Search

This paper presents an experimental study on the physicochemical properties of rice oil, peanut oil, corn oil and Kraft paper immersed in these oils in the presence of antioxidants (butylated hydroxytoluene, tertiary butyl hydroquinone and Naugalube¯ 750). The experiments are performed on new and aged conditions. Ageing of oils is carried at 115 °C for 96 hours while Kraft paper is aged in oils at 130 °C for 164 hours. Both closed and open cup methods are used for ageing. The results show that ageing insignificantly affects the breakdown voltage, but markedly increases the acid number and the viscosity of the vegetable oils. The combination of tertiary butyl hydroquinone and either butylated hydroxytoluene or Naugalube¯ 750 slightly increases the breakdown voltage, but significantly raises the oxidation stability of the vegetable oils. This results in a reduction in the viscosity and the acid number of the vegetable oils. Moisture significantly affects the breakdown voltage of both vegetable and mineral oil. High moisture content results in low breakdown voltage. The results also show that ageing insignificantly affects the breakdown voltage, but markedly decreases the tensile strength of oil-impregnated paper. Although the presence of antioxidants does not increase the breakdown voltage of aged paper, these additives slow down the ageing process. This results in an increase in tensile strength of the paper. [ABSTRACT FROM AUTHOR]

The problem of sulfur corrosion has seriously affected the safe and stable operation of the power transformers. Currently, adding passivators into the transformer oil is the most effective method to suppress the problem. However, no explicit provisions have been made for the optimum concentration of the specific passivators. In this paper, the transformer oils with different corrosive sulfurs and different aging degrees were used to study the protective performance of three different passivators. By comparing the copper surface, the optimum concentrations for each passivators were acquired. Moreover, by testing the breakdown voltage, dielectric loss factor, volume resistivity, and moisture content of the insulating oil after adding passivators with the optimal concentration, the effect of three passivators on the oil quality was obtained. Results show that the three passivators have different protective performance on different types of corrosive sulfurs. Irgamet 39 has a better protective effect at lower concentrations than the other two. The protective effect of all three passivators on dodecyl mercaptan is poor, and a new type of passivator capable of protecting against dodecyl mercaptan needs to be developed. Moreover, the three passivators have different protection performance on the transformer oils with different aging degrees. The protective performance is poor especially for the oils with longer running years or passivators with lower concentrations. Among the three passivators, Irgamet 39 had the smallest impact on the oil quality, followed by T571 and then TTA. The above research can provide some references for guiding the passivator addition in actual projects and preventing the occurrence of sulfur corrosion failures.

This paper presents a thorough review of transmitarray devices particularly aiming antenna beamsteering, gathering some of the most relevant solutions published by the scientific community in the field. First, the background for realizing 1-D and 2-D antenna beamsteering with a transmitarray is introduced. Subsequently, several examples of unit-cells for transmitarray implementation and complete transmitarray designs presented in the literature are outlined. Each solution is analyzed in detail, identifying the nature of its layout, e.g., based on microstrip patches, frequency selective surfaces (FSS), or metamaterials (MMs), and the method employed to enable electronic reconfigurability, e.g., p-i-n diodes, varactor diodes, or microelectromechanical systems (MEMS). In addition, some models with the capability of controlling the wavefront polarization modes are also included herein since these are the base of hybrid transmitarrays, i.e., transmitarray with both electronic beamsteering and polarization control. Finally, all the models are compared against each other in order to highlight their benefits and limitations, summarizing their main characteristics, such as the frequency of operation and bandwidth, insertion loss, physical dimensions, and maximum beamsteering range, when available.

This paper extends our previous work on silver-enhancement based self-assembling structures for designing reliable, self-powered biosensors with forward error correcting (FEC) capability. At the core of the proposed approach is the integration of paper-based microfluidics with quick response (QR) codes that can be optically scanned using a smart-phone. The scanned information is first decoded to obtain the location of a web-server which further processes the self-assembled QR image to determine the concentration of target analytes. The integration substrate for the proposed FEC biosensor is polyethylene and the patterning of the QR code on the substrate has been achieved using a combination of low-cost ink-jet printing and a regular ballpoint dispensing pen. A paper-based microfluidics channel has been integrated underneath the substrate for acquiring, mixing and flowing the sample to areas on the substrate where different parts of the code can self-assemble in presence of immobilized gold nanorods. In this paper we demonstrate the proof-of-concept detection using prototypes of QR encoded FEC biosensors.

This paper presents a wireless, self-powered, affinity-based biosensor based on the integration of paper-based microfluidics with our previously reported method for self-assembling radio-frequency (RF) antennas. At the core of the proposed approach is a silver-enhancement technique that grows portions of a RF antenna in regions where target antigens hybridize with target specific affinity probes. The hybridization regions are defined by a network of nitrocellulose based microfluidic channels which implement a self-powered approach to sample the reagent and control its flow and mixing. The integration substrate for the biosensor has been constructed using polyethylene and the patterning of the antenna on the substrate has been achieved using a low-cost ink-jet printing technique. The substrate has been integrated with passive radio-frequency identification (RFID) tags to demonstrate that the resulting sensor-tag can be used for continuous monitoring in a food supply-chain where direct measurement of analytes is typically considered to be impractical. We validate the proof-of-concept operation of the proposed sensor-tag using IgG as a model analyte and using a 915 MHz Ultra-high-frequency (UHF) RFID tagging technology.

