Search

Vesicle fusion was used to deposit mixed dimyristoyl phosphatidylethanolamine–dimyristoyl phosphatidylserine (DMPE–DMPS) phospholipid bilayers on Au electrodes. Bilayer structure and composition, when exposed to aqueous NaF and subject to an applied electrochemical potential, were studied using electrochemical, spectroscopic and neutron reflectivity (NR) techniques. Interfacial capacitance data indicate the formation of compact films. Chronocolometric data show that surface charge is significantly altered by the presence of lipid in the potential range −0.75 < E/V (AgAgCl) < 0.35. NR measurements were made on lipid films in which the hydrocarbon tails were either fully hydrogenous (h-DMPE–h-DMPS) or perdeuterated (d-DMPE–d-DMPS), in each case serially exposed to D2O and H2O electrolytes and subject to different applied potentials. Guided by simulations of candidate interfacial structures, these yield the spatial distributions of lipid and solvent within the layers. Adjacent to the electrode, a compact inner leaflet is formed, with potential-dependent solvent volume fraction in the range 0.09 < S< 0.19; there was no evidence of an intervening water layer. The outer leaflet contains rather more solvent, 0.52 < S< 0.55. NR-derived film thickness and PM-IRRAS intensity data show that the lipid molecules are tilted from the surface normal by ca.26°. Bilayer solvation and charge data show a strong correlation for the inner leaflet and very little for the outer leaflet. [ABSTRACT FROM AUTHOR]

Time-resolved specular neutron reflectivity measurements are presented and interpreted for electroactive polyvinylferrocene (PVF) films subject to potentiodynamic electrochemical control. New data acquisition methodology allows an effective measurement time scale on the order of seconds, which is an improvement over conventional methodology by 2 to 3 orders of magnitude. Reflectivity profiles were obtained for PVF films exposed to aqueous 0.1 M NaClO4in which PVF films are thermodynamically permselective, with contrast variation via H2O and D2O. Irrespective of any model, the raw profiles show chemically reversible film “breathing” due to redox-driven solvent entry and exit during polymer oxidation and reduction, respectively. Modeling reveals three compositionally distinct regions within the polymer film: interfacial regions at the electrode and solution interfaces and a “bulk” interior. The new methodology, supported by simultaneous in situ visible transmission spectroscopy, reveals an unprecedented level of insight into the temporal and spatial mechanistic details of film solvation changes, including a two-stage (de)solvation mechanism for redox switching, differences in interior (in)homogeneity for reduced and oxidized films, and permselectivity failure under dynamic electrochemical conditions for the reduced (but not oxidized) state, in contrast to static conditions that allow permselectivity for both states. [ABSTRACT FROM AUTHOR]

Here we have studied the electrocopolymerisation of binary mixtures of functionalised thiophenes in varying compositions and determined independently for each copolymer the spectroelectrochemical responses and the composition of the material using X-ray photoelectron spectroscopy. We have observed strong correlations between the composition of the copolymer material and the composition of the binary solution from which the polymer was grown. In addition, we have shown that the spectroelectrochemical properties of the copolymers indicate the presence of random copolymer material where the λMax values of the neutral, undoped, polymer scales with composition but also suggest that there may be small amounts of block copolymer or phase-separated mixtures of the homopolymer components. [ABSTRACT FROM AUTHOR]

A combination of XPS, reflectance infrared spectroscopy, and neutron reflectivity measurements has been used to probe the spatial and global extents to which carboxylic acid motifs in electrodeposited conducting polymer films can be functionalized by reaction with vapor phase reagents (a carbodiimide together with trifluoroethanol) with the goal of controlling hydrophobicity. Across a range of polymer deposition and reaction temperatures, neutron reflectivity showed that, surprisingly, functionalization of the polymer matrix at depths >5−10 nm into the polymer film was always significantly lower than at the exposed surface. The most efficient functionalization was found to occur when a low-density polymer matrix was prepared by elution of motifs cleaved from the polymer by base hydrolysis. Finally, when trifluoroethanol functionalization was performed, the macroscopic property of hydrophobicity was related to the surface, internal microstructure, and composition of the reacted films as elucidated by the above combination of probes. [ABSTRACT FROM AUTHOR]

The electropolymerization of trans-[RuCl2(vpy)4](vpy = 4-vinylpyridine) on Au or Pt electrodes was studied by cyclic voltammetry and the electrochemical quartz crystal microbalance (EQCM) technique. Cyclic voltammetry of the monomer in DMSO on Au shows reductions at −2.0 and −2.2 V. Potential cycling over the first wave leads to polymer formation; however, scanning over the second wave leads to desorption of the polymer. These observations were confirmed by EQCM measurements which also revealed a high polymerization efficiency. Electrolysis, EQCM and XPS measurements showed that desorption was associated with substitution of chloride ligands by DMSO when the polymer was in a highly reduced state. The film also showed reversible mass changes due to the oxidation and accompanying ingress of charge-balancing anions and solvent into the film. Measurements on the dried films revealed that large quantities of solvent are trapped in the film during the electropolymerization process. [ABSTRACT FROM AUTHOR]

Lasers are instrumental in advanced bioimaging and Raman spectroscopy. However, they are also well known for their destructive effects on living organisms, leading to concerns about the adverse effects of laser technologies. To implement Raman spectroscopy for cell analysis and manipulation, such as Ramanactivated cell sorting, it is crucial to identify nondestructive conditions for living cells. Here, we evaluated quantitatively the effect of 532-nm laser irradiation on bacterial cell fate and growth at the single-cell level. Using a purpose-built microfluidic platform, we were able to quantify the growth characteristics, i.e., specific growth rates and lag times of individual cells, as well as the survival rate of a population in conjunction with Raman spectroscopy. Representative Gram-negative and Grampositive species show similar trends in response to a laser irradiation dose. Laser irradiation could compromise the physiological function of cells, and the degree of destruction is both dose and strain dependent, ranging from reduced cell growth to a complete loss of cell metabolic activity and finally to physical disintegration. Grampositive bacterial cells are more susceptible than Gram-negative bacterial strains to irradiation-induced damage. By directly correlating Raman acquisition with single-cell growth characteristics, we provide evidence of nondestructive characteristics of Raman spectroscopy on individual bacterial cells. However, while strong Raman signals can be obtained without causing cell death, the variety of responses from different strains and from individual cells justifies careful evaluation of Raman acquisition conditions if cell viability is critical. IMPORTANCE In Raman spectroscopy, the use of powerful monochromatic light in laser-based systems facilitates the detection of inherently weak signals. This allows environmentally and clinically relevant microorganisms to be measured at the single-cell level. The significance of being able to perform Raman measurement is that, unlike label-based fluorescence techniques, it provides a "fingerprint" that is specific to the identity and state of any (unlabeled) sample. Thus, it has emerged as a powerful method for studying living cells under physiological and environmental conditions. However, the laser's high power also has the potential to kill bacteria, which leads to concerns. The research presented here is a quantitative evaluation that provides a generic platform and methodology to evaluate the effects of laser irradiation on individual bacterial cells. Furthermore, it illustrates this by determining the conditions required to nondestructively measure the spectra of representative bacteria from several different groups. [ABSTRACT FROM AUTHOR]