Search

As in other countries, In Brazil, new genetic materials of Eucalyptus spp. and their hybrids are multiplied through cloning. These materials, currently in experimental trials, must undergo several stages to select the best ones for pulp and paper production. Therefore, new studies on wood quality are essential. Therefore, this study aimed to group 11 clones of Eucalyptus spp. wood, from a clonal plantation in the municipality of Palmital, São Paulo State, for the production of paper and cellulose. For this purpose, four trees of each clone of 4-year-old Eucalyptus spp. were collected. From each tree, a log of 1 m in length was taken from the base of the tree, for the study of the characterization of the basic density and cellular dimensions of the wood. The results showed that there were significant differences between clones for basic density, fiber length, vessel element length and fiber wall thickness. The Runkel ratio, wall fraction and stiffness coefficient did not show significant differences between the different genotypes. From the results obtained, we can conclude that clones can be differentiated only by basic density, fiber length, vessel element length and fiber wall thickness. The Runkel index, flexibility coefficient and wall fraction of Eucalyptus spp. were more efficient to group the clones into two groups.

Banana stem is a known alternative to wood for the production of pulp and paper. During the production of paper, it is extremely important to save costs and time while at the same time enhancing quality of produced paper. In the present study, paper was developed from banana stem fiber by optimizing its density. Response surface methodology (RSM) using Box-Behnken design (BBD) was used to determine optimum blending parameters of the developed papers. The influence of banana stem fiber amount (250-1000 g), water amount (1-2liters) and blending time (5-10 min) on paper density was analyzed using software Stat-Ease 360, Version 13. The optimum conditions of banana stem fiber amount, water amount and blending time to achieve a density of 675.75 g/m3 were determined as 461.83 g, 1.31liters, and 8.53 min, respectively. ANOVA results revealed that the quadratic model best fits the density response, with blending time and banana stem fiber amount as the most significant model terms. Linear effects were more predominant than quadratic and interaction effects. The developed density model was in close agreement with experimental findings with an R2 value of 0.9748. Developed paper had cellulosic contents, with volatiles as high as 82.11%wb and 2.11%wb ash composition. Future works on thermal properties of paper are encouraged.

Indonesian municipal solid waste (MSW) is dominated by biodegradable MSW (organic and paper). Due to the degradation process, the physical and hydraulic characteristics of these components can change. It is important to study the physical and hydraulic characteristics of MSW, because landslides occurred in several landfills in Indonesia after heavy rains. Field observations showed that landslides occur due to reduced paper components in the landfill (due to high recycling activities), and cause high percolation of water into the landfill. In the research, 38 samples consisting of two variants of MSW samples (organic and 80% organic + 20% paper), were prepared under the conditions of optimum moisture content. The organic sample of MSW is leaf, while the paper sample of MSW is newspaper, which were shredded to a diameter of about 1 cm. The tests of moisture content, bulk density (in the mould of permeameter), particle size distribution, and permeability were carried out on both sample variants for 90 days, with a test frequency of once in 5 days. The results showed that there was an increase in the moisture content and density, and a decrease in particle size and permeability in both variants of MSW sample. Organic MSW + paper has lower permeability and higher density than organic MSW. This requires further study, because a high paper recycling ratio can lead to a change in the landfill characteristics.

Copyright of Journal of Natural Fibers is the property of Taylor & Francis Ltd and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Abstract The dry strength properties of hot-pressed moist paper improved as stiff high-yield pulp fibers soften and the sheet density increased. Very high wet strength was also achieved without adding strengthening agents. This research focuses on a new hot-pressing methodology based on a steel belt-based pilot cylinder press with infrared heating. The heated steel belt transports the moist paper into the cylinder nip with two adjacent steel rollers with adjustable nip pressure. The temperature ranges up to 300 °C, maximum speed is 5 m/min, maximum pulling force from the steel belt is 70 kN and the line load in the two press nips is 15 kN/m each. High peak pressures are possible due to the hard press nip between steel rolls and steel belt, allowing a good heat transfer to the paper. The long dwell time allows strained drying of the paper which results to high density and high wet strength. Paper samples from high-yield pulps were tested at different nip pressures, temperatures and machine speeds while the dry content was kept constant at about 63%. High nip pressure showed the largest effect on densification and dry strength. While high temperature and long dwell time seem to be most important in achieving high wet strength.

