world scenarios, a model that can simulate both realistic meteorological and wave conditions is necessary. In this paper we describe the implementation of a moving bottom boundary condition into the Weather Research and Forecasting Model for large-eddy simulation applications. We first describe the moving bottom boundary conditions within WRF's pressure-based vertical coordinate system. We then validate our code with idealized test cases that have analytical solutions, including flow over a monochromatic wave with and without viscosity. Finally, we present results from turbulent flows over a moving monochromatic wave with different wave ages, and demonstrate satisfactory agreement of the wave growth rate with results from the literature. We also compare atmospheric stress and wind parameters from two physically equivalent cases. The first specifies a wind moving in the same direction as a propagating wave, while the second involves a stationary wave with the wind adjusted such that the wind relative to the wave is the same as in the first case. Results indicate that the velocity and Reynolds stress profiles for the two cases match, further validating the moving bottom implementation. [ABSTRACT FROM AUTHOR]

Despite recent advances in both coupled fire modeling and measurement techniques to sample the fire environment, the fire–atmosphere coupling mechanisms that lead to fast propagating wildfires remain poorly understood. This knowledge gap adversely affects fire management when wildland fires propagate unexpectedly rapidly and shift direction due to the fire impacts on local wind conditions. In this work, we utilized observational data from the FireFlux2 prescribed burn and numerical simulations performed with a coupled fire–atmosphere model WRF-SFIRE to assess the small-scale impacts of fire on local micrometeorology under moderate wind conditions (10–12 m/s). The FireFlux2 prescribed burn provided a comprehensive observational dataset with in situ meteorological observations as well as IR measurements of fire progression. To directly quantify the effects of fire–atmosphere interactions, two WRF-SFIRE simulations were executed. One simulation was run in a two-way coupled mode in which the heat and moisture fluxes emitted from the fire were injected into the atmosphere, and the other simulation was performed in a one-way coupled mode for which the atmosphere was not affected by the fire. The difference between these two simulations was used to analyze and quantify the fire impacts on the atmospheric circulation at different sections of the fire front. The fire-released heat fluxes resulted in vertical velocities as high as 10.8 m/s at the highest measurement level (20 m above ground level) gradually diminishing with height and dropping to 7.9 m/s at 5.77 m. The fire-induced horizontal winds indicated the strongest fire-induced flow at the lowest measurement levels (as high as 3.3 m/s) gradually decreasing to less than 1 m/s at 20 m above ground level. The analysis of the simulated flow indicates significant differences between the fire-induced circulation at the fire head and on the flanks. The fire-induced circulation was much stronger near the fire head than at the flanks, where the fire did not produce particularly strong cross-fire flow and did not significantly change the lateral fire progression. However, at the head of the fire the fire-induced winds blowing across the front were the strongest and significantly accelerated fire progression. The two-way coupled simulation including the fire-induced winds produced 36.2% faster fire propagation than the one-way coupled run, and more realistically represented the fire progression. [ABSTRACT FROM AUTHOR]

This study investigated the sensitivity of pyrocumulonimbus (PyroCb) induced by the California Creek fire of 2020 to the amount and type of surface fuels, within the WRF‐SFIRE modeling system. Satellite data were used to derive fire arrival times to constrain fire progression, and to augment the fuel characterization with better estimates of combustible vegetation accounting for tree mortality. Machine learning was employed to classify standing dead vegetation from aerial imagery, which was then added as a custom fuel class along with the standard Anderson fuel categories. Simulations using this new fuel class produced a larger and more vigorous PyroCb than the control run, however, still under‐predicted the cloud top. Additional augmentation of fuel mass to represent the accumulation of dead vegetation on the forest floor further improved the simulations, demonstrating the efficacy of representing both dead standing and fallen vegetation to produce more realistic PyroCb and smoke simulations. Plain Language Summary: The fire‐generated thunderstorms (pyrocumulonimbus; pyroCb) often associated with mega‐fires significantly impact both regional air quality and future fire progression. Accumulation of dry and dead vegetation is a major driver of such phenomena. Therefore, improved knowledge of surface fuel characteristic and impacts on fire and pyroCb behavior is critical to enhance both fire management and smoke forecasts. In this study, we simulated the 2020 Creek fire in CA, a fire strongly influenced by accumulated dead vegetation, using the WRF‐SFIRE model. We observed significant improvement in the predicted smoke column extent as a result of implementing the additional fuel category derived from satellite images representing increased fuel load associated with tree mortality. Key Points: A new method is introduced to update surface fuels data by incorporating tree mortalityHigher fuel loading increases heat released from combustion, leading to deeper, wider, and stronger pyroconvective plumesSimulated pyrocumulonimbus and smoke distributions with augmented fuel loading compare well with radar observation [ABSTRACT FROM AUTHOR]