This paper investigates the behavior of interface charges between oil and oil immersed paper insulations in unaged and aged samples. Combined accelerated thermal and electrical aging experiments of oil immersed paper insulations are conducted to obtain aged oil and aged paper samples. The interface charges between oil and paper samples with different aging status are measured with the Pulsed Electro-acoustic (PEA) method. Zeta potentials in samples with different aging status are determined. It is shown that the amount of interface charge increases with the aging duration, and does not follow the prediction of Maxwell-Wagner-Sillars (MWS) law. This is explained in terms of the increase of the interface charge barrier due to the effect of electric double layer. It is proposed that interface charge may act as an optional characterization parameter for the assessment of oil immersed paper insulations. [ABSTRACT FROM AUTHOR]

The application of vibration-based condition monitoring methods to power transformers has shown the potential for detecting mechanical transformer failures. The ageing of winding insulation paper, which is a common problem in long-serving power transformers, affects both the electrical and mechanical strength of the windings. This paper is concerned with the vibration features of winding disks with aged insulation paper. The vibration characteristics of single-layer winding disks wrapped with insulation paper are investigated. By examining the vibration frequency responses of winding disks with different degrees of ageing of insulation paper, the effects of aged paper on the vibration behaviors of winding disks are demonstrated. The experimental results show that changes in the vibration responses of winding disks can be related to the ageing of insulation paper, and thus it is possible to detect this failure mode in a power transformer using a vibration-based method. A qualitative explanation for these changes is presented, using the degradation of the mechanical strength of the insulation paper. [ABSTRACT FROM AUTHOR]

The recipients of the 2020 NSREC Outstanding Conference Paper Award are George N. Tzintzarov, Adrian Ildefonso, Jeffrey W. Teng, Milad Frounchi, Albert Djikeng, Prahlad Iyengar, Patrick S. Goley, Ani Khachatrian, Joel M. Hales, Ryan Bahr, Stephen Buchner, Dale McMorrow, and John D. Cressler for their paper entitled “Optical Single-Event Transients Induced in Integrated Silicon-Photonic Waveguides by Two-Photon Absorption.” [ABSTRACT FROM AUTHOR]

The long-term operation of dry-type transformer bushings at high temperatures can impact the performance of their primary insulation material. This article presents an experimental study of the effect of thermal aging time on electrical treeing in the epoxy resin-impregnated paper. The experimental results show that the electrical treeing pattern along the middle path of the electric field and the interlayer creepage along the average direction of the electric field are closely related to the aging time. Under the effect of thermal aging at 150 °C, the tree-starting voltage of epoxy resin-impregnated paper tends to increase and decrease as the aging time increases. An analysis and discussion of the test results in conjunction with scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) tests suggest that the destruction of the cross-linked network of the epoxy resin-impregnated paper at 150 °C is a fundamental reason for the significant decrease in the material’s tree-starting voltage and the change in electrical treeing morphology and interlayer creepage. Long-term operation at high temperatures can seriously impact the primary insulation performance of dry-type transformer bushings and requires attention. [ABSTRACT FROM AUTHOR]

We report on investigation of the mechanical properties of paper electronics (printed and made out of paper). One key objective of such paper electronics is to achieve ultraflexibility. Therefore, it is important to understand electrical functionality and reliability of paper electronics under various physical (mechanical) deformations. Here, we show the general mechanical properties of the cellulose paper used and its electrical behavior under applied strain, tackling the main effects that need to be identified when building paper-based systems, from product performance and stability perspective. An overview of the stress–strain behavior of silver ink on paper is discussed, and then, we tackle a more specific analysis of the performance variations of paper sensors made with recyclable household materials when exposed to various mechanical conditions of tensile and compressive bending. This paper is important for developing stable wearable sensors for incorporation into Internet of Everything applications. [ABSTRACT FROM PUBLISHER]

Introduction: The electrocardiogram (ECG) plays an important role in the diagnosis of heart diseases. However, most patterns of diseases are based on old datasets and stepwise algorithms that provide limited accuracy. Improving diagnostic accuracy of the ECG can be done by applying machine learning algorithms. This requires taking existing scanned or printed ECGs of old cohorts and transforming the ECG signal to the raw digital (time (milliseconds), voltage (millivolts)) form. Objectives: We present a MATLAB-based tool and algorithm that converts a printed or scanned format of the ECG into a digitized ECG signal. Methods: 30 ECG scanned curves are utilized in our study. An image processing method is first implemented for detecting the ECG regions of interest and extracting the ECG signals. It is followed by serial steps that digitize and validate the results. Results: The validation demonstrates very high correlation values of several standard ECG parameters: PR interval 0.984 +/-0.021 (p-value

The Editorial Board of the IEEE Open Access Journal of Power and Energy (OAJPE) would like to recognize the following best papers selected from all papers published between October 2018 and September 2021 in OAJPE and its preceding journal, IEEE Power and Energy Technology Systems Journal (PETS-J).

The generation and distribution of furfural are significantly affected by moisture content in the insulating paper. However, the diffusion mechanism of furfural under moisture effect is not clear, hence, this study investigates the effect of moisture on the diffusion characteristics of furfural by combining macro experiment and micro molecular dynamics simulation. The simulation results demonstrate that the increased moisture content in paper accelerates the diffusion of furfural from paper to oil, which is also proved by the experimental data. Then, the results of interaction energy analysis indicate that the increase of moisture enhances the van der Waals force between oil and furfural. The present findings are expected to improve the theoretical level of furfural analysis, which will facilitate the aging evaluation of the transformer insulating paper based on furfural. [ABSTRACT FROM AUTHOR]

The semantic link network is a semantics modeling method for effective information services. This paper proposes a new text summarization approach that extracts semantic link network from scientific paper consisting of language units of different granularities as nodes and semantic links between the nodes, and then ranks the nodes to select Top-k sentences to compose summary. A set of assumptions for reinforcing representative nodes is set to reflect the core of paper. Then, semantic link networks with different types of node and links are constructed with different combinations of the assumptions. Finally, an iterative ranking algorithm is designed for calculating the weight vectors of the nodes in a converged iteration process. The iteration approximately approaches a stable weight vector of sentence nodes, which is ranked to select Top-k high-rank nodes for composing summary. We designed six types of ranking models on semantic link networks for evaluation. Both objective assessment and intuitive assessment show that ranking semantic link network of language units can significantly help identify the representative sentences. This paper not only provides a new approach to summarizing text based on the extraction of semantic links from text but also verifies the effectiveness of adopting the semantic link network in rendering the core of text. The proposed approach can be applied to implementing other summarization applications such as generating an extended abstract, the mind map, and the bulletin points for making the slides of a given paper. It can be easily extended by incorporating more semantic links to improve text summarization and other information services.