Indonesian municipal solid waste (MSW) is dominated by biodegradable MSW (organic and paper). Due to the degradation process, the physical and hydraulic characteristics of these components can change. It is important to study the physical and hydraulic characteristics of MSW, because landslides occurred in several landfills in Indonesia after heavy rains. Field observations showed that landslides occur due to reduced paper components in the landfill (due to high recycling activities), and cause high percolation of water into the landfill. In the research, 38 samples consisting of two variants of MSW samples (organic and 80% organic + 20% paper), were prepared under the conditions of optimum moisture content. The organic sample of MSW is leaf, while the paper sample of MSW is newspaper, which were shredded to a diameter of about 1 cm. The tests of moisture content, bulk density (in the mould of permeameter), particle size distribution, and permeability were carried out on both sample variants for 90 days, with a test frequency of once in 5 days. The results showed that there was an increase in the moisture content and density, and a decrease in particle size and permeability in both variants of MSW sample. Organic MSW + paper has lower permeability and higher density than organic MSW. This requires further study, because a high paper recycling ratio can lead to a change in the landfill characteristics. [ABSTRACT FROM AUTHOR]

Recent studies of fast growing species grown in PT. Sari Bumi Kusuma, Central Kalimantan, show that based on their fiber dimensions there are five species, namely Endospermum diadenum, Dillenia spp., Adinandra dumosa, Adiandra sp., and Nauclea junghuhnii with good potential for pulp and paper production. The fiber length of those five wood species are was more than 2,200 µm on average. This paper studies the physical properties, fiber dimensions and their chemical contents to predict the paper and pulp quality. The result shows that all of the species were classified in the medium to high density category. All species were classified into the first class quality for pulp and paper. Based on chemical contents, Dillenia sp. is the most suitable species due to its high value of holocellulose and a-cellulose, low lignin content, and its fiber length is about 3,119 µm on average. A. dumosa also has good opportunities because it had the longest fiber lengths (3,137 µm on average) and high value of holocellulose, even though it has the highest lignin content. While Nuclea junghuhnii is less suitable due to low values of holocellulose and a-cellulose.

Abstract The incorporation of recycled papers, paperboards and Tetra Pak as filling materials in brittle matrices presents an interesting approach in the utilization of waste materials for building construction. This paper examines the compressive strength and microstructure of gypsum-bonded wastepaper-based composites. Recycled wastepaper of various types (office paper, magazine paper and newspaper), cardboards, paper boxes and Tetra Pak were shredded to short length strips of about 4 × 18 mm. The shredded materials were used as filling materials in natural gypsum in a ratio of 1:3 (v/v), and water was added to the mix. The paste was formed in cylindrical samples measuring 10 cm in length and 5 cm in diameter. Seven different types of composites were produced depending on the material used. The composite products with newspaper and magazine paper had significantly lower density and compressive strength (p

This article is focused on the impact of different binder mixtures on the performances of paper surface and printability. The coating properties were studied with the chosen silica pigment, and the binder consisted of vinyl acetate copolymer and polyvinyl alcohol with different ratios, followed by the measurement of smoothness, whiteness, and surface strength. The inkjet image quality was assessed using water-based inks. The print density, dot gain, and line quality were analyzed. The results showed that the surface performance and printability were affected by the composition of the binder. With the decrease of vinyl acetate copolymer and the increase of polyvinyl alcohol, the surface smoothness and strength decreased, and the penetration and diffusion of the ink changed as well. When the binder mixture was used with proper ratio, a larger solid density, smaller dot gain, and higher definition can be achieved, which were better than using either one of them alone.

