Search

Abstract Recent advancements on electrohydrodynamic (EHD) soft pumps demonstrate their applicability to various fluid-driven systems such as soft robots, wearable devices, and stretchable electronics. In particular, fiber type EHD pumps reported more recently is a promising pumping element thanks to their versatile fibrous structure. Yet existing EHD fiber pumps are less stretchable and require sophisticated, complex fabrication equipment, implying opportunity for technology advancement. This paper presents a simplified method to create highly stretchable multifunctional fiber EHD pumps. The method employs highly compliant silicone elastomers for the fiber structure that is formed by simple dipping fabrication process. The fabricated pumps (length of 100 mm, inner diameter 4 mm, and mass 5.3 g) exhibit a high stretchability (up to 40% strain) and flow rate and pressure of 167.4 ± 7.6 mL/min (31.6 mL/min/g) and 4.1 ± 0.6 kPa (0.8 kPa/g), respectively. These performances are comparable or even higher than those of previously reported EHD pumps including fiber types. The output performance of the fabricated pumps remain constant for repeated strain cycles (0–25%, up to 2000 cycles) and bending angle up to 180° (corresponding to curvature of 0–30/m). Moreover, the pumps demonstrate unprecedented functionality as a sensor to distinguish the type of fluid inside the tube and to detect strains by reading the capacitance between the electrodes. The characterization result reveals the sensing ability of the pumps as high repeatability up to 30% strain with negligible hysteresis, which is consistent for 5000 cycles.

Electrohydrodynamic (EHD) pumps are a promising driving source for various fluid-driven systems owing to features such as simple structure and silent operation. The performance of EHD pumps depends on the properties of the working fluid, such as conductivity, viscosity, and permittivity. This implies that the tuning of these parameters in a working fluid can enhance the EHD performance. This study reports a method to modify the properties of a liquid for EHD pumps by mixing an additive. Specifically, dibutyl adipate (DBA) and polyvinyl chloride (PVC) are employed as the working fluid and the additive, respectively. The results show that when the concentration of PVC is 0.2%, the flow rate and pressure at applied voltage of 8 kV take highest value of 7.85 μL/s and 1.63 kPa, respectively. These values correspond to an improvement of 109% and 40% for the flow rate and pressure, respectively, compared to the pure DBA (PVC 0%). When the voltage is 10 kV, the flow rate of 10.95 μL/s and the pressure of 2.07 kPa are observed for DBA with PVC concentration of 0.2%. These values are more than five times higher than those observed for FC40 at the same voltage (2.02 μL/s and 0.32 kPa). The results also suggest that optimal conductivity and viscosity values exist for maximizing the EHD performance of a liquid. This demonstrates the validity of the proposed method for realizing high-performance EHD pumps by using additives in the working fluid.

Dielectric elastomer actuators (DEAs) are a promising actuator technology for soft robotics. As a configuration of this technology, stacked DEAs afford a muscle-like contraction that is useful to build soft robotic systems. In stacked DEAs, dielectric and electrode layers are alternately stacked. Thus, often a dedicated setup with complicated processes or sometimes laborious manual stacking of the layers is required to fabricate stacked actuators. In this study, we propose a method to monolithically fabricate stacked DEAs without alternately stacking the dielectric and electrode layers. In this method, the actuators are fabricated mainly through two steps: 1) molding of an elastomeric matrix containing free-form microfluidic channels and 2) injection of a liquid conductive material that acts as an electrode. The feasibility of our method is investigated via the fabrication and characterization of simple monolithic DEAs with multiple electrodes (2, 4, and 10). The fabricated actuators are characterized in terms of actuation stroke, output force, and frequency response. In the actuators, polydimethylsiloxane (PDMS) and eutectic gallium–indium (EGaIn) are used for the elastomeric matrix and electrode material, respectively. Microfluidic channels are realized by dissolving a three-dimensional printed part suspended in the elastomeric structure. The experimental results show the successful implementation of the proposed method and the good agreement between the measured data and theoretical predication, validating the feasibility of the proposed method.

Background/Purpose: The intracellular enzymes present in the saliva have been studied as markers of periodontal disease. The aim of this study was to establish procedures for using salivary biomarkers as an alternative to the Community Periodontal Index (CPI) for community-based screening for periodontal disease. Materials and methods: The study included 101 adults aged between 19 and 77 years who were undergoing treatment for periodontal disease. We applied analysis of covariance (ANCOVA) to analyze the relationship between Community Periodontal Index (CPI) and levels of salivary factors for the 101 volunteers. Results: Demographic characteristics, including age, number of remaining teeth, and smoking habits, showed a significant correlation with CPI. An overall correlation was shown between CP and both salivary lactate dehydrogenases (LD) and hemoglobin (Hb) levels, when analyzed using continuous demographic variables as covariates. Conclusion: Results indicated that screening with statistical modeling can be an effective tool for detecting periodontal disease.