This paper evaluates the representation of turbulence and its effect on transport and dispersion within multiscale and microscale-only simulations in an urban environment. These simulations, run using the Weather Research and Forecasting Model with the addition of an immersed boundary method, predict transport and mixing during a controlled tracer release from the Joint Urban 2003 field campaign in Oklahoma City, Oklahoma. This work extends the results of a recent study through analysis of turbulence kinetic energy and turbulence spectra and their role in accurately simulating wind speed, direction, and tracer concentration. The significance and role of surface heat fluxes and use of the cell perturbation method in the numerical simulation setup are also examined. Our previous study detailed the model development necessary for our multiscale simulations, examined model skill at predicting wind speeds and tracer concentrations, and demonstrated that dynamic downscaling from mesoscale to microscale through a sequence of nested simulations can improve predictions of transport and dispersion relative to a microscale-only simulation forced by idealized meteorology. Here, predictions are compared with observations to assess qualitative agreement and statistical model skill at predicting wind speed, wind direction, tracer concentration, and turbulent kinetic energy at locations throughout the city. We also investigate the scale distribution of turbulence and the associated impact on model skill, particularly for predictions of transport and dispersion. Our results show that downscaled large-scale turbulence, which is unique to the multiscale simulations, significantly improves predictions of tracer concentrations in this complex urban environment. Significance Statement: Simulations of atmospheric transport and mixing in urban environments have many applications, including pollution modeling for urban planning or informing emergency response following a hazardous release. These applications include phenomena with spatial scales spanning from millimeters to kilometers. Most simulations resolve flow only within the urban area of interest, omitting larger scales of turbulence and regional influences. This study examines a method that resolves both the small and large-scale flow features. We evaluate simulation accuracy by comparing predictions with observations from an experiment involving the release of a tracer gas in Oklahoma City, Oklahoma, with emphasis on correctly modeling turbulent fluctuations. Our results demonstrate the importance of resolving large-scale flow features when predicting transport and dispersion in urban environments. [ABSTRACT FROM AUTHOR]

Wind-farm parameterizations in weather models can be used to predict both the power output and farm effects on the flow; however, their correctness has not been thoroughly assessed. We evaluate the wind-farm parameterization of the Weather Research and Forecasting Model with large-eddy simulations (LES) of the wake performed with the same model. We study the impact on the velocity and turbulence kinetic energy (TKE) of inflow velocity, roughness, resolution, number of turbines (one or two), and inversion height and strength. We compare the mesoscale with the LES by spatially averaging the LES within areas correspondent to the mesoscale horizontal spacing: one covering the turbine area and two downwind. We find an excellent agreement of the velocity within the turbine area between the two types of simulations. However, within the same area, we find the largest TKE discrepancies because in mesoscale simulations, the turbine-added TKE has to be highest at the turbine position to be advected downwind. Within the downwind areas, differences between velocities increase as the wake recovers faster in the LES, whereas for the TKE both types of simulations show similar levels. From the various configurations, the impact of inversion height and strength is small for these heights and inversion levels. The highest impact for the one-turbine simulations appears under the low-speed case due to the higher thrust, whereas the impact of resolution is low for the large-eddy simulations but high for the mesoscale simulations. Our findings demonstrate that higher-fidelity simulations are needed to validate wind-farm parameterizations. [ABSTRACT FROM AUTHOR]