A technique for manufacturing wood heat-insulating material for construction (known as wood delignification) without seriously affecting the cellulosic structure was inspired by the practices of the pulp and paper industry and adapted to the mentioned purpose. Among the numerous known methods of chemical treatment of wood for removing the lignin in the paper industry, the use of the suspension generated by mixing of NaOH, Ca(OH)2, and distilled water at 260 ℃ in an electric oven was adopted. For the first time, oak wood (recycled in the form of sawdust) was chosen as the basic raw material in the wood delignification process due to its large availability in Romania's climatic conditions. Using 58 % oak wood, 23.3 % NaOH, 16.7 % Ca(OH)2, and water addition, the best product had very low values of density (0,024 g·cm-3) and heat conductivity (0.031 W·m-1·K-1) as well as an acceptable value of compression resistance (0.9 MPa) for construction applications. [ABSTRACT FROM AUTHOR]

The literature is flooded with scientific information on most durability properties except water absorption coefficient of masonry units like sandcrete blocks. Also, while waste papers disposal is a systemic problem due to ineffectiveness of waste management system in developing countries, the price of cement is on the increase. This situation, ultimately, causes a bane in achievement of low-cost housing development considering the fact that sandcrete blocks are predominantly used as walling elements for such undertakings. In this study, solid core sandcrete blocks were produced with waste paper ash (WPA) utilized as partial replacement of cement at 5 % and 10 % volumetric levels. Chemically, the WPA was found to show similarity with cement in terms of SiO2, Al2O3, and CaO contents. Density and water absorption coefficient of the block samples were determined. While density ranged from 1682 to 1872 kg/m3, water absorption coefficient varied from 27.04 to 23.49 kg/m2h0.5. Statistically, no significant difference was revealed at p < 0.05 between experimentally-measured water absorption coefficients and those obtained using the model developed for prediction based on density of the samples. Thus, utilization of WPA as described herein could help to reduce the cost of procuring cement and in turn, enhance low-cost building construction. Also, with the developed model (showing dependence of water absorption coefficient on density), durability of sandcrete blocks exposed to moisture –prone environment could be easily predicted. [ABSTRACT FROM AUTHOR]

Stretchable displays based on conventional materials exhibit a trade‐off relationship between the pixel density and the stretchability. In this paper, we have demonstrated overcoming the technological limitations of stretchable displays through the optimization of serpentine‐shaped bridge design and the application of stretchable metal electrodes. The application of stretchable electrodes has increased stretchability by over 30% without compromising pixel density. [ABSTRACT FROM AUTHOR]

The article focuses on a study that was conducted to detect the effect of alkaline peroxide pretreatment on thermomechanical pulp (TMP) rejects. Mechanical pulps have an important place in the paper industry, and rejects refining is a critical step in achieving the desired pulp quality for mechanical value-added papers. It was detected that a total alkali charge of 5.2%, alkaline peroxide pretreatment reduced the specific refining energy by 20%, and increased pulp density and tensile strength, which was resulted due to increased fiber flexibility and conformability.

Copyright of Proceedings of the Estonian Academy of Sciences is the property of Teaduste Akadeemia Kirjastus and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Measured local paper structure—i.e. local basis weight, local thickness, local density and local fiber orientation—has been linked to local strain and local material failure (local temperature increase due to energy dissipation upon fiber–fiber bond failure) measured during tensile testing. The data has been spatially linked through data map registration delivering several thousand 1 × 1 mm 2 paper regions, each containing all measured properties. The relation between local paper structure and resulting local deformation and failure is studied with regression models. Multiple linear regression modeling was used to identify the paper structure related drivers for local concentrations of strain under load and local concentrations of material failure, which are both starting to occur considerably before rupture of the paper. Analyzing the development of local strain in paper we found that regions with higher basis weight and higher fiber orientation in load direction tend to exhibit considerably lower strain during tensile testing. Furthermore, the relation between local strain and local grammage can be predicted with the statistical theory of elasticity. Also regions with higher density have lower local strain, but not as pronounced. The findings for local fiber–fiber bond failure of paper are similar but not equivalent. The strongest correlation exists with local grammage. Local density and local fiber orientation show in turn weaker correlation with local bond failure. Local variations in paper thickness were not relevant in any case. These findings are highlighting the relevance of local fiber orientation and local density variations as structural mechanisms governing paper failure. In the past the focus has been mostly on paper formation. Together with local grammage (formation) they are responsible for the weak spots in paper, and thus cause local concentrations of paper strain and the initiation of failure under tensile load. [ABSTRACT FROM AUTHOR]

