Search

The mechanical and the electrical properties of polypyrrole (PPy) fibers and electrochemically deposited PPy films were studied. It was found that the PPy fibers showed a significantly higher strength than the PPy films due to better orientation of the molecular structure. The electrochemically prepared PPy films had a higher electrical conductivity than that of the fibers at high temperature. At low temperature, the PPy fibers showed the higher conductivity. The conductivity results were analyzed in the frame of the three-dimensional variable range hopping model. The results showed that at room temperature the average hopping distance for the fibers was about 4 Å while for the films it increases to about 5.7 Å. This corresponds to about 1 and 2 monomer units in length for the fiber and film samples, respectively. [ABSTRACT FROM AUTHOR]

High-performance biocompatible composite materials are gaining attention for their potential in various fields such as neural tissue scaffolds, bio-implantable devices, energy harvesting, and biomechanical sensors. However, these devices currently face limitations in miniaturization, finite battery lifetimes, fabrication complexity, and rigidity. Hence, there is an urgent need for smart and self-powering soft devices that are easily deployable under physiological conditions. Herein, we present a straightforward and efficient fabrication technique for creating flexible/stretchable fiber-based piezoelectric structures using a hybrid nanocomposite of polyvinylidene fluoride (PVDF), reduced graphene oxide (rGO), and barium-titanium oxide (BT). These nanocomposite fibers are capable of converting biomechanical stimuli into electrical signals across various structural designs (knit, braid, woven, and coil). It was found that a stretchable configuration with higher output voltage (4 V) and a power density (87 μW cm -3 ) was obtained using nanocomposite coiled fibers or knitted fibers, which are ideal candidates for real-time monitoring of physiological signals. These structures are being proposed for practical transition to the development of the next generation of fiber-based biomedical devices. The cytotoxicity and cytocompatibility of nanocomposite fibers were tested on human mesenchymal stromal cells. The obtained results suggest that the developed fibers can be utilized for smart scaffolds and bio-implantable devices.

Wearable and implantable active medical devices (WIMDs) are transformative solutions for improving healthcare, offering continuous health monitoring, early disease detection, targeted treatments, personalized medicine, and connected health capabilities. Commercialized WIMDs use primary or rechargeable batteries to power their sensing, actuation, stimulation, and communication functions, and periodic battery replacements of implanted active medical devices pose major risks of surgical infections or inconvenience to users. Addressing the energy source challenge is critical for meeting the growing demand of the WIMD market that is reaching valuations in the tens of billions of dollars. This review critically assesses the recent advances in energy harvesting and storage technologies that can potentially eliminate the need for battery replacements. With a key focus on advanced materials that can enable energy harvesters to meet the energy needs of WIMDs, this review examines the crucial roles of advanced materials in improving the efficiencies of energy harvesters, wireless charging, and energy storage devices. This review concludes by highlighting the key challenges and opportunities in advanced materials necessary to achieve the vision of self-powered wearable and implantable active medical devices, eliminating the risks associated with surgical battery replacement and the inconvenience of frequent manual recharging., (© 2024 The Author(s). Advanced Materials published by Wiley‐VCH GmbH.)

Medical soft robotics constitutes a rapidly developing field in the treatment of cardiovascular diseases, with a promising future for millions of patients suffering from heart failure worldwide. Herein, the present state and future direction of artificial muscle-based soft robotic biomedical devices in supporting the inotropic function of the heart are reviewed, focusing on the emerging electrothermally artificial heart muscles (AHMs). Artificial muscle powered soft robotic devices can mimic the action of complex biological systems such as heart compression and twisting. These artificial muscles possess the ability to undergo complex deformations, aiding cardiac function while maintaining a limited weight and use of space. Two very promising candidates for artificial muscles are electrothermally actuated AHMs and biohybrid actuators using living cells or tissue embedded with artificial structures. Electrothermally actuated AHMs have demonstrated superior force generation while creating the prospect for fully soft robotic actuated ventricular assist devices. This review will critically analyze the limitations of currently available devices and discuss opportunities and directions for future research. Last, the properties of the cardiac muscle are reviewed and compared with those of different materials suitable for mechanical cardiac compression., (© 2023 The Authors. Advanced Materials published by Wiley-VCH GmbH.)

Recent advances in wearable energy harvesting technology as solutions to occupational health and safety programs are presented. Workers are often exposed to harmful conditions-especially in the mining and construction industries-where chronic health issues can emerge over time. While wearable sensors technology can aid in early detection and long-term exposure tracking, powering them and the associated risks are often an impediment for their widespread use, such as the need for frequent charging and battery safety. Repetitive vibration exposure is one such hazard, e.g., whole body vibration, yet it can also provide parasitic energy that can be harvested to power wearable sensors and overcome the battery limitations. This review can critically analyze the vibration effect on workers' health, the limitations of currently available devices, explore new options for powering different personal protective equipment devices, and discuss opportunities and directions for future research. The recent progress in self-powered vibration sensors and systems from the perspective of the underlying materials, applications, and fabrication techniques is reviewed. Lastly, the challenges and perspectives are discussed for reference to the researchers who are interested in self-powered vibration sensors., Competing Interests: The authors declare no conflict of interest., (© 2023 The Authors. Global Challenges published by Wiley‐VCH GmbH.)

