Search

Humanitarian actors involved in physical rehabilitation, such as the International Committee of the Red Cross (ICRC), usually provide their beneficiaries with lower-limb prostheses comprising Solid Ankle Cushion Heel (SACH) feet as these are considered appropriate (price, durability, low profile to fit a majority of patients, appearance) and reliable for all ambulation levels. However, individuals in low-resource settings having higher ambulation abilities would greatly benefit from dynamic prosthetic feet with improved biomechanics and energy storage and release. Some attempts tried to address this increasing need (e.g. Niagara Foot) but most products proposed by large manufacturers often remain unaffordable and unsuitable to the context of low-resource settings. The design requirements and a price target were defined in partnership with the ICRC according to their initial assessment and used as a starting point for the development process and related technological choices. Numerical simulation and modeling were used to work on the design and to determine the required materials properties (mechanical, chemical, wear), and a cost modeling tool was used to select suitable materials and relevant processing routes (price vs. performance). A prosthetic foot comprising an internal keel made of composite materials, a filling foam, and a cosmetic shell with a foot shape was developed. Manufacturing processes meeting the cost criteria were identified and prototype feet were produced accordingly. These were successfully tested using a compression testing system before gait analyses were performed in the laboratory with non-amputees wearing testing boots. After validation in laboratory conditions, the prototype foot was tested in the field (Vietnam) with 11 trans-tibial unilateral amputees, who showed an increased mobility compared with the SACH foot. The collaboration of different research fields led to the development of a prosthetic foot which met the technical requirements determined by the ICRC's specific needs in its field of operation. The materials and selected production processes led to a manufacturing cost of less than 100 USD per part., Competing Interests: The authors have declared that no competing interests exist.

Hygro-thermal ageing of composite materials introduces a modification in the material properties of its constituents and the development of stresses that can lead to severe local damage like fracture of the reinforcing fibers and de-bonding of the latter from the matrix. The study of the complex stress field generated by this induced damage is helpful in designing more resistant materials. Modelling strain-stress filed in the vicinity of these discontinuities has led to the development of different analytical models like for instance shear lag models based on simplification assumptions. Recently the development of embedded optical sensors allowed to shed light on the assumptions made, since they can be used, at the same time, as reinforcement and sensors and thus being capable to give information on the strain distributions during the evolution of the damage. In this work a single fiber composite, whose reinforcement is an optical sensor, is used in order to investigate the complex strain field generated by the fiber fracture caused by the matrix swelling during water uptake.

The durability and reliability of lead-free solder joints depends on a large number of factors, like geometry, processing parameters, microstructure and thermomechanical loads. In this work, the nature and influence of the plastic constraints in the solder due to joining partners have been studied by parametric finite element simulation of solder joints with different dimensions. The apparent hardening due to plastic constraints has been shown to strongly depend on the solder gap to thickness ratio with an inversely proportional evolution. Due to interaction of several parameters, the macroscopic stress–strain constitutive law of lead-free solder materials should be determined in the most realistic conditions. In order to identify the elasto-plastic constitutive law of Sn–Ag–Cu solders, a sub-micron resolution Digital Image Correlation technique has been developed to measure the evolution of strain in solder joints during a tensile test. Experimental results of the stress–strain response of Sn–Ag–Cu solder joints have been determined for several solder gaps. The measured load–displacement curves have been used in an inverse numerical identification procedure to determine the constitutive elasto-plastic behaviour of the solder material. The effects of geometrical constraints in a real solder joint with heterogeneous stress and strain fields are then studied by comparing the apparent (constrained) and constitutive (non-constrained) stress–strain relationships. Once the size dependant constraining effects have been removed from the stress–strain relationship, the scale effects can be studied separately by comparing the constitutive elasto-plastic parameters of joints with a variable thickness. Experimental stress–strain curves (constrained and unconstrained) for Sn–4.0Ag–0.5Cu solder in joints of 0.25–2.4 mm gap are presented and the constraining and the size effects are discussed. [ABSTRACT FROM AUTHOR]