In the last decade, much effort has been invested in using methanol as an oil-soluble chemical marker for assessing the condition of insulating paper. The use of this marker as paper life index presents many advantages particularly with new transformers insulated with thermally upgraded papers. However, until now, no interpretation model has been available for its extensive use by the transformer community. In this paper, a methanol-based interpretation model is presented for the first time using postmortem paper analysis on core-type transformers. This model allows the evaluation of the average degree of polymerization of a transformer's cellulose winding. Furthermore, threshold values based on the methanol concentration are given using this approach. Finally, model validation was performed on a limited number of papers taken from transformers being assessed in the repair shop. [ABSTRACT FROM PUBLISHER]

For extra-high-voltage high-temperature superconducting (HTS) cables, not only high electrical insulation performance but also low dielectric loss is required. Therefore, we focus on a porous synthetic paper with lower dielectric loss, e.g., Tyvek polyethylene nonwoven fabric, than that of polypropylene laminated paper (PPLP), which has been used for a conventional HTS cable insulation system. In this paper, we compare partial discharge inception characteristics for different liquid nitrogen/synthetic paper composite insulation systems. The partial discharge inception electric field strength in the composite insulation system depends on the electric field strength in the porous area of synthetic paper. [ABSTRACT FROM AUTHOR]

This paper presents an investigation of the underlying mechanism behind the interface charge barrier between oil and oil immersed paper. Two types of oils and two types of cellulose papers are selected in the study. The interface charges of the samples are measured by the pulsed electro-acoustic (PEA) method and the zeta potentials of different oil-paper combinations are also measured. The results show that the amount of interface charge changes with the type of oils and papers, and is much larger than the Maxwell-Wagner-Sillars (MWS) polarization charge. The difference in the amount of interface charges cannot be attributed to the difference in the conductivity and permittivity of the materials. It is suggested that the barrier for charge transport across the interface, which is formed due to the electric double layer, should be taken into consideration to explain the interface charge behavior in oil-paper insulation. [ABSTRACT FROM AUTHOR]

Background: Although some have noted that combining technical and marketing content is precarious, technical communication professionals are increasingly involved in content marketing, which includes the creation of white papers. Literature review: The little existing literature on white papers provides conflicting guidance about managing the combination of technical and marketing content. Both soft-sell and hard-sell marketing approaches have been recommended. One source of such inconsistent guidance may be the lack of agreement about definitions. Research on print advertisements has described hard and soft selling as multidimensional rather than binary aspects of persuasive appeals. Research question: Which dimensions of hard- and soft-sell appeals are predominant in white papers? Research methodology: To complete our descriptive study, we collected a corpus of documents labeled as white papers in TechRepublic, and then selected and trained three raters to complete a series of judgments about dimensions of persuasive appeals in the corpus. We aggregated those ratings, calculating the mean and standard deviation for the dimensions to describe their distribution across the corpus. Results/discussion: Overall, hard-sell dimensions were more prevalent than soft-sell dimensions. However, the soft-sell category of “implicitness” was also dominant. Conclusion: Our results demonstrate the value of treating hard and soft selling as multidimensional, complementary, and combinatory marketing appeals that allow, for example, a single white paper to be both “subjective” (soft sell), and “precise” (hard sell), or both “creative” (soft sell) and “informative” (hard sell). [ABSTRACT FROM AUTHOR]

The mechanical performance of two commercial papers used as solid insulation in power transformers, namely standard Kraft and a thermally upgraded Kraft paper, were studied during accelerated aging in Luminol oil at 170 ?C. The results show a relationship between the degree of polymerization and the mechanical properties measured by tensile testing. A linear relationship was found between the mechanical properties of paper, the tensile index (Tidx), and the concentration of methanol present in the oil. The methanol chemical marker has been proven to be an accurate assessment tool for the aging of cellulosic paper. The results show a promising tool for correlating the methanol concentration in oil, as an indirect indicator, with the mechanical performance of the paper. This approach can be used to monitor the real state of the cellulose chains in the power transformer insulation paper. [ABSTRACT FROM AUTHOR]

The article titled "Call for Papers: IEEE ETHICS-2025" discusses the theme of the 2025 IEEE ETHICS conference, which is "Emerging Technologies, Ethics, and Social Justice." The conference aims to explore various topics related to the ethical and social implications of emerging technologies, such as automation, AI ethics, social innovation, and the future of work. It also highlights the connection between emerging technologies and UN Sustainable Development Goals, as well as the importance of teaching AI ethics. The article provides information on the submission deadline for papers and poster abstracts. [Extracted from the article]