An investigation into the addition of different weight percentages of Fe 3 O 4 nanoparticles to find the optimum wt.% and its effect on the microstructure, thermal, magnetic, and electrical properties of aluminum matrix composite was conducted using the powder metallurgy method. The purpose of this research was to develop magnetic properties in aluminum. Based on the obtained results, the value of density, hardness, and saturation magnetization (Ms) from 2.33 g/cm 3 , 43 HV and 2.49 emu/g for Al-10 Fe 3 O 4 reached a maximum value of 3.29 g/cm 3 , 47 HV and 13.06 emu/g for the Al-35 Fe 3 O 4 which showed an improvement of 41.2%, 9.3%, and 424.5%, respectively. The maximum and minimum coercivity (Hc) was 231.87 G for Al-10 Fe 3 O 4 and 142.34 G for Al-35 Fe 3 O 4 . Moreover, the thermal conductivity and electrical resistivity at a high weight percentage (35wt.%) were 159 w/mK, 9.9 × 10 -4 Ω·m, and the highest compressive strength was 133 Mpa.

With the aim of fabricating drug-loaded implantable patches, a 3D printing technique was employed to produce novel coaxial hydrogel patches. The core-section of these patches contained a dopamine-modified methacrylated alginate hydrogel loaded with a chemotherapeutic drug (Gemcitabine), while their shell section was solely comprised of a methacrylated alginate hydrogel. Subsequently, these patches were further modified with CaCO 3 cross linker and a polylactic acid (PLA) coating to facilitate prolonged release of the drug. Consequently, the results showed that addition of CaCO 3 to the formula enhanced the mechanical properties of the patches and significantly reduced their swelling ratio as compared to that for patches without CaCO 3 . Furthermore, addition of PLA coating to CaCO 3 -containing patches has further reduced their swelling ratio, which then significantly slowed down the release of Gemcitabine, to a point where 4-layered patches could release the drug over a period of 7 days in vitro. Remarkably, it was shown that 3-layered and 4-layered Gemcitabine loaded patches were successful in inhibiting pancreatic cancer cell growth for a period of 14 days when tested in vitro. Lastly, in vivo experiments showed that gemcitabine-loaded 4-layered patches were capable of reducing the tumor growth rate and caused no severe toxicity when tested in mice. Altogether, 3D printed hydrogel patches might be used as biocompatible implants for local delivery of drugs to diseased site, to either shrink the tumor or to prevent the tumor recurrence after resection.

Piezoelectric fibers have an important role in wearable technology as energy generators and sensors. A series of hybrid nanocomposite piezoelectric fibers of polyinylidene fluoride (PVDF) loaded with barium-titanium oxide (BT) and reduced graphene oxide (rGO) were prepared via the melt spinning method. Our previous studies show that high-performance fibers with 84% of the electroactive β-phase in the PVDF generated a peak output voltage up to 1.3 V and a power density of 3 W kg -1 . Herein, the dynamic mechanical and creep behavior of these fibers were investigated to evaluate their durability and piezoelectric performance. Dynamic mechanical analysis (DMA) was used to provide phenomenological information regarding the viscoelastic properties of the fibers in the longitudinal direction. DSC and SEM were employed to characterize the crystalline structure of the samples. The storage modulus and the loss tangent increased by increasing the frequency over the temperature range (-50 to 150 °C) for all of the fibers. The storage modulus of the PVDF/rGO nanocomposite fibers had a higher value (7.5 GPa) in comparison with other fibers. The creep and creep recovery behavior of the PVDF/nanofillers in the nanocomposite fibers have been explored in the linear viscoelastic region at three different temperatures (10-130 °C). In the PVDF/rGO nanocomposite fibers, strong sheet/matrix interfacial interaction restricted the mobility of the polymer chains, which led to a higher modulus at temperatures 60 and 130 °C.

Powering miniature robots using actuating materials that mimic skeletal muscle is attractive because conventional mechanical drive systems cannot be readily downsized. However, muscle is not the only mechanically active system in nature, and the thousandfold contraction of eukaryotic DNA into the cell nucleus suggests an alternative mechanism for high-stroke artificial muscles. Our analysis reveals that the compaction of DNA generates a mass-normalized mechanical work output exceeding that of skeletal muscle, and this result inspired the development of composite double-helix fibers that reversibly convert twist to DNA-like plectonemic or solenoidal supercoils by simple swelling and deswelling. Our modeling-optimized twisted fibers give contraction strokes as high as 90% with a maximum gravimetric work 36 times higher than skeletal muscle. We found that our supercoiling coiled fibers simultaneously provide high stroke and high work capacity, which is rare in other artificial muscles., (Copyright © 2021 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.)