It is widely known that glass–epoxy laminates are renowned for their high stiffness, good thermal properties, and economic qualities. For this reason, composite materials find successful applications in various industrial sectors such as aerospace, astronautics, the storage sector, and energy. The aim of this study was to investigate the mechanical and thermal properties of composite materials comprising two different types of epoxy resin and three different hardeners, both at room temperature and under cryogenic conditions. The samples were produced at IZOERG (Gliwice, Poland) using a laboratory hot-hydraulic-press technique. During cyclic loading–unloading tests, degradation up to a strain level of 0.6% was observed both at room temperature (RT) and at 77 K. For a glass-reinforced composite with YDPN resin (EP_1_1), the highest degradation was recorded at 18.84% at RT and 33.63% at 77 K. We have also investigated the temperature dependence of thermal conductivity for all samples in a wide temperature range down to 5 K. The thermal conductivity was found to be low and had a relative difference of up to 20% among the composites. The experimental results indicated that composites under cryogenic conditions exhibited less damage and were stiffer. It was confirmed that the choice of hardener significantly influenced both properties. [ABSTRACT FROM AUTHOR]

Biomaterials are constructed from limited sets of building blocks but exhibit extraordinary and versatile properties, because hierarchical structure formation lets them employ identical supramolecular motifs for different purposes. Here we exert a similar degree of structural control in synthetic supramolecular elastomers and thus tailor them for a broad range of thermomechanical properties. We show that oligopeptide-terminated polymers selectively self-assemble into small aggregates or nanofibrils, depending on the length of the oligopeptides. This process is self-sorting if differently long oligopeptides are combined so that different nanostructures coexist in bulk mixtures. Blends of polymers with oligopeptides matching in length furnish reinforced elastomers that exhibit shear moduli one order of magnitude higher than the parent polymers. By contrast, novel interpenetrating supramolecular networks that display excellent vibration damping properties are obtained from blends comprising non-matching oligopeptides or unmodified polymers. Hence, blends of oligopeptide-modified polymers constitute a toolbox for tailored elastomers with versatile properties.

Purpose: To assess the effect of external mechanical microstimuli of controlled magnitude on the microarchitecture of the peri-implant bone beds in rat tibiae., Materials and Methods: Tibiae of forty rats were fitted with two transcutaneous titanium cylinders. After healing, the implants were loaded to 1 to 3 N, five days/week for four weeks. These force levels translated into intraosseous strains of 700 ± 200 με, 1400 ± 400 με, and 2100 ± 600 με. After sacrifice, the implants' pullout strength was assessed. Second, the bone's microarchitecture was analyzed by microcomputed tomography (μCT) in three discrete regions of interest (ROIs). Third, the effect of loading on bone material properties was determined by nanoindentation., Results: The trabecular BV/TV significantly increased in an ROI of 0.98 mm away from the test implant in the 1 N versus the 3 N group with an opposite trend for cortical thickness. Pull-out strength significantly increased in the 2 N relatively to the nonstimulated group. Higher values of E-modulus and hardness were observed in the trabecular bone of the 2 N group., Conclusion: The in vivo mechanical loading of implants induces load-dependent modifications in bone microarchitecture and bone material properties in rat tibiae. In pull-out strength measurements, implant osseointegration was maximized at 2 N (1400 ± 400 με).

The periodontal ligament (PDL) is a highly vascularized soft connective tissue. Previous studies suggest that the viscous component of the mechanical response may be explained by the deformation-induced collapse and expansion of internal voids (i.e. chiefly blood vessels) interacting with liquids (i.e. blood and interstitial fluids) flowing through the pores. In the present work we propose a methodology by means of which the morphology of the PDL vascular plexus can be monitored at different levels of compressive and tensile strains. To this end, 4-mm-diameter cylindrical specimens, comprising layers of bone, PDL and dentin covered by cementum, were strained at stretch ratios ranging from lambda = 0.6 to lambda = 1.4 and scanned using synchrotron radiation-based computer tomography. It was concluded that: (1) the PDL vascular network is layered in two distinct planes of blood vessels (BVs): an inner layer (close to the tooth), in which the BVs run in apico-coronal direction, and an outer layer (close to the alveolar bone), in which the BVs distribution is more diffuse; (2) during tension and compression, the porosity tissue is kept fairly constant; (3) mechanical straining induces important changes in BV diameters, possibly modifying the permeability of the PDL and thus contributing to the viscous component of the viscoelastic response observed under compressive forces.