Furfural content in oil is widely accepted as an effective parameter to mirror aging of insulation paper. However, pressboards are also abundant in transformers, which are always neglected in furfural analysis. Different masses of insulation paper and pressboard produce different amounts of furfural during the aging process. Thus, the furfural content in oil may differ in systems with different oil-paper-pressboard mass ratios. To address this problem, accelerated thermal aging experiments and furfural equilibrium experiments with different oil-paper-pressboard mass ratio systems were conducted under laboratory conditions. Furfural contents in oil, paper, and pressboard were measured. In a simplified oil-paper system, the furfural content in oil differs in systems with different oil-paper mass ratios. Further analysis shows the furfural amount produced by 1 g insulation paper is the same with good repeatability in groups with different mass ratios. Different oil-paper mass ratios change the distribution coefficient of furfural between oil and paper, and an increase in the mass of insulation paper leads to more furfural remaining in the insulation paper. The pressboards in field transformers produce little furfural during the aging process, but absorb part of the furfural from oil, which decreases the furfural content in oil. Therefore, more pressboard in an oil-paper-pressboard system indicates lower furfural content in oil. An increase in insulation paper in the oil-paper-pressboard system causes a decrease in the effect of pressboard on furfural content in oil. [ABSTRACT FROM AUTHOR]

Recent studies have reported that thermal aging of insulation paper affects its moisture absorption property, which can affect moisture equilibrium in oil-paper insulation. In engineering practice, Fessler's model is one of the most widely used methods to estimate the moisture content of paper through measurement of moisture content of oil. However, this model lacks consideration of the thermal aging effect on equilibrium moisture. This study comprehensively investigated the effect of thermal aging on moisture equilibrium in oil-paper insulation. Based on the accelerated ageing and moisture measurements, the equilibrium moisture content of insulation paper with different aging and temperatures were obtained. The effects of aging condition and the temperature on equilibrium moisture are discussed and Fessler's model was modified accordingly. The results show that: 1) the decreasing of specific surface area is the dominant factor that affects the moisture equilibrium in oil-paper insulation, which is caused by thermal aging; 2) the modified Fessler model is reasonable and suitable to estimate the equilibrium moisture content of insulation paper with different aging. [ABSTRACT FROM AUTHOR]

High-frequency (HF) oil-immersed transformers with small size and light weight have been paid wide attention by researchers. Its oil–paper insulation frequently withstands HF over-voltages at frequencies of several kilohertz and above, resulting in the too early failure of oil–paper insulation. In order to investigate the effect of HF on oil–paper insulation, this article investigates the partial discharge (PD) characteristics of oil–paper insulation under HF stress. The experimental results show that a frequency-induced inflection point is existed near 10 kHz and the PD parameters of HF voltages is much higher than that ac voltages. Besides, the theoretical mechanism is expounded to interpret and understand the formation process of frequency-induced inflection points more easily. It can be found that the change in frequency causes the change in the charge decay time constant and the residual charge on the insulating surface, resulting in the formation of the frequency-induced inflection point at HF. These results might contribute to determine the characteristics of PDs between HF voltages and ac voltages. It can provide references for the research and production of HF transformers. [ABSTRACT FROM AUTHOR]

Vegetal oils are considered a suitable substitute for mineral oil that is widely used in power transformers as insulation and cooling medium. Due to the fact that more and more power transformers containing this alternative insulating fluid are being constructed a mathematical ageing models is needed to help predict transformer failures. The continued performance of power transformers depends on the condition of its paper insulation mainly. In this sense, this paper analyses Kraft paper degradation through the loss of its mechanical strength. Accelerated thermal ageing test of the paper in two different vegetal oils were carried out at three temperatures during diverse periods of time, in order to obtain information on the kinetics of the ageing degradation of the paper. The evolution of the mechanical properties of paper failure are analysed as a function of temperature and ageing time. In addition, the results obtained are compared with the traditional method of degradation analysis, based on the measurement of the degree of polymerisation. [ABSTRACT FROM AUTHOR]

The life expectancy of a transformer is closely related to the ageing state of its paper insulation. This paper presents novel markers for ageing characterization of paper insulation in oil-filled transformers based on the dispersion staining colors of cellulose fibres. Accelerated thermal ageing experiments were performed for oil-paper specimens at 120 and 130 °C to obtain aged oil-paper samples of different ageing degrees. The average degree of polymerization (DP), crystallinity index, and refractive index of insulation paper were measured; the experimental results show that an increase in refractive index of insulation paper was observed with the increase of ageing degree. Meanwhile, the dispersion staining colors of cellulose fibres in oil were observed using dispersion staining method; the experimental results show that the refractive index of cellulose fibres detached from insulation paper increases with the increment of ageing degree of insulation paper. Finally, two ageing markers—that is, the primary color ratio-based ratio of blue to red and the primary color ratio-based Mahalanobis distance were presented. Their relationship with DP and ageing time of insulation paper were obtained, and were compared with the corresponding relationship with 2-furaldehyde (2-FAL) and carbon oxides. The proposed ageing markers demonstrate an advantage over 2-FAL and carbon oxides and show potential in ageing state evaluation and residual life prediction of paper insulation in transformers. [ABSTRACT FROM AUTHOR]

This paper describes a flow control of the dye in the paper mill with the quasi-Z-source indirect matrix converter (QZSIMC) fed induction motor drive. More than a decade the voltage-source inverter (VSI) and current-source inverter (CSI) have been used to control the speed of the induction motor, which in turns controls the flow of dye. Recently, the matrix converter (MC) has been an excellent competitor for the VSI or CSI for its compactness. The voltage transfer ratio of the VSI, CSI, and MC has been limited to 0.866. Thus, the efficiency of these converters is less. To improve the voltage transfer ratio the quasi-Z-source network (QZSN) is to be used between voltage source and indirect MC (IMC). The modification in the shoot-through duty ratio of the QZSN varies the voltage transfer ratio greater than 0.866. Different voltage transfer ratios are needed for different voltage sag conditions. For a variation of the duty ratio of the QZSN, the fuzzy logic controller has been presented. To control the IMC vector control with space vector modulation has been presented. This paper proposes the implementation of QZSIMC adjustable speed drive for the flow control of dye in paper mill during different voltage sag conditions. A 4-kW prototype has been built and the effectiveness of the proposed system is verified with simulation results and experimental setup. Simulation is done in MATLAB, Simulink platform. Experimental setup is done with the aid of a TMS320F2812 (Texas Instrument) processor. The experimental results validate the maintenance of the speed of an induction motor at the set condition, thus controlling the perfect flow of dye in paper manufacturing technology. [ABSTRACT FROM AUTHOR]