Success in making artificial muscles that are faster and more powerful and that provide larger strokes would expand their applications. Electrochemical carbon nanotube yarn muscles are of special interest because of their relatively high energy conversion efficiencies. However, they are bipolar, meaning that they do not monotonically expand or contract over the available potential range. This limits muscle stroke and work capacity. Here, we describe unipolar stroke carbon nanotube yarn muscles in which muscle stroke changes between extreme potentials are additive and muscle stroke substantially increases with increasing potential scan rate. The normal decrease in stroke with increasing scan rate is overwhelmed by a notable increase in effective ion size. Enhanced muscle strokes, contractile work-per-cycle, contractile power densities, and energy conversion efficiencies are obtained for unipolar muscles., (Copyright © 2021 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.)

Flexible substrates have become essential in order to provide increased flexibility in wearable sensors, including polymers, plastic, paper, textiles and fabrics. This study is to comprehensively summarize the bending capabilities of flexible polymer substrate for general Internet of Things (IoTs) applications. The basic premise is to investigate the flexibility and bending ability of polymer materials as well as their tendency to withstand deformation. We start by providing a chronological order of flexible materials which have been used during the last few decades. In the future, the IoT is expected to support a diverse set of technologies to enable new applications through wireless connectivity. For wearable IoTs, flexibility and bending capabilities of materials are required. This paper provides an overview of some abundantly used polymer substrates and compares their physical, electrical and mechanical properties. It also studies the bending effects on the radiation performance of antenna designs that use polymer substrates. Moreover, we explore a selection of flexible materials for flexible antennas in IoT applications, namely Polyimides (PI), Polyethylene Terephthalate (PET), Polydimethylsiloxane (PDMS), Polytetrafluoroethylene (PTFE), Rogers RT/Duroid and Liquid Crystal Polymer (LCP). The study includes a complete analysis of bending and folding effects on the radiation characteristics such as S-parameters, resonant frequency deviation and the impedance mismatch with feedline of the flexible polymer substrate microstrip antennas. These flexible polymer substrates are useful for future wearable devices and general IoT applications.

The ubiquity of wearables, coupled with the increasing demand for power, presents a unique opportunity for nanostructured fiber-based mobile energy storage systems. When designing wearable electronic textiles, there is a need for mechanically flexible, low-cost and light-weight components. To meet this demand, we have developed an all-in-one fiber supercapacitor with a total thickness of less than 100 μm using a novel facile coaxial wet-spinning approach followed by a fiber wrapping step. The formed triaxial fiber nanostructure consisted of an inner poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) core coated with an ionically conducting chitosan sheath, subsequently wrapped with a carbon nanotube (CNT) fiber. The resulting supercapacitor is highly flexible, delivers a maximum energy density 5.83 Wh kg -1 and an extremely high power of 1399 W kg -1 along with remarkable cyclic stability and specific capacitance. This asymmetric all-in-one fiber supercapacitor may pave the way to a future generation of wearable energy storage devices.

There is a significant nascent market for ethically produced products with enormous commercial potential around the world. A reliable method to signal the provenance of products is therefore critical for industry, given that competition based on price is not a viable strategy. The ability to trace and signal ethical treatment of animals is also of significant value to textiles manufactures. The efficacy of such a method can be measured with respect to the cost of implementation, scalability, and the difficulty of counterfeiting. The key to traceability is to win the trust of the consumer about the veracity of this information. Wearable sensors make it possible to monitor and improve the management of traceability and/or provenance. In this paper, we introduce a method for signalling the provenance of garments using radio frequency watermarks. The proposed model consists of two levels of authentication that are easy to use by legitimate vendors, but extremely difficult to imitate or hack, because the watermark is built-in and based on the radiation signature of electroactive materials.

The demands for wearable technologies continue to grow and novel approaches for powering these devices are being enabled by the advent of new energy materials and novel manufacturing strategies. In addition, decreasing the energy consumption of portable electronic devices has created a huge demand for the development of cost-effective and environment friendly alternate energy sources. Energy harvesting materials including piezoelectric polymer with its special properties make this demand possible. Herein, we develop a flexible and lightweight nanogenerator package based on polyvinyledene fluoride (PVDF)/LiCl electrospun nanofibers. The piezoelectric performance of the developed nanogenator is investigated to evaluate effect of the thickness of the as-spun mat on the output voltage using a vibration and impact test. It is found that the output voltage increases from 1.3 V to 5 V by adding LiCl as additive into the spinning solution compared with pure PVDF. The prepared PVDF/LiCl nanogenerator is able to generate voltage and current output of 3 V and 0.5 μA with a power density output of 0.3 μW cm -2 at the frequency of 200 Hz. It is found also that the developed nanogenerator can be utilized as a sensor to measure temperature changes from 30 °C to 90 °C under static pressure. The developed electrospun temperature sensor showed sensitivity of 0.16%/°C under 100 Pa pressure and 0.06%/°C under 220 Pa pressure. The obtained results suggested the developed energy harvesting textiles have promising applications for various wearable self-powered electrical devices and systems.