In this paper, we study the nonequilibrium dynamics of the Bose–Hubbard model with the nearest-neighbor repulsion by using time-dependent Gutzwiller (GW) methods. In particular, we vary the hopping parameters in the Hamiltonian as a function of time, and investigate the dynamics of the system from the density wave (DW) to the superfluid (SF) crossing a first-order phase transition and vice versa. From the DW to SF, we find scaling laws for the correlation length and vortex density with respect to the quench time. This is a reminiscence of the Kibble–Zurek scaling for continuous phase transitions and contradicts the common expectation. We give a possible explanation for this observation. On the other hand from SF to DW, the system evolution depends on the initial SF state. When the initial state is the ground state obtained by the static GW methods, a coexisting state of the SF and DW domains forms after passing through the critical point. Coherence of the SF order parameter is lost as the system evolves. This is a phenomenon similar to the glass transition in classical systems. When the state starts from the SF with small local phase fluctuations, the system obtains a large size DW domain structure with thin domain walls.

In this paper, we study a one-dimensional boson system in a superlattice potential. This system is experimentally feasible by using ultracold atomic gases, and attracts much attention these days. It is expected that the system has a topological phase called a topological Mott insulator (TMI). We show that in strongly-interacting cases, the competition between the superlattice potential and the on-site interaction leads to various TMIs with a non-vanishing integer Chern number. Compared to the hard-core case, the soft-core boson system exhibits rich phase diagrams including various non-trivial TMIs. By using the exact diagonalization, we obtain detailed bulk-global phase diagrams including the TMIs with high Chern numbers and also various non-topological phases. We also show that in adiabatic experimental setups, the strongly-interacting bosonic TMIs exhibit the topological particle transfer, i.e., the topological charge pumping phenomenon, similarly to weakly-interacting systems. The various TMIs are characterized by topological charge pumping as it is closely related to the Chern number, and therefore the Chern number is to be observed in feasible experiments.

Background Extended-spectrum β-lactamase (ESBL)-producing Escherichia coli has been increasingly recognized as the cause of upper urinary tract infection (UTI) in children. We have been using flomoxef at our department since 2017 as the first-line empiric therapy for children diagnosed with UTIs, and we avoid using carbapenems, which are considered the first-line treatment for ESBL-producing E. coli. However, reports on the use of flomoxef for UTIs are limited, especially for pediatric patients. The presence of vesicoureteral reflux at the onset of pyelonephritis is a concern. Severe vesicoureteral reflux can lead to repeated UTI and future deterioration of renal function, but the indication for voiding urethrography, which closely examines the presence of vesicoureteral reflux complications, is controversial. Methods We retrospectively reviewed the laboratory findings, treatment, and clinical course of 96 pyelonephritis cases experienced at our department over a 7-year period from April 2014 to March 2021. Results ESBL-producing E. coli were identified as the cause of pyelonephritis in 51% of cases, and this value was significantly higher (88%) in 2017. No significant differences were found in the febrile period or recurrence rate between the flomoxef-initiated group and other antibiotics groups. We also examined clinical indicators to predict vesicoureteral reflux and found no significant differences in ultrasonographic findings of hydronephrosis. Conclusion In the present series, 51% of all pyelonephritis cases were found to be caused by ESBLproducing E. coli, with a significant increase in recent years. Flomoxef may be a useful alternative to carbapenem for ESBL-producing E. coli and the initial antibiotic of choice for upper UTIs in children. The indication for voiding cystourethrography should be carefully determined. [ABSTRACT FROM AUTHOR]

Uncertainty in hydrological statistics estimated with finite observations, such as design rainfall, can be quantified as a confidence interval using statistical theory. Ensemble climate data also enables derivation of a confidence interval. Recently, the database for policy decision making for future climate change (d4PDF) was developed in Japan, which contains dozens of simulated extreme rainfall events for the past and 60 years into the future, allowing the uncertainty of design rainfall to be quantified as a confidence interval. This study applies an order statistics distribution to evaluate uncertainty in the order statistics of extreme rainfall from the perspective of mathematical theory, while a confidence interval is used for uncertainty evaluation in the probability distribution itself. An advantage of the introduction of an order statistics distribution is that it can be used to quantify the goodness-of-fit between observation and ensemble climate data under the condition that the extreme value distribution estimated from observations is a true distribution. The order statistics distribution is called the control density distribution, which is derived from characteristics that order statistics from standard uniform distribution follows beta distribution. The overlap ratio of the control density distribution and frequency distributions derived from ensemble climate data is utilized for evaluation of the degree of goodness-of-fit for both data. [ABSTRACT FROM AUTHOR]

A concise synthesis of anserine and related compounds was accomplished by Et-DuPhos-Rh-catalyzed asymmetric hydrogenation of dehydrohistidine derivatives in 2,2,2-trifluoroethanol, which played a key role in improving the yield and selectivity. [ABSTRACT FROM AUTHOR]