This Special Section is devoted to the research and development activities of all areas of flexible electronics science and technology. We have a selected number of high impact technical papers presented at the first IEEE International Flexible Electronics Technology Conference (IFETC) in 2018 for publication in J-EDS. The first IFETC was held in Ottawa, Ontario, Canada from the 7th to 9th August, 2018. The conference was financially sponsored by the IEEE Council on RFID, and technically sponsored by the National Research Council Canada, IEEE Electron Device Society, and the IEEE Instrumentation and Measurement Society. The conference was dedicated to the advances in flexible electronics in all areas of science and technology, and provided an opportunity for scientists, researchers, engineers, developers, and users in the field to share, discuss, and witness new concepts and ideas. A wide spectrum of academic research results was presented, with potential applications in current industrial technology and new application driven domains.

The publication of the 2020 Special Section of Invited Papers on Emerging Topics in the Power and Energy Society (PES) received broad interest from diverse readers of the PES community. We continued to publish the special section for another year. After a rigorous peer-review process, a total of 13 papers [A1]–[A13] were accepted for publication in this invited section of the IEEE Open Access Journal of Power and Energy (OAJPE) in 2021.

The space charge effect of transformer insulating paper will distort its internal electric field, and its space charge effect will be more prominent under extremely complex working conditions. At present, the micromechanism of charge transport and electric field distortion characteristics of paperboard are not clear under complex working conditions. So in this article, based on the bipolar carrier transport (BCT) model and the dynamic carrier balance model, the effects of high temperature, aging degree, moisture content, and bent degree on charges accumulation in paperboard are studied under dc high voltage by numerical simulation and the measured data needed for simulation. The results show that the higher temperature strengthens the carrier migration, deepens the injection depth of the charge, and aggravates the distortion of electric field intensity in paperboard. The more extended the aging time of paperboard, the greater the internal trap density and the deeper the trap depth, which lead to charges migration difficultly. Increasing water content in the paperboard will accelerate space charges to reach a steady state, while further increasing it will slow down this process, which is related to the shallow trap getting deeper. When the critical part of paperboard is extruded, many traps are introduced, resulting in charges accumulation seriously. The research results can reference the design of paperboard and the maintenance of transformer insulation system. [ABSTRACT FROM AUTHOR]

A growing body of evidence suggests that the ethanol dissolved in the oil can be used as an indicator to effectively monitor the aging behavior of insulating paper. In this study, thermal aging experiments are performed on oil-paper systems with different initial moisture contents and aging temperatures, and then a gas chromatography-mass spectrometer equipped with an automatic headspace sampler is used to test the ethanol contents of the oil samples. The variations and correlations of ethanol contents with temperature, moisture and aging degree are analyzed. The experimental results show that the ethanol contents in oil had a strong correlation with temperature, and is also affected by the cellulose hydrolysis. In addition, a preliminary lifespan assessment of the oil-paper systems under laboratory conditions is conducted by establishing the relationship between ethanol and the degree of polymerization. Then, the time-temperature superposition method is applied to the relationship, and a lifespan model with any temperature is determined according to the ethanol kinetic equation. Based on the model, further observation of the fitting parameters in the case of the two moisture contents (0.8%, 2.3%), the goodness of fit reached higher values of 0.961 and 0.973, respectively. The results of this promising model can help us to a better understanding of ethanol indicator to condition assessment for the transformer paper insulation. [ABSTRACT FROM AUTHOR]

It is well established that copper sulfide is formed due to reaction of sulfur with copper conductors in transformers and reactors. However, there is very little experimental evidence to demonstrate copper sulfide diffusion into bulk of paper. Diffusion experiments have been carried out on three samples of kraft paper having different thickness. Positron Annihilation Lifetime Spectroscopy has been used to investigate the possibilities of copper sulfide diffusion into bulk of paper. This study has demonstrated that copper sulfide can diffuse into the bulk of paper leading to either increase or decrease in free volume of paper. The reasons for changes in free volume of paper due to copper sulfide deposits are explained. The consequences of copper sulfide diffusion on PD, voltage-current characteristics under ac and volume resistivity are discussed. Electric field simulation has been used to explain the effects of Cu ions and copper sulfide formation on electric stress distribution across paper. [ABSTRACT FROM AUTHOR]

This paper focuses on the in-depth analysis of the physical mechanism of the broadband frequency domain spectroscopy of oil-paper insulation. The complex permittivity shows two low-frequency dispersion phenomena, and the real part of the complex conductivity exhibits two slope changes under the synergistic effect of aging and moisture. The two slope changes are mainly attributed to the migration characteristics of water molecules and polar aging products with a degradation of the oil-paper insulation, resulting in the transition of the frequency dependence between the DC conductivity and AC conductivity. When the oil-paper insulation deteriorates seriously, the imaginary part of the dielectric modulus shows double relaxation peaks. Physical models of parasitic capacitance and molecular polarity interface polarization are proposed to reveal the physical mechanism of the double relaxation peaks. The left peak of the double relaxation peaks is caused by the accumulation of water molecules and polar aging products at the electrode/insulation interface, and the right peak is due to the charge disturbance of the cellulose molecular chain surface. This paper can provide theoretical support and technical guidance for the condition diagnosis and evaluation of oil-paper insulation. [ABSTRACT FROM AUTHOR]