With the increasing level of offshore wind energy investment, it is correspondingly important to be able to accurately characterize the wind resource in terms of energy potential as well as operating conditions affecting wind plant performance, maintenance, and lifespan. Accurate resource assessment at a particular site supports investment decisions. Following construction, accurate wind forecasts are needed to support efficient power markets and integration of wind power with the electrical grid. To optimize the design of wind turbines, it is necessary to accurately describe the environmental characteristics, such as precipitation and waves, that erode turbine surfaces and generate structural loads as a complicated response to the combined impact of shear, atmospheric turbulence, and wave stresses. Despite recent considerable progress both in improvements to numerical weather prediction models and in coupling these models to turbulent flows within wind plants, major challenges remain, especially in the offshore environment. Accurately simulating the interactions among winds, waves, wakes, and their structural interactions with offshore wind turbines requires accounting for spatial (and associated temporal) scales from O(1 m) to O(100 km). Computing capabilities for the foreseeable future will not be able to resolve all of these scales simultaneously, necessitating continuing improvement in subgrid-scale parameterizations within highly nonlinear models. In addition, observations to constrain and validate these models, especially in the rotor-swept area of turbines over the ocean, remains largely absent. Thus, gaining sufficient understanding of the physics of atmospheric flow within and around wind plants remains one of the grand challenges of wind energy, particularly in the offshore environment. This paper provides a review of prominent scientific challenges to characterizing the offshore wind resource using as examples phenomena that occur in the rapidly developing wind energy areas off the United States. Such phenomena include horizontal temperature gradients that lead to strong vertical stratification; consequent features such as low-level jets and internal boundary layers; highly nonstationary conditions, which occur with both extratropical storms (e.g., nor'easters) and tropical storms; air--sea interaction, including deformation of conventional wind profiles by the wave boundary layer; and precipitation with its contributions to leading-edge erosion of wind turbine blades. The paper also describes the current state of modeling and observations in the marine atmospheric boundary layer and provides specific recommendations for filling key current knowledge gaps. [ABSTRACT FROM AUTHOR]

Wind plant blockage reduces wind velocity upstream of wind plants, reducing the power generated by turbines adjacent to the inflow, and potentially throughout the plant as well. The nature of the mechanism that amplifies blockage as well as the velocity reductions in both the induction zone and potentially deeper into the array are not well understood. Field observations can provide valuable insight into the characteristics of the induction zone and the mechanisms that amplify it. However, the relatively small velocity reductions that have been measured experimentally pose a challenge in quantifying blockage, especially in onshore environments with flow heterogeneities that may be of the same scale as the blockage effect itself. We simulate the flow around the King Plains wind plant in the relatively simple terrain of Oklahoma, the location of the American WAKE experimeNt, to evaluate wind plant blockage in this environment. Using numerical simulations, we find the largest velocity deceleration (0.64 m s−1; 8%) immediately upstream of the wind plant, and 1% velocity deficits 24 rotor diameters upstream of the first turbine row. We also use virtual measurements upstream of the wind plant to analyze the uncertainties and difficulties in measuring blockage using a scanning lidar on shore. Based on our virtual lidar study, the induction zone of land-based wind plants can be incorrectly estimated using observations if the effects of nonuniform terrain on the flow are not carefully considered. Changes in terrain elevation produce local variations in wind speed (as measured by a scanning lidar) that exceed in magnitude the deceleration within the induction zone. We refer to these local changes in wind speed as terrain effects. A methodology to differentiate between terrain effects and blockage in experimental settings is proposed and evaluated herein, highlighting the difficulties and uncertainties associated with measurement and simulation of blockage in even relatively simple onshore environments. [ABSTRACT FROM AUTHOR]

Terrain-induced flow phenomena modulate wind turbine performance and wake behavior in ways that are not adequately accounted for in typical wind turbine wake and wind plant design models. In this work, we simulate flow over two parallel ridges with a wind turbine on one of the ridges, focusing on conditions observed during the Perdigão field campaign in 2017. Two case studies are selected to be representative of typical flow conditions at the site, including the effects of atmospheric stability: a stable case where a mountain wave occurs (as in 50% of the nights observed) and a convective case where a recirculation zone forms in the lee of the ridge with the turbine (as occurred over 50% of the time with upstream winds normal to the ridgeline). We use the Weather Research and Forecasting Model (WRF), dynamically downscaled from the mesoscale (6.75 km resolution) to microscale large-eddy simulation (LES) at 10m resolution, where a generalized actuator disk (GAD) wind turbine parameterization is used to simulate turbine wakes. We compare the WRF-LES-GAD model results to data from meteorological towers, lidars, and a tethered lifting system, showing good qualitative and quantitative agreement for both case studies. Significantly, the wind turbine wake shows different amounts of vertical deflection from the terrain and persistence downstream in the two stability regimes. In the stable case, the wake follows the terrain along with the mountain wave and deflects downwards by nearly 100m below hub height at four rotor diameters downstream. In the convective case, the wake deflects above the recirculation zone over 40m above hub height at the same downstream distance. Overall, the WRF-LES-GAD model is able to capture the observed behavior of the wind turbine wakes, demonstrating the model's ability to represent wakes over complex terrain for two distinct and representative atmospheric stability classes, and, potentially, to improve wind turbine siting and operation in hilly landscapes. [ABSTRACT FROM AUTHOR]

