Search

The physics of electrospray has been subject to an intense debate for three decades regarding the ultimate electrokinetics that determines the electric current and the size of the emitted droplets in the steady Taylor cone-jet mode (TCJ). In order to solve with a high degree of accuracy the complete electrokinetic structure of the TCJ, in this work, we have used the full Poisson–Nernst–Planck model electrokinetic equations, which have been solved using a high accuracy numerical scheme. We consider a formulation with no interfacial adsorption of ions, as in Mori & Young (J. Fluid Mech. , vol. 855, 2018, pp. 67–130). Our simulations corroborate Mori and Young's conclusion that the classical leaky dielectric model (LDM) recovers the electrodiffusion theory for weak electrolytes when disregarding ion adsorption at the interface. However, for strong electrolytes, our results differ drastically from those provided by the LDM. In this case, we observe that the ion distribution, and consequently the conductivity in the bulk, can be strongly non-homogeneous. Given the rather universal validity of the LDM experimentally observed so far, we postulate that ion interfacial adsorption must be considered in the case of strong, highly dissociated electrolytes to retrieve the LDM limit, mostly for a cone jet operating in the vicinity of the minimum flow rate. [ABSTRACT FROM AUTHOR]

We report a method to generate steady coaxial jets of immiscible liquids with diameters in the range of micrometer/nanometer size. This compound jet is generated by the action of electro-hydrodynamic (EHD) forces with a diameter that ranges from tens of nanometers to tens of micrometers. The eventual jet breakup results in an aerosol of monodisperse compound droplets with the outer liquid surrounding or encapsulating the inner one. Following this approach, we have produced monodisperse capsules with diameters varying between 10 and 0.15 micrometers, depending on the running parameters., Production and control of droplets and particles of micrometer or even nanometer size with a narrow size distribution are of interest for many applications in science and technology. Usually, these [...]

We present an experimental analysis of electrospray where the standard feeding capillary was re- placed with a hypodermic needle. Both the current intensity and the jet diameter were measured for a variety of leaky-dielectric liquids. The results obtained with a feeding capillary and a hypodermic needle of similar dimen- sions were compared. An increase of the liquid conductivity was measured by assuming that the electric current obeys the same scaling law in both configurations. That increase was likely due to the electrochemical reaction taking place in the needle tip.

Abstract: Fifty patients were scheduled to undergo removal of symmetrically positioned lower third molars in two separate appointments. Meloxicam 7.5 or 15mg was once daily administered in a double-blind, randomized and crossover manner after the surgery for 4 days. Objective and subjective parameters were recorded for comparison of postoperative courses. Patients treated with 7.5mg meloxicam who underwent osteotomy reported higher pain scores at 1.5, 3, 4, 10, 12 and 16h (P < 0.05) and ingested a greater amount of rescue analgesic medication (P < 0.05) than those who did not require osteotomy. A higher percentage of patients who underwent osteotomy medicated with 7.5mg meloxicam needed rescue medication as compared to those who did not require osteotomy (P < 0.05). There was a similar mouth opening at suture removal compared with preoperative values for both doses (P >0.05). There were no significant differences concerning swelling observed on the 2nd or 7th postoperative days in comparison with baseline (P >0.05) between the two doses. Pain, trismus and swelling after lower third molar removal not requiring osteotomy can be successfully controlled by a dose regimen of 7.5mg meloxicam once daily. For more aggressive extractions 15mg meloxicam is advisable. [Copyright &y& Elsevier]

Ethylene, a biologically active natural compound, inhibited aflatoxin accumulation by Aspergillus parasiticus on a solid growth medium in a dose-dependent manner at concentrations of 0.1 to 150 ppm. The activity of the nor-1 promoter (an early aflatoxin gene) was reduced to nondetectable levels by similar quantities of ethylene, suggesting that the inhibitory effect on toxin synthesis occurred, at least in part, at the level of transcription. The inhibitory effect of ethylene on aflatoxin accumulation was also observed when A. parasiticus was grown on raw peanuts. Under similar growth conditions and doses, ethylene strongly inhibited development of asci and ascospores in Aspergillus nidulans, with no detectable effect on Hülle cell formation, conidiation, or sterigmatocystin accumulation. During early growth, A. parasiticus and A. nidulans produced ethylene with approximately twofold higher quantities measured in continuous light than in the dark. 1-Methylcyclopropene (an inhibitor of ethylene receptors in plants), light, CO2, temperature, and growth medium composition altered the effect of ethylene on A. nidulans and A. parasiticus. These observations are consistent with the existence of an ethylene sensor molecule that mediates the function of an ethylene-responsive signaling pathway(s) in Aspergillus. [ABSTRACT FROM AUTHOR]

Coaxial electrospray is a well established procedure to generate coaxial micro- and nano-structures (microcapsules and coaxial fibers). In this work we show the capabilities of a high-precision numerical code using dynamic mapping, analytic Jacobian formulation and the Taylor–Melcher leaky dielectric model (LDM) to deal with real coaxial electrospray configurations. Since the number of parameters involved in the problem is large, we focus on an experimentally tested liquid pair configuration where the thickness, relative position, and end sharpness of the coaxial feeding tubes are geometrical parameters of interest. The effects of those parameters and the voltage applied at the tubes on the coaxial liquid menisci, liquid streamlines, size of jet and core, and electric current are discussed. • The influence of the outlet tube geometry on coaxial electrosprays is studied. • Accurate numerical solutions are given using Taylor–Melcher Leaky Dielectric model • Protruding, flush and recessed tube outlet setups, and edge sharpening are explored • Physical details (streamline patterns, menisci geometries, stresses) are provided [ABSTRACT FROM AUTHOR]

Abstract: Light is a major environmental stimulus that has a broad effect on organisms, triggering a cellular response that results in an optimal adaptation enhancing fitness and survival. In fungi, light affects growth, and causes diverse morphological changes such as those leading to reproduction. Light can also affect fungal metabolism, including the biosynthesis of natural products. In this study we show that in Aspergillus nidulans the effect of light on the production of the sterigmatocystin (ST) toxin depends on the glucose concentration. In cultures grown with 1% glucose and exposed to light, ST production was lower than when grown in the dark. This lower ST production coincided with an elevated rate of cellular damage with partial loss of nuclear integrity and vacuolated cytoplasm. However, in cultures grown with 2% glucose these effects were reversed and light enhanced ST production. Glucose abundance also affected the light-dependent subcellular localization of the VeA (velvet) protein, a key regulator necessary for normal light-dependent morphogenesis and secondary metabolism in Aspergilli and other fungal genera. The role of other VeA-associated proteins, particularly the blue-light-sensing proteins LreA and LreB (WC-1 and WC-2 orthologs), on conidiation could also be modified by the abundance of glucose. We also show that LreA and LreB, as well as the phytochrome FphA, modulate not only the synthesis of sterigmatocystin, but also the production of the antibiotic penicillin. [Copyright &y& Elsevier]