Measuring the furan concentration in transformer oil is one of the most common methods of monitoring and evaluating insulation paper and estimating its degree of polymerization (DP). Here, methods for measuring furan concentration, especially ultraviolet-visible (UV-Vis) spectroscopy method, are reviewed on the old transformers oil. The results show that the excessive turbidity of old oils and noise at low wavelengths are the main disadvantages of this method, which reduce the measurements accuracy. The following solutions are proposed to overcome these disadvantages: 1) diluting insulation oil with hexane to reduce absorption intensity and 2) using average absorption at a given wavelength to reduce noise impact. These solutions are applied to the oil samples of ten old distribution transformer. It is observed that the correlation between 2-furaldehyde (2-FAL) concentration and average absorption intensity in 190–600 nm wavelength range is equal to ${R}^{{2}} =0.98$. A mathematical equation for calculating 2-FAL concentration based on average absorption is presented. It has been shown that to reduce the test time, a 190–400 nm range is the optimal measurement wavelength range. The results show that the average difference between the values of DP in the proposed method and the direct measurement method is equal to 77.5. [ABSTRACT FROM AUTHOR]

Although the circulating flow of insulating oil can enhance heat dissipation in converter transformers, it can also influence the space charge distribution in oil–paper composite insulation. In this article, the oil–paper composite insulation between flat electrodes was used as the experimental model. Based on the pulsed electroacoustic (PEA) method, we investigated the effect of uncharged flowing oil on the space charge distribution in composite insulation under a dc electric field and polarity reversal. Under a dc electric field, as the oil flow velocity increased, the amount of interface charge between the oil and paper first increased and then decreased. During the polarity reversal process, the field distortion was aggravated at slower oil flows. These experimental results were explained in terms of the effect of oil flow on ionized charges in the oil. [ABSTRACT FROM AUTHOR]

Due to rapid temperature rise and insulation moisture, bubbles can generate in the oil-paper insulation of oil-immersed power transformers, which can reduce the dielectric strength of oil-paper insulation and even bring about the risk of insulation breakdown. In order to accurately evaluate the conditions of bubble formation, the physical process of bubble formation in oil-paper insulation is studied in this article. Considering the effects of water vaporization, gas dissolution in oil, and moisture migration on bubble formation, a bubble formation prediction model is constructed. Based on Henry’s law, the dissolution equilibrium of gas in oil is taken into consideration and the upper boundary of the initial temperature of bubble effect (ITBE) envelope is obtained in this model. Based on the moisture equilibrium in oil-paper insulation, the bubble formation process caused by the emergence and rapid evaporation of free water is analyzed, and then, the lower boundary of the ITBE envelope is obtained in this model. The model results show that the moisture content of the pressboard and the presence of free water have a great impact on ITBE. Specifically, the higher the moisture content, the lower the ITBE value. In addition, with the further increase of moisture content, the upper and lower boundaries of the ITBE envelope gradually tend to be the same. However, once free water is present on the surface of cellulose, ITBE decreases rapidly to below 120 °C. The model built in this article is of great significance to study the temperature limit of the power transformer. Hence the ITBE envelope can provide an important theoretical reference for reducing the risk of bubble formation during power transformer operation. [ABSTRACT FROM AUTHOR]

This Special Section follows from a selection of highly-rated, high impact technical papers presented at the 11th International Conference on Computer-Aided Design for Thin Film Transistor Technologies (CAD-TFT) 2020. The CAD-TFT 2020 was held as a virtual conference on November 10th and 11th, 2020 from the operations center at Tianjin, China. The pre-conference virtual presentations on November 9th, 2020 included six tutorials from internationally recognized experts in their technical fields as well as six posters from China, India, and Canada.

Bubbles, as typical defects of oil–paper insulation systems, pose a great threat to the insulation state. In this article, the characteristics and mechanisms of the partial discharge (PD) inception, evolution, and induced breakdown of bubbles embedded between oil-impregnated paper (OIP) layers are investigated. The results show that the PD inception has a significant statistical time delay due to the lack of free electrons. The PD inception time delay (PDTD) follows an exponential distribution and leads to the large dispersion of the PD inception voltage (PDIV), which follows a Weibull distribution. The changes in PD behavior [charge, repetition rate, pulse current waveform, and phase-resolved PD (PRPD)] over time all show two separable stages (stages 1 and 2). The continuous recording of bubble area and gas composition under PD reveals that the evolution of bubble PD is attributed to the change in gas composition rather than the change in surface conditions as believed by researchers. The OIP breakdown induced by bubble PD indicates two breakdown modes, fast and slow, which correspond to direct-induced breakdown in stage 1 and cumulative-damage breakdown in stage 2. The former occurs because of the severe distortion of the electric field by the space charge at the head of the discharge channel inside the bubble, whereas the latter occurs because of the gradual deterioration of the OIP due to the continuous PD action. This study increases our understanding of the mechanisms of bubble discharge and of oil–paper insulation deterioration, and it provides guidance for fault diagnoses. [ABSTRACT FROM AUTHOR]

