Search

Mechanical behavior and failure modes of three-dimensional (3D) stitched composites were experimentally investigated. In addition, a comparative analysis between these materials and equivalent laminates (2D) was accomplished. The 3D composite plates were manufactured using sheets of glass fiber manually sewn with aramid tows and molded with epoxy resin by vacuum-assisted resin transfer molding. Three-points bending, Charpy impact, double cantilever beam (DCB), and short-beam shear (SBS) mechanical tests were carried out on both types of materials. The DCB test results revealed that the action of reinforcement tows inhibited the propagation of the delamination cracks, which led to an increase in the fracture toughness of the 3D composites. However, the damage caused by the stitching process, such as fiber breakage and misalignment as well as crimping, and resin-rich regions, was responsible for reducing the flexural and shear properties of these materials. In addition, it was revealed that the stitching did not influence the impact toughness, although it prevented delamination from quick propagation, avoiding a catastrophic failure, which enhanced the damage tolerance of these materials, mainly for aeronautical applications.

Miriti, derived from the leaves of the Amazon palm tree Mauritia flexuosa, is a foam-like material that can serve as a natural substitute for synthetic foams, offering the advantage of natural internal fiber reinforcement. This study assessed miriti’s mechanical properties and potential applications. With an average specific mass of 63 kg.m–3, miriti is amongst the lightest natural solid materials. Its internal fiber reinforcement provides mechanical properties seven to 30 times higher than synthetic foams of similar density in the parallel-to-grain direction. Miriti is a green material and shows high potential for use in sandwich panel cores, thermal/acoustic applications requiring higher strength and stiffness, and load-bearing walls of small structures. Sustainable management of M. flexuosa by local communities is feasible, promoting their sustainable development. Additionally, miriti can inspire the design of synthetic foams reinforced with internal fibers.

Computational modeling plays an important role in the design of orthopedic implants. In the case of biodegradable magnesium alloys, a modeling approach is required to predict the effects of degradation on the implant’s capacity to provide the desired stabilization of fractured bones. In the present work, a numerical corrosion model is implemented to predict the effects of biodegradation on the structural integrity of temporary trauma implants. A non-local average pitting corrosion model is calibrated based on experimental data collected from in vitro degradation experiments and mechanical testing of magnesium WE43 alloy specimens at different degradation stages. The localized corrosion (pitting) model was implemented by developing a user material subroutine (VUMAT) with the program Abaqus®/Explicit. In order to accurately capture both the linear mechanical reduction in specimen resistance, as well as the non-linear corrosion behavior of magnesium WE43 observed experimentally, the corrosion model was extended by employing a variable corrosion kinetic parameter, which is time-dependent. The corrosion model was applied to a validated case study involving the pull-out test of orthopedic screws and was able to capture the expected loss of screw pull-out force due to corrosion. The proposed numerical model proved to be an efficient tool in the evaluation of the structural integrity of biodegradable magnesium alloys and bone-implant assembly and can be used in future works in the design optimization and pre-validation of orthopedic implants.

Embossing is a functional and strategic process for creating high-quality multi-sensory tissue-paper products. Embossing modifies the sheet surface by generating hill and/or valley designs, changing the third-dimension z with a compressive die. This research work specifically concerns the impact study of the engraving finishing geometry on the final properties of tissue paper. This work led us to conclude that, even though the sheets individually present a higher hand-feel (HF) value for the straight finishing geometry, the highest softness was obtained in the two-ply prototype for the round finishing geometry. Moreover, this study confirmed that the HF value reduces with the increase of the bulk, being more accentuated for the micropattern. Relevant differences could not be seen in the spreading kinetics of the liquid droplets over time. Thus, the finishing geometry of the 3D plates did not impact the absorption kinetics on these samples. The finite element model allows us to understand the effect of the plate pattern and its finishing geometry on the paper, and the simulation results were in accordance with the experimental results, showing the same trend where patterns with a round finishing geometry marked the tissue-paper sheet more than patterns with a straight finishing did.

Embossing is a converting process in which the surface of a tissue paper sheet is changed under high pressure, allowing different functions. In this work, the authors intend to study how the embossing pressure affects the main properties of tissue paper, using a laboratory embossing system. An optimum pressure was achieved at 2.8 bar to this embossing laboratory set-up. The effect of pressure when densifying the paper sheet gives it a gain in mechanical strength but no differences in terms of liquid absorbency. The two embossing patterns present different behaviors but both evidence losses in mechanical and softness properties. On the other hand, the finite element method (FEM) does not show clear evidence of how the pressure affects the paper strength. For the deco die, it is possible to observe that the amount of yielding is slightly higher for lower pressure (2.4 bar), but this plasticity state parameter is very similar for 2.8 bar and 3.2 bar. For the micro die, FEM simulations of the manufacturing pressure do not show a considerable impact on the amount of plasticity state of the material; only for 3.2 bar, it shows a change in the pattern of the plasticity state of the paper during the embossing processes. In the end, to achieve a final product with excellent quality, it is important to make a compromise between the various properties.

The embossing operation is one of the processes of tissue paper converting. The embossing parameters influence the final properties of tissue products, such as mechanical, softness, and bulk. In this study, the influence of the rubber hardness used against the embossing steel rolls with a pattern created by intaglio engraving was studied. Three different configurations of rubber plates stacking, each plate with different hardness, were studied. After embossing, mechanical properties, softness, and bulk were evaluated to analyze the effect of rubbers hardness on these properties. Furthermore, a Finite Element Model of the embossing operation was used that considered the same rubber plates stacking configurations used in experiments, and it was able to replicate the experimental results. This work led us to conclude that the configuration where two rubber plates with different hardness, where the rubber plate with higher hardness is in contact with the tissue paper sheet, has shown to be the best solution to obtain higher softness. These findings support the use of embossing operations rubber rolls with a low hardness internal layer and a high hardness external layer in industry. Thus, finite element models were also shown to be reliable tools to virtually test other configurations, such as, for example, three or more rubber plates with different hardness. Since embossing is one of the tissue paper transformation operations with the greatest impact on the key properties of the final product, this study allows the producer to optimize them by varying the hardness of the rubber roll, as well as its configuration.