We investigate the ability of theWeather Research and Forecasting model to perform large-eddy simulation of canonical flows. This is achieved through comparison of the simulation outputs with measurements from sonic anemometers on a 250m meteorological mast located at Østerild, in northern Denmark. Østerild is on a flat and rough area, and for the predominant wind directions, the atmospheric flow can be considered to be close to homogeneous. The idealized simulated flows aim at representing atmospheric boundary layer turbulence under unstable, neutral, and stable stability conditions at the surface, which are statistically significant conditions observed at Østerild. We found that the resolved fields from the simulations appear to have the characteristics of the three stability regimes. Vertical profiles of observed mean wind speeds and direction are well reproduced by the simulations, with the largest differences under near-neutral conditions, where the effect of the subgrid-scale model is evident on the vertical wind shear close to the surface. Vertical profiles of observed eddy fluxes are also well reproduced by the simulations, with the largest differences for the three velocity component variances under stable stability conditions, although nearly always within the observed variability. With regards to turbulent kinetic energy, we find good agreement between observations and simulations at all vertical levels. Simulated and observed velocity spectra match very well and show very similar behavior with height and with atmospheric stability within the low-frequency interval; at the effective resolution, the simulated spectra show the typical drop-off of finite differences. Our findings demonstrate that these idealized simulations reproduce the characteristics of atmospheric stability regimes often observed at a high turbulent and flat site within a direction sector, where the air flows over nearly homogeneous land. [ABSTRACT FROM AUTHOR]

As model grid resolutions move from the mesoscale to the microscale, turbulent structures represented in atmospheric boundary layer simulations change dramatically. At intermediate resolutions, the so-called gray zone, turbulent motions are not resolved accurately, posing a challenge to numerical simulations. The representation of turbulence is also highly sensitive to the choice of closure model. Here, we examine explicit filtering and reconstruction in the gray zone as a technique to better represent atmospheric turbulence. The convective boundary layer is simulated using the Weather Research and Forecasting (WRF) Model with horizontal resolutions ranging from 25 m to 1 km. Four large-eddy simulation (LES) turbulence models are considered: the Smagorinsky model, the TKE-1.5 model, and two versions of the dynamic reconstruction model (DRM). The models are evaluated by their ability to produce consistent mean potential temperature profiles, heat and momentum fluxes, velocity fields, and turbulent kinetic energy spectra as the grids become coarser. The DRM, a mixed model that uses an explicit filtering and reconstruction technique to account for resolvable subfilter-scale (RSFS) stresses, performs very well at resolutions of 500 m and 1 km without any special tuning, whereas the Smagorinsky and TKE-1.5 models produce heavily grid-dependent results. [ABSTRACT FROM AUTHOR]

Coupled mesoscale–microscale simulations are required to provide time-varying weather-dependent inflow and forcing for large-eddy simulations under general flow conditions. Such coupling necessarily spans a wide range of spatial scales (i.e., ~10 m to ~10 km). Herein, we use simulations that involve multiple nested domains with horizontal grid spacings in the terra incognita (i.e., km) that may affect simulated conditions in both the outer and inner domains. We examine the impact on simulated wind speed and turbulence associated with forcing provided by a terrain with grid spacing in the terra incognita. We perform a suite of simulations that use combinations of varying horizontal grid spacings and turbulence parameterization/modeling using the Weather Research and Forecasting (WRF) Model using a combination of planetary boundary layer (PBL) and large-eddy simulation subgrid-scale (LES-SGS) models. The results are analyzed in terms of spectral energy, turbulence kinetic energy, and proper orthogonal decomposition (POD) energy. The results show that the output from the microscale domain depends on the type of turbulence model (e.g., PBL or LES-SGS model) used for a given horizontal grid spacing but is independent of the horizontal grid spacing and turbulence modeling of the parent domain. Simulation using a single domain produced less POD energy in the first few modes compared to a coupled simulation (one-way nesting) for similar horizontal grid spacing, which highlights that coupled simulations are required to accurately pass the mesoscale features into the microscale domain. [ABSTRACT FROM AUTHOR]