Frequency-domain dielectric spectroscopy (FDS) is widely used in the insulation assessment of oil-immersed power equipment, and the moisture in insulating paper could be qualitatively predicted by mathematical approximation. However, due to the still lots unexplored underlying mechanisms, until now, there is still no convincing and physical method for the diagnosis of moisture content. With the aid of spectral decomposition methods, this article aims to explore the effects and mechanism of moisture on the independent dielectric response spectra. First, the measured dielectric response curve is unfolded and reconstructed by derivation of the real part curve. Second, the independent polarization and conductance spectra of damp samples are extracted, and then, the relationships between moisture content in insulating paper and spectral parameters are established quantitatively. The results show that moisture introduces a new polarization in the midfrequency region at room temperature, and both polarization and conductance increase with the moisture content. The multiple adsorption model and the proton exchange model of moisture are employed to illustrate the changes of the polarization and the conductance spectra, respectively. This research provides a methodological reference for the moisture assessment of oil–paper insulation. [ABSTRACT FROM AUTHOR]

The objective of this article is to enhance the dc insulation strength of poly- ${m}$ -phenylene isophthalamide (PMIA) paper by surface treatment. CF4/Ar plasma is used to modify the surface of PMIA paper by fluorination, and the effects of fluorination on the microstructure, electrical parameters, and insulation properties of the material are investigated, and the optimized treatment parameters of CF4 concentration and treatment time are obtained, and the mechanism is further explained from the perspective of carrier traps. The results show that the moderate CF4/Ar plasma treatment can improve the surface insulation properties of PMIA paper without damaging its overall insulation properties. [ABSTRACT FROM AUTHOR]

Timely identification of the aging stage of the transformer can effectively ensure the safe operation of the transformer and prevent the aging fault of the transformer. This work proposes the aging diagnosis of transformer using the Raman spectroscopic recurrence plot combined with learning vector quantization (LVQ) neural network. Oil-paper insulation samples at different aging stages are obtained by accelerated thermal aging tests. Acquisition of Raman spectra of insulating oil is from 800 to 3000 cm−1 and converts to the Raman spectroscopic recurrence plot. The gray-level cooccurrence matrix (GLCM) is used to extract the characteristic information of the Raman spectroscopic recurrence plot. The optimal number of neurons in competitive layer of LVQ neural network is determined by the experimental method. A transformer aging diagnosis model based on the Raman spectroscopic recurrence plot is established. The results show that the diagnostic accuracy of the proposed diagnostic model reached 95%. The Raman spectroscopic recurrence plot has more abundant aging “fingerprint” characteristic information and the proposed diagnostic method shows potential for monitoring oil-paper insulation. [ABSTRACT FROM AUTHOR]

The ecological environment is increasingly damaged due to the impact of mineral oil extraction and leakage. As a kind of sustainable resource, a vegetable oil transformer has bright application prospects in future. However, the stability of vegetable oil has always been a problem to be solved. In addition, the metallic copper inside the transformer has a certain catalytic effect on the deterioration of vegetable oil. In this article, a copper–oil–paper insulation model is established. Based on the molecular dynamics simulation method, the catalytic mechanism of copper on the deterioration of oil-paper insulation is revealed from the microscopic level. Then, the effects of temperature, contact area, and oxygen on the catalytic effect of copper are discussed. The results show that copper could accelerate the decomposition of oil-paper insulation by attracting H atoms and O atoms in oil-paper. The increase in temperature accelerates the progress of the catalytic reaction and aggravates the deterioration of oil-paper insulation. The oxygen concentration has an important influence on the catalytic reaction of copper. As the oxygen concentration increases, the catalytic effect of copper is weakened. The abovementioned research could provide some theoretical reference for further exploration of effective oil-paper insulation deterioration protection technology. [ABSTRACT FROM AUTHOR]

Methanol is considered to be a new chemical marker to estimate the aging state of transformer cellulose insulation paper. The key to improve the assessment accuracy is to establish the precise relationship between the concentration of methanol in oil and degree of polymerization (DP) of insulation paper. The previous research in this area has shortcomings and needs to be further improved. In this article, first, an aging assessment basic model (temperature 20 °C, moisture content of insulation paper 0.637%) is established based on the theoretical derivation of cellulose degradation kinetics, and is calculated by 130 °C thermal aging experiment. Furthermore, the effects of different temperatures (20 °C–90 °C) and moisture contents of insulation paper (0.6%–3.4%) on methanol in oil are studied by diffusion experiment. Based on the above effects, the temperature and moisture correction factors are established by mathematical reduction. What is more, a modified model is proposed by integrating the basic model and the correction factors. Eventually, the verification experiment is randomly prepared to test the accuracy of modified model and the result shows that the relative error of DP is within 7%. The physical meaning and accuracy of aging assessment are improved by model derivation and modification of influencing factors. [ABSTRACT FROM AUTHOR]

Oil impregnated paper in power transformers deteriorates in long-term operation, which leads to the variations of its dielectric characteristics. This paper focuses on investigating the generation mechanism of the dielectric processes in oil impregnated paper and their variations with thermal aging. Firstly, a set of thermally stimulated current tests with bias-voltages were conducted in distinguishing the dielectric processes and revealing their generation mechanism. Secondly, the standard thermally stimulated current spectrum and the M″ spectrum of 0–1000 h aged samples were joint analyzed in investigating the variations of dielectric processes in thermal aging process. Finally, additional experiments of moisture, acidity and microscopic observation were conducted in explaining these variations. It is concluded that three dielectric processes can be found in oil impregnated paper, i.e. the dipole polarization, the interfacial polarization and the electric conduction. These processes are all strengthened with thermal aging. The generation of molecules with strong polarity, the structural changes in insulating paper, and the generation of hydrogen ions are responsible for the strengthening of these processes sequentially. This investigation on distinguishing dielectric processes and obtaining their mechanism can promote further understanding on oil impregnated paper and provide information for insulation design in power transformers. [ABSTRACT FROM PUBLISHER]