Paper-based devices have a wide range of applications in point-of-care diagnostics, environmental analysis, and food monitoring. Paper-based devices can be deployed to resource-limited countries and remote settings in developed countries. Paper-based point-of-care devices can provide access to diagnostic assays without significant user training to perform the tests accurately and timely. The market penetration of paper-based assays requires decreased device fabrication costs, including larger packing density of assays (i.e., closely packed features) and minimization of assay reagents. In this review, we discuss fabrication methods that allow for increasing packing density and generating closely packed features in paper-based devices. To ensure that the paper-based device is low-cost, advanced fabrication methods have been developed for the mass production of closely packed assays. These emerging methods will enable minimizing the volume of required samples (e.g., liquid biopsies) and reagents in paper-based microfluidic devices. [ABSTRACT FROM AUTHOR]

Abstract  In this article, a method for measuring the thermal conductivity of paper using a hot disk system is introduced. To the best of our knowledge, few publications are found discussing the thermal conductivity of a coated paper, although it is important to various forms of today’s digital printing where heat is used for imaging, as well as for toner fusing. This motivated an investigation of the thermal conductivity of paper coating. This study demonstrates that the thermal conductivity is affected by the coating mass and the changes in the thermal conductivity affect toner gloss and density. As the coating mass increases, the thermal conductivity increases. Both the toner gloss and density decrease as the thermal conductivity increases. The toner gloss appears to be more sensitive to the changes in the thermal conductivity. [ABSTRACT FROM AUTHOR]

The properties of recycled paper are strongly affected by shrinking during drying, which depends on the drying conditions. An experimental study of the shrinkage phenomenon during drying of paper is presented. Drying experiments were conducted in a drying oven with controlled temperature. The temperature influence on shrinkage extent, porosity, and apparent density of the paper was evaluated. Structural changes on the paper surface after drying were analyzed by scanning electronic microscopy. Thickness contraction, surface, and volumetric shrinkage were correlated as a function of the moisture content. Lower apparent density values and more porous paper samples were obtained for higher temperatures. [ABSTRACT FROM AUTHOR]

Background: Co-authorship is one of the most tangible forms of research collaboration. A co-authorship network is a social network in which the authors through participation in one or more publication through an indirect path have linked to each other. The present research using the social network analysis studied co-authorship network of 681 articles published in Journal of Research in Medical Sciences (JRMS) during 2008-2012. Materials and Methods: The study was carried out with the scientometrics approach and using co-authorship network analysis of authors. The topology of the co-authorship network of 681 published articles in JRMS between 2008 and 2012 was analyzed using macro-level metrics indicators of network analysis such as density, clustering coefficient, components and mean distance. In addition, in order to evaluate the performance of each authors and countries in the network, the micro-level indicators such as degree centrality, closeness centrality and betweenness centrality as well as productivity index were used. The UCINET and NetDraw softwares were used to draw and analyze the co-authorship network of the papers. Results: The assessment of the authors productivity in this journal showed that the first ranks were belonged to only five authors, respectively. Furthermore, analysis of the co-authorship of the authors in the network demonstrated that in the betweenness centrality index, three authors of them had the good position in the network. They can be considered as the network leaders able to control the flow of information in the network compared with the other members based on the shortest paths. On the other hand, the key role of the network according to the productivity and centrality indexes was belonged to Iran, Malaysia and United States of America. Conclusion: Co-authorship network of JRMS has the characteristics of a small world network. In addition, the theory of 6° separation is valid in this network was also true.