A canopy model framework is implemented in the Weather Research and Forecasting Model to improve the accuracy of large-eddy simulations (LES) of the atmospheric boundary layer (ABL). The model includes two options that depend on the scale of surface roughness elements. A resolved canopy model, typically used to model flow through vegetation canopies, is employed when roughness elements are resolved by the vertical LES grid. In the case of unresolved roughness, a modified "pseudocanopy model" is developed to distribute drag over a shallow layer above the surface. Both canopy model options are validated against idealized test cases in neutral stability conditions and are shown to improve surface layer velocity profiles relative to simulations employing Monin–Obukhov similarity theory (MOST), which is commonly used as a surface boundary condition in ABL models. Use of the canopy model framework also leads to increased levels of resolved turbulence kinetic energy and turbulent stresses. Because LES of the ABL has a well-known difficulty recovering the expected logarithmic velocity profile (log law) in the surface layer, particular focus is placed on using the pseudocanopy model to alleviate this issue over a range of model configurations. Tests with varying surface roughness values, LES closures, and grid aspect ratios confirm that the pseudocanopy model generally improves log-law agreement relative to simulations that employ a standard MOST boundary condition. The canopy model framework thus represents a low-cost, easy-to-implement method for improving LES of the ABL. [ABSTRACT FROM AUTHOR]

Topographic effects on radiation, including both topographic shading and slope effects, are included in the Weather Research and Forecasting (WRF) Model, and here they are made compatible with the immersed boundary method (IBM). IBM is an alternative method for representing complex terrain that reduces numerical errors over sloped terrain, thus extending the range of slopes that can be represented in WRF simulations. The implementation of topographic effects on radiation is validated by comparing land surface fluxes, as well as temperature and velocity fields, between idealized WRF simulations both with and without IBM. Following validation, the topographic shading implementation is tested in a semirealistic simulation of flow over Granite Mountain, Utah, where topographic shading is known to affect downslope flow development in the evening. The horizontal grid spacing is 50 m and the vertical grid spacing is approximately 8–27 m near the surface. Such a case would fail to run in WRF with its native terrain-following coordinates because of large local slope values reaching up to 55°. Good agreement is found between modeled surface energy budget components and observations from the Mountain Terrain Atmospheric Modeling and Observations (MATERHORN) program at a location on the east slope of Granite Mountain. In addition, the model captures large spatiotemporal inhomogeneities in the surface sensible heat flux that are important for the development of thermally driven flows over complex terrain. [ABSTRACT FROM AUTHOR]

The sensitivities of idealized large-eddy simulations (LESs) to variations of model configuration and forcing parameters on quantities of interest to wind power applications are examined. Simulated wind speed, turbulent fluxes, spectra and cospectra are assessed in relation to variations in two physical factors, geostrophic wind speed and surface roughness length, and several model configuration choices, including mesh size and grid aspect ratio, turbulence model, and numerical discretization schemes, in three different code bases. Two case studies representing nearly steady neutral and convective atmospheric boundary layer (ABL) flow conditions over nearly flat and homogeneous terrain were used to force and assess idealized LESs, using periodic lateral boundary conditions. Comparison with fast-response velocity measurements at 10 heights within the lowest 100m indicates that most model configurations performed similarly overall, with differences between observed and predicted wind speed generally smaller than measurement variability. Simulations of convective conditions produced turbulence quantities and spectra that matched the observations well, while those of neutral simulations produced good predictions of stress, but smaller than observed magnitudes of turbulence kinetic energy, likely due to tower wakes influencing the measurements. While sensitivities to model configuration choices and variability in forcing can be considerable, idealized LESs are shown to reliably reproduce quantities of interest to wind energy applications within the lower ABL during quasi-ideal, nearly steady neutral and convective conditions over nearly flat and homogeneous terrain. [ABSTRACT FROM AUTHOR]