Pancreatic ductal adenocarcinoma (PDAC) has a dismal prognosis, with surgical resection of the tumor in conjunction with systemic chemotherapy the only potential curative therapy. Up to 80% of diagnosed cases are deemed unresectable, prompting the need for alternative treatment approaches. Herein, coaxial polymeric fibers loaded with two chemotherapeutic agents, gemcitabine (Gem) and paclitaxel (Ptx), are fabricated to investigate the effect of local drug delivery on PDAC cell growth in vitro and in vivo. A wet-spinning fabrication method to form a coaxial fiber with a polycaprolactone shell and alginate core loaded with Ptx and Gem, respectively, is used. In vitro, Gem+Ptx fibers display significant cytotoxicity as well as radiosensitizing properties toward PDAC cell lines greater than the equivalent free drugs, which may be attributed to a radiosensitizing effect of the polymers. In vivo studies assessing Gem+Ptx fiber efficacy found that Gem+Ptx fibers reduce tumor volume in a xenograft mouse model of PDAC. Importantly, no difference in mouse weight, circulating cytokines, or liver function is observed in mice treated with Gem+Ptx fibers compared to the empty fiber controls confirming the safety of the implant approach. With further development, Gem+Ptx fibers can improve the treatment of unresectable PDAC in the future., (© 2020 Wiley-VCH GmbH.)

Biopolymer-based hydrogels have emerged as promising platforms for drug delivery systems (DDSs) due to their inherent biocompatibility, tunable physical properties and controllable degradability. Yet, drug release in majority of these systems is solely contingent on diffusion of drug molecules through the hydrogel, which often leads to burst release of drugs from these systems. Herein, inspired by the chemistry of mussel adhesive proteins, a new generation of coaxial hydrogel fibers was developed that could simultaneously exert both affinity and diffusion control over the release of chemotherapeutic drugs. Specifically, dopamine-modified alginate hydrogel along with chemotherapeutic drugs (doxorubicin or gemcitabine) was used as the main core component to confer affinity-controlled release, while a methacrylated-alginate hydrogel was used as the shell composition to provide the controlled diffusion barrier. It was shown that our coaxial mussel-inspired biofibers yielded biocompatible hydrogel fibers (as indicated by comprehensive in vitro and in vivo experiments) with favourable properties including controlled swelling, and enhanced mechanical properties, when compared against single fibers made from unmodified alginate. Notably, it was observed that these coaxial fibers were capable of releasing the two drugs in a slower manner, when compared to single fibers made from pure alginate, which was partly attributed to stronger interactions of drugs with dopamine-modified alginate (the core element of coaxial fibers) as observed from zeta-potential measurements. It was further shown that these drug-loaded coaxial fibers had optimal anticancer activity both in vitro and in vivo using various pancreatic cancer cell lines. Most remarkably, drug loaded coaxial fibers, particularly doxorubicin-containing fibers, had higher anticancer effect in vivo compared to systemic injection of equivalent dosage of the drugs. Altogether, these biocompatible and robust hydrogel fibers may be further used as neoadjuvant or adjuvant therapies for controlled delivery of chemotherapeutic drugs locally to the tumor sites.

In this study we use a combination of ionic- and photo-cross-linking to develop a fabrication method for producing biocompatible microstructures using a methacrylated gellan gum (a polyanion) and chitosan (a polycation) in addition to lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP) as the photoinitiator. This work involves the development of a low-cost, portable 3D bioprinter and a customized extrusion mechanism for controlled introduction of the materials through a 3D printed microfluidic nozzle, before being cross-linked in situ to form robust microstructure bundles. The formed microstructures yielded a diameter of less than 1 μm and a tensile strength range of ∼1 MPa. This study is the first to explore and achieve GGMA:CHT microstructure fabrication by means of controlled in-line compaction and photo-cross-linking through 3D printed microfluidic channels.

Conductive biomaterials have recently gained much attention, specifically owing to their application for electrical stimulation of electrically excitable cells. Herein, flexible, electrically conducting, robust fibers composed of both an alginate biopolymer and graphene components have been produced using a wet-spinning process. These nanocomposite fibers showed better mechanical, electrical, and electrochemical properties than did single fibers that were made solely from alginate. Furthermore, with the aim of evaluating the response of biological entities to these novel nanocomposite biofibers, in vitro studies were carried out using C2C12 myoblast cell lines. The obtained results from in vitro studies indicated that the developed electrically conducting biofibers are biocompatible to living cells. The developed hybrid conductive biofibers are likely to find applications as 3D scaffolding materials for tissue engineering applications., (Copyright © 2020 Talebian, Mehrali, Raad, Safaei, Xi, Liu and Foroughi.)