Mode II (in-plane-shear) delamination tests are more complex than mode I (opening) due to the presence of a contact force between the two arms. This force is essential for the calculation of the energy release rate (ERR) and is closely linked to friction effects. A novel formulation is presented in this article to estimate the contact force analytically. Specifically, the contact force is derived within the context of the rigid, semi-rigid, and flexible joint models. The analytical solutions consider the case of a generally layered composite laminate with residual hygrothermal stresses and are used to evaluate the ERR. The new formulation is compared with numerical models created using the Virtual Crack Closure Technique (VCCT) and the Cohesive Zone Method (CZM) for a fiber–metal laminate. The results show that the new formulation provides nearly identical ERR predictions to those of the VCCT and CZM models. Additionally, it is demonstrated that the effect of friction on the ERR is less than 1%. [ABSTRACT FROM AUTHOR]

Currently, there is a lot of interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed using fiber-optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from the optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different Young's modulus values, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With the axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes. [ABSTRACT FROM AUTHOR]

Room temperature drop hammer impact and compression after impact (CAI) experiments were conducted on carbon fiber–epoxy resin (CF/EP) composites to investigate the variation in impact load and absorbed energy, as well as to determine the residual compressive strength of CF/EP composites following impact damage. Industrial CT scanning was employed to observe the damage morphology after both impact and compression, aiding in the study of impact-damage and compression-failure mechanisms. The results indicate that, under the impact load, the surface of a CF/EP composite exhibits evident cratering as the impact energy increases, while cracks form along the length direction on the back surface. The residual compressive strength exhibits an inverse relationship with the impact energy. Impact damage occurring at an energy lower than 45 J results in end crushing during the compression of CF/EP composites, whereas energy exceeding 45 J leads to the formation of long cracks spanning the entire width of the specimen, primarily distributed symmetrically along the center of the specimen. [ABSTRACT FROM AUTHOR]

This paper describes design, manufacture, and testing of a linerless composite vessel for liquid hydrogen, having 0.3 m diameter and 0.9 m length. The vessel consists of a composite cylinder manufactured by wet filament winding of thin-ply composite bands, bonded to titanium end caps produced by additive manufacturing. The aim was to demonstrate the linerless design concept with a thin-ply composite for the cylinder. The investigation is limited to the internal pressure vessel, while real cryogenic tanks also involve an outer vessel containing vacuum for thermal insulation. Thermal stresses dominate during normal operation (4 bar) and the layup was selected for equal hoop strains in the composite cylinder and end caps during filling with liquid hydrogen. Two vessels were tested in 20 cycles, by filling and emptying with liquid nitrogen to 4 bar, without signs of damage or leakage. Subsequently, one vessel was tested until burst at almost 30 bar. [ABSTRACT FROM AUTHOR]

This paper presents a mesoscale damage model for composite materials and its validation at the coupon level by predicting scaling effects in un-notched carbon-fiber reinforced polymer (CFRP) laminates. The proposed material model presents a revised longitudinal damage law that accounts for the effect of complex 3D stress states in the prediction of onset and broadening of longitudinal compressive failure mechanisms. To predict transverse failure mechanisms of unidirectional CFRPs, this model was then combined with a 3D frictional smeared crack model. The complete mesoscale damage model was implemented in ABAQUS®/Explicit. Intralaminar damage onset and propagation were predicted using solid elements, and in-situ properties were included using different material cards according to the position and effective thickness of the plies. Delamination was captured using cohesive elements. To validate the implemented damage model, the analysis of size effects in quasi-isotropic un-notched coupons under tensile and compressive loading was compared with the test data available in the literature. Two types of scaling were addressed: sublaminate-level scaling, obtained by the repetition of the sublaminate stacking sequence, and ply-level scaling, realized by changing the effective thickness of each ply block. Validation was successfully completed as the obtained results were in agreement with the experimental findings, having an acceptable deviation from the mean experimental values. [ABSTRACT FROM AUTHOR]

Resin matrix composites (RCs) have better thermal and chemical stability, so they are widely used in engineering fields. In this study, the aging process and mechanism of two different types of resin-based three-dimensional four-way braided composites (H15 and S15) under different hygrothermal aging conditions were studied. The effect of aging behavior on the mechanical properties of RCs was also studied. Three different aging conditions were studied: Case I, 40 °C Soak; Case II, 70 °C Soak; and Case III, 70 °C-85% relative humidity (RH). It was found that the hygroscopic behavior of RCs in the process of moisture-heat aging conforms to Fick's second law. Higher temperatures and humidity lead to higher water absorption. The equilibrium hygroscopic content of H15 was 1.46% (Case II), and that of S15 was 2.51% (Case II). FT-IR revealed the different hygroscopic mechanisms of H15 and S15 in terms of aging behavior. On the whole, the infiltration behavior of water molecules is mainly exhibited in the process of wet and thermal aging. At the same time, the effect of the aging process on resin matrices was observed using SEM. It was found that the aging process led to the formation of microchannels on the substrate surface of S15, and the formation of these channels was the main reason for the better moisture absorption and lower mechanical strength of S15. At the same time, this study further found that temperature and oxygen content are the core influences on post-aging strength. The LVI experiment also showed that the structural changes and deterioration effects occurring after aging reduced the strength of the studied material. [ABSTRACT FROM AUTHOR]