Objective: Early stage diagnosis of sepsis without overburdening health services is essential to improving patient outcomes. Methods: A fast and simple-to-use platform that combines an integrated circuit with paper microfluidics for simultaneous detection of multiple-metabolites appropriate for diagnostics was presented. Paper based sensors are a primary candidate for widespread deployment of diagnostic or test devices. However, the majority of devices today use a simple paper strip to detect a single marker using the reflectance of light. However, for many diseases such as sepsis, one biomarker is not sufficient to make a unique diagnosis. In this work multiple measurements are made on patterned paper simultaneously. Using laser ablation to fabricate microfluidic channels on paper provides a flexible and direct approach for mass manufacture of disposable paper strips. A reusable photodiode array on a complementary metal oxide semiconductor chip is used as the transducer. Results: The system measures changes in optical absorbance in the paper to achieve a cost-effective and easily implemented system that is capable of multiple simultaneous assays. Potential sepsis metabolite biomarkers glucose and lactate have been studied and quantified with the platform, achieving sensitivity within the physiological range in human serum. Conclusion: We have detailed a disposable paper-based CMOS photodiode sensor platform for real-time simultaneous detection of metabolites for diseases such as sepsis. Significance: A combination of a low-cost paper strip with microfluidic channels and a sensitive CMOS photodiode sensor array makes our platform a robust portable and inexpensive biosensing device for multiple diagnostic tests in many different applications. [ABSTRACT FROM AUTHOR]

Under long-term synergy effect of multi-factors, especially the thermal stress, insulating paper will be degraded and its insulation performance will decline due to carbonization and degradation of cellulose. This paper presents an optical approach for aging feature extraction of the insulating paper, where one of the image processing methods called texture analysis is utilized. By conducting laboratory accelerated thermal aging tests, insulating paper samples with different aging conditions for both Nomex and Kraft, evaluated with the aging time, are prepared. After taking optical microscopic images of insulating paper samples belong to different aging groups, up to 14 texture features are extracted using the gray-level co-occurrence matrix (GLCM). With different feature selection methods applied, several of them are finally selected to represent the aging condition of insulating. Numerical tests with both supervised and unsupervised algorithms, as well as a linear regression method verifies the validity of these features in characterizing the aging condition of the insulating paper. [ABSTRACT FROM PUBLISHER]

This paper investigates the aging properties of oil-paper insulation under thermocorona discharge. The oil-paper insulation samples were heated and kept at 140°C, and a corona discharge was generated with a needle-plate at a frequency of 15 times/day, with each discharge lasting 5 minutes. The aging properties of oil-paper insulation were investigated by measuring the degree of polymerization (DP) of insulation paper samples along with the furfural content and acid value of the transformer oil samples. The results show that corona discharge at 140°C in oil rapidly decreased the insulation paper DP and increased the furfural content and acid value of the oil compared with thermal aging and corona discharge aging at 20°C. The DP of the insulation paper was reduced to 392.12, the furfural content in oil rose to 33.75 mg/L, and the acid value grew to 4.41 mgKOH/g after 15 days under the combined thermal stress and corona discharge. Both electric and thermal stress accelerated the aging of oil-paper insulation. This research has practical significance for understanding the process of insulation failure caused by the accelerated aging of oil-paper insulation. [ABSTRACT FROM AUTHOR]

The carbon oxides (CO2 and CO) in the insulating oil of power transformers come from the thermal aging of cellulosic insulating paper; the CO2/CO ratio can reflect the aging state of cellulosic insulating paper. At present, the formation mechanisms of CO2 and CO in oil-immersed power transformers are still unclear. In this article, the ReaxFF reaction force field is used to simulate the thermal aging process of cellulosic insulating paper, and the main reaction pathways of CO2 and CO molecules formed by cellulose pyrolysis are obtained. The study finds that the amount of CO2 and CO generated is related to temperature. When the pyrolysis temperature continues to rise, the amount of CO2 generated shows a downward trend, while the amount of CO generated continues to increase, and the CO2/CO ratio continues to decrease. The simulation results are consistent with the previous experimental results. Through pathway tracking, it is found that the CO2 and CO molecules are mainly derived from certain specific atoms of cellulose molecules. The COSMO-RS module is used to analyze the change trend of the solubility of CO2 and CO in insulating oil with temperature. The results show that the solubility of CO2 and CO decreases with the increase of insulating oil temperature, which provides theoretical support for accurate application of carbon oxides aging evaluation index at different temperatures. [ABSTRACT FROM AUTHOR]

Diagnosis of aging of the paper insulation in transformers has long been of interest to transformer manufacturers and utilities [1]-[3]. Such insulation is irreversibly aged during long-term operation, losing its mechanical strength and becoming brittle. The loss of mechanical strength is an important factor limiting the life expectancy of the transformer [4], [5]. Consequently diagnosis of aging and evaluation of residual life of paper insulation is important for the safe operation, condition-based maintenance, and replacement of power transformers [6]-[9]. [ABSTRACT FROM AUTHOR]

Furfural content in oil has been shown to be a powerful indicator of the deterioration of cellulose paper. The furfural content in oil may increase greatly when the moisture content increases in transformers. The increase of furfural content in oil can be attributed to various factors, such as aging of cellulose paper with the increase of moisture content and the difference in furfural production mechanism. In this research, thermal aging tests of oil-paper system with different moisture contents are conducted under laboratory conditions to determine the cause of such increase. Furfural content, both in insulation oil and in insulation paper, and the degree of polymerization values of insulation paper were regularly measured. Results show that the moisture content plays a significant role on the production of furfural, and the high initial moisture content in insulation paper leads to large amount of furfural produced when DP decreases to the same values. The difference in the moisture content apparently affects the distribution of furfural between oil and paper, and the increase in the moisture content in oil-paper system increases the diffusion of furfural from the insulation paper to the oil. [ABSTRACT FROM AUTHOR]