Engineering of 3D regenerative skeletal muscle tissue constructs (skMTCs) using hydrogels containing muscle precursor cells (MPCs) is of potential benefit for repairing Volumetric Muscle Loss (VML) arising from trauma (e.g., road/industrial accident, war injury) or for restoration of functional muscle mass in disease (e.g., Muscular Dystrophy, muscle atrophy). Additive Biofabrication (AdBiofab) technologies make possible fabrication of 3D regenerative skMTCs that can be tailored to specific delivery requirements of VML or functional muscle restoration. Whilst 3D printing is useful for printing constructs of many tissue types, the necessity of a balanced compromise between cell type, required construct size and material/fabrication process cyto-compatibility can make the choice of 3D printing a secondary alternative to other biofabrication methods such as wet-spinning. Alternatively, wet-spinning is more amenable to formation of fibers rather than (small) layered 3D-Printed constructs. This study describes the fabrication of biosynthetic alginate fibers containing MPCs and their use for delivery of dystrophin-expressing cells to dystrophic muscle in the mdx mouse model of Duchenne Muscular Dystrophy (DMD) compared to poly(DL-lactic-co-glycolic acid) copolymer (PLA:PLGA) topically-seeded with myoblasts. In addition, this study introduces a novel method by which to create 3D layered wet-spun alginate skMTCs for bulk mass delivery of MPCs to VML lesions. As such, this work introduces the concept of "Trojan Horse" Fiber MTCs (TH-fMTCs) and 3d Mesh-MTCs (TH-mMTCs) for delivery of regenerative MPCs to diseased and damaged muscle, respectively., (Copyright © 2020 Quigley, Cornock, Mysore, Foroughi, Kita, Razal, Crook, Moulton, Wallace and Kapsa.)

There is an urgent need for electrochemical sensor materials that exhibit electrochemically compliant properties while also retaining high durability under physiological conditions. Herein, we demonstrate a novel strip-style electrochemical sensor using reduced graphene oxide (rGO) and poly(ethylene dioxythiophene)/poly(styrene sulfonic acid) (PEDOT/PSS) nanocomposite films. The fabricated rGO-PEDOT/PSS sensor with and without nafion has shown an effective electrochemical response for both selectivity and sensitivity of the serotonin (5-hydroxytryptamine, 5-HT) neurotransmitter. The developed high-performance hybrid graphene/conducting polymer strip sensors are likely to find applications as chip electrochemical sensor devices for patients diagnosed with Alzheimer's disease., Competing Interests: The authors declare no competing financial interest., (Copyright © 2019 American Chemical Society.)

Actuator materials capable of producing a rotational or tensile motion are rare and, yet, rotary systems are extensively utilized in mechanical systems like electric motors, pumps, turbines and compressors. Rotating elements of such machines can be rather complex and, therefore, difficult to miniaturize. Rotating action at the microscale, or even nanoscale, would benefit from the direct generation of torsion from an actuator material. Herein we discuss the advantages of using carbon nanotube (CNT) yarns and/or graphene (G) fibers as novel artificial muscles that have the ability to be driven by the electrochemical charging of helically wound multiwall carbon nanotubes or graphene fibers as well as elements in the ambient environment such as moisture to generate such rotational action. The torsional strain, torque, speed and lifetime have been evaluated under various electrochemical conditions to provide insight into the actuation mechanism and performance. Here the most recent advances in artificial muscles based on sheath-run artificial muscles (SRAMs) are reviewed. Finally, the rotating motion of the CNT yarn actuator and the humidity-responsive twisted graphene fibers have been coupled to a mixer for use in a prototype microfluidic system, moisture management and a humidity switch respectively., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

Given their native-like biological properties, high growth factor retention capacity and porous nature, sulfated-polysaccharide-based scaffolds hold great promise for a number of tissue engineering applications. Specifically, as they mimic important properties of tissues such as bone and cartilage they are ideal for orthopaedic tissue engineering. Their biomimicry properties encompass important cell-binding motifs, native-like mechanical properties, designated sites for bone mineralisation and strong growth factor binding and signaling capacity. Even so, scientists in the field have just recently begun to utilise them as building blocks for tissue engineering scaffolds. Most of these efforts have so far been directed towards in vitro studies, and for these reasons the clinical gap is still substantial. With this review paper, we have tried to highlight some of the important chemical, physical and biological features of sulfated-polysaccharides in relation to their chondrogenic and osteogenic inducing capacity. Additionally, their usage in various in vivo model systems is discussed. The clinical studies reviewed herein paint a promising picture heralding a brave new world for orthopaedic tissue engineering., (Copyright © 2019. Published by Elsevier Ltd.)