A weak circumferential resolution of defects in the corner part of engineering components brings great challenges to quantitative non-destructive testing. Especially for the corner of carbon fiber reinforced plastics (CFRP), the complex wave propagation behaviors caused by the elastic anisotropy, laminate structure, and curved surface make the information of defects hard to be distinguished, which finally results in a poor imaging resolution. The surface adaptive ultrasonic (SAUL) method for CFRP corner is investigated, and an improved strategy, focusing in receiving (FiR) of SAUL signals is proposed here. With an isotropic plexiglass as a comparison, the effectiveness of FiR is verified by finite element simulations and experiments. The elastic properties of CFRP corner are accurately characterized and a finite element model is established. On this basis, the wave propagation behavior in the corner is studied, and the influence of the water distance h on the maximum amplitude (MAD) and signal-to-noise ratio (SNR) at the defect is analyzed. The results show that the structural noise can be eliminated, and the imaging quality and SNR can be improved by optimizing the h. After FiR, the maximum increase of defect amplitude is about 9.5 dB and 13.2 dB for plexiglass and CFRP, respectively. Meanwhile, the maximum relative error in length is reduced by 16.7% in plexiglass, and by 13.4% for the 3-mm delamination in CFRP. The strategy would be promising to improve the detection quality of the corner in curved components. [ABSTRACT FROM AUTHOR]

The use of thin-ply composite materials has rapidly increased due to their tailorable mechanical properties and design flexibility. Considering an adhesively bonded composite joint, peel stress stands out as a key contributor leading to failure among other primary stress factors. Therefore, the reinforcement of carbon fiber-reinforced polymer (CFRP) laminates throughout the thickness could be considered as an approach to improve the joint strength. Using thin plies locally between the conventional CFRP layers in a laminate can enhance the strength, as the sudden change in stiffness means that the load transfer is not monotonous. Consequently, the following study examined the effect of altering thin plies gradually throughout the thickness on the behaviour of the CFRP laminates when subjected to transverse tensile loading. To achieve this goal, the CFRP laminates were gradually modified by using different commercially accessible prepreg thin plies, leading to an improved overall structural performance by reducing stress concentrations. Besides conducting an experimental study, a numerical assessment was also carried out utilizing Abaqus software with a Representative Volume Element (RVE) at the micro scale. The comparison of reference configurations, which involved various thin plies with different thicknesses and traditional CFRP laminates, with the suggested gradual configuration, demonstrated a notable enhancement in both strength and material cost. Furthermore, the proposed RVE model showed promising capability in accurately forecasting the strength of fabricated laminates. [ABSTRACT FROM AUTHOR]

The investigation of the in-plane shear behavior of prepreg is crucial for understanding the generation of wrinkles of preforms in advanced composite manufacturing processes, such as automated fiber placement and thermoforming. Despite this significance, there is currently no standardized test method for characterizing uncured unidirectional (UD) prepreg. This paper introduces a ±45° off-axis tensile test designed to assess the in-plane shear behavior of UD carbon fiber-reinforced epoxy prepreg (CF/epoxy). Digital image correlation (DIC) was employed to quantitatively track the strains in three dimensions and the shear angle evolution during the stretching process. The influences of the temperature and stretching rate on the in-plane shear behavior of the prepreg were further investigated. The results reveal that four shear characteristic zones and wrinkling behaviors are clearly distinguished. The actual in-plane shear angle is significantly lower than the theoretical value due to fiber constraints from both the in-plane and out-of-plane aspects. When the off-axis tensile displacement (d) is less than 15.6 mm, the ±45° specimens primarily exhibit macroscale in-plane shear behavior, induced by interlaminar interface shear between the +45° ply and −45° ply at the mesoscale. The shear angle increases linearly with the d. However, when d > 15.6 mm, fiber squeezing and wrinkling begin to occur. When d > 29 mm, the in-plane shear disappears in the completely sheared zone (A). The reduction in the resin viscosity of the CF/epoxy prepreg caused by increased temperature is identified as the primary factor in lowering the in-plane shear force resistance, followed by the effect of the increasing resin curing degree. Higher shear rates can lead to a substantial increase in shear forces, eventually causing cracking failure in the prepreg. The findings demonstrate the feasibility of the test method for predicting and extracting uncured prepreg in-plane shear behaviors and the strain-rate and temperature dependency of the material response. [ABSTRACT FROM AUTHOR]