Copyright of China Pulp & Paper is the property of China Pulp & Paper Magazines Publisher and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Density and hardness are physical parameters in the manufacturing of refuse derived fuel (RDF) pellets. In making pellets, a high heating value for the combustion system is desired. This research aimed to analyze the mixture of municipal solid waste to its density and hardness and study its correlation to heating value. The variable used in this research is a mixture of paper waste and garden waste and food scraps and garden waste. The density and hardness for the mix of paper waste and garden waste were 1970.6 to 2474.8 kg/m3 and 37.8-42.8 HA, respectively. The mixture of food waste and garden waste has density and hardness of 1822 to 2276.7 kg/m3 and 17.4-37.8 HA. The correlation between density and hardness on heating values did not reach a significance of 0.05, so there was no strong relationship between density and hardness on heating values. [ABSTRACT FROM AUTHOR]

The study aims to increase the efficiency of mortar mixes and improve their necessary qualities such as strength, density, and durability by using wastepaper as a cement substitute in the form of wastepaper sludge ash (WPSA). Mortars with 20, 25, and 30% cement replacement were tested. Due to less use of cement and greater usage of WPSA, CO2 and SO2 emissions can be reduced. The chemical properties of WPSA were compared to those of Ordinary Portland Cement (OPC). Testing showed that WPSA had similar cementitious properties. Results demonstrate the potential applications of this mortar in a variety of settings where increased toughness and equivalent characteristics are needed while still preserving the environment. [ABSTRACT FROM AUTHOR]

The article examines the effect of temperature fluctuations on the water sorption capacity of the paper materials stored inside a closed solander box. Two boxes, filled with either a stack of corrugated board mounts or mat board mounts, were subjected to cyclic temperature changes at a range of 28 and 56 degrees Celsius. It was found that the boards' water sorption capacity gradually decreased over time, which is assumed to be caused by an increase in density of cellulose during wetting-drying cycles. It concludes that the temperature changes outside a closed box have a distinct effect on the moisture content of the paper materials stored inside the box.

This paper discusses the advantages of OLEDs in pixel scaling and the novel device structures enabled by photolithography. We show the pixel layouts that can be realized by photolithographic patterning, i.e., delta and color strip pixel layout with high pixel density. Further integration of OPD next to an OLED pixel is discussed. Finally, we show the OLED performance after three times OLED patterning steps, which is crucial for the full‐color OLED display realized by photolithography patterning processes. The results suggest that the photolithography patterning process could be a powerful method to further enhance the AMOLED display performance. [ABSTRACT FROM AUTHOR]

Purpose: Scientific collaboration is becoming a common pattern in the social organization of knowledge production. The paper tries to figure out the relationship between scientific collaboration team size and scientific output. Design/methodology/approach: Based on ESI database from year 2009–2019, the paper describes changes of collaboration team size from one author to more than 10 authors in 22 disciplines. Kernel density estimation and multidimensional kernel density estimation method are used to calculate optimal collaboration team size and appropriate collaboration team size in 22 disciplines. As bandwidth is one of the major issues in construction of kernel density estimation, the paper uses five different algorithms to calculate bandwidth. The method with the lowest mean absolute percentage error is chosen. Robustness test is conducted based on different sets of data. Findings: The results show that scientific collaboration becomes more widely and deeply. As time goes by, collaboration team size is becoming larger and larger. Natural science disciplines have larger collaboration team size and faster growth rate than social science disciplines. Considering both qualitative and quantitative measures, the paper proves the universality of optimal and appropriate scientific collaboration team size among 22 disciplines and calculates the specific number. Originality/value: The paper tries to investigate the law of scientific collaboration team size variation and provide a full picture of evolution of collaboration team size among 22 disciplines in 10 years. The paper first applies distribution method to figure out the relationship between scientific collaboration team size and scientific output and provides optimal collaboration team size and appropriate collaboration team size. [ABSTRACT FROM AUTHOR]

A semi‐analytical model is built based on diffraction theory and human angular resolution to quantitatively evaluate the diffraction effect of transparent displays, including micro‐LED and OLED. By optimizing the pixel structures within a 2×2‐pixel size region, the relative diffraction intensity is reduced by 42% at the 50% aperture ratio regardless ofpixel density. [ABSTRACT FROM AUTHOR]