A generalized actuator line (GAL) wind turbine parameterization is implemented within the Weather Research and Forecasting model to enable high-fidelity largeeddy simulations of wind turbine interactions with boundary layer flows under realistic atmospheric forcing conditions. Numerical simulations using the GAL parameterization are evaluated against both an already implemented generalized actuator disk (GAD) wind turbine parameterization and two field campaigns that measured the inflow and near-wake regions of a single turbine. The representation of wake wind speed, variance, and vorticity distributions is examined by comparing fine-resolution GAL and GAD simulations and GAD simulations at both fine and coarse-resolutions. The higher-resolution simulations show slightly larger and more persistent velocity deficits in the wake and substantially increased variance and vorticity when compared to the coarse-resolution GAD. The GAL generates distinct tip and root vortices that maintain coherence as helical tubes for approximately one rotor diameter downstream. Coarse-resolution simulations using the GAD produce similar aggregated wake characteristics to both finescale GAD and GAL simulations at a fraction of the computational cost. The GAL parameterization provides the capability to resolve near wake physics, including vorticity shedding and wake expansion. [ABSTRACT FROM AUTHOR]

To facilitate multiscale simulation using the Weather Research and Forecasting Model, vertical mesh refinement for one-way concurrent nested simulation was recently introduced. Grid refinement in the vertical dimension removes the requirement of different grid aspect ratios on the bounding versus the nested domain, such that results from refinement are in the horizontal directions only, and thereby can also reduce numerical errors on the bounding domain arising from large aspect ratios in the presence of complex terrain. Herein, the impacts of vertical grid refinement on the evolving downstream flow in nested large-eddy simulations are evaluated in relation to other model configuration choices, including turbulence subfilter-scale (SFS) stress models, mesh configuration, and alternative methods for calculating several near-surface flow parameters. Although vertical nesting requires coarsening of the vertical grid on the bounding domain, leading to a smaller range of resolved turbulence scales in the nest's lateral boundary conditions, parameter values within the nested domains are generally only minimally impacted, relative to nesting using the same vertical grid on each domain. Two dynamic SFS models examined herein generally improved the simulated mean wind speed, turbulence kinetic energy, stresses and spectra, on both domains, and accelerated equilibration rates within nested domains, relative to two constant coefficient models. A new method of extrapolating horizontal velocity components to near-surface locations at nested domain lateral boundaries, and a correction to the calculation of deformation elements near the surface, are each shown to slightly alter the mean parameter values, yet only minimally impact equilibration rates within the nested domain. [ABSTRACT FROM AUTHOR]

The increasing size of wind turbines, with rotors already spanning more than 150 m diameter and hub heights above 100 m, requires proper modeling of the atmospheric boundary layer ( ABL) from the surface to the free atmosphere. Furthermore, large wind farm arrays create their own boundary layer structure with unique physics. This poses significant challenges to traditional wind engineering models that rely on surface-layer theories and engineering wind farm models to simulate the flow in and around wind farms. However, adopting an ABL approach offers the opportunity to better integrate wind farm design tools and meteorological models. The challenge is how to build the bridge between atmospheric and wind engineering model communities and how to establish a comprehensive evaluation process that identifies relevant physical phenomena for wind energy applications with modeling and experimental requirements. A framework for model verification, validation, and uncertainty quantification is established to guide this process by a systematic evaluation of the modeling system at increasing levels of complexity. In terms of atmospheric physics, 'building the bridge' means developing models for the so-called 'terra incognita,' a term used to designate the turbulent scales that transition from mesoscale to microscale. This range of scales within atmospheric research deals with the transition from parameterized to resolved turbulence and the improvement of surface boundary-layer parameterizations. The coupling of meteorological and wind engineering flow models and the definition of a formal model evaluation methodology, is a strong area of research for the next generation of wind conditions assessment and wind farm and wind turbine design tools. Some fundamental challenges are identified in order to guide future research in this area. WIREs Energy Environ 2017, 6:e214. doi: 10.1002/wene.214 For further resources related to this article, please visit the . [ABSTRACT FROM AUTHOR]