This research aims to examine the tensile strength of a hybrid composite laminate reinforced by thin-plies when used as an adherend in bonded single lap joints subjected to high-rate and impact loading. Two different composites, namely Texipreg HS 160 T700 and NTPT-TP415, are employed as the conventional and thin-ply composites, respectively. The study considers three configurations: a conventional composite, a thin-ply, and a hybrid single lap joint. Numerical models of the configurations are developed to provide insight into failure mechanisms and the initiation of damage. The results indicate a significant increase in tensile strength for the hybrid joints over the conventional and thin-ply joints, due to the mitigation of stress concentrations. Overall, this study demonstrates the potential of hybrid laminates for improving the performance of composite joints under highrate loading and impact conditions. [ABSTRACT FROM AUTHOR]

Carbon fiber reinforced composites (CFRP) are susceptible to hidden damage from low velocity external impacts during their service life. To ensure the proper monitoring of the state of the composites, it is crucial to predict the location of an impact event. In this paper, fiber Bragg grating (FBG) sensors are affixed to the surface of a carbon fiber composite tube, and an optical sensing interrogator is used to capture the central wavelength shift of the FBG sensors due to low-velocity impacts. A discrete wavelet transform is used for noise reduction in the response signals. Then, the differences in the captured response signals of the FBG sensors at different locations of the impact were analyzed. Moreover, two methods were implemented to predict the location of low-velocity impacts, according to the differences in the captured response signals. The BP neural network-based method utilized three data sets to train the neural network, resulting in an average localization error of 20.68 mm. In contrast, the method based on error outliers selected a specific data set as the reference dataset, achieving an average localization error of 13.98 mm. The comparison of the predicted results shows that the latter approach has a higher predictive accuracy and does not require a significant amount of data. [ABSTRACT FROM AUTHOR]

On-site and real-time non-destructive measurement of elastic constants for materials of a component in a in-service structure is a challenge due to structural complexities, such as ambiguous boundary, variable thickness, nonuniform material properties. This work develops for the first time a method that uses ultrasound echo groups and artificial neural network (ANN) for reliable on-site real-time identification of material parameters. The use of echo groups allows the use of lower frequencies, and hence more accommodative to structural complexity. To train the ANNs, a numerical model is established that is capable of computing the waveform of ultrasonic echo groups for any given set of material properties of a given structure. The waveform of an ultrasonic echo groups at an interest location on the surface the structure with material parameters varying in a predefined range are then computed using the numerical model. This results in a set of dataset for training the ANN model. Once the ANN is trained, the material parameters can be identified simultaneously using the actual measured echo waveform as input to the ANN. Intensive tests have been conducted both numerically and experimentally to evaluate the effectiveness and accuracy of the currently proposed method. The results show that the maximum identification error of numerical example is less than 2%, and the maximum identification error of experimental test is less than 7%. Compared with currently prevailing methods and equipment, the proposefy the density and thickness, in addition to the elastic constants. Moreover, the reliability and accuracy of inverse prediction is significantly improved. Thus, it has broad applications and enables real-time field measurements, which has not been fulfilled by any other available methods or equipment. [ABSTRACT FROM AUTHOR]

In recent years, the field of mandibular reconstruction has made great strides in terms of hardware innovations and their clinical applications. There has been considerable interest in using computer-aided design, finite element modelling, and additive manufacturing techniques to build patient-specific surgical implants. Moreover, lattice implants can mimic mandibular bone's mechanical and structural properties. This article reviews current approaches for mandibular reconstruction, their applications, and their drawbacks. Then, we discuss the potential of mandibular devices with lattice structures, their development and applications, and the challenges for their use in clinical settings. [ABSTRACT FROM AUTHOR]