Automated color measurement systems have become significant components of offset lithographic printing presses for better process control and reduced job waste. Some European press manufacturers are known to offer automated color measurement equipment that is confined to polarized density readings, which is uncommon in US. Introducing polarized densitometry into an environment where unpolarized densitometry is utilized can be problematic. Print professionals are on the lookout for a solution that is evidenced by a recent feature in a post from the IDEAlliance G7 Professionals forum seeking for a methodology to convert polarized to unpolarized readings. The present study applies the Bland–Altman method together with other statistical analyses to determine if a conversion between polarized and unpolarized densitometry can be established within a limited set of parameters. Three spectrodensitometers were used to record densitometric readings of wet and dry process inks on coated and uncoated drawdown proofs. The results showed that coated papers had significantly less variation between instruments compared to uncoated papers. Wet inks had more minor variations compared to dry inks. Furthermore, pure difference values and a Mann–Whitney U test indicated differences between unpolarized and polarized densitometric readings in all cases. Finally, t‐tests performed on the resulting difference data for both unpolarized versus polarized and unpolarized versus predicted polarized that showed fixed bias by means of the computed p‐values. [ABSTRACT FROM AUTHOR]

Copyright of Teknoloji is the property of Engineering Science & Technology, an International Journal and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The aim of this study was to quantify 5-year growth, yield and mortality responses of 9- to 13-year-old naturally regenerated, even-aged paper birch (Betula papyrifera Marsh.) stands to pre-commercial thinning in interior British Columbia. The study included four residual densities (9902–21,807 stems ha−1 (unthinned control), 3000, 1000 and 400 stems ha−1) and four sites with 3-fold within-site replication in a randomised block design. The largest, straightest, undamaged trees were selected to leave during thinning. Thinning reduced stand basal area from 5.90 m2 ha−1 in the control to 2.50, 1.53 and 0.85 m2 ha−1 in the three thinning treatments, representing 42, 26 and 15% of control basal area, respectively. After 5 years, total stand volume per plot remained lower in the three thinning treatments than the control (50.20, 30.07, 18.99 and 11.86 m3 in the control, 3000, 1000 and 400 stems ha−1 treatments), whereas mean stand diameter, diameter increment, height, and height increment were increased by thinning, and top height (tallest 100 trees ha−1) was unaffected. When a select group of crop trees (largest 250 trees ha−1) in the thinning treatments was compared with the equivalent group in the control, there was a significant increase in mean diameter, diameter increment, basal area, basal area increment, and volume increment. Mean height, height increment, top height, and total volume were unaffected by thinning. Crop tree diameter increment was the greatest following thinning to 400 stems ha−1 for all diameter classes. Thinning to 1000 stems ha−1 resulted in lower diameter increment than thinning to 400 stems ha−1 but tended to have higher volume increment. Dominant trees responded similarly to subdominant trees at 400 stems ha−1, but showed the greatest response at 3000 stems ha−1. Results suggest that pre-commercial thinning of 9–13-year-old stands to 1000 stems ha−1 would improve growth of individual trees without seriously under-utilising site resources. [Copyright &y& Elsevier]

Copyright of China Forest Products Industry is the property of China Forest Products Industry Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The pulping properties of cypress species are not known and the present paper aims to filling this gap. Namely, Cupressus lusitanica Mill., C. sempervirens L. and C. arizonica Greene have been submitted to kraft pulping and the pulp properties are compared with those of Pinus pinaster Aiton. and P. sylvestris Watereri as references. Schopper Riegler degree, density, Bekk's smoothness, tensile index, tear index, burst index, stretch, dry zero-span strength, wet zero-span strength, brightness, opacity and light scattering coefficient have been tested. The pulp yields and delignification degrees of cypress woods were lower than those of the pine references. Fibre length, width and coarseness were statistically different between pines and cypress species and C. sempervirens pulps have corresponding data close to those of pine species. Cypress pulps can be refined much faster than pine pulps. The papers sheets of cypress fibres have, in general, lower mechanical performance than those of pine fibres. Papers from C. arizonica and C. lusitanica are similar and C. sempervirens has intermediate properties being between the other cypress and pine species. However, cypress fibres are relatively short, flexible and collapsible and can be refined with low energy demand, and thus could be incorporated into papers resulting in products with better light scattering and smoothness. [ABSTRACT FROM AUTHOR]