Mesoscale atmospheric models are increasingly used for high-resolution (<3 km) simulations to better resolve smaller-scale flow details. Increased resolution is achieved using mesh refinement via grid nesting, a procedure where multiple computational domains are integrated either concurrently or in series. A constraint in the concurrent nesting framework offered by the Weather Research and Forecasting (WRF) Model is that mesh refinement is restricted to the horizontal dimensions. This limitation prevents control of the grid aspect ratio, leading to numerical errors due to poor grid quality and preventing grid optimization. Herein, a procedure permitting vertical nesting for one-way concurrent simulation is developed and validated through idealized cases. The benefits of vertical nesting are demonstrated using both mesoscale and large-eddy simulations (LES). Mesoscale simulations of the Terrain-Induced Rotor Experiment (T-REX) show that vertical grid nesting can alleviate numerical errors due to large aspect ratios on coarse grids, while allowing for higher vertical resolution on fine grids. Furthermore, the coarsening of the parent domain does not result in a significant loss of accuracy on the nested domain. LES of neutral boundary layer flow shows that, by permitting optimal grid aspect ratios on both parent and nested domains, use of vertical nesting yields improved agreement with the theoretical logarithmic velocity profile on both domains. Vertical grid nesting in WRF opens the path forward for multiscale simulations, allowing more accurate simulations spanning a wider range of scales than previously possible. [ABSTRACT FROM AUTHOR]

Growth in wind power production has motivated investigation of wind-farm impacts on in situ flow fields and downstream interactions with agriculture and other wind farms. These impacts can be simulated with both large-eddy simulations (LES) and mesoscale wind-farm parameterizations (WFP). The Weather Research and Forecasting (WRF) model offers both approaches. We used the validated generalized actuator disk (GAD) parameterization in WRF-LES to assess WFP performance. A 12-turbine array was simulated using the GAD model and the WFP in WRF. We examined the performance of each scheme in both convective and stable conditions. The GAD model and WFP produced qualitatively similar wind speed deficits and turbulent kinetic energy ( TKE) production across the array in both stability regimes, though the magnitudes of velocity deficits and TKE production levels were underestimated and overestimated, respectively. While wake growth slowed in the latter half of the WFP array as expected, wakes did not approach steady state by the end of the array as simulated by the GAD model. A sensitivity test involving the deactivation of explicit TKE production by the WFP resulted in turbulence levels within the array well that were below those produced by the GAD in both stable and unstable conditions. Finally, the WFP overestimated downwind power production deficits in stable conditions because of the lack of wake stabilization in the latter half of the array. [ABSTRACT FROM AUTHOR]

Wind turbine impacts on the atmospheric flow are investigated using data from the Crop Wind Energy Experiment (CWEX-11) and large-eddy simulations (LESs) utilizing a generalized actuator disk (GAD) wind turbine model. CWEX-11 employed velocityazimuth display (VAD) data from two Doppler lidar systems to sample vertical profiles of flow parameters across the rotor depth both upstream and in the wake of an operating 1.5 MW wind turbine. Lidar and surface observations obtained during four days of July 2011 are analyzed to characterize the turbine impacts on wind speed and flow variability, and to examine the sensitivity of these changes to atmospheric stability. Significant velocity deficits (VD) are observed at the downstream location during both convective and stable portions of four diurnal cycles, with large, sustained deficits occurring during stable conditions. Variances of the streamwise velocity component, σu, likewise show large increases downstream during both stable and unstable conditions, with stable conditions supporting sustained small increases of σu, while convective conditions featured both larger magnitudes and increased variability, due to the large coherent structures in the background flow. Two representative case studies, one stable and one convective, are simulated using LES with a GAD model at 6m resolution to evaluate the compatibility of the simulation framework with validation using vertically profiling lidar data in the near wake region. Virtual lidars were employed to sample the simulated flow field in a manner consistent with the VAD technique. Simulations reasonably reproduced aggregated wake VD characteristics, albeit with smaller magnitudes than observed, while σu values in the wake are more significantly underestimated. The results illuminate the limitations of using a GAD in combination with coarse model resolution in the simulation of near wake physics, and validation thereof using VAD data. [ABSTRACT FROM AUTHOR]