Although guest-filled carbon nanotube yarns provide record performance as torsional and tensile artificial muscles, they are expensive, and only part of the muscle effectively contributes to actuation. We describe a muscle type that provides higher performance, in which the guest that drives actuation is a sheath on a twisted or coiled core that can be an inexpensive yarn. This change from guest-filled to sheath-run artificial muscles increases the maximum work capacity by factors of 1.70 to 2.15 for tensile muscles driven electrothermally or by vapor absorption. A sheath-run electrochemical muscle generates 1.98 watts per gram of average contractile power-40 times that for human muscle and 9.0 times that of the highest power alternative electrochemical muscle. Theory predicts the observed performance advantages of sheath-run muscles., (Copyright © 2019 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.)

Given their durability and long-term stability, self-healable hydrogels have, in the past few years, emerged as promising replacements for the many brittle hydrogels currently being used in preclinical or clinical trials. To this end, the incompatibility between hydrogel toughness and rapid self-healing remains unaddressed, and therefore most of the self-healable hydrogels still face serious challenges within the dynamic and mechanically demanding environment of human organs/tissues. Furthermore, depending on the target tissue, the self-healing hydrogels must comply with a wide range of properties including electrical, biological, and mechanical. Notably, the incorporation of nanomaterials into double-network hydrogels is showing great promise as a feasible way to generate self-healable hydrogels with the above-mentioned attributes. Here, the recent progress in the development of multifunctional and self-healable hydrogels for various tissue engineering applications is discussed in detail. Their potential applications within the rapidly expanding areas of bioelectronic hydrogels, cyborganics, and soft robotics are further highlighted., Competing Interests: The authors declare no conflict of interest.

In spite of remarkable improvements in cancer treatments and survivorship, cancer still remains as one of the major causes of death worldwide. Although current standards of care provide encouraging results, they still cause severe systemic toxicity and also fail in preventing recurrence of the disease. In order to address these issues, biomaterial-based implantable drug delivery systems (DDSs) have emerged as promising therapeutic platforms, which allow local administration of drugs directly to the tumor site. Owing to the unique properties of biopolymers, they have been used in a variety of ways to institute biodegradable implantable DDSs that exert precise spatiotemporal control over the release of therapeutic drug. Here, the most recent advances in biopolymer-based DDSs for suppressing tumor growth and preventing tumor recurrence are reviewed. Novel emerging biopolymers as well as cutting-edge polymeric microdevices deployed as implantable antitumor DDSs are discussed. Finally, a review of a new therapeutic modality within the field, which is based on implantable biopolymeric DDSs, is given., (© 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

The demands for new types of artificial muscles continue to grow and novel approaches are being enabled by the advent of new materials and novel fabrication strategies. Self-powered actuators have attracted significant attention due to their ability to be driven by elements in the ambient environment such as moisture. In this study, we demonstrate the use of twisted and coiled wet-spun hygroscopic chitosan fibers to achieve a novel torsional artificial muscle. The coiled fibers exhibited significant torsional actuation where the free end of the coiled fiber rotated up to 1155 degrees per mm of coil length when hydrated. This value is 96%, 362%, and 2210% higher than twisted graphene fiber, carbon nanotube torsional actuators, and coiled nylon muscles, respectively. A model based on a single helix was used to evaluate the torsional actuation behavior of these coiled chitosan fibers.

Electrically conductive scaffolds are of significant interest in tissue regeneration. However, the chemistry of the existing scaffolds usually lacks the bioactive features for effective interaction with cells. In this study, poly(ε-caprolactone) was electrospun into aligned nanofibers with 0.58 µm average diameter. Electrospinning was followed by polypyrrole coating on the surface of the fibers, which resulted in 48 kΩ/sq surface resistivity. An oxygen plasma treatment was conducted to change the hydrophobic surface of the fiber mats into a hydrophilic substrate. The water contact angle was reduced from 136° to 0°, and this change remained on the surface of the material even after one year. An indirect cytotoxicity test was conducted, which showed cytocompatibility of the fibrous scaffolds. To measure the cell growth on samples, fibroblast cells were cultured on fibers for 7 days. The cell distribution and density were observed and calculated based on confocal images taken of the cell culture experiment. The number of cells on the plasma-treated sample was more than double than that of sample without plasma treatment. The long-lasting hydrophilicity of the plasma treated fibers with conductive coating is the significant contribution of this work for regeneration of electrically excitable tissues., Competing Interests: The authors declare no conflict of interest.

Novel nanostructured hybrid electrospun polyacrylonitrile (PAN) yarns with different graphene ratios were prepared using liquid crystal graphene oxide (LCGO) and PAN. It was found that the well-dispersed LCGO were oriented along the fiber axis in an electrified thin liquid jet during electrospinning. The graphene oxide sheets were well dispersed in the polar organic solvent, forming nematic liquid crystals upon increasing concentration. Twisted nanofibers were produced from aligned nanofibrous mats prepared by conventional electrospinning. It was found that the mechanical properties of the twisted nanofiber yarns increased even at very low LCGO loading. This research offers a new approach for the fabrication of continuous, strong, and uniform twisted nanofibers which could show promise in developing a novel carbon fiber precursor., Competing Interests: The authors declare no conflict of interest.