Composite materials are of increasing interest in aircraft and spacecraft structures, and carbon fiber reinforced polymers (CFRP) have emerged as materials meeting quality standards for structural applications in the aircraft industry. Despite their high mechanical properties, CFRPs are associated with high production costs. Building on recent research by the authors, this paper investigates the use of ply-level hybridization to reduce manufacturing costs while maintaining the mechanical performance of the manufactured material. Focusing on the causes of nonlinear response under off-axis tensile loading, the paper involves cyclic load-unload (LU) tensile tests conducted at off-axis angles of 15°, 30°, and 45° to predict mechanical characteristics and damage evolution. Residual strains are directly extracted from load-unload stress-strain responses. Three distinct methods for estimating cycle modulus are employed and compared for damage variable formulation. The research findings reveal dependencies of both the damage variable and residual strains on the off-axis angle. Furthermore, the method used to assess the modulus during cycling loading significantly influences the damage variable estimation. Encouragingly, the hybrid laminates exhibit reduced internal damage and matrix plasticity compared to reference counterparts, indicating a positive effect on the mechanical performances of hybridized CFRPs in addition to the cost reduction. [ABSTRACT FROM AUTHOR]

Tailoring vacancies is a feasible way to improve the mechanical properties of ceramics. However, high concentrations of vacancies usually compromise the strength (or hardness). We show that a high elasticity and flexural strength could be achieved simultaneously using a nitride superlattice architecture with disordered anion vacancies up to 50%. Enhanced mechanical properties primarily result from a distinctive deformation mechanism in superlattice ceramics, i.e., unit-cell disturbances. Such a disturbance substantially relieves local high-stress concentration, thus enhancing deformability. No dislocation activity involved also rationalizes its high strength. The work renders a unique understanding of the deformation and strengthening/toughening mechanism in nitride ceramics. Ceramics are very brittle and hard to be plastically deformed. Here, the authors report a unit-cell scale disturbance mechanism to improve the deformation ability of ceramics and ultimately achieve large mechanical property enhancement. [ABSTRACT FROM AUTHOR]

The identification of elastic constants of carbon fiber reinforced plastic structures is vital for understanding their deformation characteristics and evaluating molding quality. In contrast to conventional mechanical testing methods, this study devised a combined experimental–numerical method that can identify the detailed spatial elastic constant distribution of a structure based on its natural frequencies, which were measured by modal tests and predicted using finite element (FE) simulations. A genetic algorithm (GA)-based parametric optimization process was then applied to iteratively update the moduli settings in the FE model, aiming to minimize the discrepancy between the simulated and experimentally measured natural frequencies of the structure. The final converged moduli set in the FE model comprised the identified modulus distributions of the structure. In addition, several model simplification methods were discussed to simplify the complexity of the parameter optimization. Design of experiment (DOE) method was found to be effective in screening the main design variables. Moreover, multiple calculation strategies were evaluated to enhance the accuracy of the identification process. A novel calculation strategy that integrated multiple FE models was demonstrated to achieve satisfactory accuracy for the evaluated structures. To demonstrate and validate the proposed approach, chopped carbon fiber tape-reinforced thermoplastic (CTT) plate and hat-shaped structures were utilized as examples. [ABSTRACT FROM AUTHOR]

The porous structure can reduce the elastic modulus of a dental implant and better approximate the elastic characteristics of the material to the alveolar bone. Therefore, it has the potential to alleviate bone stress shielding around the implant. However, natural bone is heterogeneous, and, thus, introducing a porous structure may produce pathological bone stress. Herein, we designed a porous implant with axial gradient variation in porosity to alleviate stress shielding in the cancellous bone while controlling the peak stress value in the cortical bone margin region. The biomechanical distribution characteristics of axial gradient porous implants were studied using a finite element method. The analysis showed that a porous implant with an axial gradient variation in porosity ranging from 55% to 75% was the best structure. Under vertical and oblique loads, the proportion of the area with a stress value within the optimal stress interval at the bone–implant interface (BII) was 40.34% and 34.57%, respectively, which was 99% and 65% higher compared with that of the non-porous implant in the control group. Moreover, the maximum equivalent stress value in the implant with this pore parameter was 64.4 MPa, which was less than 1/7 of its theoretical yield strength. Axial gradient porous implants meet the strength requirements for bone implant applications. They can alleviate stress shielding in cancellous bone without increasing the stress concentration in the cortical bone margin, thereby optimizing the stress distribution pattern at the BII. [ABSTRACT FROM AUTHOR]