Recently, an actuator disk parameterization was implemented in the Weather Research and Forecasting (WRF) Model for large eddy simulation (LES) of wind turbine wakes. To thoroughly verify this model, simulations of various types of turbines and atmospheric conditions must be evaluated against corresponding experimental data. In this work, numerical simulations are compared to nacellebased scanning lidar measurements taken in stable atmospheric conditions during a field campaign conducted at a wind farm in the western United States. Using several wake characteristics--such as the velocity deficit, centerline location, and wake width--as metrics for model verification, the simulations show good agreement with the observations. Notable results include a high average velocity deficit, decreasing from 73% at a downwind distance x of 1.2 rotor diameters (D) to 25% at x = 6.6D, resulting from a low average wind speed and therefore high average turbine thrust coefficient. Moreover, the wake width expands from 1.4D at x = 1.2D to 2.3D at x¼6.6D. Finally, new features--namely rotor tilt and drag from the nacelle and tower--are added to the existing actuator disk model in WRFLES. Compared to the rotor, the effect of the tower and nacelle on the flow is relatively small but nevertheless important for an accurate representation of the entire turbine. Adding rotor tilt to the model causes the vertical location of the wake center to shift upward. Continued advancement of the actuator disk model in WRF-LES will help lead to optimized turbine siting and controls at wind farms. [ABSTRACT FROM AUTHOR]

Complete models of the hydrologic cycle have gained recent attention as research has shown interdependence between the coupled land and energy balance of the subsurface, land surface, and lower atmosphere. PF.WRF is a new model that is a combination of the Weather Research and Forecasting (WRF) atmospheric model and a parallel hydrology model (ParFlow) that fully integrates three-dimensional, variably saturated subsurface flow with overland flow. These models are coupled in an explicit, operator-splitting manner via the Noah land surface model (LSM). Here, the coupled model formulation and equations are presented and a balance of water between the subsurface, land surface, and atmosphere is verified. The improvement in important physical processes afforded by the coupled model using a number of semi-idealized simulations over the Little Washita watershed in the southern Great Plains is demonstrated. These simulations are initialized with a set of offline spinups to achieve a balanced state of initial conditions. To quantify the significance of subsurface physics, compared with other physical processes calculated in WRF, these simulations are carried out with two different surface spinups and three different microphysics parameterizations in WRF. These simulations illustrate enhancements to coupled model physics for two applications: water resources and wind-energy forecasting. For the water resources example, it is demonstrated how PF.WRF simulates explicit rainfall and water storage within the basin and runoff. Then the hydrographs predicted by different microphysics schemes within WRF are compared. Because soil moisture is expected to impact boundary layer winds, the applicability of the model to wind-energy applications is demonstrated by using PF.WRF and WRF simulations to provide estimates of wind and wind shear that are useful indicators of wind-power output. [ABSTRACT FROM AUTHOR]

Predicting the response of wind farms to changing flow conditions is necessary for optimal design and operation. In this work, simulation and analysis of a frontal passage through a utility scale wind farm is achieved for the first time using a seamless multi-scale modeling approach. A generalized actuator disk (GAD) wind turbine model is used to represent turbine–flow interaction, and results are compared to novel radar observations during the frontal passage. The Weather Research and Forecasting (WRF) model is employed with a nested grid setup that allows for coupling between multi-scale atmospheric conditions and turbine response. Starting with mesoscale forcing, the atmosphere is dynamically downscaled to the region of interest, where the interaction between turbulent flows and individual wind turbines is simulated with 10 m grid spacing. Several improvements are made to the GAD model to mimic realistic turbine operation, including a yawing capability and a power output calculation. Ultimately, the model is able to capture both the dynamics of the frontal passage and the turbine response; predictions show good agreement with observed background velocity, turbine wake structure, and power output after accounting for a phase shift in the mesoscale forcing. This study demonstrates the utility of the WRF-GAD model framework for simulating wind farm performance under complex atmospheric conditions. [ABSTRACT FROM AUTHOR]

Actuator line model representations of wind turbines reduce the simulation cost of wind farm aerodynamics relative to blade geometry resolving simulations. However, most implementations are code specific and may not have proper load balancing when run in parallel. Here, a generalized actuator line model (GALM) is developed to overcome this implementation drawback of existing approaches. The GALM can be coupled to any existing microscale solver with minimal or no modifications. The coupling of our GALM model with the open-source microscale code CgWind is used to demonstrate both its ease of use and fidelity. The results obtained from the coupled-model simulations are validated for both isolated turbine in wind tunnel experiments and measurements in offshore wind farm. Finally, an operational wind farm over complex terrain is demonstrated. The simulations show that wake meandering and power production are strongly influenced by terrain impacts. Access information for obtaining the code is provided. [ABSTRACT FROM AUTHOR]