Background/objectives: There has been minimal improvement in the prognosis of pancreatic cancer cases in the past 3 decades highlighting the crucial need for more effective therapeutic approaches. A drug delivery system capable of locally delivering high concentrations of chemotherapeutics directly at the site of the tumor is clearly required. The aim of this study was to fabricate and characterize the biophysical properties of gemcitabine-eluting wet-spun polymeric fibers for localized drug delivery applications., Methods/results: Fibers spun from alginate or chitosan solutions with or without the anticancer drug gemcitabine had a uniform surface area, were internally homogeneous and ranged from 50-120 μm in diameter. Drug encapsulation ranged from 13-52%, depending on the type and concentration of polymer used. Gemcitabine displayed first-order release kinetics where 64-82% of the loaded drug was rapidly released within the first 10 h followed by a sustained release over the next 134 h. A time dependent inhibition of ex vivo tumor spheroid growth and cell viability was observed after incubation with gemcitabine-loaded fibers but not control fibers., Conclusion: With further development these studies could lead to the manufacture of a safe and effective delivery system designed to combat non-resectable pancreatic cancer for which currently there is minimal chance of cure., (Copyright © 2017 IAP and EPC. Published by Elsevier B.V. All rights reserved.)

Wearable energy storage devices are of practical interest, but few have been commercially exploited. Production of electrodes with extended cycle life, as well as high energy and power densities, coupled with flexibility, remains a challenge. Herein, we have demonstrated the development of a high-performance hybrid carbon nanotube (CNT) fiber-based supercapacitor for the first time using conventional wet-spinning processes. Manganese dioxide (MnO 2 ) nanoflakes were deposited onto the as-prepared CNT fibers by electrodeposition to form highly flexible nanocomposites fibers. As-prepared fibers were characterized by electron microscopy, electrical, mechanical, and electrochemical measurements. It was found that the specific capacitance was over 152 F g -1 (156 F cm -3 ), which is about 500% higher than the multi-walled carbon nanotube/MnO 2 yarn-based supercapacitors. The measured energy density was 14.1 Wh kg -1 at a power density of 202 W kg -1 . These values are 232% and 32% higher than the energy density and power density of MWNT/MnO 2 yarn-based supercapacitor, respectively. It was found that the cyclic retention ability was more stable, revealing a 16% increase after 10 000 cycles. Such substantial enhancements of key properties of the hybrid material can be associated with the synergy of CNT and MnO 2 nanoparticles in the fiber structure. The use of wet-spun hybrid CNT for fiber-based supercapacitors has been demonstrated.

The demands for electrochemical sensor materials with high strength and durability in physiological conditions continue to grow and novel approaches are being enabled by the advent of new electromaterials and novel fabrication technologies. Herein, we demonstrate a probe-style electrochemical sensor using highly flexible and conductive multi-walled carbon nanotubes (MWNT) yarns. The MWNT yarn-based sensors can be fabricated onto micro Pt-wire with a controlled diameter varying from 100 to 300 µm, and then further modified with Nafion via a dip-coating approach. The fabricated micro-sized sensors were characterized by electron microscopy, Raman, FTIR, electrical, and electrochemical measurements. For the first time, the MWNT/Nafion yarn-based probe sensors have been assembled and assessed for high-performance dopamine sensing, showing a significant improvement in both sensitivity and selectivity in dopamine detection in presence of ascorbic acid and uric acid. It offers the potential to be further developed as implantable probe sensors.

Highly stretchable, actuatable, electrically conductive knitted textiles based on Spandex (SPX)/CNT (carbon nanotube) composite yarns were prepared by an integrated knitting procedure. SPX filaments were continuously wrapped with CNT aerogel sheets and supplied directly to an interlocking circular knitting machine to form three-dimensional electrically conductive and stretchable textiles. By adjusting the SPX/CNT feed ratio, the fabric electrical conductivities could be tailored in the range of 870 to 7092 S/m. The electrical conductivity depended on tensile strain, with a linear and largely hysteresis-free resistance change occurring on loading and unloading between 0% and 80% strain. Electrothermal heating of the stretched fabric caused large tensile contractions of up to 33% and generated a gravimetric mechanical work capacity during contraction of up to 0.64 kJ/kg and a maximum specific power output of 1.28 kW/kg, which far exceeds that of mammalian skeletal muscle. The knitted textile provides the combination of strain sensing and the ability to control dimensions required for smart clothing that simultaneously monitors the wearer's movements and adjusts the garment fit or exerts forces or pressures on the wearer, according to needs. The developed processing method is scalable for the fabrication of industrial quantities of strain sensing and actuating smart textiles.

Research into the development of artificial heart muscle has been limited to assembly of stem cell-derived cardiomyocytes seeded around a matrix, while nonbiological approaches to tissue engineering have rarely been explored. The aim of the study was to apply electrically contractile polymer-based actuators as cardiomyoplasty for positive inotropic support of the right ventricle. Complex trilayer polypyrrole (PPy) bending polymers for high-speed applications were generated. Bending motion occurred directly as a result of electrochemically driven charging and discharging of the PPy layers. In a rat model (n = 5), strips of polymers (3 × 20 mm) were attached and wrapped around the right ventricle (RV). RV pressure was continuously monitored invasively by direct RV cannulation. Electrical activation occurred simultaneously with either diastole (in order to evaluate the polymer's stand-alone contraction capacity; group 1) or systole (group 2). In group 1, the pressure generation capacity of the polymers was measured by determining the area under the pressure curve (area under curve, AUC). In group 2, the RV pressure AUC was measured in complexes directly preceding those with polymer contraction and compared to RV pressure complexes with simultaneous polymer contraction. In group 1, the AUC generated by polymer contraction was 2768 ± 875 U. In group 2, concomitant polymer contraction significantly increased AUC compared with complexes without polymer support (5987 ± 1334 U vs. 4318 ± 691 U, P ≤ 0.01). Electrically contractile polymers are able to significantly augment right ventricular contraction. This approach may open new perspectives for myocardial tissue engineering, possibly in combination with fetal or embryonic stem cell-derived cardiomyocytes., (Copyright © 2014 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.)

The high cost of powerful, large-stroke, high-stress artificial muscles has combined with performance limitations such as low cycle life, hysteresis, and low efficiency to restrict applications. We demonstrated that inexpensive high-strength polymer fibers used for fishing line and sewing thread can be easily transformed by twist insertion to provide fast, scalable, nonhysteretic, long-life tensile and torsional muscles. Extreme twisting produces coiled muscles that can contract by 49%, lift loads over 100 times heavier than can human muscle of the same length and weight, and generate 5.3 kilowatts of mechanical work per kilogram of muscle weight, similar to that produced by a jet engine. Woven textiles that change porosity in response to temperature and actuating window shutters that could help conserve energy were also demonstrated. Large-stroke tensile actuation was theoretically and experimentally shown to result from torsional actuation.

Artificial muscles are of practical interest, but few types have been commercially exploited. Typical problems include slow response, low strain and force generation, short cycle life, use of electrolytes, and low energy efficiency. We have designed guest-filled, twist-spun carbon nanotube yarns as electrolyte-free muscles that provide fast, high-force, large-stroke torsional and tensile actuation. More than a million torsional and tensile actuation cycles are demonstrated, wherein a muscle spins a rotor at an average 11,500 revolutions/minute or delivers 3% tensile contraction at 1200 cycles/minute. Electrical, chemical, or photonic excitation of hybrid yarns changes guest dimensions and generates torsional rotation and contraction of the yarn host. Demonstrations include torsional motors, contractile muscles, and sensors that capture the energy of the sensing process to mechanically actuate.

Hybrid polypyrrole (PPy)-multi walled carbon nanotube (MWNT) yarns were obtained by chemical and electrochemical polymerization of pyrrole on the surface and within the porous interior of twisted MWNT yarns. The material was characterized by scanning electron microscopy, electrochemical, mechanical and electrical measurements. It was found that the hybrid PPy-MWNT yarns possessed significantly higher mechanical strength (over 740 MPa) and Young's modulus (over 54 GPa) than the pristine MWNT yarn. The hybrid yarns also exhibited substantially higher electrical conductivity (over 235 S cm(-1)) and their specific capacitance was found to be in excess of 60 F g(-1). Measurements of temperature dependence of electrical conductivity revealed semiconducting behaviour, with a large increase of band gap near 100 K. The collected low temperature data are in good agreement with a three-dimensional variable range hopping model (3D-VRH). The improved durability of the yarns is important for electrical applications. The composite yarns can be produced in commercial quantities and used for applications where the electrical conductivity and good mechanical properties are of primary importance., (This journal is © The Royal Society of Chemistry 2012)

Rotary motors of conventional design can be rather complex and are therefore difficult to miniaturize; previous carbon nanotube artificial muscles provide contraction and bending, but not rotation. We show that an electrolyte-filled twist-spun carbon nanotube yarn, much thinner than a human hair, functions as a torsional artificial muscle in a simple three-electrode electrochemical system, providing a reversible 15,000° rotation and 590 revolutions per minute. A hydrostatic actuation mechanism, as seen in muscular hydrostats in nature, explains the simultaneous occurrence of lengthwise contraction and torsional rotation during the yarn volume increase caused by electrochemical double-layer charge injection. The use of a torsional yarn muscle as a mixer for a fluidic chip is demonstrated.